Olof Johansson [Thu, 16 Jan 2020 18:46:16 +0000 (10:46 -0800)]
Merge tag 'mvebu-dt-5.6-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.6 (part 1)
- Add support for SolidRun Clearfog GTR (Armada 385 based board)
- Move i2c0 to the SoliRrun Microsom dtsi (Armada 38x based)
- Add EEPROM node on SoliRrun Microsom (rev 2.1)
- Add EEPROM node on SoliRrun ClearFog Pro
* tag 'mvebu-dt-5.6-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-388-clearfog: add eeprom
ARM: dts: armada-38x-solidrun-microsom: add eeprom
ARM: armada-38x-solidrun-microsom: move i2c0 to SOM DT
ARM: dts: mvebu: add support for SolidRun Clearfog GTR
Olof Johansson [Thu, 16 Jan 2020 18:43:18 +0000 (10:43 -0800)]
Merge tag 'tegra-for-5.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.6-rc1
These patches do some cleanup to existing nodes, add the memory
subsystem on Tegra186 and Tegra194 as well as the FUSE and APB MISC
nodes on Tegra194. There are also a few additions to the Jetson Nano
device tree to enable additional features and the force recovery
button on the Jetson AGX Xavier now produces a key code that is
actually valid. Finally, an alias is added for the Ethernet card on
Jetson TX2 to allow firmware to find it and pass a MAC address via
device tree.
* tag 'tegra-for-5.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Allow bootloader to configure Ethernet MAC on Jetson TX2
arm64: tegra: Redefine force recovery key on Jetson AGX Xavier
arm64: tegra: Enable SDIO on Jetson Nano M.2 Key E
arm64: tegra: Enable PWM fan on Jetson Nano
arm64: tegra: Add fuse/apbmisc node on Tegra194
arm64: tegra: Make XUSB node consistent with the rest
arm64: tegra: Add the memory subsystem on Tegra194
arm64: tegra: Add external memory controller on Tegra186
arm64: tegra: Add interrupt for memory controller on Tegra186
arm64: tegra: Rename EMC on Tegra132
arm64: tegra: Let the EMC hardware use the EMC clock
Olof Johansson [Thu, 16 Jan 2020 18:42:59 +0000 (10:42 -0800)]
Merge tag 'tegra-for-5.6-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.6-rc1
This adds memory timings for the PAZ100 and does some minor cleanup for
the external memory controller device tree node on Tegra124.
* tag 'tegra-for-5.6-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra20: paz00: Add memory timings
ARM: tegra: Rename EMC on Tegra124
ARM: tegra: Let the EMC hardware use the EMC clock
Olof Johansson [Thu, 16 Jan 2020 18:40:03 +0000 (10:40 -0800)]
Merge tag 'tegra-for-5.6-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.6-rc1
This contains a conversion of the Tegra124 EMC bindings to json-schema
as well as the addition of the bindings for the memory subsystem found
on Tegra186 and Tegra194.
Olof Johansson [Sat, 11 Jan 2020 06:25:56 +0000 (22:25 -0800)]
Merge tag 'samsung-dt-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.6
1. Couple ARM and wcore bus regulators on Exynos542x so higher
frequencies could be used with dynamic voltage and frequency scaling.
Enable this higher frequencies.
2. Correct the polarity of USB3503 hub GPIOs.
3. Adjust the bus frequencies (scaled with devfreq framework) on
Exynos5422 Odroid boards to match values possible to obtain from root
PLLs.
4. Add display to Tiny4412 board.
5. Cleanups and minor improvements.
* tag 'samsung-dt-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Enable FIMD node and add proper panel node to Tiny4412
ARM: dts: samsung: Rename Samsung and Exynos to lowercase
ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids
ARM: dts: exynos: Move Exynos5420 bus related OPPs to the Odroid boards DTS
ARM: dts: exynos: Correct USB3503 GPIOs polarity
ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800
ARM: dts: exynos: Add initial data for coupled regulators for Exynos5422/5800
ARM: dts: exynos: Remove syscon compatible from chipid node on Exynos5
Olof Johansson [Sat, 11 Jan 2020 06:19:00 +0000 (22:19 -0800)]
Merge tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New boards are the Radxa Rock Pi N10 using the VMARC SOM and Dalang
carrier board, separate versions for the two rockpro64 hardware revisions
which switched a pin between revisions. The rockpro64 also got
bluetooth support now.
