Merge tag 'usb-serial-4.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.18-rc1
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Merge tag 'phy-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.18
*) Add PHY driver for the ATH79 USB PHY
*) Add USB3 PHY driver for Mediatek XS-PHY
*) Add QUSB/QMP V3 USB3 PHY Support for Qualcomm's SDM845
*) Add runtime PM support for mapphone PHY driver
*) Allow phy_pm_runtime_xxx API calls to accept NULL
*) Other minor cleanups and fixes
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Jon Hunter [Wed, 16 May 2018 13:48:55 +0000 (14:48 +0100)]
usb: xhci: tegra: Add support for managing powergates
The Tegra XHCI controller requires that the XUSBA (for superspeed) and
XUSBC (for host) power-domains are enabled. Commit 8df127456f29
("soc/tegra: pmc: Enable XUSB partitions on boot") was added to force
on these power-domains if the XHCI driver is enabled while proper
power-domain support is added, to ensure the device did not hang on
boot. However, rather than forcing on these power-domains in the PMC
driver we can use the legacy Tegra powergate APIs to turn on these
power-domains during the probe of the Tegra XHCI driver.
In the near future we plan to move the Tegra XHCI driver to use the
generic PM domain framework for power-domains and so to prepare for
this only use the legacy Tegra powergate API if there is not PM
domain associated with device (ie. dev.pm_domain is NULL). Please
note that in the future the superspeed and host resets will be handled
by the generic PM domain provider and so these are only these are only
needed in the case where there is no generic PM domain.
Jon Hunter [Wed, 16 May 2018 13:48:54 +0000 (14:48 +0100)]
usb: xhci: tegra: Add runtime PM support
Add runtime PM support to the Tegra XHCI driver and move the function
calls to enable/disable the clocks, regulators and PHY into the runtime
PM callbacks.
Jon Hunter [Wed, 16 May 2018 13:48:53 +0000 (14:48 +0100)]
usb: xhci: tegra: Prepare for adding runtime PM support
When adding runtime PM support to the Tegra XHCI driver, it is desirable
to move the function calls to enable the clocks, regulators and PHY from
the tegra_xusb_probe into the runtime PM handlers. Currently, the
clocks, regulators and PHY are all enabled before we call
usb_create_hcd() in tegra_xusb_probe(), however, we cannot call
pm_runtime_get_sync() at this point because the platform device data is
not yet initialised. Fortunately, the function usb_create_hcd() can be
called before we enable the clocks, regulators and PHY and so prepare
for adding runtime PM support, by moving the call to usb_create_hcd()
before we enable the hardware.
The proposed patch adds compatibility quirks. Because the drive requires two
quirks (one to work with UAS, and another to work with usb-storage), adding this
under unusual_devs.h and not just unusual_uas.h so kernels compiled without UAS
receive the quirk. With the patch, the drive works reliably on UAS and usb-
storage.
(tested on NEC Corporation uPD720200 USB 3.0 host controller).
Signed-off-by: Alexander Kappner <agk@godking.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-storage: Add support for FL_ALWAYS_SYNC flag in the UAS driver
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 24 May 2018 10:49:52 +0000 (13:49 +0300)]
usb: typec: wcove: Remove dependency on HW FSM
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 24 May 2018 08:18:27 +0000 (11:18 +0300)]
usb: roles: intel_xhci: Enable runtime PM
This fixes an issue where the mux does not get configured
when the parent device is suspended. The registers for this
mux are mapped to the parent device MMIO (usually xHCI PCI
device), so in order for the driver to be able to program
the registers, the parent device must be resumed.
Reported-by: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com> Fixes: f6fb9ec02be1 ("usb: roles: Add Intel xHCI USB role switch driver") Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 24 May 2018 08:18:26 +0000 (11:18 +0300)]
usb: typec: fusb302: Fix debugfs issue
Removing the "fusb302" debugfs directory when unloading
the driver. That allows the driver to be loaded more then
one time. The directory will not get actually removed until
it is empty, so only after the last instance has been
removed.
This fixes an issue where the driver can't be re-loaded if
it has been unloaded as the "fusb302" debugfs directory
already exists.
