i40e: Handle PE_CRITERR properly with IWARP enabled
When IWARP is enabled, we weren't clearing the PE_CRITERR, just logging
it and removing it from the mask. We need to do a corer to reset the
PE_CRITERR register, so set the bit for that as we handle the
interrupt.
We should also be checking for the error against the PFINT_ICR0 register,
and only need to clear it in the value getting written to
PFINT_ICR0_ENA.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 7 Jun 2017 09:43:11 +0000 (05:43 -0400)]
i40e: clear only cause_ena bit
When disabling interrupts, we should only be clearing the CAUSE_ENA bit,
not clearing the whole register. Clearing the whole register sets the
NEXTQ_IDX field to 0 instead of 0x7ff which can confuse the Firmware in
some reset sequences.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Brady [Wed, 7 Jun 2017 09:43:10 +0000 (05:43 -0400)]
i40e: fix disabling overflow promiscuous mode
There exists a bug in which the driver does not correctly exit overflow
promiscuous mode. This can occur if "too many" mac filters are added,
putting the driver into overflow promiscuous mode, and the filters are
then removed. When the failed filters are removed, the driver reports
exiting overflow promiscuous mode which is correct, however traffic
continues to be received as if in promiscuous mode still.
The bug occurs because the conditional for toggling promiscuous mode was
set to only execute when promiscuous mode was enabled and not when it
was disabled as well. This patch fixes the conditional to correctly
execute when promiscuous mode is toggled and not just enabled. Without
this patch, the driver is unable to correctly exit overflow promiscuous
mode.
Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Filip Sadowski [Wed, 7 Jun 2017 09:43:09 +0000 (05:43 -0400)]
i40e: Add support for OEM firmware version
This patch adds support for OEM firmware version. If OEM specific
adapter is detected ethtool reports OEM product version in firmware
version string instead of etrack id.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 7 Jun 2017 09:43:08 +0000 (05:43 -0400)]
i40e: genericize the partition bandwidth control
Partition bandwidth control is not in just one form of MFP (multi-function
partitioning), so make the code more generic and be sure to nudge the Tx
scheduler for all MFP.
Copyright updated to 2017.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Bowers [Wed, 7 Jun 2017 09:43:06 +0000 (05:43 -0400)]
i40e: Support firmware CEE DCB UP to TC map re-definition
Changes parsing of FW 4.33 AQ command Get CEE DCBX OPER CFG (0x0A07).
Change is required because FW now creates the oper_prio_tc
nibbles reversed from those in the CEE Priority Group sub-TLV.
This change will only apply to FW 4.33 as future FW versions will use a
different function to parse the CEE data.
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a fix for the static code analysis issue where dcbcfg->numapps
could be greater than size of array (i.e dcbcfg->app[I40E_DCBX_MAX_APPS]).
The fix makes sure that the array is not accessed past the size of
of the array (i.e. I40E_DCBX_MAX_APPS).
Copyright updated to 2017.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 7 Jun 2017 09:43:04 +0000 (05:43 -0400)]
i40e: comment that udp_port must be in host byte order
The firmware expects the port number passed when setting up
the UDP tunnel configuration to be in Little Endian format.
The i40e_aq_add_udp_tunnel command byte swaps the value from
host order to Little Endian.
Since commit fe0b0cd97b4f ("i40e: send correct port number to
AdminQ when enabling UDP tunnels") we've correctly
sent the value in host order.
Let's also add a comment to the function explaining that it must
be in host order, as the port numbers are commonly stored as Big
Endian values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 7 Jun 2017 09:43:03 +0000 (05:43 -0400)]
i40e: use dev_dbg instead of dev_info when warning about missing routine
When searching for the vf_capability client routine, dev_info() was
used, instead of the normal dev_dbg(). This causes the message to be
displayed at standard log levels which can cause administrators to
worry. Avoid this by using dev_dbg instead.
Copyright updated to 2017.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 7 Jun 2017 09:43:02 +0000 (05:43 -0400)]
i40e/i40evf: update WOL and I40E_AQC_ADDR_VALID_MASK flags
Update a few flags related to FW interactions.