The px30 got a lot of attention with dsi, gpu and thermal support.
Similarly the rk3399-roc-pc board also got attention with mtd flash,
sdr104 mode, hdmi sound, gpu and a lot of other smaller improvements.
Other than that there is a new gpu-cooling device for rk3399 a cpu
idle-state for rk3328 and more small improvements across a number
of boards.
* tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (37 commits)
arm64: dts: rockchip: Enable mp8859 regulator on rk3399-roc-pc
arm64: dts: rockchip: rk3399-hugsun-x99: remove supports-sd and supports-emmc options
arm64: dts: rockchip: rk3399-firefly: remove num-slots from &sdio0 node
arm64: dts: rockchip: Add PX30 LVDS
arm64: dts: rockchip: add dsi controller for px30
arm64: dts: rockchip: Add PX30 DSI DPHY
arm64: dts: rockchip: Add RK3328 idle state
arm64: dts: rockchip: remove identical &uart0 node from rk3368-lion-haikou
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
ARM: dts: rockchip: Add Radxa Dalang Carrier board
arm64: dts: rockchip: Add VMARC RK3399Pro SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N10 binding
arm64: dts: rockchip: hook up bluetooth at uart0 on rockpro64
arm64: dts: rockchip: enable wifi module at sdio0 on rockpro64
arm64: dts: rockchip: split rk3399-rockpro64 for v2 and v2.1 boards
arm64: dts: rockchip: enable the gpu on px30-evb
arm64: dts: rockchip: add the gpu for px30
dt-bindings: gpu: mali-bifrost: Add Rockchip PX30
arm64: dts: rockchip: Add GPU cooling device for RK3399
arm64: dts: rockchip: Add regulators for PCIe for Radxa Rock Pi 4 board
...
Olof Johansson [Sat, 11 Jan 2020 06:18:33 +0000 (22:18 -0800)]
Merge tag 'v5.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Pin-name corrections for Veyron-Fievel, bluetooth for a number of veyron boards and
additional operating points for rk3288-tinker.
* tag 'v5.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Use ABI name for recovery mode pin on veyron fievel/tiger
ARM: dts: rockchip: Use ABI name for write protect pin on veyron fievel/tiger
ARM: dts: rockchip: Add missing cpu operating points for rk3288-tinker
ARM: dts: rockchip: Add brcm bluetooth for rk3288-veyron
Olof Johansson [Sat, 11 Jan 2020 06:17:22 +0000 (22:17 -0800)]
Merge tag 'stm32-dt-for-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.6, round 1
Highlights:
----------
MPU part:
-Add PWM support on DK2 board.
-Add counter support to STM32 timers.
-Add support of SDMMC 2&3 instances based on "arm,pl18x". SDMMC2 is
connected to eMMC on ED1 board. SDMMC3 is connected to the GPIO
extension connector on EV1 & DKx boards.
-Add ADC support on ED1 board.
-Update devicetree files split to better fit to STM32MP15 SOC & boards
diversity.
-Fix issues seen during YAML validation.
-Enable Ethernet (MAC) TX clock gating during low-power mode.
-Enable USB OTG HS support on DKx boards.
-Enable USB Host EHCI on DKx boards.
MCU part:
-Fix issues seen during YAML validation.
