net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
This driver becomes the first user of the kernel's `ETHTOOL_PHY_EDPD`
phy-tunable feature.
EDPD is also enabled by default on PHY config_init, but can be disabled via
the phy-tunable control.
When enabling EDPD, it's also a good idea (for the ADIN PHYs) to enable TX
periodic pulses, so that in case the other PHY is also on EDPD mode, there
is no lock-up situation where both sides are waiting for the other to
transmit.
Via the phy-tunable control, TX pulses can be disabled if specifying 0
`tx-interval` via ethtool.
The ADIN PHY supports only fixed 1 second intervals; they cannot be
configured. That is why the acceptable values are 1,
ETHTOOL_PHY_EDPD_DFLT_TX_MSECS and ETHTOOL_PHY_EDPD_NO_TX (which disables
TX pulses).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool: implement Energy Detect Powerdown support via phy-tunable
The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like
this feature is common across other PHYs (like EEE), and defining
`ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long.
The way EDPD works, is that the RX block is put to a lower power mode,
except for link-pulse detection circuits. The TX block is also put to low
power mode, but the PHY wakes-up periodically to send link pulses, to avoid
lock-ups in case the other side is also in EDPD mode.
Currently, there are 2 PHY drivers that look like they could use this new
PHY tunable feature: the `adin` && `micrel` PHYs.
The ADIN's datasheet mentions that TX pulses are at intervals of 1 second
default each, and they can be disabled. For the Micrel KSZ9031 PHY, the
datasheet does not mention whether they can be disabled, but mentions that
they can modified.
The way this change is structured, is similar to the PHY tunable downshift
control:
* a `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` value is exposed to cover a default
TX interval; some PHYs could specify a certain value that makes sense
* `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled
* `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD
As noted by the `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` the interval unit is 1
millisecond, which should cover a reasonable range of intervals:
- from 1 millisecond, which does not sound like much of a power-saver
- to ~65 seconds which is quite a lot to wait for a link to come up when
plugging a cable
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xen-netfront: do not assume sk_buff_head list is empty in error handling
When skb_shinfo(skb) is not able to cache extra fragment (that is,
skb_shinfo(skb)->nr_frags >= MAX_SKB_FRAGS), xennet_fill_frags() assumes
the sk_buff_head list is already empty. As a result, cons is increased only
by 1 and returns to error handling path in xennet_poll().
However, if the sk_buff_head list is not empty, queue->rx.rsp_cons may be
set incorrectly. That is, queue->rx.rsp_cons would point to the rx ring
buffer entries whose queue->rx_skbs[i] and queue->grant_rx_ref[i] are
already cleared to NULL. This leads to NULL pointer access in the next
iteration to process rx ring buffer entries.
Below is how xennet_poll() does error handling. All remaining entries in
tmpq are accounted to queue->rx.rsp_cons without assuming how many
outstanding skbs are remained in the list.
985 static int xennet_poll(struct napi_struct *napi, int budget)
... ...
1032 if (unlikely(xennet_set_skb_gso(skb, gso))) {
1033 __skb_queue_head(&tmpq, skb);
1034 queue->rx.rsp_cons += skb_queue_len(&tmpq);
1035 goto err;
1036 }
It is better to always have the error handling in the same way.
Fixes: ad4f15dc2c70 ("xen/netfront: don't bug in case of too many frags") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Sun, 15 Sep 2019 17:21:05 +0000 (19:21 +0200)]
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition that can occur when calling ena_down().
The ena_clean_tx_irq() - which is a part of the napi handler -
function might wake up the tx queue when the queue is supposed
to be down (during recovery or changing the size of the queues
for example) This causes the ena_start_xmit() function to trigger
and possibly try to access the destroyed queues.
When working in 'packet' mode, drop monitor generates a notification
with a potentially truncated payload of the dropped packet. The payload
is copied from the MAC header, but I forgot to check that the MAC header
was set, so do it now.
Patch #1 sets the offsets to the various protocol layers in netdevsim,
so that it will continue to work after the MAC header check is added to
drop monitor in patch #2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in 'packet' mode, drop monitor generates a notification
with a potentially truncated payload of the dropped packet. The payload
is copied from the MAC header, but I forgot to check that the MAC header
was set, so do it now.
Fixes: ca30707dee2b ("drop_monitor: Add packet alert mode") Fixes: 5e58109b1ea4 ("drop_monitor: Add support for packet alert mode for hardware drops") Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Sep 2019 19:32:58 +0000 (21:32 +0200)]
Merge branch 'tc-taprio-offload-for-SJA1105-DSA'
Vladimir Oltean says:
====================
tc-taprio offload for SJA1105 DSA
This is the third attempt to submit the tc-taprio offload model for
inclusion in the networking tree. The sja1105 switch driver will provide
the first implementation of the offload. Only the bare minimum is added:
- The offload model and a DSA pass-through
- The hardware implementation
- The interaction with the netdev queues in the tagger code
- Documentation
What has been removed from previous attempts is support for
PTP-as-clocksource in sja1105, as well as configuring the traffic class
for management traffic. These will be added as soon as the offload
model is settled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 15 Sep 2019 02:00:02 +0000 (05:00 +0300)]
net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload
This qdisc offload is the closest thing to what the SJA1105 supports in
hardware for time-based egress shaping. The switch core really is built
around SAE AS6802/TTEthernet (a TTTech standard) but can be made to
operate similarly to IEEE 802.1Qbv with some constraints:
- The gate control list is a global list for all ports. There are 8
execution threads that iterate through this global list in parallel.
I don't know why 8, there are only 4 front-panel ports.
- Care must be taken by the user to make sure that two execution threads
never get to execute a GCL entry simultaneously. I created a O(n^4)
checker for this hardware limitation, prior to accepting a taprio
offload configuration as valid.