Copyright updated to 2017.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable num_active_queues represents the number of active queues we
have for the device. We assign this pretty early in i40evf_init_subtask.
Several code locations are written with loops over the tx_rings and
rx_rings structures, which don't get allocated until
i40evf_alloc_queues, and which get freed by i40evf_free_queues.
These call sites were written under the assumption that tx_rings and
rx_rings would always be allocated at least when num_active_queues is
non-zero.
Lets fix this by moving the assignment into the function where we
allocate queues. We'll use a temporary variable for storage so that we
don't assign the value in the adapter structure until after the rings
have been set up.
Finally, when we free the queues, we'll clear the value to ensure that
we do not loop over the rings memory that no longer exists.
This resolves a possible NULL pointer dereference in
i40evf_get_ethtool_stats which could occur if the VF fails to recover
from a reset, and then a user requests statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Björn Töpel [Wed, 24 May 2017 05:55:35 +0000 (07:55 +0200)]
i40e: add support for XDP_TX action
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Björn Töpel [Wed, 24 May 2017 05:55:34 +0000 (07:55 +0200)]
i40e: add XDP support for pass and drop actions
This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This series includes updates to mlx5 IPoIB netdevice driver (mlx5i),
1. We move ipoib files into separate directory, to allow it to grow
separately in its own space
2. Remove HW update carrier logic from IPoIB and VF representors profiles.
3. Add basic ethtool support. (Rings options/statistics and driver info).
4. Change MTU support.
5. Xmit path statistics reporting.
6. add PTP support.
For the new ethtool ops, PTP (ioctl) and change_mtu ndos in IPoIB, we didn't add new
implementation or new logic, we only reused those callbacks from the already existing
mlx5e (ethernet netdevice profile) and exposed them in IPoIB netdevice/ethtool ops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Jun 2017 19:44:22 +0000 (15:44 -0400)]
Merge branch 's390-net-updates-part-2'
Julian Wiedmann says:
====================
s390/net updates, part 2 (v2)
thanks for the feedback. Here's an updated patchset that honours
the reverse christmas tree and drops the __packed attribute. Please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Jun 2017 14:00:34 +0000 (16:00 +0200)]
s390/qeth: use diag26c to get MAC address on L2
When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Jun 2017 14:00:33 +0000 (16:00 +0200)]
s390/diag: add diag26c support
Implement support for the hypervisor diagnose 0x26c
('Access Certain System Information').
It passes a request buffer and a subfunction code, and receives
a response buffer and a return code.
Also add the scaffolding for the 'MAC Services' subfunction.
It may be used by network devices to obtain a hypervisor-managed
MAC address.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Jun 2017 14:00:32 +0000 (16:00 +0200)]
s390/qeth: fix packing buffer statistics
There's two spots in qeth_send_packet() where we don't accurately
account for transmitted packing buffers in qeth's performance
statistics:
1) when flushing the current buffer due to insufficient size,
and the next buffer is not EMPTY, we need to account for that
flushed buffer.
2) when synchronizing with the TX completion code, we reset
flush_count and thus forget to account for any previously
flushed buffers.
Reported-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 20 Jun 2017 08:05:11 +0000 (16:05 +0800)]
sctp: handle errors when updating asoc
It's a bad thing not to handle errors when updating asoc. The memory
allocation failure in any of the functions called in sctp_assoc_update()
would cause sctp to work unexpectedly.
This patch is to fix it by aborting the asoc and reporting the error when
any of these functions fails.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 20 Jun 2017 08:01:55 +0000 (16:01 +0800)]
sctp: uncork the old asoc before changing to the new one
local_cork is used to decide if it should uncork asoc outq after processing
some cmds, and it is set when replying or sending msgs. local_cork should
always have the same value with current asoc q->cork in some way.
The thing is when changing to a new asoc by cmd SET_ASOC, local_cork may
not be consistent with the current asoc any more. The cmd seqs can be:
The 1st REPLY makes OLD asoc q->cork and local_cork both are 1, and the cmd
DELETE_TCB clears NEW asoc q->cork and local_cork. After asoc goes back to
OLD asoc, q->cork is still 1 while local_cork is 0. The 2nd REPLY will not
set local_cork because q->cork is already set and it can't be uncorked and
sent out because of this.
