atl1: remove set but not used variable 'advertising'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_set_link_ksettings':
drivers/net/ethernet/atheros/atlx/atl1.c:3280:6: warning:
variable 'advertising' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/intel/e1000/e1000_main.c: In function 'e1000_watchdog':
drivers/net/ethernet/intel/e1000/e1000_main.c:2436:9: warning:
variable 'txb2b' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 19 Sep 2018 21:42:50 +0000 (14:42 -0700)]
nfp: provide a better warning when ring allocation fails
NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 466271703867 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit. Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors. In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Wed, 19 Sep 2018 12:56:53 +0000 (13:56 +0100)]
ipv6: Allow the l3mdev to be a loopback
There is no way currently for an IPv6 client connect using a loopback
address in a VRF, whereas for IPv4 the loopback address can be added:
$ sudo ip addr add dev vrfred 127.0.0.1/8
$ sudo ip -6 addr add ::1/128 dev vrfred
RTNETLINK answers: Cannot assign requested address
So allow ::1 to be configured on an L3 master device. In order for
this to be usable ip_route_output_flags needs to not consider ::1 to
be a link scope address (since oif == l3mdev and so it would be
dropped), and ipv6_rcv needs to consider the l3mdev to be a loopback
device so that it doesn't drop the packets.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix parameter type for q_id in hclge_tm_q_to_qs_map_cfg()
So far all the places calling hclge_tm_q_to_qs_map_cfg() are assigning
an u16 type value to "q_id", and in the processing of
hclge_tm_q_to_qs_map_cfg(), it also converts the "q_id" to le16.
The max tqp number for pf can be more than 256, we should use "u16" to
store the queue id, instead of "u8", which may cause data lost.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix client initialize state issue when roce client initialize failed
When roce is loaded before nic, the roce client will not be initialized
until nic client is initialized, but roce init flag is set before it.
Furthermore, in this case of nic initialized success and roce failed,
the nic init flag is not set, and roce init flag is not cleared.
This patch fixes it by set init flag only after the client is initialized
successfully.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Clear client pointer when initialize client failed or unintialize finished
If initialize client failed or finish uninitializing client, we should
clear the client pointer. It may cause unexpected result when use
uninitialized client. Meanwhile, we also should check whether client
exist when uninitialize it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix cmdq registers initialization issue for vf
According to hardware's description, the head pointer register should
be written before the tail pointer register while initializing the vf
command queue. Otherwise, it may trigger an interrupt even though there
is no command received.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix for setting speed for phy failed problem
The function of genphy_read_status is that reading phy information
from HW and using these information to update SW variable. If user
is using ethtool to setting the speed of phy and service task is calling
by hclge_get_mac_phy_link, the result of speed setting is uncertain.
Because ethtool cmd will modified phydev and hclge_get_mac_phy_link also
will modified phydev.
Because phy state machine will update phy link periodically, we can
just use phydev->link to check the link status. This patch removes
function call of genphy_read_status. To ensure accuracy, this patch
adds a phy state check. If phy state is not PHY_RUNNING, we consider
link is down. Because in some scenarios, phydev->link may be link up,
but phy state is not PHY_RUNNING. This is just an intermediate state.
In fact, the link is not ready yet.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:53 +0000 (18:29 +0100)]
net: hns3: Check hdev state when getting link status
By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Set STATE_DOWN bit of hdev state when stopping net
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xi Wang [Wed, 19 Sep 2018 17:29:51 +0000 (18:29 +0100)]
net: hns3: Add support for hns3_nic_netdev_ops.ndo_do_ioctl
This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:50 +0000 (18:29 +0100)]
net: hns3: Remove packet statistics of public
All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.
This patch removes all packet statistics of public.
Signed-off-by: Junxin Chen <chenjunxin1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:47 +0000 (18:29 +0100)]
net: hns3: Add default irq affinity
All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sun: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: amd: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: broadcom: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: xilinx: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: toshiba: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: marvell: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: phylink: ensure the carrier is off when starting phylink
Following the discussion we had regarding the phylink issue related to
the carrier link state not being off when starting phylink, I sent a fix
patch a few days ago for the PPv2 driver:
https://lkml.org/lkml/2018/9/14/633
The idea was to send a patch which could go to the stable branches, but
a better solution would be to directly call netif_carrier_off() from
within phylink_start(). This is the aim of this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:39:31 +0000 (11:39 +0200)]
net: phy: phylink: ensure the carrier is off when starting phylink
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: mvpp2: improve the interrupt usage
This series aims to improve the interrupts descriptions and usage in the
Marvell PPv2 driver.
- Before the series interrupts were named after their s/w usage,
which in fact can be configured. The series rename all those
interrupts and add a description of the ones left over.
- In PPv2 the interrupts are mapped to vectors. Those vectors were
directly mapped to a given CPU, and per-cpu accesses were done. While
this worked on our cases, the registers accesses mapped to the vectors
are not actually linked to a given CPU. They instead are linked to
what is called a "s/w thread". The series modify this so that the s/w
threads are used instead of the CPU numbers, by adding an indirection.
