Patrice Chotard [Wed, 10 Jan 2018 08:21:02 +0000 (09:21 +0100)]
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
Viresh Kumar [Thu, 11 Jan 2018 05:58:52 +0000 (11:28 +0530)]
arm: spear13xx: Fix dmas cells
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+ Fixes: 6e8887f60f60 ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Wed, 10 Jan 2018 21:06:48 +0000 (22:06 +0100)]
arm64: dts: add #cooling-cells to CPU nodes
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Olof Johansson [Fri, 12 Jan 2018 01:38:33 +0000 (17:38 -0800)]
Merge tag 'samsung-dt64-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM64 changes for v4.16, part 2
1. Fix DTC warnings around unit addresses.
2. Add SPDX license identifiers.
* tag 'samsung-dt64-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add SPDX license identifiers
arm64: dts: exynos: Fix typo in MSCL clock controller unit address of Exynos5433
arm64: dts: exynos: Use lower case hex addresses in node unit addresses
Olof Johansson [Fri, 12 Jan 2018 00:54:36 +0000 (16:54 -0800)]
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Arnd Bergmann [Thu, 21 Dec 2017 21:30:07 +0000 (22:30 +0100)]
ARM: dts: exynos: fix RTC interrupt for exynos5410
According to the comment added to exynos_dt_pmu_match[] in commit 8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b062 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC. The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Yixun Lan [Sat, 16 Dec 2017 03:55:27 +0000 (11:55 +0800)]
ARM64: dts: meson-axg: enable ethernet for A113D S400 board
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Yixun Lan [Sat, 16 Dec 2017 03:55:26 +0000 (11:55 +0800)]
ARM64: dts: meson-axg: add ethernet mac controller
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sunny Luo [Fri, 15 Dec 2017 14:42:17 +0000 (22:42 +0800)]
ARM64: dts: meson-axg: add the SPICC controller
Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Yixun Lan [Fri, 15 Dec 2017 14:17:41 +0000 (22:17 +0800)]
arm64: dts: meson-axg: switch uart_ao clock to CLK81
Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Kevin Hilman [Fri, 5 Jan 2018 23:27:02 +0000 (15:27 -0800)]
Merge tag 'meson-clk-headers-for-v4.16-2' of git://github.com/BayLibre/clk-meson into v4.16/dt64
Add axg compatible string and device tree bindings
* tag 'meson-clk-headers-for-v4.16-2' of git://github.com/BayLibre/clk-meson:
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
Arnd Bergmann [Fri, 5 Jan 2018 16:17:25 +0000 (17:17 +0100)]
Merge tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Ethernet aliases
arm64: dts: marvell: replace cpm by cp0, cps by cp1
arm64: dts: marvell: de-duplicate CP110 description
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
arm64: dts: marvell: use mvebu-icu.h where possible
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
arm64: dts: marvell: fix typos in comment describing the NAND controller
arm64: dts: marvell: use lower case for unit address and reg property
arm64: dts: marvell: fix watchdog unit address in Armada AP806
arm64: dts: marvell: armada-37xx: add a crypto node
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
Arnd Bergmann [Fri, 5 Jan 2018 16:07:32 +0000 (17:07 +0100)]
Merge tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.16" from Shawn Guo:
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
ARM: dts: imx7s: Avoid using label in unit address and reg
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
ARM: dts: vf610-zii-dev: enable edma1
ARM: dts: ls1021a-twr: Remove extra clock cell
ARM: dts: ls1021a-qds: Remove extra clock cell
ARM: dts: imx53: add srtc node
dt-bindings: imx-gpcv2: Fix the unit address
ARM: imx: dts: Use lower case for bindings notation
ARM: dts: imx6q-h100: use usdhc2 VSELECT
ARM: dts: imx6sx: Add support for PCI power domain
ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
ARM: dts: imx6qdl-hummingboard2: add PWM3 support
...
Arnd Bergmann [Fri, 5 Jan 2018 16:06:04 +0000 (17:06 +0100)]
Merge tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "ASPEED device tree updates for 4.16" from Joel Stanley:
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
Yan Markman [Wed, 3 Jan 2018 15:18:52 +0000 (16:18 +0100)]
arm64: dts: marvell: add Ethernet aliases
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes] Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
arm64: dts: marvell: replace cpm by cp0, cps by cp1
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Suggested-by: Hanna Hawa <hannah@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit] Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
arm64: dts: marvell: use mvebu-icu.h where possible
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742c8 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock") Cc: stable@vger.kernel.org Reported-by: Riku Voipio <riku.voipio@linaro.org> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
MPP7 is currently muxed as "gpio", but this function doesn't exist for
MPP7, only "gpo" is available. This causes the following error:
kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7
pinctrl core: failed to register map default (6): invalid type given
kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22
kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22
kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver
kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22
So the pinctrl driver is not probed, all device drivers (including the
UART driver) do a -EPROBE_DEFER, and therefore the system doesn't
really boot (well, it boots, but with no UART, and no devices that
require pin-muxing).