- The spec says that if a GCL entry's interval is shorter than the frame
length, you shouldn't send it (and end up in head-of-line blocking).
Well, this switch does anyway.
- The switch has no concept of ADMIN and OPER configurations. Because
it's so simple, the TAS settings are loaded through the static config
tables interface, so there isn't even place for any discussion about
'graceful switchover between ADMIN and OPER'. You just reset the
switch and upload a new OPER config.
- The switch accepts multiple time sources for the gate events. Right
now I am using the standalone clock source as opposed to PTP. So the
base time parameter doesn't really do much. Support for the PTP clock
source will be added in a future series.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 15 Sep 2019 02:00:01 +0000 (05:00 +0300)]
net: dsa: sja1105: Advertise the 8 TX queues
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 15 Sep 2019 01:59:59 +0000 (04:59 +0300)]
net: dsa: Pass ndo_setup_tc slave callback to drivers
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This allows taprio to offload the schedule enforcement to capable
network cards, resulting in more precise windows and less CPU usage.
The gate mask acts on traffic classes (groups of queues of same
priority), as specified in IEEE 802.1Q-2018, and following the existing
taprio and mqprio semantics.
It is up to the driver to perform conversion between tc and individual
netdev queues if for some reason it needs to make that distinction.
Full offload is requested from the network interface by specifying
"flags 2" in the tc qdisc creation command, which in turn corresponds to
the TCA_TAPRIO_ATTR_FLAG_FULL_OFFLOAD bit.
The important detail here is the clockid which is implicitly /dev/ptpN
for full offload, and hence not configurable.
A reference counting API is added to support the use case where Ethernet
drivers need to keep the taprio offload structure locally (i.e. they are
a multi-port switch driver, and configuring a port depends on the
settings of other ports as well). The refcount_t variable is kept in a
private structure (__tc_taprio_qopt_offload) and not exposed to drivers.
In the future, the private structure might also be expanded with a
backpointer to taprio_sched *q, to implement the notification system
described in the patch (of when admin became oper, or an error occurred,
etc, so the offload can be monitored with 'tc qdisc show').
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'core-process-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd/waitid updates from Christian Brauner:
"This contains two features and various tests.
First, it adds support for waiting on process through pidfds by adding
the P_PIDFD type to the waitid() syscall. This completes the basic
functionality of the pidfd api (cf. [1]). In the meantime we also have
a new adition to the userspace projects that make use of the pidfd
api. The qt project was nice enough to send a mail pointing out that
they have a pr up to switch to the pidfd api (cf. [2]).
Second, this tag contains an extension to the waitid() syscall to make
it possible to wait on the current process group in a race free manner
(even though the actual problem is very unlikely) by specifing 0
together with the P_PGID type. This extension traces back to a
discussion on the glibc development mailing list.
There are also a range of tests for the features above. Additionally,
the test-suite which detected the pidfd-polling race we fixed in [3]
is included in this tag"
[1] https://lwn.net/Articles/794707/
[2] https://codereview.qt-project.org/c/qt/qtbase/+/108456
[3] commit b191d6491be6 ("pidfd: fix a poll race when setting exit_state")
* tag 'core-process-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
waitid: Add support for waiting for the current process group
tests: add pidfd poll tests
tests: move common definitions and functions into pidfd.h
pidfd: add pidfd_wait tests
pidfd: add P_PIDFD to waitid()
Russell King [Sat, 14 Sep 2019 09:44:04 +0000 (10:44 +0100)]
net: phylink: clarify where phylink should be used
Update the phylink documentation to make it clear that phylink is
designed to be used on the MAC facing side of the link, rather than
between a SFP and PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patchset for the recently added health and error recovery
feature. The first fix is to prevent .ndo_set_rx_mode() from proceeding
when reset is in progress. The 2nd fix is for the firmware coredump
command. The 3rd and 4th patches update the error recovery process
slightly to add a state that polls and waits for the firmware to be down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Add a new BNXT_FW_RESET_STATE_POLL_FW_DOWN state.
This new state is required when firmware indicates that the error
recovery process requires polling for firmware state to be completely
down before initiating reset. For example, firmware may take some
time to collect the crash dump before it is down and ready to be
reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Increase timeout for HWRM_DBG_COREDUMP_XX commands
Firmware coredump messages take much longer than standard messages,
so increase the timeout accordingly.
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 14 Sep 2019 04:01:38 +0000 (00:01 -0400)]
bnxt_en: Don't proceed in .ndo_set_rx_mode() when device is not in open state.
Check the BNXT_STATE_OPEN flag instead of netif_running() in
bnxt_set_rx_mode(). If the driver is going through any reset, such
as firmware reset or even TX timeout, it may not be ready to set the RX
mode and may crash. The new rx mode settings will be picked up when
the device is opened again later.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
André Almeida [Mon, 16 Sep 2019 14:07:58 +0000 (11:07 -0300)]
null_blk: match the type of parameter nr_devices
Since the variable nr_devices is an unsigned int, the module_param()
should also use this type. Change the type so they can match.
Fixes: f7c4ce890dd2 ("null_blk: validate the number of devices") Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: André Almeida <andrealmeid@collabora.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
André Almeida [Mon, 16 Sep 2019 14:07:57 +0000 (11:07 -0300)]
null_blk: do not fail the module load with zero devices
The module load should fail only if there is something wrong with the
configuration or if an error prevents it to work properly. The module
should be able to be loaded with (nr_device == 0), since it will not
trigger errors or be in malfunction state. Preventing loading with zero
devices also breaks applications that configures this module using
configfs API. Remove the nr_device check to fix this.