This means we now can have systems with more CPUs than s/w threads.
This is based on today's net-next, and was tested on various boards
using both versions of the PPv2 engine.
Two more patches will be coming, to update the device trees describing a
PPv2 engine. The patches are ready, but will go through a different
tree. I'll send them once this series will be accepted. This is not an
issue as the PPv2 driver keeps the dt bindings backward compatibility.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:11 +0000 (11:27 +0200)]
net: mvpp2: rename mvpp2_percpu function to mvpp2_thread
As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:10 +0000 (11:27 +0200)]
net: mvpp2: handle cases where more CPUs are available than s/w threads
The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:04 +0000 (11:27 +0200)]
net: mvpp2: fix the number of queues per cpu for PPv2.2
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:03 +0000 (11:27 +0200)]
net: mvpp2: do not update the queue mode while probing
This patch updates the probing function so that the queue mode isn't
updated while probing, as the driver would silently end up using a
configuration not wanted by the user. The patch adds an extra check to
validate the chosen queue mode instead, and the driver will fail to
probe if the configuration is invalid.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:01 +0000 (11:27 +0200)]
net: mvpp2: rename the IRQs to match the hardware
This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.
The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 09:27:00 +0000 (11:27 +0200)]
net: mvpp2: increase the number of s/w threads to 9
This patch sets the number of s/w threads to 9, its maximum value,
instead of 8. This is not a fix as only 4 of the s/w threads were used
so far, but more could be used in the future.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets from two descriptor to one descriptor because R-Car Gen3
does not have the 4 bytes alignment restriction of the transmission buffer.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Sep 2018 04:06:46 +0000 (21:06 -0700)]
Merge branch 'phy_stop-synchronous'
Heiner Kallweit says:
====================
net: phy: make phy_stop() synchronous
There have been few not that successful attempts in the past to make
phy_stop() a synchronous call instead of just changing the state.
Patch 1 of this series addresses an issue which prevented this change.
At least for me it works fine now. Would appreciate if Geert could
re-test as well that suspend doesn't throw an error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: call state machine synchronously in phy_stop
phy_stop() may be called e.g. when suspending, therefore all needed
actions should be performed synchronously. Therefore add a synchronous
call to the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
When bringing down the netdevice (incl. detaching it) and calling
netif_carrier_off directly or indirectly the latter triggers an
asynchronous linkwatch event.
This linkwatch event eventually may fail to access chip registers in
the ndo_get_stats/ndo_get_stats64 callback because the device isn't
accessible any longer, see call trace in [0].
To prevent this scenario don't check for IFF_UP only, but also make
sure that the netdevice is present.
net: ibm: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: cavium: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, also the implementation in this
driver has returns 'netdev_tx_t' value, so just change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Mon, 17 Sep 2018 10:46:55 +0000 (18:46 +0800)]
veth: rename pcpu_vstats as pcpu_lstats
struct pcpu_vstats and pcpu_lstats have same members and
usage, and pcpu_lstats is used in many files, so rename
pcpu_vstats as pcpu_lstats to reduce duplicate definition
Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 17 Sep 2018 09:57:29 +0000 (11:57 +0200)]
netlink: add ethernet address policy types
Commonly, ethernet addresses are just using a policy of
{ .len = ETH_ALEN }
which leaves userspace free to send more data than it should,
which may hide bugs.
Introduce NLA_EXACT_LEN which checks for exact size, rejecting
the attribute if it's not exactly that length. Also add
NLA_EXACT_LEN_WARN which requires the minimum length and will
warn on longer attributes, for backward compatibility.
Use these to define NLA_POLICY_ETH_ADDR (new strict policy) and
NLA_POLICY_ETH_ADDR_COMPAT (compatible policy with warning);
these are used like this:
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 17 Sep 2018 09:57:28 +0000 (11:57 +0200)]
netlink: add NLA_REJECT policy type
In some situations some netlink attributes may be used for output
only (kernel->userspace) or may be reserved for future use. It's
then helpful to be able to prevent userspace from using them in
messages sent to the kernel, since they'd otherwise be ignored and
any future will become impossible if this happens.
Add NLA_REJECT to the policy which does nothing but reject (with
EINVAL) validation of any messages containing this attribute.
Allow for returning a specific extended ACK error message in the
validation_data pointer.
While at it clear up the documentation a bit - the NLA_BITFIELD32
documentation was added to the list of len field descriptions.
Also, use NL_SET_BAD_ATTR() in one place where it's open-coded.
The specific case I have in mind now is a shared nested attribute
containing request/response data, and it would be pointless and
potentially confusing to have userspace include response data in
the messages that actually contain a request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Sep 2018 02:27:40 +0000 (19:27 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-09-18
This series contains changes to i40evf so that it becomes a more
generic virtual function driver for current and future silicon.
While doing the rename of i40evf to a more generic name of iavf,
we also put the driver on a severe diet due to how much of the
code was unneeded or was unused. The outcome is a lean and mean
virtual function driver that continues to work on existing 40GbE
(i40e) virtual devices and prepped for future supported devices,
like the 100GbE (ice) virtual devices.