To keep local_cork consistent with the current asoc q->cork, this patch is
to uncork the old asoc if local_cork is set before changing to the new one.
Note that the above cmd seqs will be used in the next patch when updating
asoc and handling errors in it.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 20 Jun 2017 07:42:38 +0000 (15:42 +0800)]
dccp: call inet_add_protocol after register_pernet_subsys in dccp_v4_init
Now dccp_ipv4 works as a kernel module. During loading this module, if
one dccp packet is being recieved after inet_add_protocol but before
register_pernet_subsys in which v4_ctl_sk is initialized, a null pointer
dereference may be triggered because of init_net.dccp.v4_ctl_sk is 0x0.
Jianlin found this issue when the following call trace occurred:
This patch is to move inet_add_protocol after register_pernet_subsys in
dccp_v4_init, so that v4_ctl_sk is initialized before any incoming dccp
packets are processed.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
With -Wformat-truncation, gcc throws the following warning.
Fix this by increasing the size of devname to accommodate 15 character
netdev interface name and description.
Remove length format precision for %s. We can fit entire name.
Also increment the version.
drivers/net/ethernet/cisco/enic/enic_main.c: In function ‘enic_open’:
drivers/net/ethernet/cisco/enic/enic_main.c:1740:15: warning: ‘%u’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 12 [-Wformat-truncation=]
"%.11s-rx-%u", netdev->name, i);
^~
drivers/net/ethernet/cisco/enic/enic_main.c:1740:5: note: directive argument in the range [0, 16]
"%.11s-rx-%u", netdev->name, i);
^~~~~~~~~~~~~
drivers/net/ethernet/cisco/enic/enic_main.c:1738:4: note: ‘snprintf’ output between 6 and 18 bytes into a destination of size 16
snprintf(enic->msix[intr].devname,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(enic->msix[intr].devname),
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%.11s-rx-%u", netdev->name, i);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Mon, 19 Jun 2017 16:27:53 +0000 (11:27 -0500)]
ibmvnic: Return from ibmvnic_resume if not in VNIC_OPEN state
If the ibmvnic driver is not in the VNIC_OPEN state, return from
ibmvnic_resume callback. If we are not in the VNIC_OPEN state, interrupts
may not be initialized and directly calling the interrupt handler will
cause a crash.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Provide link partner advertising information.
Removed testing for gigabit modes, which is useless for a fast ethernet phy.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net-next: mediatek: various performance improvements
During development we mainly ran testing using iperf doing 1500 byte
tcp frames. It was pointed out recently, that the driver does not perform
very well when using 512 byte udp frames. The biggest problem was that
RPS was not working as no rx queue was being set. fixing this more than
doubled the throughput. Additionally the IRQ mask register is now locked
independently for RX and TX. RX IRQ aggregation is also added. With all
these patches applied we can almost triple the throughput.
While at it we also add PHY status change reporting for GMACs connecting
directly to a PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Mon, 19 Jun 2017 13:37:06 +0000 (15:37 +0200)]
net-next: mediatek: set the rx_queue to 0
The get_rps_cpu() function will not do any RPS on the data flow when no
queue is setup and always use the current cpu where the IRQ was handled
to also handle the backlog. As we only have one physical queue we always
set this to 0 unconditionally.
Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Mon, 19 Jun 2017 13:37:05 +0000 (15:37 +0200)]
net-next: mediatek: split IRQ register locking into TX and RX
Originally the driver only utilised the new QDMA engine. The current code
still assumes this is the case when locking the IRQ mask register. Since
RX now runs on the old style PDMA engine we can add a second lock. This
patch reduces the IRQ latency as the TX and RX path no longer need to wait
on each other under heavy load.
Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Mon, 19 Jun 2017 13:37:04 +0000 (15:37 +0200)]
net-next: mediatek: add RX IRQ delay support
The PDMA engine used for RX allows IRQ aggregation. The patch sets up the
corresponding registers to aggregate 4 IRQs into one. Using aggregation
reduces the load on the core handling to a quarter thus reducing IRQ
latency and increasing RX performance by around 10%.
Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
vxlan: cleanup and IPv6 link-local support
Running VXLANs over IPv6 link-local addresses allows to use them as a
drop-in replacement for VLANs, avoiding to allocate additional outer IP
addresses to run the VXLAN over.
Since v1, I have added a lot more consistency checks to the address
configuration, making sure address families and scopes match. To simplify
the implementation, I also did some general refactoring of the
configuration handling in the new first patch of the series.
The second patch is more cleanup; is slightly touches OVS code, so that
list is in CC this time, too.
As in v1, the last two patches actually make VXLAN over IPv6 link-local
work, and allow multiple VXLANs with the same VNI and port, as long as
link-local addresses on different interfaces are used. As suggested, I now
store in the flags field if the VXLAN uses link-local addresses or not.
v3 removes log messages as suggested by Roopa Prabhu (as it is very unusual
for errors in netlink requests to be printed to the kernel log.) The commit
message of patch 5 has been extended to add a note about IPv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan: allow multiple VXLANs with same VNI for IPv6 link-local addresses
As link-local addresses are only valid for a single interface, we can allow
to use the same VNI for multiple independent VXLANs, as long as the used
interfaces are distinct. This way, VXLANs can always be used as a drop-in
replacement for VLANs with greater ID space.
This also extends VNI lookup to respect the ifindex when link-local IPv6
addresses are used, so using the same VNI on multiple interfaces can
actually work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: David S. Miller <davem@davemloft.net>
If VXLAN is run over link-local IPv6 addresses, it is necessary to store
the ifindex in the FDB entries. Otherwise, the used interface is undefined
and unicast communication will most likely fail.
Support for link-local IPv4 addresses should be possible as well, but as
the semantics aren't as well defined as for IPv6, and there doesn't seem to
be much interest in having the support, it's not implemented for now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* Multicast addresses are never valid as local address
* Link-local IPv6 unicast addresses may only be used as remote when the
local address is link-local as well
* Don't allow link-local IPv6 local/remote addresses without interface
We also store in the flags field if link-local addresses are used for the
follow-up patches that actually make VXLAN over link-local IPv6 work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan: refactor verification and application of configuration
The vxlan_dev_configure function was mixing validation and application of
the vxlan configuration; this could easily lead to bugs with the changelink
operation, as it was hard to see if the function wcould return an error
after parts of the configuration had already been applied.
This commit splits validation and application out of vxlan_dev_configure as
separate functions to make it clearer where error returns are allowed and
where the vxlan_dev or net_device may be configured. Log messages in these
functions are removed, as it is generally unexpected to find error output
for netlink requests in the kernel log. Userspace should be able to handle
errors based on the error codes returned via netlink just fine.
In addition, some validation and initialization is moved to vxlan_validate
and vxlan_setup respectively to improve grouping of similar settings.
Finally, this also fixes two actual bugs:
* if set, conf->mtu would overwrite dev->mtu in each changelink operation,
reverting other changes of dev->mtu
* the "if (!conf->dst_port)" branch would never be run, as conf->dst_port
was set in vxlan_setup before. This caused VXLAN-GPE to use the same
default port as other VXLAN sockets instead of the intended IANA-assigned
4790.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Jun 2017 17:24:44 +0000 (13:24 -0400)]
Merge branch 'net-dsa-Global-2-cosmetics'
Vivien Didelot says:
====================
net: dsa: Global 2 cosmetics
Similarly to what has been done for the Port and Global 1 registers,
this patch series prefixes and documents the macros of Global 2.
It brings no functional changes except for 1/10 which fixes the IRL init
for 88E6390 family.
Changes in v2: make *_g2_irl_init_all static inline without
NET_DSA_MV88E6XXX_GLOBAL2 and compile test with and without the symbol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 19 Jun 2017 14:55:37 +0000 (10:55 -0400)]
net: dsa: mv88e6xxx: clarify SMI PHY functions
Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.