Fixes: f7c4ce890dd2 ("null_blk: validate the number of devices") Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: André Almeida <andrealmeid@collabora.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Thomas Higdon [Fri, 13 Sep 2019 23:23:35 +0000 (23:23 +0000)]
tcp: Add snd_wnd to TCP_INFO
Neal Cardwell mentioned that snd_wnd would be useful for diagnosing TCP
performance problems --
> (1) Usually when we're diagnosing TCP performance problems, we do so
> from the sender, since the sender makes most of the
> performance-critical decisions (cwnd, pacing, TSO size, TSQ, etc).
> From the sender-side the thing that would be most useful is to see
> tp->snd_wnd, the receive window that the receiver has advertised to
> the sender.
This serves the purpose of adding an additional __u32 to avoid the
would-be hole caused by the addition of the tcpi_rcvi_ooopack field.
Signed-off-by: Thomas Higdon <tph@fb.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Higdon [Fri, 13 Sep 2019 23:23:34 +0000 (23:23 +0000)]
tcp: Add TCP_INFO counter for packets received out-of-order
For receive-heavy cases on the server-side, we want to track the
connection quality for individual client IPs. This counter, similar to
the existing system-wide TCPOFOQueue counter in /proc/net/netstat,
tracks out-of-order packet reception. By providing this counter in
TCP_INFO, it will allow understanding to what degree receive-heavy
sockets are experiencing out-of-order delivery and packet drops
indicating congestion.
Please note that this is similar to the counter in NetBSD TCP_INFO, and
has the same name.
Also note that we avoid increasing the size of the tcp_sock struct by
taking advantage of a hole.
Signed-off-by: Thomas Higdon <tph@fb.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO device reset line is optional and now that gpiod_get_optional()
returns proper value when GPIO support is compiled out, there is no
reason to use fwnode_get_named_gpiod() that I plan to hide away.
Let's switch to using more standard gpiod_get_optional() and
gpiod_set_consumer_name() to keep the nice "PHY reset" label.
Also there is no reason to only try to fetch the reset GPIO when we have
OF node, gpiolib can fetch GPIO data from firmwares as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Now that initial BPF backend for gcc has been merged upstream, enable
BPF kselftest suite for bpf-gcc. Also fix a BE issue with access to
bpf_sysctl.file_pos, from Ilya.
2) Follow-up fix for link-vmlinux.sh to remove bash-specific extensions
related to recent work on exposing BTF info through sysfs, from Andrii.
3) AF_XDP zero copy fixes for i40e and ixgbe driver which caused umem
headroom to be added twice, from Ciara.
4) Refactoring work to convert sock opt tests into test_progs framework
in BPF kselftests, from Stanislav.
5) Fix a general protection fault in dev_map_hash_update_elem(), from Toke.
6) Cleanup to use BPF_PROG_RUN() macro in KCM, from Sami.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Ott [Tue, 10 Sep 2019 13:45:04 +0000 (15:45 +0200)]
s390/pci: fix MSI message data
After recent changes the MSI message data needs to specify the
function-relative IRQ number.
Reported-and-tested-by: Alexander Schmidt <alexs@linux.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Ilya Leoshkevich [Fri, 16 Aug 2019 10:53:00 +0000 (12:53 +0200)]
bpf: fix accessing bpf_sysctl.file_pos on s390
"ctx:file_pos sysctl:read write ok" fails on s390 with "Read value !=
nux". This is because verifier rewrites a complete 32-bit
bpf_sysctl.file_pos update to a partial update of the first 32 bits of
64-bit *bpf_sysctl_kern.ppos, which is not correct on big-endian
systems.
Fix by using an offset on big-endian systems.
Ditto for bpf_sysctl.file_pos reads. Currently the test does not detect
a problem there, since it expects to see 0, which it gets with high
probability in error cases, so change it to seek to offset 3 and expect
3 in bpf_sysctl.file_pos.
Fixes: e1550bfe0de4 ("bpf: Add file_pos field to bpf_sysctl ctx") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20190816105300.49035-1-iii@linux.ibm.com/
xdp: Fix race in dev_map_hash_update_elem() when replacing element
syzbot found a crash in dev_map_hash_update_elem(), when replacing an
element with a new one. Jesper correctly identified the cause of the crash
as a race condition between the initial lookup in the map (which is done
before taking the lock), and the removal of the old element.
Rather than just add a second lookup into the hashmap after taking the
lock, fix this by reworking the function logic to take the lock before the
initial lookup.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Reported-and-tested-by: syzbot+4e7a85b1432052e8d6f8@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Mon, 16 Sep 2019 07:35:10 +0000 (09:35 +0200)]
Merge branch 'bpf-af-xdp-unaligned-fixes'
Ciara Loftus says:
====================
This patch set contains some fixes for AF_XDP zero copy in the i40e and
ixgbe drivers as well as a fix for the 'xdpsock' sample application when
running in unaligned mode.
Patches 1 and 2 fix a regression for the i40e and ixgbe drivers which
caused the umem headroom to be added to the xdp handle twice, resulting in
an incorrect value being received by the user for the case where the umem
headroom is non-zero.
Patch 3 fixes an issue with the xdpsock sample application whereby the
start of the tx packet data (offset) was not being set correctly when the
application was being run in unaligned mode.
This patch set has been applied against commit a2c11b034142 ("kcm: use
BPF_PROG_RUN")
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
samples/bpf: fix xdpsock l2fwd tx for unaligned mode
Preserve the offset of the address of the received descriptor, and include
it in the address set for the tx descriptor, so the kernel can correctly
locate the start of the packet data.