* tag 'stm32-dt-for-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (37 commits)
ARM: dts: stm32: Add power-supply for RGB panel on stm32429i-eval
ARM: dts: stm32: Add power-supply for DSI panel on stm32f469-disco
ARM: dts: stm32: change nvmem node name on stm32mp1
ARM: dts: stm32: change nvmem node name on stm32f429
ARM: dts: stm32: update mlahb node according to the bindings on stm32mp15
ARM: dts: stm32: fix dma controller node name on stm32mp157c
ARM: dts: stm32: fix dma controller node name on stm32f743
ARM: dts: stm32: fix dma controller node name on stm32f746
ARM: dts: stm32: add phy-names to usbotg_hs on stm32mp157c-ev1
ARM: dts: stm32: enable USB OTG HS on stm32mp15 DKx boards
ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp15 DKx
ARM: dts: stm32: enable USBPHYC on stm32mp15 DKx boards
ARM: dts: stm32: remove useless clock-names from RTC node on stm32f746
ARM: dts: stm32: remove useless clock-names from RTC node on stm32f429
ARM: dts: stm32: Enable MAC TX clock gating during TX low-power mode on stm32mp15
ARM: dts: stm32: adjust slew rate for Ethernet on stm32mp15
ARM: dts: stm32: remove syscfg clock on stm32mp15 ethernet
ARM: dts: stm32: remove "@" and "_" from stm32f7 pinmux groups
ARM: dts: stm32: remove "@" and "_" from stm32f4 pinmux groups
ARM: dts: stm32: Adapt STM32MP157C ED1 board to STM32 DT diversity
...
Olof Johansson [Sat, 11 Jan 2020 06:16:17 +0000 (22:16 -0800)]
Merge tag 'hisi-arm64-dt-for-5.6' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.6
- Add remote control map name of the IR device for the hi3798cv200 poplar board
- Correct the PCIe bus range setting for the hi3798cv200
* tag 'hisi-arm64-dt-for-5.6' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi3798cv200: correct PCIe 'bus-range' setting
arm64: dts: hi3798cv200-poplar: add linux,rc-map-name for IR
Olof Johansson [Sat, 11 Jan 2020 06:15:04 +0000 (22:15 -0800)]
Merge tag 'arm-soc/for-5.6/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.6, please pull the following:
- Stephan adds support for the HWRNG on 2711 (Raspberry Pi 4) which is
different than the previous Pi chips
- Florian switches the BCM956265HR board to use the hardware I2C
controllers for interfacing with the SFPs
* tag 'arm-soc/for-5.6/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Enable HWRNG support
ARM: dts: bcm2835: Move rng definition to common location
ARM: dts: NSP: Use hardware I2C for BCM958625HR
Thierry Reding [Fri, 8 Nov 2019 15:36:40 +0000 (16:36 +0100)]
arm64: tegra: Redefine force recovery key on Jetson AGX Xavier
The current BTN_1 code associated with the force-recovery key is not a
valid code for EV_KEY type input devices. This causes errors in the
libinput debug-events command.
There is no system level action that maps to the force-recovery key on
Jetson AGX Xavier, so assign it the KEY_SLEEP action, which at least
makes it do something marginally useful.
Tamás Szűcs [Sun, 8 Dec 2019 19:55:31 +0000 (20:55 +0100)]
arm64: tegra: Enable PWM fan on Jetson Nano
Enable PWM fan and extend CPU thermal zones for monitoring and fan control.
This will trigger the PWM fan on J15 and cool down the system if necessary.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch> Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Wed, 18 Dec 2019 18:59:57 +0000 (21:59 +0300)]
ARM: dts: tegra20: paz00: Add memory timings
PAZ00 board has two variants of DDR2 SDRAM devices for External Memory:
one is Hynix HY5PS1G831CLFP-Y5 and the other is Micron MT47H128M8CF-25:H.
The Micron variant doesn't have official timings in the wild, hence only
timings for the Hynix are added. The memory frequency-scaling was tested
using the Tegra20 devfreq driver.
Tested-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Wed, 18 Dec 2019 09:25:01 +0000 (10:25 +0100)]
arm64: tegra: Make XUSB node consistent with the rest
The ordering of properties in the XUSB node is inconsistent with the
ordering of the properties in other nodes. Resort them to make the node
more consistent. Also get rid of some unnecessary whitespace.
Thierry Reding [Sun, 22 Dec 2019 14:10:35 +0000 (15:10 +0100)]
arm64: tegra: Add the memory subsystem on Tegra194
The memory subsystem on Tegra194 encompasses both the memory and
external memory controllers. The EMC is represented as a subnode of the
MC and a ranges property is used to describe the register ranges.