The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.
Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)
Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 19 Jun 2017 14:55:36 +0000 (10:55 -0400)]
net: dsa: mv88e6xxx: add irl_init_all op
Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.
This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.
This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.
A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net-next: stmmac: dwmac-sun8i: add support for V3s
Allwinner V3s features an EMAC like the on in H3, but without external MII
interfaces, so being not able really to use RMII/RGMII.
And it has a different default value of syscon (0x38000 instead of 0x58000
on H3), which shows a problem that the EMAC clock freq should be 24MHz.
(Both H3 and V3s SoCs doesn't have extra xtal input for EPHY, and the
main xtal is 24MHz. The default value of H3 is set to 24MHz, but the V3s
default value is set to 25MHz).
First two patches are device tree binding patches, the third forces
the frequency to 24MHz and the fourth really add the V3s support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Icenowy Zheng [Sat, 17 Jun 2017 14:07:37 +0000 (22:07 +0800)]
net-next: stmmac: dwmac-sun8i: add support for V3s EMAC
Allwinner V3s SoC has an Ethernet MAC and an internal PHY like the ones
in H3 SoC, however the MAC has no external *MII interfaces available at
GPIOs, thus only MII connection to internal PHY is supported.
Add this variant of EMAC to dwmac-sun8i driver.
The default value of the syscon EMAC-related register seems to have
changed from H3, but it seems to be a harmless change.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: David S. Miller <davem@davemloft.net>
Icenowy Zheng [Sat, 17 Jun 2017 14:07:36 +0000 (22:07 +0800)]
net-next: stmmac: dwmac-sun8i: force EPHY clock freq to 24MHz
The EPHY control part of the EMAC syscon register has a bit called
CLK_SEL. On the datasheet it says that if it's 0 the EPHY clock is 25MHz
and if it's 1 the clock is 24MHz.
However, according to the datasheets, no Allwinner SoC with EPHY has any
extra xtal input pins for the EPHY, and the system xtal is 24MHz.
That means the EPHY is not possible to get a 25MHz xtal input, and thus
the frequency can only be 24MHz.
It doesn't matter on H3 as the default value of H3 is 24MHz, however on
V3s the default value is wrongly set to 25MHz, which prevented the EPHY
from working properly.
Force the EPHY clock frequency to 24MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: David S. Miller <davem@davemloft.net>
Icenowy Zheng [Sat, 17 Jun 2017 14:07:34 +0000 (22:07 +0800)]
dt-bindings: net-next: Add DT bindings documentation for Allwinner V3s EMAC
Allwinner V3s SoC has a Ethernet MAC like the one in Allwinner H3, but
have no external MII capability. That means that it can only use the
EPHY and cannot do Gbps transmission.
Add binding for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates [Fri, 16 Jun 2017 21:22:35 +0000 (17:22 -0400)]
selftests: Introduce tc testsuite
Add the beginnings of a testsuite for tc functionality in the kernel.
These are a series of unit tests that use the tc executable and verify
the success of those commands by checking both the exit codes and the
output from tc's 'show' operation.
To run the tests:
# cd tools/testing/selftests/tc-testing
# sudo ./tdc.py
You can specify the tc executable to use with the -p argument on the command
line or editing the 'TC' variable in tdc_config.py. Refer to the README for
full details on how to run.
The initial complement of test cases are limited mostly to tc actions. Test
cases are most welcome; see the creating-testcases subdirectory for help
in creating them.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
qed*: RDMA and infrastructure for iWARP
This series focuses on RDMA in general with emphasis on required changes
toward adding iWARP support. The vast majority of the changes introduced
are in qed/qede, with a couple of small changes to qedr
[mentioned below].
The infrastructure changes:
- Patch #1 adds the ability to pass PBL memory externally for a newly
created chain.
- Patches #4, #5 rename qede_roce.[ch] into qede_rdma.[ch] + change
prefixes from _roce_ to _rdma_, as the API between qede and qedr is
agnostic to the variant of the RDMA protocol used. These patches also
touch qedr [basically to align it with the renaming, nothing more].