Fixes: 03895e63ff97 ("samples/bpf: add buffer recycling for unaligned chunks to xdpsock") Signed-off-by: Ciara Loftus <ciara.loftus@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 7cbbf9f1fa23 ("ixgbe: fix xdp handle calculations") reintroduced
the addition of the umem headroom to the xdp handle in the ixgbe_zca_free,
ixgbe_alloc_buffer_slow_zc and ixgbe_alloc_buffer_zc functions. However,
the headroom is already added to the handle in the function
ixgbe_run_xdp_zc. This commit removes the latter addition and fixes the
case where the headroom is non-zero.
Fixes: 7cbbf9f1fa23 ("ixgbe: fix xdp handle calculations") Signed-off-by: Ciara Loftus <ciara.loftus@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 4c5d9a7fa149 ("i40e: fix xdp handle calculations") reintroduced
the addition of the umem headroom to the xdp handle in the i40e_zca_free,
i40e_alloc_buffer_slow_zc and i40e_alloc_buffer_zc functions. However,
the headroom is already added to the handle in the function i40_run_xdp_zc.
This commit removes the latter addition and fixes the case where the
headroom is non-zero.
Fixes: 4c5d9a7fa149 ("i40e: fix xdp handle calculations") Signed-off-by: Ciara Loftus <ciara.loftus@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now that binutils and gcc support for BPF is upstream, make use of it in
BPF selftests using alu32-like approach. Share as much as possible of
CFLAGS calculation with clang.
Fixes only obvious issues, leaving more complex ones for later:
- Use gcc-provided bpf-helpers.h instead of manually defining the
helpers, change bpf_helpers.h include guard to avoid conflict.
- Include <linux/stddef.h> for __always_inline.
- Add $(OUTPUT)/../usr/include to include path in order to use local
kernel headers instead of system kernel headers when building with O=.
In order to activate the bpf-gcc support, one needs to configure
binutils and gcc with --target=bpf and make them available in $PATH. In
particular, gcc must be installed as `bpf-gcc`, which is the default.
Right now with binutils 25a2915e8dba and gcc r275589 only a handful of
tests work:
- Build errors:
- `error: too many function arguments for eBPF` for __always_inline
functions read_str_var and read_map_var - must be inlining issue,
and for process_l3_headers_v6, which relies on optimizing away
function arguments.
- `error: indirect call in function, which are not supported by eBPF`
where there are no obvious indirect calls in the source calls, e.g.
in __encap_ipip_none.
- `error: field 'lock' has incomplete type` for fields of `struct
bpf_spin_lock` type - bpf_spin_lock is re#defined by bpf-helpers.h,
so its usage is sensitive to order of #includes.
- `error: eBPF stack limit exceeded` in sysctl_tcp_mem.
- Load errors:
- Missing object files due to above build errors.
- `libbpf: failed to create map (name: 'test_ver.bss')`.
- `libbpf: object file doesn't contain bpf program`.
- `libbpf: Program '.text' contains unrecognized relo data pointing to
section 0`.
- `libbpf: BTF is required, but is missing or corrupted` - no BTF
support in gcc yet.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Jose E. Marchesi <jose.marchesi@oracle.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
net: stmmac: socfpga: re-use the `interface` parameter from platform data
The socfpga sub-driver defines an `interface` field in the `socfpga_dwmac`
struct and parses it on init.
The shared `stmmac_probe_config_dt()` function also parses this from the
device-tree and makes it available on the returned `plat_data` (which is
the same data available via `netdev_priv()`).
All that's needed now is to dig that information out, via some
`dev_get_drvdata()` && `netdev_priv()` calls and re-use it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
More fixes for unlocked cls hardware offload API refactoring
Two fixes for my "Refactor cls hardware offload API to support
rtnl-independent drivers" series and refactoring patch that implements
infrastructure necessary for the fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: use get_dev() action API in flow_action infra
When filling in hardware intermediate representation tc_setup_flow_action()
directly obtains, checks and takes reference to dev used by mirred action,
instead of using act->ops->get_dev() API created specifically for this
purpose. In order to remove code duplication, refactor flow_action infra to
use action API when obtaining mirred action target dev. Extend get_dev()
with additional argument that is used to provide dev destructor to the
user.
Fixes: 5a6ff4b13d59 ("net: sched: take reference to action dev before calling offloads") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: take reference to psample group in flow_action infra
With recent patch set that removed rtnl lock dependency from cls hardware
offload API rtnl lock is only taken when reading action data and can be
released after action-specific data is parsed into intermediate
representation. However, sample action psample group is passed by pointer
without obtaining reference to it first, which makes it possible to
concurrently overwrite the action and deallocate object pointed by
psample_group pointer after rtnl lock is released but before driver
finished using the pointer.
To prevent such race condition, obtain reference to psample group while it
is used by flow_action infra. Extend psample API with function
psample_group_take() that increments psample group reference counter.
Extend struct tc_action_ops with new get_psample_group() API. Implement the
API for action sample using psample_group_take() and already existing
psample_group_put() as a destructor. Use it in tc_setup_flow_action() to
take reference to psample group pointed to by entry->sample.psample_group
and release it in tc_cleanup_flow_action().
Disable bh when taking psample_groups_lock. The lock is now taken while
holding action tcf_lock that is used by data path and requires bh to be
disabled, so doing the same for psample_groups_lock is necessary to
preserve SOFTIRQ-irq-safety.
Fixes: 918190f50eb6 ("net: sched: flower: don't take rtnl lock for cls hw offloads API") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: extend flow_action_entry with destructor
Generalize flow_action_entry cleanup by extending the structure with
pointer to destructor function. Set the destructor in
tc_setup_flow_action(). Refactor tc_cleanup_flow_action() to call
entry->destructor() instead of using switch that dispatches by entry->id
and manually executes cleanup.