Back when the Device Tree file for this board was introduced, the
definition was already wrong. The pinctrl driver also always described
as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11,
a hog pin failing to be muxed was turned from a simple warning to a
hard error that caused the entire pinctrl driver probe to bail
out. This is probably the result of commit 6118714275f0a ("pinctrl:
core: Fix pinctrl_register_and_init() with pinctrl_enable()").
This commit fixes the Device Tree to use the proper "gpo" function for
MPP7, which fixes the boot of OpenBlocks A7, which was broken since
Linux 4.11.
Fixes: f24b56cbcd9d ("ARM: kirkwood: add support for OpenBlocks A7 platform") Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Linus Walleij [Tue, 2 Jan 2018 07:57:17 +0000 (08:57 +0100)]
ARM: dts: Delete bogus reference to the charlcd
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Olof Johansson [Fri, 5 Jan 2018 07:30:28 +0000 (23:30 -0800)]
Merge tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.16
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
* tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers
ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers
ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: vinco: use TCB2 as timers
ARM: dts: at91: ma5d4: use TCB2 as timers
ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers
ARM: dts: at91: sama5d4ek: use TCB2 as timers
ARM: dts: at91: sama5d4: Add TCB2
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: linea/tse850-3: use TCB0 as timers
ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers
ARM: dts: at91: kizbox2: use TCB0 as timers
ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d3xek: use TCB0 as timers
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: kizboxmini: use TCB0 as timers
ARM: dts: at91: cosino: use TCB0 as timers
ARM: dts: at91: acme/g25: use TCB0 as timers
ARM: dts: at91: at91sam9x5cm: use TCB0 as timers
...
Olof Johansson [Fri, 5 Jan 2018 07:29:34 +0000 (23:29 -0800)]
Merge tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.16
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
* tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
arm64: dts: uniphier: add GPIO hog definition for PXs3
arm64: dts: uniphier: use macros in dt-bindings header
Olof Johansson [Fri, 5 Jan 2018 07:28:00 +0000 (23:28 -0800)]
Merge tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.16
- clean up gpios properties by macro
- add efuse nodes
- add has-transaction-translator property to generic-ehci nodes
* tag 'uniphier-dt-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add has-transaction-translator property to usb node for LD4, sLD8 and Pro4
ARM: dts: uniphier: add efuse node for UniPhier 32bit SoC
ARM: dts: uniphier: use macros in dt-bindings header
Olof Johansson [Fri, 5 Jan 2018 07:18:15 +0000 (23:18 -0800)]
Merge tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT64 changes for 4.16
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
Olof Johansson [Fri, 5 Jan 2018 07:17:16 +0000 (23:17 -0800)]
Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
* tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1
ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings
ARM: dts: sun8i: a83t: Add I2S controller device nodes
ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY
ARM: dts: sun8i: a83t: Enable Ethernet on two boards
ARM: dts: sun8i: a83t: add dwmac-sun8i device node
ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board
ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.
ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
ARM: dtsi: axp81x: add GPIO DT node
ARM: dts: sun8i: add support for Orange Pi R1
ARM: dts: sunxi: Add codec for A13 Olinuxino
Olof Johansson [Fri, 5 Jan 2018 07:12:16 +0000 (23:12 -0800)]
Merge tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
ARM: Keystone DTS update for 4.16
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
* tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2l-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-hk-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone: Add missing unit name to interrupt controller
ARM: dts: keystone: Get rid of usage of skeleton.dtsi
ARM: dts: keystone*: Use a single soc0 instance
ARM: dts: keystone*: Standardize license with SPDX tag
ARM: dts: k2g-evm: Enable UART 2
ARM: dts: k2g: Add UART 1 and 2 instances
ARM: dts: keystone: Add generic compatible string for I2C EEPROM
ARM: dts: keystone-k2g-ice: Add DT nodes for few peripherals
ARM: dts: keystone-k2g-evm: Add QSPI DT node.