A dma-ranges property is also added to describe that all memory clients
can address up to 39 bits using the memory controller client interface
(MCCIF), unless otherwise limited by the DMA engines of the hardware. A
memory client can technically use 40 bits of addresses, but the memory
controller on Tegra194 uses bit 39 to determine the XBAR format used to
access memory. Use of this bit needs to be explicitly controlled by the
operating system drivers for devices that can use this on-the-fly format
conversion. Using the dma-ranges property prevents the operating system
from using the bit implicitly, for example in I/O virtual address
mappings.
Thierry Reding [Sun, 22 Dec 2019 14:10:34 +0000 (15:10 +0100)]
arm64: tegra: Add external memory controller on Tegra186
Add the external memory controller as a child device of the memory
controller on Tegra186. The memory controller really represents the
memory subsystem that encompasses both the memory and external memory
controllers. The external memory controller uses the BPMP to obtain the
list of supported EMC frequencies and set the EMC frequency.
Also set up the dma-ranges property to describe that all memory clients
can address up to 40 bits using the memory controller client interface
(MCCIF), unless otherwise limited by the DMA engines of the hardware.
The NVIDIA Tegra186 SoC contains a memory subsystem composed of the
memory controller and the external memory controller. The memory
controller provides interfaces for the memory clients to access the
memory. Accesses can be either bounced through the SMMU for IOVA
translation or directly to the EMC.
The bulk of the programming of the external memory controller happens
through interfaces exposed by the BPMP. Describe this relationship by
adding a phandle reference to the BPMP to the EMC node.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Rob Herring <robh@kernel.org>
This header contains definitions for the memory controller found on
NVIDIA Tegra194 SoCs, such as the stream IDs used for the ARM SMMU and
the IDs used to identify the various memory clients.
Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Rob Herring <robh@kernel.org>
Thierry Reding [Sun, 22 Dec 2019 11:39:19 +0000 (12:39 +0100)]
arm64: tegra: Let the EMC hardware use the EMC clock
The EMC hardware block needs access to the EMC clock in order to scale
the external memory frequency. Add the clocks property so that drivers
for the EMC can acquire a reference to the EMC clock.
Thierry Reding [Sun, 22 Dec 2019 11:39:18 +0000 (12:39 +0100)]
ARM: tegra: Let the EMC hardware use the EMC clock
The EMC hardware block needs access to the EMC clock in order to scale
the external memory frequency. Add the clocks property so that drivers
for the EMC can acquire a reference to the EMC clock.
Thierry Reding [Sun, 22 Dec 2019 11:39:16 +0000 (12:39 +0100)]
dt-bindings: memory-controller: Convert Tegra124 EMC to json-schema
Convert the device tree bindings for the Tegra124 EMC controller to the
DT schema format using json-schema. While at it, clean up the binding a
little bit by removing any mention of how RAM code and clock frequency
are represented in unit-addresses (which they aren't) and by adding the
EMC clock without which the EMC controller can't change the frequency at
which the external memory is clocked. While this is technically an ABI
break (the clock was not required before), this should be fine because
there isn't much that the EMC driver can do without access to the EMC
clock.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Rob Herring <robh@kernel.org>
Amelie Delaunay [Mon, 9 Dec 2019 14:17:26 +0000 (15:17 +0100)]
ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp15 DKx
This patch enables USB Host (USBH) EHCI controller on stm32mp15 dk boards.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Amelie Delaunay [Mon, 9 Dec 2019 14:15:09 +0000 (15:15 +0100)]
ARM: dts: stm32: enable USBPHYC on stm32mp15 DKx boards
This patch enables USBPHYC (USB PHY Controller on stm32mp15 DKx boards.
This enables the two usbphyc usb2 ports, which require 3 supplies:
3v3, 1v1 and 1v8.
Markus Reichl [Mon, 6 Jan 2020 21:16:28 +0000 (22:16 +0100)]
arm64: dts: rockchip: Enable mp8859 regulator on rk3399-roc-pc
The rk3399-roc-pc uses a MP8859 DC/DC converter for 12V supply.