This refactoring is necessary for following patches in this series that
require destructor to use tc_action->ops callbacks that can't be easily
obtained in tc_cleanup_flow_action().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rain River [Fri, 13 Sep 2019 13:43:45 +0000 (21:43 +0800)]
MAINTAINERS: update FORCEDETH MAINTAINERS info
Many FORCEDETH NICs are used in our hosts. Several bugs are fixed and
some features are developed for FORCEDETH NICs. And I have been
reviewing patches for FORCEDETH NIC for several months. Mark me as the
FORCEDETH NIC maintainer. I will send out the patches and maintain
FORCEDETH NIC.
Signed-off-by: Rain River <rain.1986.08.12@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 13 Sep 2019 13:28:17 +0000 (16:28 +0300)]
net/wan: dscc4: remove broken dscc4 driver
Using static analysis, I discovered that the "dpriv->pci_priv->pdev"
pointer is always NULL. This pointer was supposed to be initialized
during probe and is essential for the driver to work. It would be easy
to add a "ppriv->pdev = pdev;" to dscc4_found1() but this driver has
been broken since before we started using git and no one has complained
so probably we should just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Fri, 13 Sep 2019 12:47:27 +0000 (13:47 +0100)]
MAINTAINERS: xen-netback: update my email address
My Citrix email address will expire shortly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wl@xen.org> Acked-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Fri, 13 Sep 2019 09:50:32 +0000 (11:50 +0200)]
net: stmmac: Hold rtnl lock in suspend/resume callbacks
We need to hold rnl lock in suspend and resume callbacks because phylink
requires it. Otherwise we will get a WARN() in suspend and resume.
Also, move phylink start and stop callbacks to inside device's internal
lock so that we prevent concurrent HW accesses.
Fixes: 74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic") Reported-by: Christophe ROULLIER <christophe.roullier@st.com> Tested-by: Christophe ROULLIER <christophe.roullier@st.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 13 Sep 2019 09:45:47 +0000 (17:45 +0800)]
ip6_gre: fix a dst leak in ip6erspan_tunnel_xmit
In ip6erspan_tunnel_xmit(), if the skb will not be sent out, it has to
be freed on the tx_err path. Otherwise when deleting a netns, it would
cause dst/dev to leak, and dmesg shows:
unregister_netdevice: waiting for lo to become free. Usage count = 1
Fixes: ef7baf5e083c ("ip6_gre: add ip6 erspan collect_md mode") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 13 Sep 2019 09:07:59 +0000 (10:07 +0100)]
qed: fix spelling mistake "fullill" -> "fulfill"
There is a spelling mistake in a DP_VERBOSE debug message. Fix it.
(Using American English spelling as this is the most common way
to spell this in the kernel).
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 13 Sep 2019 01:16:39 +0000 (21:16 -0400)]
udp: correct reuseport selection with connected sockets
UDP reuseport groups can hold a mix unconnected and connected sockets.
Ensure that connections only receive all traffic to their 4-tuple.
Fast reuseport returns on the first reuseport match on the assumption
that all matches are equal. Only if connections are present, return to
the previous behavior of scoring all sockets.
Record if connections are present and if so (1) treat such connected
sockets as an independent match from the group, (2) only return
2-tuple matches from reuseport and (3) do not return on the first
2-tuple reuseport match to allow for a higher scoring match later.
New field has_conns is set without locks. No other fields in the
bitmap are modified at runtime and the field is only ever set
unconditionally, so an RMW cannot miss a change.
Fixes: e32ea7e74727 ("soreuseport: fast reuseport UDP socket selection") Link: http://lkml.kernel.org/r/CA+FuTSfRP09aJNYRt04SS6qj22ViiOEWaWmLAwX0psk8-PGNxw@mail.gmail.com Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Craig Gallek <kraig@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hou Tao [Tue, 21 May 2019 07:59:03 +0000 (15:59 +0800)]
block: make rq sector size accessible for block stats
Currently rq->data_len will be decreased by partial completion or
zeroed by completion, so when blk_stat_add() is invoked, data_len
will be zero and there will never be samples in poll_cb because
blk_mq_poll_stats_bkt() will return -1 if data_len is zero.
We could move blk_stat_add() back to __blk_mq_complete_request(),
but that would make the effort of trying to call ktime_get_ns()
once in vain. Instead we can reuse throtl_size field, and use
it for both block stats and block throttle, and adjust the
logic in blk_mq_poll_stats_bkt() accordingly.
Fixes: 4bc6339a583c ("block: move blk_stat_add() to __blk_mq_end_request()") Tested-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is sad, and done for all the wrong reasons. Because that commit is
good, and does exactly what it says: avoids a lot of small disk requests
for the inode table read-ahead.
However, it turns out that it causes an entirely unrelated problem: the
getrandom() system call was introduced back in 2014 by commit c6e9d6f38894 ("random: introduce getrandom(2) system call"), and people
use it as a convenient source of good random numbers.
But part of the current semantics for getrandom() is that it waits for
the entropy pool to fill at least partially (unlike /dev/urandom). And
at least ArchLinux apparently has a systemd that uses getrandom() at
boot time, and the improvements in IO patterns means that existing
installations suddenly start hanging, waiting for entropy that will
never happen.
It seems to be an unlucky combination of not _quite_ enough entropy,
together with a particular systemd version and configuration. Lennart
says that the systemd-random-seed process (which is what does this early
access) is supposed to not block any other boot activity, but sadly that
doesn't actually seem to be the case (possibly due bogus dependencies on
cryptsetup for encrypted swapspace).
The correct fix is to fix getrandom() to not block when it's not
appropriate, but that fix is going to take a lot more discussion. Do we
just make it act like /dev/urandom by default, and add a new flag for
"wait for entropy"? Do we add a boot-time option? Or do we just limit
the amount of time it will wait for entropy?