ARM: dts: keystone-k2g: Move ti,non-removable property to board dts
ARM: dts: keystone-k2g-evm: Fix botched up merge
ARM: dts: keystone-k2g: Add QSPI DT entry
ARM: dts: keystone-k2l: Add the second gpio bank node
Olof Johansson [Fri, 5 Jan 2018 06:58:00 +0000 (22:58 -0800)]
Merge tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.16 (part 1)
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
* tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Add thermal support for A7K/A8K
arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support
arm64: dts: marvell: add NAND support on the 8040-DB board
Olof Johansson [Fri, 5 Jan 2018 06:52:45 +0000 (22:52 -0800)]
Merge tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.16 (part 1)
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
* tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu:
arm: kirkwood: dts: Use lower case for bindings notation
ARM: dts: armada-38x: Add NAND RB pinctrl information
Olof Johansson [Fri, 5 Jan 2018 06:51:06 +0000 (22:51 -0800)]
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.16
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
* tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits)
ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core
ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support on DTS
ARM: dts: iwg22d-sodimm: Sound PIO support
ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec
ARM: dts: r8a7745: Add sound support
ARM: dts: r8a7745: Add audio DMAC support
ARM: dts: r8a7745: Add audio clocks
ARM: dts: r8a7740: Correct TPU register block size
ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus
ARM: dts: r8a7743: sort root sub-nodes alphabetically
ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support on DTS
ARM: dts: iwg20d-q7-common: Sound PIO support
ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec
ARM: dts: r8a7792: move timer node out of bus
...
Olof Johansson [Fri, 5 Jan 2018 06:38:49 +0000 (22:38 -0800)]
Merge tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.16
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
* tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: salvator-common: enable usb3_peri0
arm64: dts: renesas: salvator-common: enable usb3_phy0 node
arm64: dts: renesas: r8a7796: add usb3_phy node
arm64: dts: renesas: r8a7795: add usb3_phy node
arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes
arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus
arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically
arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically
arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset
arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset
arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus
Olof Johansson [Fri, 5 Jan 2018 06:35:13 +0000 (22:35 -0800)]
Merge tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.16
- Add SD card support for the hi3798cv200-poplar board
- Replace the PMU node with exact match for the hi3660 SoC
- Add cpu capacity-dmips-mhz information for the hi3660 SoC
* tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
arm64: dts: hi3660: improve pmu description
arm64: dts: hi3798cv200: add SD card support
Arnd Bergmann [Thu, 4 Jan 2018 22:55:52 +0000 (23:55 +0100)]
arm64: dts: sprd: remove broken header inclusion
The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:
In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory
It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.
Maxime Ripard [Thu, 21 Dec 2017 11:02:35 +0000 (12:02 +0100)]
ARM: dts: sun8i: a83t: Add display pipeline
The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.
Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Arnd Bergmann [Thu, 4 Jan 2018 16:55:54 +0000 (17:55 +0100)]
Merge tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "A second set of Gemini DTS updates for v4.16" from Linus Walleij:
- Use Open Drain flags properly for emulated I2C
- Add the PCI bus to WBD111 and WBD222
- Enable the TVE and panel on DIR-685; the panel driver and
bindings have been merged into the DRI subsystem.
* tag 'gemini-dts-update-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add TVE/TVC and ILI9322 panel to DIR-685
ARM: dts: Add PCI to WBD111 and WBD222
ARM: dts: Flags D-Link DIR-685 I2C bus gpios
Chunyan Zhang [Thu, 7 Dec 2017 12:57:15 +0000 (20:57 +0800)]
arm64: dts: add clocks for SC9860
Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.
Chunyan Zhang [Thu, 7 Dec 2017 12:57:14 +0000 (20:57 +0800)]
arm64: dts: add syscon for whale2 platform
Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.
arm64: dts: exynos: Use lower case hex addresses in node unit addresses
Convert all hex addresses in node unit addresses to lower case to
fix warnings like:
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dtb: Warning (simple_bus_reg):
Node /soc/video-scaler@13C00000 simple-bus unit address format error, expected "13c00000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm64/boot/dts/exynos/*.dts*
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Damien Riegel [Thu, 7 Dec 2017 15:19:40 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916-pins: move sdhc2 cd node with its siblings
Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.
Damien Riegel [Thu, 7 Dec 2017 15:19:41 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916: normalize I2C and SPI nodes
The QUP core can be used either for I2C or SPI, so the same IP is mapped
by a driver or the other. SPI bindings use a leading 0 for the start
address and a size of 0x600, I2C bindings don't have the leading 0 and
have a size 0x1000.
To make them more similar, add the leading 0 to I2C bindings and changes
the size to 0x500 for all of them, as this is the actual size of these
blocks. Also align the second entry of the clocks array.
Damien Riegel [Thu, 7 Dec 2017 15:19:36 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916: drop unused board-specific nodes
These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.
Damien Riegel [Thu, 7 Dec 2017 15:19:34 +0000 (10:19 -0500)]
arm64: dts: qcom: msm8916-pins: remove assignments to bias-disable
Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.
Indentation did not respect kernel standards, so fix that for the usual
indent with tabs, align with spaces. While at it, remove some empty
lines before and after the closing parenthesis of this block.
Bjorn Andersson [Fri, 1 Dec 2017 05:27:32 +0000 (21:27 -0800)]
arm64: dts: msm8916: Correct ipc references for smsm
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9ba4 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes") Cc: stable@vger.kernel.org Reported-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>