Olof Johansson [Tue, 27 Jan 2015 02:41:45 +0000 (18:41 -0800)]
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.20" from Kukjin Kim:
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Configure regulators for suspend on exynos Peach boards
ARM: dts: Set Peach boards USB WebCam regulators to always on
ARM: dts: Add lid GPIO key device node for Peach boards
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
Documentation: dt-bindings: add exynos-chipid binding information
ARM: dts: add Panel device support for exynos3250-rinato
ARM: dts: add fimd device support for exynos3250-rinato
ARM: dts: use macro in gpio keys for exynos3250 boards
ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
ARM: dts: Enable USB node for exynos3250-monk
ARM: dts: Enable USB node for exynos3250-rinato
ARM: dts: Add hsotg node for exynos3250
ARM: dts: Add exynos_usbphy node for exynos3250
ARM: dts: Add dts file for Odroid XU3 board
Olof Johansson [Fri, 23 Jan 2015 22:51:41 +0000 (14:51 -0800)]
Merge tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v3.20" from Thierry Reding:
A couple of unit addresses fixes in device trees, addition of microphone
detection on Chromebook 13 and a vendor prefix update.
* tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update isl29028 compatible string to use isil vendor prefix
ARM: tegra: Fix unit address for Cortex-A9 TWD timer
ARM: dts: tegra20: fix GR3D, DSI unit and reg base addresses
ARM: tegra: Enable the mic-detect gpio on Acer Chromebook 13
Olof Johansson [Fri, 23 Jan 2015 22:44:16 +0000 (14:44 -0800)]
Merge tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Olof Johansson [Fri, 23 Jan 2015 22:17:15 +0000 (14:17 -0800)]
Merge tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu/dt #2" from Andrew Lunn:
Second set of dt patches for mvebu for v3.20.
* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
Olof Johansson [Fri, 23 Jan 2015 21:58:01 +0000 (13:58 -0800)]
Merge tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.20" from Hauke Mehrtens:
bcm5301x-dt-2015-01-20: ARM: BCM5301X: dts updates for 3.20
* tag 'bcm5301x-dt-2015-01-20' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-900DHP
ARM: BCM5301X: Add LEDs for Buffalo devices
ARM: BCM5301X: Drop unused poll-interval from gpio-keys
ARM: BCM5301X: Add DT for Luxul XWC-1000
Olof Johansson [Thu, 22 Jan 2015 01:03:01 +0000 (17:03 -0800)]
Merge tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/dt
Merge "qcom DT changes for v3.20" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.20
* Correct IPQ8064 tlmm interrupt
* Add Support for SD Card Detect for ifc6410 board
* tag 'qcom-dt-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
ARM: dts: qcom: Add Support for SD Card Detect for ifc6410 board
Olof Johansson [Thu, 22 Jan 2015 01:00:47 +0000 (17:00 -0800)]
Merge tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v3.20" from Simon
Horman:
* Support Renesas memory controllers
* Add SRC interrupt number on r8a779~ and r8a7791 SoCs
* Fix MSTP8 input clocks on r8a7791 SoC
* Add PM domain support to r8a7740
* Add DT bindings for the R-Mobile System Controller
* Use Add sh73a0-specific FSI2 compatible property
* tag 'renesas-dt2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PM / Domains: R-Mobile SYSC: Document SH-Mobile AG5 (sh73a0) binding
ARM: shmobile: sh73a0 dtsi: Add memory-controller nodes
ARM: shmobile: r8a7740 dtsi: Add memory-controller node
ARM: shmobile: r8a73a4 dtsi: Add memory-controller nodes
ARM: shmobile: Add DT bindings for Renesas memory controllers
ARM: shmobile: r8a7791: add SRC interrupt number on DTSI
ARM: shmobile: r8a7790: add SRC interrupt number on DTSI
ARM: shmobile: r8a7791: fix MSTP8 input clocks
ARM: shmobile: r8a7740 dtsi: Add PM domain support
PM / Domains: Add DT bindings for the R-Mobile System Controller
ARM: shmobile: sh73a0 dtsi: Add SoC-specific FSI2 compatible property
Paul Bolle [Mon, 19 Jan 2015 19:40:25 +0000 (20:40 +0100)]
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
The Kconfig symbol DEBUG_MVEBU_UART_ALTERNATE was renamed to
DEBUG_MVEBU_UART0_ALTERNATE. And the symbol DEBUG_MVEBU_UART1_ALTERNATE
was added to allow UART1 as a DEBUG_LL target. Make the comment at the
top of this DTS reflect those changes.
