Michael Chan [Wed, 27 Feb 2019 08:58:53 +0000 (03:58 -0500)]
bnxt_en: Drop oversize TX packets to prevent errors.
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Wed, 27 Feb 2019 16:02:11 +0000 (00:02 +0800)]
mmc: core: align max segment size with logical block size
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: linux-block@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:14 +0000 (11:22 -0800)]
mmc: cqhci: Fix a tiny potential memory leak on error condition
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:13 +0000 (11:22 -0800)]
mmc: cqhci: fix space allocated for transfer descriptor
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bart Van Assche [Wed, 27 Feb 2019 00:35:26 +0000 (16:35 -0800)]
scsi: core: Avoid that system resume triggers a kernel warning
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
Cc: Przemek Socha <soprwa@gmail.com> Reported-by: Przemek Socha <soprwa@gmail.com> Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15 Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ritesh Harjani [Fri, 22 Feb 2019 13:51:34 +0000 (19:21 +0530)]
mmc: core: Fix NULL ptr crash from mmc_should_fail_request
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tung Nguyen [Mon, 25 Feb 2019 03:57:20 +0000 (10:57 +0700)]
tipc: fix race condition causing hung sendto
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 22 Feb 2019 18:25:03 +0000 (18:25 +0000)]
hv_netvsc: Fix IP header checksum for coalesced packets
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Feb 2019 21:23:17 +0000 (13:23 -0800)]
Merge branch 'net-fail-route'
David Ahern says:
====================
net: Fail route add with unsupported nexthop attribute
RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.
MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:04 +0000 (09:00 -0800)]
mpls: Return error for RTA_GATEWAY attribute
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:03 +0000 (09:00 -0800)]
ipv6: Return error for RTA_VIA attribute
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:02 +0000 (09:00 -0800)]
ipv4: Return error for RTA_VIA attribute
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Sun [Tue, 26 Feb 2019 14:15:37 +0000 (22:15 +0800)]
bpf: decrease usercnt if bpf_map_new_fd() fails in bpf_map_get_fd_by_id()
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Julia Cartwright [Wed, 20 Feb 2019 16:46:31 +0000 (16:46 +0000)]
iommu/dmar: Fix buffer overflow during PCI bus notification
Commit 57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
Fixes: 57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI device path") Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Takeshi Saito [Thu, 21 Feb 2019 19:38:05 +0000 (20:38 +0100)]
mmc: tmio: fix access width of Block Count Register
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:26 +0000 (08:34 +0100)]
scsi: hptiop: fix calls to dma_set_mask()
The change to use dma_set_mask() incorrectly made a second call with the 32
bit DMA mask value when the call with the 64 bit DMA mask value succeeded.
Fixes: 453cd3700ca3 ("scsi: hptiop: use dma_set_mask") Cc: <stable@vger.kernel.org> Suggested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:25 +0000 (08:34 +0100)]
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA
mask value succeeded.
[mkp: fixed commit message]
Fixes: e4db40e7a1a2 ("scsi: hisi_sas: use dma_set_mask_and_coherent") Cc: <stable@vger.kernel.org> Suggested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:24 +0000 (08:34 +0100)]
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: c22b332d811b ("scsi: csiostor: switch to generic DMA API") Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:23 +0000 (08:34 +0100)]
scsi: bfa: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
[mkp: fixed commit message]
Fixes: a69b080025ea ("scsi: bfa: use dma_set_mask_and_coherent") Cc: <stable@vger.kernel.org> Suggested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:22 +0000 (08:34 +0100)]
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
[mkp: fixed subject]
Fixes: 3a21986f1a59 ("scsi: aic94xx: fully convert to the generic DMA API") Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:21 +0000 (08:34 +0100)]
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: b1fa122930c4 ("scsi: 3w-sas: fully convert to the generic DMA API") Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:20 +0000 (08:34 +0100)]
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded.
Fixes: b000bced5739 ("scsi: 3w-9xxx: fully convert to the generic DMA API") Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 18 Feb 2019 07:34:19 +0000 (08:34 +0100)]
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded. This resulted in NVMe/FC connections failing due to
corrupted data buffers, and various other SCSI/FCP I/O errors.