- Patch #7 replaces the current SPQ async mechanism into serving
registered callbacks [before adding iWARP which would add another client
in need of this sort of functionallity].
The non-infrastrucutre changes:
- Patches #2, #3 contain DCB-related changes to better align RDMA with
configured DCB.
- Patch #6 contains a minor [mostly theoretical fix] to release flow.
Changes from previous versions
------------------------------
- V4: This is actually a repost of V3 due to some confusion regarding
the sent cover-letter
- V3: Add commit log message in #4 indicating change in header inclusion
- V2: Add several inclusion into qede_rdma.h to have proper declarations
of all variable types used in it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 20 Jun 2017 13:00:06 +0000 (16:00 +0300)]
qed: SPQ async callback registration
Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.
Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 20 Jun 2017 13:00:05 +0000 (16:00 +0300)]
qed: Wait for resources before FUNC_CLOSE
Driver needs to wait for all resources to return from FW before it can send
the FUNC_CLOSE ramrod.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 20 Jun 2017 13:00:04 +0000 (16:00 +0300)]
qed*: Set rdma generic functions prefix
Rename the functions common to both iWARP and RoCE to have a prefix of
_rdma_ instead of _roce_.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 20 Jun 2017 13:00:03 +0000 (16:00 +0300)]
qed*: qede_roce.[ch] -> qede_rdma.[ch]
Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.
While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Delalande [Fri, 16 Jun 2017 01:07:07 +0000 (18:07 -0700)]
tcp: md5: add TCP_MD5SIG_EXT socket option to set a key address prefix
Replace first padding in the tcp_md5sig structure with a new flag field
and address prefix length so it can be specified when configuring a new
key for TCP MD5 signature. The tcpm_flags field will only be used if the
socket option is TCP_MD5SIG_EXT to avoid breaking existing programs, and
tcpm_prefixlen only when the TCP_MD5SIG_FLAG_PREFIX flag is set.
Signed-off-by: Bob Gilligan <gilligan@arista.com> Signed-off-by: Eric Mowat <mowat@arista.com> Signed-off-by: Ivan Delalande <colona@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Delalande [Fri, 16 Jun 2017 01:07:06 +0000 (18:07 -0700)]
tcp: md5: add an address prefix for key lookup
This allows the keys used for TCP MD5 signature to be used for whole
range of addresses, specified with a prefix length, instead of only one
address as it currently is.
Signed-off-by: Bob Gilligan <gilligan@arista.com> Signed-off-by: Eric Mowat <mowat@arista.com> Signed-off-by: Ivan Delalande <colona@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erez Shitrit [Sun, 21 May 2017 05:56:20 +0000 (08:56 +0300)]
net/mlx5e: IPoIB, Handle change_mtu
Add the ndo that supports change mtu for IPoIB.
The callback called from the ipoib ULP driver, that gives the ability to
change the SW and HW resources accordingly in the lower driver.
Erez Shitrit [Thu, 18 May 2017 14:03:21 +0000 (17:03 +0300)]
net/mlx5e: Use hard_mtu as part of the mlx5e_priv struct
The mtu extra space that kept for the HW is specific for each link type,
and it is different in mlx5e and mlx5i modules.
Now it is kept in the priv structures, set by the mlx5e/mlx5i driver
accordingly.
Erez Shitrit [Thu, 18 May 2017 11:32:11 +0000 (14:32 +0300)]
net/mlx5e: Add new profile function update_carrier
Updating the carrier involves specific HW setting, each profile should
use its own function for that.
Both IPoIB and VF representor don't need carrier update function, since
VF representor has only a logical link to VF and IPoIB manages its own
link via ib_core upper layer.
Raju Rangoju [Mon, 19 Jun 2017 12:10:48 +0000 (17:40 +0530)]
cxgb4: notify uP to route ctrlq compl to rdma rspq
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue') Signed-off-by: Raju Rangoju <rajur@chelsio.com> Acked-by: Steve Wise <swise@opengridcomputing.com> CC: Stable <stable@vger.kernel.org> # 4.9+ Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Cascón [Thu, 15 Jun 2017 23:22:15 +0000 (16:22 -0700)]
nfp: add VLAN filtering support
Add general use per-vNIC mailbox area and use it for VLAN filtering
support. Initially proto is hardcoded to 802.1q.