Fixes: 76f0c53d08b9 ("usb: typec: fusb302: Move out of staging") Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver will not probe unless bq24190 is loaded, so
making it a dependency.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Darren Hart <dvhart@infradead.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 24 May 2018 08:18:24 +0000 (11:18 +0300)]
usb: roles: intel_xhci: Always allow user control
Trying to determine the USB port type with this mux is very
difficult. To simplify the situation, always allow user
control, even if the port is USB Type-C port.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Mon, 21 May 2018 12:20:47 +0000 (15:20 +0300)]
usb: typec: Fix htmldocs warning
Fix htmldocs warning:
drivers/usb/typec/mux.c:186: warning: Function parameter or member 'mux' not described in
'typec_mux_unregister'
Reported-by: kbuild test robot <lkp@intel.com> Fixes: bdecb33af34f ("usb: typec: API for controlling USB Type-C Multiplexers") Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
usb: gadget: function: printer: avoid wrong list handling in printer_write()
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Adam Thomson [Tue, 22 May 2018 15:16:24 +0000 (16:16 +0100)]
typec: tcpm: Provide fwnode pointer as part of psy_cfg
For supply registration, provide fwnode pointer of the port device,
via the power_supply_config structure, to allow other psy drivers
to add us as a supplier. At present this only applies to DT
based platforms using the 'power-supplies' DT property, but in the
future should also work for ACPI platforms when the relevant support
is added to the power_supply core.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adam Thomson [Tue, 22 May 2018 15:16:23 +0000 (16:16 +0100)]
power: supply: Add fwnode pointer to power_supply_config struct
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun [Wed, 23 May 2018 08:53:20 +0000 (16:53 +0800)]
usb: mtu3: fix warning of sleep in atomic context in notifier callback
The notifier callbacks of extcon are called in atomic context, but the
callbacks will call regulator_enable()/regulator_disable() which may
sleep caused by mutex, so use work queue to call the sleep functions.
Chunfeng Yun [Wed, 23 May 2018 08:53:15 +0000 (16:53 +0800)]
usb: mtu3: re-enable controller to accept LPM request after LPM resume
After the controller receives a LPM request, it will reject the LPM
request, and need software to re-enable it after LPM resume if the
controller doesn't remote wakeup from L1 automatically
Mathias Nyman [Mon, 21 May 2018 13:40:06 +0000 (16:40 +0300)]
xhci: debugfs: add debugfs interface to enable compliance mode for a port
Enable compliance transition for a port by writing "compliance" to the
ports portsc file in debugfs.
port must be "Not-connected" and Link must be in RxDetect state to enable
compliance mode.
Only needed for host that have CTC flag set.
Allows state transitioning to compliance at 1st LFPS timeout.
Mathias Nyman [Mon, 21 May 2018 13:40:05 +0000 (16:40 +0300)]
xhci: debugfs: add usb ports to xhci debugfs
Add ports/portxx/portsc for each xHC hardware usb port to debugfs.
Showing the content of the port status and control register for
each port (PORTSC)
Portxx is numbered starting from 1 for historical reasons to better
match port numbering shown by lsusb and other places.
Ports in debugfs are in the order XHC controller has them,
In most cases USB2 ports come first, followed by USB3 ports.
i.e. USB2 ports are port01-portxx, and USB3 portxx-portmax.
Mathias Nyman [Mon, 21 May 2018 13:40:02 +0000 (16:40 +0300)]
xhci: xhci-hub: use port structure members instead of xhci_get_ports()
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Mathias Nyman [Mon, 21 May 2018 13:40:01 +0000 (16:40 +0300)]
xhci: use port structures instead of port arrays in xhci.c functions
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Mathias Nyman [Mon, 21 May 2018 13:39:57 +0000 (16:39 +0300)]
xhci: xhci-ring: use port structures for port event handler
use port structures in the port event handler.
Getting the right hcd and hcd portnumber from the hardware port number
is a lot easier with port structures, and allows us to remove a lot
of the previous code, including the find_faked_portnum_from_hw_index()
function
Mathias Nyman [Mon, 21 May 2018 13:39:52 +0000 (16:39 +0300)]
xhci: Create new structures to store xhci port information
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Jianguo Sun [Mon, 21 May 2018 13:39:51 +0000 (16:39 +0300)]
xhci: hisilicon: support HiSilicon STB xHCI host controller
This commit adds support for HiSilicon STB xHCI host controller.
There are two xHCI host controllers on HiSilicon STB SoCs. Each
one requires additional configuration before exposing interface
compliant with xHCI.
Bin Liu [Mon, 21 May 2018 13:42:21 +0000 (08:42 -0500)]
usb: musb: gadget: fix to_musb_request() to not return NULL
The gadget function drivers should ensure the usb_request parameter
passed in is not NULL. UDC core doesn't check if it is NULL, so MUSB
driver shouldn't have to check it either.