Since we're touching this DTS add comments to show which blocks describe
UART0 and UART1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line] Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Wang Long [Wed, 24 Dec 2014 03:09:58 +0000 (03:09 +0000)]
ARM: dts: Add hip01-ca9x2 dts file
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch] Signed-off-by: Olof Johansson <olof@lixom.net>
Stefan Agner [Fri, 16 Jan 2015 17:06:15 +0000 (18:06 +0100)]
ARM: vf610: use zero based naming for GPIO nodes
On Vybrid, all peripherals are numbered starting with zero,
including the GPIO and PORT module. However, the labels of the
corresponding device tree nodes start with one, which is confusing.
Fix that by renaming the labels of the gpio nodes in the device
tree.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Olof Johansson [Tue, 20 Jan 2015 00:32:42 +0000 (16:32 -0800)]
ARM: dts: move alphascale in makefile
The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.
Also linewrap like other entries have been lately.
Tony Lindgren [Mon, 19 Jan 2015 19:47:35 +0000 (11:47 -0800)]
ARM: dts: Add basic clocks for dm816x
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Mon, 19 Jan 2015 19:21:25 +0000 (11:21 -0800)]
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Olof Johansson [Mon, 19 Jan 2015 18:57:35 +0000 (10:57 -0800)]
Merge tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Stephen Boyd [Fri, 5 Dec 2014 20:53:33 +0000 (12:53 -0800)]
ARM: dts: qcom: Correct IPQ8064 tlmm interrupt
The interrupt is 16, not 32 (which it would be if we include PPIs
in the count of interrupts).
Cc: Andy Gross <agross@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Tested-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Kumar Gala <galak@codeaurora.org>
The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Maxime COQUELIN [Fri, 9 Jan 2015 15:11:00 +0000 (16:11 +0100)]
ARM: dts: STiH418: Add B2199 board support
B2199 HDK is the reference board for STiH418 SoC.
It has the following characteristics:
- 3GB DDR3
- 8GB eMMC / SD-Card slot
- 32MB NOR Flash
- 1 x Gbit Ethernet
- 1 x USB3.0 port
- 2 x USB2.0 ports
- 1 x Sata or Mini-PCIe port
- 1 x WiFi 802.11ac (Quantenna)
- 1 x HDMI out
- 1 x HDMI in
- 1 x SPDIF
Reviewed-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the DRM/KMS dt nodes.
This node can't be in stih407-family.dtsi file because in the future we
will integrate a new stih418-b2199 board. It's a stih407 family board
with different drm/kms dt nodes.
That is why i created the stih407.dtsi file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Josh Wu [Sun, 4 Jan 2015 09:02:31 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.
We change its name to: pinctrl_pck1_as_isi_mck.
As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Josh Wu [Sun, 4 Jan 2015 09:02:30 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.
This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Bo Shen [Sun, 4 Jan 2015 09:02:27 +0000 (17:02 +0800)]
ARM: at91: dts: sama5d3: split isi pinctrl
As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The ethernut5 is actually based on an at91sam9xe, use the correct dts include.
Cc: Martin Reimann <martin.reimann@egnite.de> Cc: Tim Schendekehl <tim.schendekehl@egnite.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.