Signed-off-by: Pablo Cascón <pablo.cascon@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Fri, 16 Jun 2017 10:06:09 +0000 (15:36 +0530)]
cxgb4: fix a NULL dereference
Avoid NULL dereference in setup_sge_queues() when the adapter is
in non offload mode.
Fixes: 0fbc81b3ad51 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's') Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liquidio: replace info-pointer mode with buffer-pointer-only mode
Each Octeon output ring can DMA packets to host memory in two modes: info-
pointer mode and buffer-pointer-only mode. In info-pointer mode, Octeon
takes two buffer pointers for each packet and places the length of the
packet along with specified number of bytes from the beginning of the
packet into one buffer and the rest of the packet in a separate buffer. In
buffer-pointer-only mode, Octeon takes single buffer pointer and places the
length of the packet at the beginning of the buffer followed by the packet
data.
This patch switches all Octeon output rings from info-pointer mode to
buffer-pointer-only mode. This results in fewer DMA setups and cache line
snoops.
Signed-off-by: Prasad Kanneganti <pkanneganti@cavium.com> Signed-off-by: Derek Chickles <derek.chickles@cavium.com> Signed-off-by: Satanand Burla <satananda.burla@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liquidio: implement vlan filter enable and disable
Add implementation to support ethtool -K ethX rx-vlan-filter on/off.
Rename OCTNET_CMD_ENABLE_VLAN_FILTER command to OCTNET_CMD_VLAN_FILTER_CTL
and add OCTNET_CMD_VLAN_FILTER_ENABLE and OCTNET_CMD_VLAN_FILTER_DISABLE
parameters so that it can be used to enable or disable the filter.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com> Signed-off-by: Derek Chickles <derek.chickles@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 16 Jun 2017 23:42:11 +0000 (16:42 -0700)]
net: dsa: Fix legacy probing
After commit 6d3c8c0dd88a ("net: dsa: Remove master_netdev and
use dst->cpu_dp->netdev") and a29342e73911 ("net: dsa: Associate
slave network device with CPU port") we would be seeing NULL pointer
dereferences when accessing dst->cpu_dp->netdev too early. In the legacy
code, we actually know early in advance the master network device, so
pass it down to the relevant functions.
Fixes: 6d3c8c0dd88a ("net: dsa: Remove master_netdev and use dst->cpu_dp->netdev") Fixes: a29342e73911 ("net: dsa: Associate slave network device with CPU port") Reported-by: Jason Cobham <jcobham@questertangent.com> Tested-by: Jason Cobham <jcobham@questertangent.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Watson [Sat, 17 Jun 2017 15:25:13 +0000 (08:25 -0700)]
tls: update Kconfig
Missing crypto deps for some platforms.
Default to n for new module.
config: m68k-amcore_defconfig (attached as .config)
compiler: m68k-linux-gcc (GCC) 4.9.0
make.cross ARCH=m68k
All errors (new ones prefixed by >>):
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x732f8): undefined reference to `crypto_alloc_aead'
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x7333c): undefined reference to `crypto_aead_setkey'
net/built-in.o: In function `tls_set_sw_offload':
>> (.text+0x73354): undefined reference to `crypto_aead_setauthsize'
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current mechanism of dst release is a bit complicated. It is because
the users of dst get divided into 2 situations:
1. Most users take the reference count when using a dst and release the
reference count when done.
2. Exceptional users like IPv4/IPv6/decnet/xfrm routing code do not take
reference count when referencing to a dst due to some histotic reasons.
Due to those exceptional use cases in 2, reference count being 0 is not an
adequate evidence to indicate that no user is using this dst. So users in 1
can't free the dst simply based on reference count being 0 because users in
2 might still hold reference to it.
Instead, a dst garbage list is needed to hold the dst entries that already
get removed by the users in 2 but are still held by users in 1. And a periodic
garbage collector task is run to check all the dst entries in the list to see
if the users in 1 have released the reference to those dst entries.