Convert to_musb_request() to a simple macro to not directly return NULL
to avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 21 May 2018 13:42:20 +0000 (08:42 -0500)]
USB: musb: dsps: propagate device-tree node
To be able to use DSPS-based controllers with device-tree descriptions
of the USB topology, we need to associate the glue device's device-tree
node with the child controller device.
Note that this can also be used to eventually let USB core manage
generic phys.
Also note that the other glue drivers will require similar changes to be
able to describe their buses in DT.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Mon, 21 May 2018 13:42:13 +0000 (08:42 -0500)]
usb: musb: remove duplicated quirks flag
Both musb_io and musb_platform_ops in struct musb define a quirks flag
for the same purpose. Let's remove the one in struct musb_io, and use
that in struct musb_platform_ops instead.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Mon, 21 May 2018 13:42:09 +0000 (08:42 -0500)]
usb: musb: merge musbhsdma.h into musbhsdma.c
Now Blackfin support is removed, header musbhsdma.h is only included in
musbhsdma.c. So let's merge the content in musbhsdma.h to musbhsdma.c
and delete musbhsdma.h.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 21 May 2018 11:08:44 +0000 (13:08 +0200)]
tty: add missing const to termios hw-change helper
Add missing const qualifiers to the parameters of the termios hw-change
helper, which is used by a few USB serial drivers. This specifically
allows the pl2303 driver to use const arguments in one of its helper as
well.
Johan Hovold [Fri, 18 May 2018 13:25:47 +0000 (15:25 +0200)]
USB: serial: ftdi_sio: fix IXON/IXOFF mixup
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cause double phy_put()
calling. This driver must not call phy_put() in the remove because
the driver calls devm_phy_get() in the probe.
Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy") Cc: <stable@vger.kernel.org> # v4.15+ Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: udc: renesas_usb3: disable the controller's irqs for reconnecting
This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller") Cc: <stable@vger.kernel.org> # v4.5+ Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: udc: renesas_usb3: should fail if devm_phy_get() returns error
This patch fixes an issue that this driver ignores errors other than
the non-existence of the device, f.e. a memory allocation failure
in devm_phy_get(). So, this patch replaces devm_phy_get() with
devm_phy_optional_get().
Reported-by: Simon Horman <horms+renesas@verge.net.au> Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy") Cc: <stable@vger.kernel.org> # v4.15+ Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: udc: renesas_usb3: should call devm_phy_get() before add udc
This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).
Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy") Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: udc: renesas_usb3: should call pm_runtime_enable() before add udc
This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.
Mayank Rana [Fri, 23 Mar 2018 17:05:33 +0000 (10:05 -0700)]
usb: dwc3: gadget: Fix list_del corruption in dwc3_ep_dequeue
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893d4 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tomeu Vizoso [Mon, 26 Mar 2018 09:00:01 +0000 (11:00 +0200)]
usb: dwc2: dwc2_vbus_supply_init: fix error check
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
usb: gadget: f_phonet: fix pn_net_xmit()'s return type
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
John Stultz [Sat, 19 May 2018 00:49:03 +0000 (17:49 -0700)]
usb: dwc2: Fix HiKey regression caused by power_down feature
In 4.17-rc, commit 03ea6d6e9e1f ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com> Cc: Vardan Mikayelyan <mvardan@synopsys.com> Cc: Artur Petrosyan <arturp@synopsys.com> Cc: Grigor Tovmasyan <tovmasya@synopsys.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: linux-usb@vger.kernel.org Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes: 5f0b74e54890 ("USB: dwc3: get extcon device by OF graph bindings") Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Mon, 7 May 2018 12:19:31 +0000 (15:19 +0300)]
usb: dwc3: gadget: init req->{direction,epnum} from alloc_request()
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Wed, 11 Apr 2018 09:58:46 +0000 (12:58 +0300)]
usb: dwc3: gadget: initialize transfer index from send_gadget_ep_cmd()
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Wed, 11 Apr 2018 07:32:52 +0000 (10:32 +0300)]
usb: dwc3: gadget: don't issue End Transfer if we have started reqs
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Wed, 11 Apr 2018 07:31:53 +0000 (10:31 +0300)]
usb: dwc3: debug: decode uFrame from event too
XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Mon, 9 Apr 2018 09:40:48 +0000 (12:40 +0300)]
usb: dwc3: gadget: combine modify & restore into single argument
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>