This supplies 5V only in default state after booting.
Now we can control the output voltage via I2C interface.
Add a node for the driver to reach 12V.
ARM: dts: rockchip: Use ABI name for recovery mode pin on veyron fievel/tiger
The recovery mode pin is currently named 'REC_MODE_L', which is
how the signal is called in the schematics. The Chrome OS ABI
requires the pin to be named 'RECOVERY_SW_L', which is also how
it is called on all other veyron devices. Rename the pin to match
the ABI.
Baruch Siach [Thu, 19 Dec 2019 10:28:45 +0000 (12:28 +0200)]
arm64: dts: marvell: clearfog-gt-8k: fix switch cpu port node
Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.
Fixes: a6120833272c ("arm64: dts: add support for SolidRun Clearfog GT 8K") Reported-by: Denis Odintsov <d.odintsov@traviangames.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Baruch Siach [Sun, 5 Jan 2020 15:38:37 +0000 (17:38 +0200)]
ARM: dts: mvebu: add support for SolidRun Clearfog GTR
SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They
features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port,
1 directly connected SFP port, 1 SFP port behind the switch (not
currently described in DT), 3 mini-PCIe slots, eMMC, SPI flash, USB3
port.
ARM: dts: rockchip: Use ABI name for write protect pin on veyron fievel/tiger
The flash write protect pin is currently named 'FW_WP_AP', which is
how the signal is called in the schematics. The Chrome OS ABI
requires the pin to be named 'AP_FLASH_WP_L', which is also how
it is called on all other veyron devices. Rename the pin to match
the ABI.
ARM: dts: samsung: Rename Samsung and Exynos to lowercase
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Olof Johansson [Tue, 7 Jan 2020 19:25:28 +0000 (11:25 -0800)]
Merge tag 'omap-for-v5.6/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop more legacy platform data for omaps for v5.6 merge window
We can now probe devices with ti-sysc interconnect driver and dts
data, and can continue dropping the related platform data and custom
ti,hwmods dts property for various devices.
And related to that, we finally can remove the legacy sdma support in
favor of using the dmaengine driver only. I was planning to send the
sdma changes separately, but that would have produced a pile of
pointless merge conflicts, so I decided it's best to resolve it locally.
After all, the sdma series also ends up removing the related platform
data.
Note that this series is based on omap-for-v5.6/ti-sysc-dt-signed branch
as it depends for dts data being in place.
* tag 'omap-for-v5.6/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (56 commits)
ARM: OMAP2+: Drop legacy platform data for sdma
ARM: OMAP2+: Drop legacy init for sdma
dmaengine: ti: omap-dma: Use cpu notifier to block idle for omap2
dmaengine: ti: omap-dma: Allocate channels directly
dmaengine: ti: omap-dma: Pass sdma auxdata to driver and use it
dmaengine: ti: omap-dma: Configure global priority register directly
ARM: OMAP5: hwmod-data: remove OMAP5 IOMMU hwmod data
ARM: OMAP4: hwmod-data: remove OMAP4 IOMMU hwmod data
ARM: OMAP2+: Drop legacy platform data for omap4 fdif
ARM: OMAP2+: Drop legacy platform data for omap4 slimbus
ARM: OMAP2+: Drop legacy platform data for omap5 kbd
ARM: OMAP2+: Drop legacy platform data for omap4 kbd
ARM: OMAP2+: Drop legacy platform data for dra7 smartreflex
ARM: OMAP2+: Drop legacy platform data for omap4 smartreflex
ARM: OMAP2+: Drop legacy platform data for omap4 hsi
ARM: OMAP2+: Drop legacy platform data for am4 vpfe
ARM: OMAP2+: Drop legacy platform data for dra7 ocp2scp
ARM: OMAP2+: Drop legacy platform data for omap5 ocp2scp
ARM: OMAP2+: Drop legacy platform data for omap4 ocp2scp
ARM: OMAP2+: Drop legacy platform data for am4 ocp2scp
...