If so, the dst is now ready to be freed.
This logic introduces unnecessary complications in the dst code which makes it
hard to understand and to debug.
In order to get rid of the whole dst garbage collector (gc) and make the dst
code more unified and simplified, we can make the users in 2 also take reference
count on the dst and release it properly when done.
This way, dst can be safely freed once the refcount drops to 0 and no gc
thread is needed anymore.
This patch series' target is to completely get rid of dst gc logic and free
dst based on reference count only.
Patch 1-3 are preparation patches to do some cleanup/improvement on the existing
code to make later work easier.
Patch 4-21 are real implementations.
In these patches, a temporary flag DST_NOGC is used to help transition
those exceptional users one by one. Once every component is transitioned,
this temporary flag is removed.
By the end of this patch series, all dst are refcounted when being used
and released when done. And dst will be freed when its refcount drops to 0.
No dst gc task is running anymore.
Note: This patch series depends on the decnet fix that was sent right before:
"decnet: always not take dst->__refcnt when inserting dst into hash table"
v2:
add curly braces in udp_v4/6_early_demux() in patch 02
add EXPORT_SYMBOL() for dst_dev_put() in patch 05
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:44 +0000 (10:42 -0700)]
net: add debug atomic_inc_not_zero() in dst_hold()
This patch is meant to add a debug warning on the situation where dst is
being held during its destroy phase. This could potentially cause double
free issue on the dst.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:43 +0000 (10:42 -0700)]
net: reorder all the dst flags
As some dst flags are removed, reorder the dst flags to fill in the
blanks.
Note: these flags are not exposed into user space. So it is safe to
reorder.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:42 +0000 (10:42 -0700)]
net: remove DST_NOCACHE flag
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:41 +0000 (10:42 -0700)]
net: remove DST_NOGC flag
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:39 +0000 (10:42 -0700)]
decnet: take dst->__refcnt when struct dn_route is created
struct dn_route is inserted into dn_rt_hash_table but no dst->__refcnt
is taken.
This patch makes sure the dn_rt_hash_table's reference to the dst is ref
counted.
As the dst is always ref counted properly, we can safely mark
DST_NOGC flag so dst_release() will release dst based on refcnt only.
And dst gc is no longer needed and all dst_free() or its related
function calls should be replaced with dst_release() or
dst_release_immediate(). And dst_dev_put() is called when removing dst
from the hash table to release the reference on dst->dev before we lose
pointer to it.
Also, correct the logic in dn_dst_check_expire() and dn_dst_gc() to
check dst->__refcnt to be > 1 to indicate it is referenced by other
users.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Sat, 17 Jun 2017 17:42:38 +0000 (10:42 -0700)]
xfrm: take refcnt of dst when creating struct xfrm_dst bundle
During the creation of xfrm_dst bundle, always take ref count when
allocating the dst. This way, xfrm_bundle_create() will form a linked
list of dst with dst->child pointing to a ref counted dst child. And
the returned dst pointer is also ref counted. This makes the link from
the flow cache to this dst now ref counted properly.
As the dst is always ref counted properly, we can safely mark
DST_NOGC flag so dst_release() will release dst based on refcnt only.
And dst gc is no longer needed and all dst_free() and its related
function calls should be replaced with dst_release() or
dst_release_immediate().
The special handling logic for dst->child in dst_destroy() can be
replaced with a simple dst_release_immediate() call on the child to
release the whole list linked by dst->child pointer.
Previously used DST_NOHASH flag is not needed anymore as well. The
reason that DST_NOHASH is used in the existing code is mainly to prevent
the dst inserted in the fib tree to be wrongly destroyed during the
deletion of the xfrm_dst bundle. So in the existing code, DST_NOHASH
flag is marked in all the dst children except the one which is in the
fib tree.
However, with this patch series to remove dst gc logic and release dst
only based on ref count, it is safe to release all the children from a
xfrm_dst bundle as long as the dst children are all ref counted
properly which is already the case in the existing code.
So, this patch removes the use of DST_NOHASH flag.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>