Fixes: f30e1bfd6154 ("scsi: lpfc: use dma_set_mask_and_coherent") Cc: <stable@vger.kernel.org> Suggested-by: Don Dutile <ddutile@redhat.com> Signed-off-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jonas Gorski [Thu, 21 Feb 2019 09:56:42 +0000 (10:56 +0100)]
MIPS: BCM63XX: provide DMA masks for ethernet devices
The switch to the generic dma ops made dma masks mandatory, breaking
devices having them not set. In case of bcm63xx, it broke ethernet with
the following warning when trying to up the device:
David Howells [Thu, 21 Feb 2019 22:04:32 +0000 (22:04 +0000)]
afs: Fix manually set volume location server list
When a cell with a volume location server list is added manually by
echoing the details into /proc/net/afs/cells, a record is added but the
flag saying it has been looked up isn't set.
This causes the VL server rotation code to wait forever, with the top of
/proc/pid/stack looking like:
Darrick J. Wong [Sat, 23 Feb 2019 06:35:32 +0000 (22:35 -0800)]
tmpfs: fix uninitialized return value in shmem_link
When we made the shmem_reserve_inode call in shmem_link conditional, we
forgot to update the declaration for ret so that it always has a known
value. Dan Carpenter pointed out this deficiency in the original patch.
Fixes: 1062af920c07 ("tmpfs: fix link accounting when a tmpfile is linked in") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Matej Kupljen <matej.kupljen@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Lutomirski [Sat, 23 Feb 2019 01:17:04 +0000 (17:17 -0800)]
x86/uaccess: Don't leak the AC flag into __put_user() value evaluation
When calling __put_user(foo(), ptr), the __put_user() macro would call
foo() in between __uaccess_begin() and __uaccess_end(). If that code
were buggy, then those bugs would be run without SMAP protection.
Fortunately, there seem to be few instances of the problem in the
kernel. Nevertheless, __put_user() should be fixed to avoid doing this.
Therefore, evaluate __put_user()'s argument before setting AC.
This issue was noticed when an objtool hack by Peter Zijlstra complained
about genregs_get() and I compared the assembly output to the C source.
[ bp: Massage commit message and fixed up whitespace. ]
Fixes: 11f1a4b9755f ("x86: reorganize SMAP handling in user space accesses") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20190225125231.845656645@infradead.org
Eric Biggers [Thu, 21 Feb 2019 22:13:56 +0000 (14:13 -0800)]
net: socket: set sock->sk to NULL after calling proto_ops::release()
Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Mon, 25 Feb 2019 15:28:27 +0000 (17:28 +0200)]
net: sched: act_tunnel_key: fix NULL pointer dereference during init
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac5b ("net/sched: fix memory leak in act_tunnel_key_init()") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Mon, 25 Feb 2019 07:22:19 +0000 (15:22 +0800)]
net: dsa: fix a leaked reference by adding missing of_node_put
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
It was well-intentioned, but wrong. Overriding the exception tables for
instructions for random reasons is just wrong, and that is what the new
code did.
It caused problems for tracing, and it caused problems for strncpy_from_user(),
because the new checks made perfectly valid use cases break, rather than
catch things that did bad things.
Unchecked user space accesses are a problem, but that's not a reason to
add invalid checks that then people have to work around with silly flags
(in this case, that 'kernel_uaccess_faults_ok' flag, which is just an
odd way to say "this commit was wrong" and was sprinked into random
places to hide the wrongness).
The real fix to unchecked user space accesses is to get rid of the
special "let's not check __get_user() and __put_user() at all" logic.
Make __{get|put}_user() be just aliases to the regular {get|put}_user()
functions, and make it impossible to access user space without having
the proper checks in places.
The raison d'être of the special double-underscore versions used to be
that the range check was expensive, and if you did multiple user
accesses, you'd do the range check up front (like the signal frame
handling code, for example). But SMAP (on x86) and PAN (on ARM) have
made that optimization pointless, because the _real_ expense is the "set
CPU flag to allow user space access".