Olof Johansson [Tue, 7 Jan 2020 19:16:23 +0000 (11:16 -0800)]
Merge tag 'omap-for-v5.6/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.6 merge window
Devicetree changes for omaps for v5.6 to configure more
devices and update boards to use generic lcd panels:
- Configure HDMI for dra76-evm and am57xx-idk
- Correct node name for am3517 mdio
- Convert am335x-evm, am335x-evmsk, and am335x-icev2 to use generic
panels
* tag 'omap-for-v5.6/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
ARM: dts: am335x-evmsk: Use drm simple-panel instead of tilcdc-panel
ARM: dts: am335x-evm: Use drm simple-panel instead of tilcdc-panel
ARM: dts: omap3: name mdio node properly
ARM: dts: am57xx-idk-common: add HDMI to the common dtsi
ARM: dts: dra76-evm: add HDMI output
Stephen Brennan [Wed, 20 Nov 2019 03:16:21 +0000 (19:16 -0800)]
ARM: dts: bcm2835: Move rng definition to common location
BCM2711 inherits from BCM283X, but has an incompatible HWRNG. Move this
node to bcm2835-common.dtsi, so that BCM2711 can define its own.
Signed-off-by: Stephen Brennan <stephen@brennan.io> Acked-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Lubomir Rintel [Fri, 20 Dec 2019 06:53:14 +0000 (07:53 +0100)]
ARM: dts: mmp3-dell-ariel: Enable the HSIC
There's a SMSC USB2640 (USB hub & SD controller) connected to it, but
the SD card slot footprint is unpopulated. Also connected to the hub is
a SMSC LAN7500 gigabit ethernet adapter.
Lubomir Rintel [Fri, 20 Dec 2019 06:53:13 +0000 (07:53 +0100)]
ARM: dts: mmp3: Add HSIC controllers
There are two on MMP3, along with the PHYs. The PHYs are made compatible
with the NOP transceiver, since there's no driver for the time being and
they're likely configured by the firmware.
Olof Johansson [Mon, 6 Jan 2020 17:28:56 +0000 (09:28 -0800)]
Merge tag 'renesas-arm64-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.6
- Remove now unused ARCH_R8A7796 config symbol,
- Rename R-Car H3 and M3-W SoC, and ULCB board DTS files to increase
naming consistency,
- Miscellaneous fixes for issues detected by "make dtbs_check",
- Enhance support for R-Car M3-W+,
- Display support for the EK874 board,
- Prepare for split of R-Car H3 ES1.x and ES2.0+ config symbols,
- Minor fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: Prepare for split of ARCH_R8A7795 into ARCH_R8A7795[01]
arm64: dts: renesas: Sort DTBs in Makefile
arm64: dts: renesas: Drop redundant SoC prefixes from ULCB DTS file names
arm64: dts: renesas: Rename r8a7795{-es1,}* to r8a7795[01]*
arm64: dts: renesas: Add EK874 board with idk-2121wr display support
arm64: dts: renesas: r8a77961: Add SDHI nodes
arm64: dts: renesas: r8a77961: Add I2C nodes
arm64: dts: renesas: r8a77961: Add SYS-DMAC nodes
arm64: dts: renesas: r8a77961: Add RAVB node
arm64: dts: renesas: r8a77961: Add GPIO nodes
arm64: dts: renesas: r8a77961: Add RWDT node
arm64: dts: renesas: r8a77990: ebisu: Remove clkout-lr-synchronous from sound
arm64: dts: renesas: r8a77970: Group tuples in thermal reg property
arm64: dts: renesas: Group tuples in pci ranges and dma-ranges properties
arm64: dts: renesas: Group tuples in interrupt properties
arm64: dts: renesas: Group tuples in regulator-gpio states properties
arm64: dts: renesas: Rename r8a7796* to r8a77960*
arm64: dts: renesas: Remove use of ARCH_R8A7796
Olof Johansson [Mon, 6 Jan 2020 17:28:00 +0000 (09:28 -0800)]
Merge tag 'renesas-arm-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.6
- Touch screen support for the iwg20d board,
- ARM global timer support on Cortex-A9 MPCore SoCs,
- Miscellaneous fixes for issues detected by "make dtbs_check".