So in the meantime, we do the revert to give us time to discuss the
eventual fix for the fundamental problem, at which point we can re-apply
the ext4 inode table access optimization.
Reported-by: Ahmed S. Darwish <darwish.07@gmail.com> Cc: Ted Ts'o <tytso@mit.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Alexander E. Patrakov <patrakov@gmail.com> Cc: Lennart Poettering <mzxreary@0pointer.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/rds: Fix 'ib_evt_handler_call' element in 'rds_ib_stat_names'
All entries in 'rds_ib_stat_names' are stringified versions
of the corresponding "struct rds_ib_statistics" element
without the "s_"-prefix.
Fix entry 'ib_evt_handler_call' to do the same.
Fixes: f4f943c958a2 ("RDS: IB: ack more receive completions to improve performance") Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 12 Sep 2019 13:16:45 +0000 (15:16 +0200)]
net: dsa: Fix load order between DSA drivers and taggers
The DSA core, DSA taggers and DSA drivers all make use of
module_init(). Hence they get initialised at device_initcall() time.
The ordering is non-deterministic. It can be a DSA driver is bound to
a device before the needed tag driver has been initialised, resulting
in the message:
No tagger for this switch
Rather than have this be fatal, return -EPROBE_DEFER so that it is
tried again later once all the needed drivers have been loaded.
Fixes: d3b8c04988ca ("dsa: Add boilerplate helper to register DSA tag driver modules") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 12 Sep 2019 10:02:42 +0000 (12:02 +0200)]
net/sched: fix race between deactivation and dequeue for NOLOCK qdisc
The test implemented by some_qdisc_is_busy() is somewhat loosy for
NOLOCK qdisc, as we may hit the following scenario:
CPU1 CPU2
// in net_tx_action()
clear_bit(__QDISC_STATE_SCHED...);
// in some_qdisc_is_busy()
val = (qdisc_is_running(q) ||
test_bit(__QDISC_STATE_SCHED,
&q->state));
// here val is 0 but...
qdisc_run(q)
// ... CPU1 is going to run the qdisc next
As a conseguence qdisc_run() in net_tx_action() can race with qdisc_reset()
in dev_qdisc_reset(). Such race is not possible for !NOLOCK qdisc as
both the above bit operations are under the root qdisc lock().
After commit 021a17ed796b ("pfifo_fast: drop unneeded additional lock on dequeue")
the race can cause use after free and/or null ptr dereference, but the root
cause is likely older.
This patch addresses the issue explicitly checking for deactivation under
the seqlock for NOLOCK qdisc, so that the qdisc_run() in the critical
scenario becomes a no-op.
Note that the enqueue() op can still execute concurrently with dev_qdisc_reset(),
but that is safe due to the skb_array() locking, and we can't avoid that
for NOLOCK qdiscs.
Fixes: 021a17ed796b ("pfifo_fast: drop unneeded additional lock on dequeue") Reported-by: Li Shuang <shuali@redhat.com> Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 14 Sep 2019 11:24:21 +0000 (12:24 +0100)]
Documentation: kbuild: Add document about reproducible builds
In the Distribution Kernels track at Linux Plumbers Conference there
was some discussion around the difficulty of making kernel builds
reproducible.
This is a solved problem, but the solutions don't appear to be
documented in one place. This document lists the issues I know about
and the settings needed to ensure reproducibility.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"The main change here is a revert of reverts. We recently simplified
some code that was thought unnecessary; however, since then KVM has
grown quite a few cond_resched()s and for that reason the simplified
code is prone to livelocks---one CPUs tries to empty a list of guest
page tables while the others keep adding to them. This adds back the
generation-based zapping of guest page tables, which was not
unnecessary after all.
On top of this, there is a fix for a kernel memory leak and a couple
of s390 fixlets as well"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86/mmu: Reintroduce fast invalidate/zap for flushing memslot
KVM: x86: work around leak of uninitialized stack contents
KVM: nVMX: handle page fault in vmread
KVM: s390: Do not leak kernel stack data in the KVM_S390_INTERRUPT ioctl
KVM: s390: kvm_s390_vm_start_migration: check dirty_bitmap before using it as target for memset()
Daniel Xu [Sat, 14 Sep 2019 21:23:45 +0000 (14:23 -0700)]
io_uring: increase IORING_MAX_ENTRIES to 32K
Some workloads can require far more than 4K oustanding entries. For
example memcached can have ~300K sockets over ~40 cores. Bumping the max
to 32K seems to work pretty well.
Reported-by: Dan Melnic <dmm@fb.com> Signed-off-by: Daniel Xu <dxu@dxuuu.xyz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge tag 'riscv/for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Paul Walmsley:
"Last week, Palmer and I learned that there was an error in the RISC-V
kernel image header format that could make it less compatible with the
ARM64 kernel image header format. I had missed this error during my
original reviews of the patch.
The kernel image header format is an interface that impacts
bootloaders, QEMU, and other user tools. Those packages must be
updated to align with whatever is merged in the kernel. We would like
to avoid proliferating these image formats by keeping the RISC-V
header as close as possible to the existing ARM64 header. Since the
arch/riscv patch that adds support for the image header was merged
with our v5.3-rc1 pull request as commit 0f327f2aaad6a ("RISC-V: Add
an Image header that boot loader can parse."), we think it wise to try
to fix this error before v5.3 is released.
The fix itself should be backwards-compatible with any project that
has already merged support for premature versions of this interface.
It primarily involves ensuring that the RISC-V image header has
something useful in the same field as the ARM64 image header"
* tag 'riscv/for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: modify the Image header to improve compatibility with the ARM64 header
1) Don't corrupt xfrm_interface parms before validation, from Nicolas
Dichtel.