This solves 2 issues we saw coming or were already present, the
first was constant code duplication happening with i40e/i40evf,
when much of the duplicate code in the i40evf was not used or was
not needed. The second was to remove the future confusion of why
future VF devices that were not considered "40GbE" only devices
were supported by i40evf.
The thought is that iavf will be the virtual function driver for
all future devices, so it should have a "generic" name to properly
represent that it is the VF driver for multiple generations of
devices.
The last patch in this series is unreleated to the iavf conversion
and just has to do with a MODULE_LICENSE correction.
Known Caveats:
Existing user space configurations may have to change, but the module
alias in patch 1 helps a bit here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.
Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This finishes the process of renaming the files that
make sense to rename (skipping adminq related files that
talk to i40e), and fixes up the build and the #includes
so that everything builds nicely.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the big rename patch, it takes most of the i40e_
and I40E_ strings and renames them to iavf_ and IAVF_.
Some of the adminq code, as well as most of the client
interface code used by RDMA is left unchanged in order
to indicate that the driver is talking to non-internal to
iavf code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename the Intel Ethernet Adaptive Virtual Function driver
(i40evf) to a new name (iavf) that is more consistent with
the ongoing maintenance of the driver as the universal VF driver
for multiple product lines.
This first patch fixes up the directory names and the .ko name,
intentionally ignoring the function names inside the driver
for now. Basically this is the simplest patch that gets
the rename done and will be followed by other patches that
rename the internal functions.
This patch also addresses a couple of string/name issues
and updates the Copyright year.
Also, made sure to add a MODULE_ALIAS to the old name.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
Peter Oskolkov [Mon, 17 Sep 2018 17:20:53 +0000 (10:20 -0700)]
net/ipv6: do not copy dst flags on rt init
DST_NOCOUNT in dst_entry::flags tracks whether the entry counts
toward route cache size (net->ipv6.sysctl.ip6_rt_max_size).
If the flag is NOT set, dst_ops::pcpuc_entries counter is incremented
in dist_init() and decremented in dst_destroy().
This flag is tied to allocation/deallocation of dst_entry and
should not be copied from another dst/route. Otherwise it can happen
that dst_ops::pcpuc_entries counter grows until no new routes can
be allocated because the counter reached ip6_rt_max_size due to
DST_NOCOUNT not set and thus no counter decrements on gc-ed routes.
Fixes: 3b6761d18bc1 ("net/ipv6: Move dst flags to booleans in fib entries") Cc: David Ahern <dsahern@gmail.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: Peter Oskolkov <posk@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
commit 40413955ee26 ("Cipso: cipso_v4_optptr enter infinite loop") fixed
a possible infinite loop in the IP option parsing of CIPSO. The fix
assumes that ip_options_compile filtered out all zero length options and
that no other one-byte options beside IPOPT_END and IPOPT_NOOP exist.
While this assumption currently holds true, add explicit checks for zero
length and invalid length options to be safe for the future. Even though
ip_options_compile should have validated the options, the introduction of
new one-byte options can still confuse this code without the additional
checks.
Signed-off-by: Stefan Nuernberger <snu@amazon.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: Simon Veith <sveith@amazon.de> Cc: stable@vger.kernel.org Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com> Reported-by: Deshu Wen <dwen@sierrawireless.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Reported-by: Fred Veldini <fred.veldini@gmail.com> Reported-by: Deshu Wen <dwen@sierrawireless.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 14 Sep 2018 17:19:16 +0000 (18:19 +0100)]
net: caif: remove redundant null check on frontpkt
It is impossible for frontpkt to be null at the point of the null
check because it has been assigned from rearpkt and there is no
way rearpkt can be null at the point of the assignment because
of the sanity checking and exit paths taken previously. Remove
the redundant null check.
Detected by CoverityScan, CID#114434 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Sep 2018 01:47:58 +0000 (18:47 -0700)]
Merge branch 'r8169-clk-fixes'
Hans de Goede says:
====================
r8169 (x86) clk fixes to fix S0ix not being reached
This series adds code to the r8169 ethernet driver to get and enable an
external clock if present, avoiding the need for a hack in the
clk-pmc-atom driver where that clock was left on continuesly causing x86
some devices to not reach deep power saving states (S0ix) when suspended
causing to them to quickly drain their battery while suspended.
The 3 commits in this series need to be merged in order to avoid
regressions while bisecting. The clk-pmc-atom driver does not see much
changes (it was last touched over a year ago). So the clk maintainers
have agreed with merging all 3 patches through the net tree.
All 3 patches have Stephen Boyd's Acked-by for this purpose.
This v2 of the series only had some minor tweaks done to the commit
messages and is ready for merging through the net tree now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:56 +0000 (11:34 +0200)]
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.
This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:55 +0000 (11:34 +0200)]
r8169: Get and enable optional ether_clk clock
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f9a ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:54 +0000 (11:34 +0200)]
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.
This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>