Also remove leftover TODOs in the sam9g45 file
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Olof Johansson [Thu, 15 Jan 2015 01:12:44 +0000 (17:12 -0800)]
Merge tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu: dt for v3.20" from Andrew Lunn:
mvebu dt changes for v3.20 (part #1)
- Add Armada 388 General Purpose Development Board support
- Add Device Tree description of the Armada 388 SoC
- Document the Device Tree binding for the Armada 388 SoC
- a38x: Add missing labels
- a38x: Add more pinctrl functions
- Add Armada 385 Access Point Development Board support
- Add a number of pinctrl functions
- A38x: Remove redundant pinctrl informations
- a38x: Fix node names
- Add support for Seagate BlackArmor NAS220
- kirkwood: enable phy driver for SATA controller on 88f6192
- gpio_poweroff support for Iomega ix2-200
- Use all remaining MTD space foor rootfs of Iomega ix2-200
* tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add Armada 388 General Purpose Development Board support
ARM: mvebu: Add Device Tree description of the Armada 388 SoC
ARM: mvebu: Document the Device Tree binding for the Armada 388 SoC
ARM: mvebu: a38x: Add missing labels
ARM: mvebu: a38x: Add more pinctrl functions
ARM: mvebu: Add Armada 385 Access Point Development Board support
ARM: mvebu: Add a number of pinctrl functions
ARM: mvebu: A38x: Remove redundant pinctrl informations
ARM: mvebu: a38x: Fix node names
Kirkwood: add support for Seagate BlackArmor NAS220
ARM: dts: kirkwood: enable phy driver for SATA controller on 88f6192
ARM: dts: add gpio_poweroff support for Iomega ix2-200
ARM: dts: use all remaining MTD space foor rootfs of Iomega ix2-200
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Olof Johansson <olof@lixom.net>
Add device nodes for the two SDRAM Bus State Controllers.
The SBSCs are located in the A4BC0 resp. A4BC1 PM domains, which must
not be powered down, else the system will crash.
References to the A4BC0 and A4BC1 PM domains will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the DDR3 Bus State Controller (DBSC3).
The DBSC3 is located in the A4S PM domain, which must not be powered
down, else the system will crash.
This has no visible effect for now, as A4S was never turned off anyway
because its child PM domain A3SM contains the CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the two DDR Bus State Controllers (DBSC).
The DBSCs are located in the A3BC PM domain, which must not be powered
down, else the system will crash.
A reference to the A3BC PM domain will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: Add DT bindings for Renesas memory controllers
Add DT bindings for Renesas R-Mobile and SH-Mobile memory controllers.
Currently memory controller device nodes are used only to reference PM
domains, and prevent these PM domains from being powered down, which
would crash the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: dts: Configure regulators for suspend on exynos Peach boards
The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.
To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
ARM: dts: Set Peach boards USB WebCam regulators to always on
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
ARM: dts: Add lid GPIO key device node for Peach boards
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have both
a power and lid GPIO keys but only the former was defined in the
DTS. Add DTS snippets for the lid GPIO key too. These were taken
from the downstream ChromeOS 3.8 kernel tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
The Exynos5250 Snow Chromebook has GPIO keys for power and lid
so the SoC I/O pins have to be configured in external interrupt
mode. Currently, this is working without setting the pinctrl
lines but is better to set it explicitly instead of relying on
the previous state of the I/O pins.
The DTS snippets were taken from the downstream ChromeOS tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org>
Zhiwu Song [Thu, 25 Dec 2014 08:34:19 +0000 (16:34 +0800)]
ARM: dts: add init dts file for CSR atlas7 SoC
CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens
of MARCOs, in each MARCO, there are dozens of hardware modules.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com> Signed-off-by: Hao Liu <Hao.Liu@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
Sergei Shtylyov [Mon, 12 Jan 2015 22:31:14 +0000 (01:31 +0300)]
ARM: shmobile: r8a7791: fix MSTP8 input clocks
I made a mistake when rebasing Andrey Gusakov's patch adding MLB+ clock to the
R8A7791 device tree, inserting <&hp_clk> into the "clocks" property of the
MSTP8 node at a wrong position, so that the input clocks for MLB+ and IPMMU-SGX
got swapped...