2) Revert use of usb-wakeup in btusb, from Mario Limonciello.
3) Block ipv6 packets in bridge netfilter if ipv6 is disabled, from
Leonardo Bras.
4) IPS_OFFLOAD not honored in ctnetlink, from Pablo Neira Ayuso.
5) Missing ULP check in sock_map, from John Fastabend.
6) Fix receive statistic handling in forcedeth, from Zhu Yanjun.
7) Fix length of SKB allocated in 6pack driver, from Christophe
JAILLET.
8) ip6_route_info_create() returns an error pointer, not NULL. From
Maciej Żenczykowski.
9) Only add RDS sock to the hashes after rs_transport is set, from
Ka-Cheong Poon.
10) Don't double clean TX descriptors in ixgbe, from Ilya Maximets.
11) Presence of transmit IPSEC offload in an SKB is not tested for
correctly in ixgbe and ixgbevf. From Steffen Klassert and Jeff
Kirsher.
12) Need rcu_barrier() when register_netdevice() takes one of the
notifier based failure paths, from Subash Abhinov Kasiviswanathan.
13) Fix leak in sctp_do_bind(), from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
cdc_ether: fix rndis support for Mediatek based smartphones
sctp: destroy bucket if failed to bind addr
sctp: remove redundant assignment when call sctp_get_port_local
sctp: change return type of sctp_get_port_local
ixgbevf: Fix secpath usage for IPsec Tx offload
sctp: Fix the link time qualifier of 'sctp_ctrlsock_exit()'
ixgbe: Fix secpath usage for IPsec TX offload.
net: qrtr: fix memort leak in qrtr_tun_write_iter
net: Fix null de-reference of device refcount
ipv6: Fix the link time qualifier of 'ping_v6_proc_exit_net()'
tun: fix use-after-free when register netdev failed
tcp: fix tcp_ecn_withdraw_cwr() to clear TCP_ECN_QUEUE_CWR
ixgbe: fix double clean of Tx descriptors with xdp
ixgbe: Prevent u8 wrapping of ITR value to something less than 10us
mlx4: fix spelling mistake "veify" -> "verify"
net: hns3: fix spelling mistake "undeflow" -> "underflow"
net: lmc: fix spelling mistake "runnin" -> "running"
NFC: st95hf: fix spelling mistake "receieve" -> "receive"
net/rds: An rds_sock is added too early to the hash table
mac80211: Do not send Layer 2 Update frame before authorization
...
Merge tag 'drm-fixes-2019-09-13' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"From the maintainer summit, just some last minute fixes for final:
lima:
- fix gem_wait ioctl
core:
- constify modes list
i915:
- DP MST high color depth regression
- GPU hangs on vulkan compute workloads"
* tag 'drm-fixes-2019-09-13' of git://anongit.freedesktop.org/drm/drm:
drm/lima: fix lima_gem_wait() return value
drm/i915: Restore relaxed padding (OCL_OOB_SUPPRES_ENABLE) for skl+
drm/i915: Limit MST to <= 8bpc once again
drm/modes: Make the whitelist more const
Pavel Begunkov [Sat, 14 Sep 2019 17:31:50 +0000 (20:31 +0300)]
bfq: Fix bfq linkage error
Since commit 795fe54c2a828099e ("bfq: Add per-device weight"), bfq uses
blkg_conf_prep() and blkg_conf_finish(), which are not exported. So, it
causes linkage error if bfq compiled as a module.
Joe Perches [Fri, 6 Sep 2019 21:11:51 +0000 (14:11 -0700)]
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
As Linus said in:
https://lore.kernel.org/lkml/CAHk-=wgoxnmsj8GEVFJSvTwdnWm8wVJthefNk2n6+4TC=20e0Q@mail.gmail.com/
It's a pointless warning, making for more complex code, and
making people remember esoteric printf format details that have no
reason for existing.
The "h" and "hh" things should never be used. The only reason for them
being used if if you have an "int", but you want to print it out as a
"char" (and honestly, that is a really bad reason, you'd be better off
just using a proper cast to make the code more obvious).
So if what you have a "char" (or unsigned char) you should always just
print it out as an "int", knowing that the compiler already did the
proper type conversion.
Signed-off-by: Joe Perches <joe@perches.com> Reviewed-by: Louis Taylor <louis@kragniz.eu> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Federico Vaga [Sun, 8 Sep 2019 06:29:01 +0000 (08:29 +0200)]
doc:lock: remove reference to clever use of read-write lock
Remove the clever example about read-write lock because this type of
lock is not recommended anymore (according to the very same document).
So there is no reason to teach clever things that people should not do.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
KVM: x86/mmu: Reintroduce fast invalidate/zap for flushing memslot
James Harvey reported a livelock that was introduced by commit d012a06ab1d23 ("Revert "KVM: x86/mmu: Zap only the relevant pages when
removing a memslot"").
The livelock occurs because kvm_mmu_zap_all() as it exists today will
voluntarily reschedule and drop KVM's mmu_lock, which allows other vCPUs
to add shadow pages. With enough vCPUs, kvm_mmu_zap_all() can get stuck
in an infinite loop as it can never zap all pages before observing lock
contention or the need to reschedule. The equivalent of kvm_mmu_zap_all()
that was in use at the time of the reverted commit (4e103134b8623, "KVM:
x86/mmu: Zap only the relevant pages when removing a memslot") employed
a fast invalidate mechanism and was not susceptible to the above livelock.
There are three ways to fix the livelock:
- Reverting the revert (commit d012a06ab1d23) is not a viable option as
the revert is needed to fix a regression that occurs when the guest has
one or more assigned devices. It's unlikely we'll root cause the device
assignment regression soon enough to fix the regression timely.