* tag 'renesas-arm-dt-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: sh73a0: Add missing clock-frequency for fixed clocks
ARM: dts: r8a7778: Add missing clock-frequency for fixed clocks
ARM: dts: rcar-gen2: Add missing mmio-sram bus properties
ARM: dts: rcar-gen2: Fix PCI high address in interrupt-map-mask
ARM: dts: renesas: Group tuples in pci ranges and dma-ranges properties
ARM: dts: renesas: Group tuples in interrupt properties
ARM: dts: renesas: Group tuples in regulator-gpio states properties
ARM: dts: r8a7779: Add device node for ARM global timer
ARM: dts: sh73a0: Add device node for ARM global timer
ARM: dts: sh73a0: Rename twd clock to periph clock
ARM: dts: iwg20d-q7-common: Add LCD support
Olof Johansson [Mon, 6 Jan 2020 17:22:26 +0000 (09:22 -0800)]
Merge tag 'ux500-armsoc-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
Support the Samsung GT-I8190/Golden phone:
- Proper include file for the AB8505 PMIC variant.
- Add a DTS file for the GT-I8190/Golden
- Extend the IMU, touch screen, WiFi and Bluetooth
as separate patches.
* tag 'ux500-armsoc-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500: samsung-golden: Add Bluetooth
ARM: dts: ux500: samsung-golden: Add WiFi
ARM: dts: ux500: samsung-golden: Add touch screen
ARM: dts: ux500: samsung-golden: Add IMU (accelerometer + gyroscope)
ARM: dts: ux500: Add device tree for Samsung Galaxy S III mini (GT-I8190)
dt-bindings: arm: ux500: Document samsung,golden compatible
ARM: dts: ux500: Add device tree include for AB8505
ARM: dts: ux500: Remove unused ste-href-ab8505.dtsi
Robin Murphy [Sun, 29 Dec 2019 20:16:17 +0000 (20:16 +0000)]
arm64: dts: rockchip: Add RK3328 idle state
Downstream RK3328 DTBs describe a CPU idle state matching that present
on other SoCs like RK3399. This works with upstream Trusted Firmware-A
too, so let's add it here.
ARM: dts: sh73a0: Add missing clock-frequency for fixed clocks
"clock-frequency" is a required property for devices nodes compatible
with "fixed-clock", leading to warnings when running
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/fixed-clock.yaml
arch/arm/boot/dts/sh73a0-kzm9g.dt.yaml: extcki: 'clock-frequency' is a required property
Fix this by adding the missing "clock-frequency" properties to the various
clocks, to be overridden by the board DTS files when populated.
ARM: dts: r8a7778: Add missing clock-frequency for fixed clocks
"clock-frequency" is a required property for devices nodes compatible
with "fixed-clock", leading to warnings when running
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/fixed-clock.yaml
arch/arm/boot/dts/r8a7778-bockw.dt.yaml: audio_clk_a: 'clock-frequency' is a required property
arch/arm/boot/dts/r8a7778-bockw.dt.yaml: audio_clk_b: 'clock-frequency' is a required property
arch/arm/boot/dts/r8a7778-bockw.dt.yaml: audio_clk_c: 'clock-frequency' is a required property
Fix this by adding the missing "clock-frequency" properties to the audio
clocks, to be overridden by board DTS files when populated.
ARM: dts: rcar-gen2: Add missing mmio-sram bus properties
"#address-cells", "#size-cells", and "ranges" are required properties
for devices nodes compatible with "mmio-sram", leading to warnings when
running "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#address-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#size-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: 'ranges' is a required property
...
Fix this by adding the missing properties to the mmio-sram device nodes
in the DTS files for all affected R-Car Gen2 and RZ/G1 SoCs.
ARM: dts: rcar-gen2: Fix PCI high address in interrupt-map-mask
"make dtbs_check" emits warnings like:
pci@ee090000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
pci@ee0b0000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
pci@ee0d0000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
According to dt-schemas/schemas/pci/pci-bus.yaml, the PCI high address
cell value in the "interrupt-map-mask" property must lie in the range
0..0xf800.