Do let's not break the valid cases to catch invalid cases that shouldn't
even exist.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kees Cook <keescook@chromium.org> Cc: Tobin C. Harding <tobin@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
Linus Walleij [Sat, 23 Feb 2019 23:04:52 +0000 (00:04 +0100)]
ARM: dts: gemini: Re-enable display controller
commit 137cd7100ec6fa36d610e106df00acb4d8af99df
"ARM: dts: Enable Gemini flash access" contained a bug
by disabling the display controller, while the whole
idea with the patch was to enable flash access AND
the display controller, simultaneously. Fix it up.
Timur Celik [Sat, 23 Feb 2019 11:53:13 +0000 (12:53 +0100)]
tun: fix blocking read
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 22 Feb 2019 11:33:26 +0000 (12:33 +0100)]
net/sched: act_skbedit: fix refcount leak when replace fails
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda9089 ("net/sched: act_skbedit: don't use spinlock in the data path") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 22 Feb 2019 11:33:25 +0000 (12:33 +0100)]
net/sched: act_ipt: fix refcount leak when replace fails
After commit 4e8ddd7f1758 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f1758 ("net: sched: don't release reference on action overwrite") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Feb 2019 17:47:07 +0000 (09:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Linus Walleij [Sun, 24 Feb 2019 00:11:15 +0000 (01:11 +0100)]
net: phy: realtek: Dummy IRQ calls for RTL8366RB
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Feb 2019 21:24:59 +0000 (13:24 -0800)]
net/x25: fix a race in x25_bind()
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
Fixes: 90c27297a9bf ("X.25 remove bkl in bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 22 Feb 2019 13:22:32 +0000 (21:22 +0800)]
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0") Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: fib_tests: sleep after changing carrier. again.
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Fri, 22 Feb 2019 06:57:23 +0000 (14:57 +0800)]
net: set static variable an initial value in atl2_probe()
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 17:48:01 +0000 (09:48 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 01:46:30 +0000 (17:46 -0800)]
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Linus Torvalds [Sat, 23 Feb 2019 00:31:26 +0000 (16:31 -0800)]
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
Daniel Borkmann [Fri, 22 Feb 2019 23:03:44 +0000 (00:03 +0100)]
bpf, doc: add bpf list as secondary entry to maintainers file
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Sat, 23 Feb 2019 00:12:01 +0000 (16:12 -0800)]
Merge branch 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
Linus Torvalds [Sat, 23 Feb 2019 00:09:55 +0000 (16:09 -0800)]
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
David S. Miller [Sat, 23 Feb 2019 00:05:12 +0000 (16:05 -0800)]
Merge branch 'udp-a-few-fixes'
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:44:00 +0000 (17:44 +0100)]
udp: fix possible user after free in error handler
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:59 +0000 (17:43 +0100)]
udpv6: fix possible user after free in error handler
Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:58 +0000 (17:43 +0100)]
fou6: fix proto error handler argument type
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:57 +0000 (17:43 +0100)]
udpv6: add the required annotation to mib type
In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 21 Feb 2019 14:42:01 +0000 (22:42 +0800)]
mdio_bus: Fix use-after-free on device_register fails
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalash Nainwal [Thu, 21 Feb 2019 00:23:04 +0000 (16:23 -0800)]
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:32 +0000 (19:07 -0500)]
bnxt_en: Wait longer for the firmware message response to complete.
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:31 +0000 (19:07 -0500)]
bnxt_en: Fix typo in firmware message timeout logic.
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang [Fri, 22 Feb 2019 22:36:04 +0000 (22:36 +0000)]
nfp: bpf: fix ALU32 high bits clearance bug
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator") Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Fri, 22 Feb 2019 20:51:21 +0000 (12:51 -0800)]
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 20 Feb 2019 22:58:50 +0000 (14:58 -0800)]
Documentation: networking: switchdev: Update port parent ID section
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID") Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jann Horn [Wed, 20 Feb 2019 21:34:54 +0000 (22:34 +0100)]
net: socket: add check for negative optlen in compat setsockopt
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 20 Feb 2019 17:18:12 +0000 (18:18 +0100)]
ipv6: route: purge exception on removal
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nic: thunderx: fix communication races between VF & PF
The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.
After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.
Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.
This patch series is to address race condition with VF & PF communication.
Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
from int to void;
- 0007: update subject and remove unused variable 'netdev'
from nicvf_link_status_check_task() function;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: remove link change polling code and info from nicpf
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: move link state polling function to VF
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:44 +0000 (11:02 +0000)]
net: thunderx: add mutex to protect mailbox from concurrent calls for same VF
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:44 +0000 (11:02 +0000)]
net: thunderx: add nicvf_send_msg_to_pf result check for set_rx_mode_task
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:43 +0000 (11:02 +0000)]
net: thunderx: make CFG_DONE message to run through generic send-ack sequence
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:43 +0000 (11:02 +0000)]
net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 4974d5f678ab ("net: ip6_gre: initialize erspan_ver just for erspan tunnels") Reported-and-tested-by: syzbot+30191cf1057abd3064af@syzkaller.appspotmail.com Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
George Wilkie [Wed, 20 Feb 2019 08:19:11 +0000 (08:19 +0000)]
team: use operstate consistently for linkup
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e0595 ("team: account for oper state") Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Chen [Wed, 20 Feb 2019 05:47:19 +0000 (13:47 +0800)]
r8152: Fix an error on RTL8153-BD MAC Address Passthrough support
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 19 Feb 2019 23:15:30 +0000 (00:15 +0100)]
ipvlan: disallow userns cap_net_admin to change global mode/flags
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Kwiecien [Fri, 22 Feb 2019 08:45:26 +0000 (09:45 +0100)]
sctp: don't compare hb_timer expire date before starting it
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often") Reported-by: Marcin Stojek <marcin.stojek@nokia.com> Tested-by: Marcin Stojek <marcin.stojek@nokia.com> Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 22 Feb 2019 18:35:06 +0000 (10:35 -0800)]
Merge tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This contains a single i915 tiled display fix, and a set of
amdgpu/radeon fixes.
i915:
- tiled display fix
amdgpu/radeon:
- runtime PM fix
- bulk moves disable (fix is too large for 5.0)
- a set of display fixes that are all cc'ed stable so we didn't want
to leave them until -next"
* tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: disable bulk moves for now
drm/amd/display: set clocks to 0 on suspend on dce80
drm/amd/display: fix optimize_bandwidth func pointer for dce80
drm/amd/display: Fix negative cursor pos programming
drm/i915/fbdev: Actually configure untiled displays
drm/amd/display: Raise dispclk value for dce11
drm/amd/display: Fix MST reboot/poweroff sequence
drm/amdgpu: Update sdma golden setting for vega20
drm/amdgpu: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
gpu: drm: radeon: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
Linus Torvalds [Fri, 22 Feb 2019 18:32:26 +0000 (10:32 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
pretty good here.
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
cxgb4: Export sge_host_page_size to ulds
RDMA/srp: Rework SCSI device reset handling
Yu Zhang [Thu, 31 Jan 2019 16:09:23 +0000 (00:09 +0800)]
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
Previously, commit 7dcd57552008 ("x86/kvm/mmu: check if tdp/shadow
MMU reconfiguration is needed") offered some optimization to avoid
the unnecessary reconfiguration. Yet one scenario is broken - when
cpuid changes VM's maximum physical address width, reconfiguration
is needed to reset the reserved bits. Also, the TDP may need to
reset its shadow_root_level when this value is changed.
To fix this, a new field, maxphyaddr, is introduced in the extended
role structure to keep track of the configured guest physical address
width.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yu Zhang [Thu, 31 Jan 2019 16:09:43 +0000 (00:09 +0800)]
kvm: x86: Return LA57 feature based on hardware capability
Previously, 'commit 372fddf70904 ("x86/mm: Introduce the 'no5lvl' kernel
parameter")' cleared X86_FEATURE_LA57 in boot_cpu_data, if Linux chooses
to not run in 5-level paging mode. Yet boot_cpu_data is queried by
do_cpuid_ent() as the host capability later when creating vcpus, and Qemu
will not be able to detect this feature and create VMs with LA57 feature.
As discussed earlier, VMs can still benefit from extended linear address
width, e.g. to enhance features like ASLR. So we would like to fix this,
by return the true hardware capability when Qemu queries.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>