- Remove the conditional reschedule from kvm_mmu_zap_all(). However, although
removing the reschedule would be a smaller code change, it's less safe
in the sense that the resulting kvm_mmu_zap_all() hasn't been used in
the wild for flushing memslots since the fast invalidate mechanism was
introduced by commit 6ca18b6950f8d ("KVM: x86: use the fast way to
invalidate all pages"), back in 2013.
- Reintroduce the fast invalidate mechanism and use it when zapping shadow
pages in response to a memslot being deleted/moved, which is what this
patch does.
For all intents and purposes, this is a revert of commit ea145aacf4ae8
("Revert "KVM: MMU: fast invalidate all pages"") and a partial revert of
commit 7390de1e99a70 ("Revert "KVM: x86: use the fast way to invalidate
all pages""), i.e. restores the behavior of commit 5304b8d37c2a5 ("KVM:
MMU: fast invalidate all pages") and commit 6ca18b6950f8d ("KVM: x86:
use the fast way to invalidate all pages") respectively.
Fixes: d012a06ab1d23 ("Revert "KVM: x86/mmu: Zap only the relevant pages when removing a memslot"") Reported-by: James Harvey <jamespharvey20@gmail.com> Cc: Alex Willamson <alex.williamson@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: work around leak of uninitialized stack contents
Emulation of VMPTRST can incorrectly inject a page fault
when passed an operand that points to an MMIO address.
The page fault will use uninitialized kernel stack memory
as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just ensure
that the error code and CR2 are zero.
Paul Walmsley [Sat, 14 Sep 2019 01:35:50 +0000 (18:35 -0700)]
riscv: modify the Image header to improve compatibility with the ARM64 header
Part of the intention during the definition of the RISC-V kernel image
header was to lay the groundwork for a future merge with the ARM64
image header. One error during my original review was not noticing
that the RISC-V header's "magic" field was at a different size and
position than the ARM64's "magic" field. If the existing ARM64 Image
header parsing code were to attempt to parse an existing RISC-V kernel
image header format, it would see a magic number 0. This is
undesirable, since it's our intention to align as closely as possible
with the ARM64 header format. Another problem was that the original
"res3" field was not being initialized correctly to zero.
Address these issues by creating a 32-bit "magic2" field in the RISC-V
header which matches the ARM64 "magic" field. RISC-V binaries will
store "RSC\x05" in this field. The intention is that the use of the
existing 64-bit "magic" field in the RISC-V header will be deprecated
over time. Increment the minor version number of the file format to
indicate this change, and update the documentation accordingly. Fix
the assembler directives in head.S to ensure that reserved fields are
properly zero-initialized.
Wanpeng Li [Mon, 5 Aug 2019 02:03:22 +0000 (10:03 +0800)]
KVM: X86: Use IPI shorthands in kvm guest when support
IPI shorthand is supported now by linux apic/x2apic driver, switch to
IPI shorthand for all excluding self and all including self destination
shorthand in kvm guest, to avoid splitting the target mask into several
PV IPI hypercalls. This patch removes the kvm_send_ipi_all() and
kvm_send_ipi_allbutself() since the callers in APIC codes have already
taken care of apic_use_ipi_shorthand and fallback to ->send_IPI_mask
and ->send_IPI_mask_allbutself if it is false.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Nadav Amit <namit@vmware.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge branch 'md-next' of git://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-5.4/block
Pull MD fixes from Song.
* 'md-next' of git://git.kernel.org/pub/scm/linux/kernel/git/song/md:
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
====================
net: devlink: move reload fail indication to devlink core and expose to user
First two patches are dependencies of the last one. That moves devlink
reload failure indication to the devlink code, so the drivers do not
have to track it themselves. Currently it is only mlxsw, but I will send
a follow-up patchset that introduces this in netdevsim too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug introduced in Linux 3.14 we cannot determine the
correctly layout for a multi-zone RAID0 array - there are two
possibilities.
It is possible to tell the kernel which to chose using a module
parameter, but this can be clumsy to use. It would be best if
the choice were recorded in the metadata.
So add a feature flag for this purpose.
If it is set, then the 'layout' field of the superblock is used
to determine which layout to use.
If this flag is not set, then mddev->layout gets set to -1,
which causes the module parameter to be required.
Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com>
md/raid0: avoid RAID0 data corruption due to layout confusion.
If the drives in a RAID0 are not all the same size, the array is
divided into zones.
The first zone covers all drives, to the size of the smallest.
The second zone covers all drives larger than the smallest, up to
the size of the second smallest - etc.
A change in Linux 3.14 unintentionally changed the layout for the
second and subsequent zones. All the correct data is still stored, but
each chunk may be assigned to a different device than in pre-3.14 kernels.
This can lead to data corruption.
It is not possible to determine what layout to use - it depends which
kernel the data was written by.
So we add a module parameter to allow the old (0) or new (1) layout to be
specified, and refused to assemble an affected array if that parameter is
not set.
Fixes: 20d0189b1012 ("block: Introduce new bio_split()")
cc: stable@vger.kernel.org (3.14+) Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com>
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
If stripe in batch list is set with STRIPE_HANDLE flag, then the stripe
could be set with STRIPE_ACTIVE by the handle_stripe function. And if
error happens to the batch_head at the same time, break_stripe_batch_list
is called, then below warning could happen (the same report in [1]), it
means a member of batch list was set with STRIPE_ACTIVE.
Also commit 59fc630b8b5f9f ("RAID5: batch adjacent full stripe write")
said "If a stripe is added to batch list, then only the first stripe
of the list should be put to handle_list and run handle_stripe."
So don't set STRIPE_HANDLE to stripe which is already in batch list,
otherwise the stripe could be put to handle_list and run handle_stripe,
then the above warning could be triggered.
projects / linux.git / log