Fix this by correcting the values from 0xff00 to 0xf800 in all affected
R-Car Gen2 and RZ/G1 DTS files.
arm64: dts: renesas: Prepare for split of ARCH_R8A7795 into ARCH_R8A7795[01]
As R-Car H3 ES1.x (R8A77950) and R-Car H3 ES2.0+ (R8A77951) are really
different SoCs, CONFIG_ARCH_R8A7795 will be split in
CONFIG_ARCH_R8A77950 and CONFIG_ARCH_R8A77951.
Relax dependencies by handling both the old and the new symbols.
Sort the entries for the various DTBs in the Makefile by SoC and board
type. Keep Salvator-X(S) together, and do the same for ULCB with and
without Kingfisher extension.
arm64: dts: renesas: Drop redundant SoC prefixes from ULCB DTS file names
Unlike the V3MSK and V3HSK boards, the various "ULCB" boards are really
the same boards, with different SiPs fitted, just like the Salvator-X(S)
boards. Furthermore, the "H3", "M3", and "M3N" prefixes of the "ULCB"
parts in the DTS file names are redundant, as they are implied by the
SoC part numbers, which are also part of the file names.
Hence drop the redundant prefixes, to make the DTS file names consistent
with the file names for the various "Salvator-X(S)" boards.
arm64: dts: renesas: Rename r8a7795{-es1,}* to r8a7795[01]*
Despite using the same compatible values ("r8a7795"-based) because of
historical reasons, R-Car H3 ES1.x (R8A77950) and R-Car H3 ES2.0+
(R8A77951) are really different SoCs, with different part numbers.
Reflect this in the DTS files by changing their base names from
"r8a7795-es1" and "r8a7795" to "r8a77950" resp. "r8a77951".
Drop all "ES" references next to part numbers, as they are implied by
the part numbers, and thus redundant.
Note that DT binding headers, definitions, and compatible values are
not renamed, to preserve backward compatibility.
Tony Lindgren [Tue, 10 Dec 2019 16:10:31 +0000 (08:10 -0800)]
ARM: OMAP2+: Drop legacy platform data for sdma
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Vinod Koul <vkoul@kernel.org> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 16 Dec 2019 22:41:53 +0000 (14:41 -0800)]
ARM: OMAP2+: Drop legacy init for sdma
We can now drop legacy init for sdma as we pass the quirks in auxdata to
the dmaengine driver.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Vinod Koul <vkoul@kernel.org> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Stephan Gerhold [Thu, 19 Dec 2019 20:20:51 +0000 (21:20 +0100)]
ARM: dts: ux500: samsung-golden: Add Bluetooth
samsung-golden uses a BCM4334 WiFi+BT combo chip.
The BT part is connected via UART and supported by the hci_bcm
driver in mainline.
Add the necessary device tree changes to make it load correctly.
It requires (seemingly) device-specific firmware that can be
extracted from the stock Android system used on samsung-golden:
- /system/bin/bcm4334.hcd -> /lib/firmware/brcm/BCM4334B0.hcd
On my device, scanning for other Bluetooth devices works just fine,
but for some reason it keeps disconnecting immediately
when attempting to connect to an other device.
Stephan Gerhold [Thu, 19 Dec 2019 20:20:50 +0000 (21:20 +0100)]
ARM: dts: ux500: samsung-golden: Add WiFi
samsung-golden uses a BCM4334 WiFi+BT combo chip, connected to SDIO.
It is supported by the brcmfmac driver in mainline,
so we only need to set up the device tree to make it work correctly.
Note: brcmfmac requires (proprietary) firmware + a device-specific
NVRAM file. Both can be extracted from the stock Android system
used on samsung-golden:
- /system/etc/wifi/bcmdhd_sta.bin_b2 -> /lib/firmware/brcm/brcmfmac4334-sdio.bin
- /system/etc/wifi/nvram_net.txt_GPIO4 -> /lib/firmware/brcm/brcmfmac4334-sdio.samsung,golden.txt
brcmfmac4334-sdio.bin from linux-firmware also seems to work,
but results in occasional errors for some reason.