Fixes: 7408d3061d2f ("ARM: shmobile: r8a7791: add MLB+ clock") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: r8a7740 dtsi: Add PM domain support
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and hook
it up to the D4 PM domain, so the R-Mobile System Controller driver can
keep the domain powered, until the new Coresight code handles runtime
PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PM / Domains: Add DT bindings for the R-Mobile System Controller
The Renesas R-Mobile System Controller provides a.o. power management
support, following the generic PM domain bindings in
Documentation/devicetree/bindings/power/power_domain.txt.
For now this supports the R-Mobile A1 (r8a7740) only, but it should be
sufficiently generic to handle other members of the SH-Mobile/R-Mobile
family in the future.
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Olof Johansson [Tue, 13 Jan 2015 01:58:19 +0000 (17:58 -0800)]
Merge tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "ARM: berlin: DT changes for v3.20 (round 1)" from Sebastian Hesselbarth:
Berlin DT changes for v3.20 (round 1)
- add PMU nodes for BG2Q and BG2CD
- add PPI CPU masks for TWD timer interrupts
* tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add PPI cpu mask to twd timer interrupts
ARM: dts: berlin: add pmu node for BG2Q and BG2CD
Peter Robinson [Tue, 30 Dec 2014 06:20:27 +0000 (06:20 +0000)]
ARM: dts: Only build dtb if associated Arch and/or SoC is enabled
A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained
definitions whether it be sub ARCH or SOC definitions. The device tree blobs
should only be built if the specific option is enabled that supports that
device or it might be that there's an expectation that the device is supported
when in actual fact it's not. This ensures only the relevant bits are built.
Also standardised the line break between the arch/soc definitions and the
dtbs to be on separate lines for better consistency as per feedback.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Shawn Guo <shawn.guo@freescale.com>
[olof: Fixed stray \ in one of the IMX rules] Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 12 Jan 2015 22:24:07 +0000 (14:24 -0800)]
Merge tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.20" from Simon Horman:
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
* tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: shmobile: r8a7791: add MLB+ clock
ARM: shmobile: r8a7790: add MLB+ clock
ARM: shmobile: ape6evm: Fix LAN9220 VDDVARIO voltage
ARM: shmobile: r8a73a4: Add r8a73a4-ape6evm.dtb to ARCH_SHMOBILE_MULTI
ARM: shmobile: ape6evm: Add keypad to the device tree
ARM: shmobile: ape6evm: Add LEDs to the device tree
ARM: shmobile: ape6evm: synchronize dts with reference platform
ARM: shmobile: ape6evm: fix compatible string for Ethernet controller
ARM: shmobile: r8a7794: Add MMCIF clock to device tree
ARM: shmobile: r8a7794: Add SDHI clocks to device tree
ARM: shmobile: r8a7794: Add I2C clocks to device tree
ARM: shmobile: r8a7779: Add TWD device to DTS
ARM: shmobile: r8a7779: Use MSTP for SCIF clocks
ARM: shmobile: r8a7779: Use R8A7779_CLK_P as SCIF parent clock
ARM: shmobile: r8a7794: Add QSPI clock to device tree
ARM: shmobile: lager: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add SYS-DMAC clocks to device tree
ARM: shmobile: r8a7791: Add IPMMU-SGX clock to device tree
ARM: shmobile: koelsch: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add USBDMAC[01] clocks to device tree
...
Olof Johansson [Mon, 12 Jan 2015 22:22:42 +0000 (14:22 -0800)]
Merge tag 'renesas-dt-cleanups-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Cleanups for v3.20" from Simon Horman:
* Replace status value "ok" with "okay"
* tag 'renesas-dt-cleanups-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference dts: Replace status value "ok" by "okay"
ARM: shmobile: alt dts: Replace status value "ok" by "okay"
ARM: shmobile: koelsch dts: Replace status value "ok" by "okay"
ARM: shmobile: henninger dts: Replace status value "ok" by "okay"
ARM: shmobile: lager dts: Replace status value "ok" by "okay"
ARM: shmobile: armadillo800eva dts: Replace status value "ok" by "okay"
ARM: shmobile: genmai dts: Replace status value "ok" by "okay"