1) Limit the number of can filters to avoid > MAX_ORDER allocations.
Fix from Marc Kleine-Budde.
2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
configurations. From Stephen Hemminger.
3) Return proper error when memory allocation fails in
ser_gigaset_init(), from Dan Carpenter.
4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
Feng.
5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
Florian Fainelli.
6) Handle probe deferral properly in smsc911x driver.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: mlx5: Fix Kconfig help text
net: smsc911x: back out silently on probe deferrals
ibmveth: set correct gso_size and gso_type
net: ethernet: cpmac: Call SET_NETDEV_DEV()
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
vhost-vsock: fix orphan connection reset
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
ser_gigaset: return -ENOMEM on error instead of success
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
can: peak: fix bad memory access and free sequence
phy: Don't increment MDIO bus refcount unless it's a different owner
netvsc: reduce maximum GSO size
drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
can: raw: raw_setsockopt: limit number of can_filter that can be set
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet Signed-off-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 9 Dec 2016 13:18:00 +0000 (14:18 +0100)]
net: smsc911x: back out silently on probe deferrals
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:59:05 +0000 (22:59 -0500)]
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 8 Dec 2016 22:40:03 +0000 (16:40 -0600)]
ibmveth: set correct gso_size and gso_type
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com> Reviewed-by: David Dai <zdai@us.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:57 +0000 (11:41 -0800)]
udp: udp_rmem_release() should touch sk_rmem_alloc later
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:56 +0000 (11:41 -0800)]
udp: add batching to udp_rmem_release()
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:55 +0000 (11:41 -0800)]
udp: copy skb->truesize in the first cache line
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:11:15 +0000 (22:11 -0500)]
Merge branch 'qcom-emac'
Timur Tabi says:
====================
net: qcom/emac: simplify support for different SOCs
On SOCs that have the Qualcomm EMAC network controller, the internal
PHY block is always different. Sometimes the differences are small,
sometimes it might be a completely different IP. Either way, using version
numbers to differentiate them and putting all of the init code in one
file does not scale.
This patchset does two things: The first breaks up the current code into
different files, and the second patch adds support for a third SOC, the
Qualcomm Technologies QDF2400 ARM Server SOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:21 +0000 (13:24 -0600)]
net: qcom/emac: add support for the Qualcomm Technologies QDF2400
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:20 +0000 (13:24 -0600)]
net: qcom/emac: move phy init code to separate files
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 9 Dec 2016 19:27:22 +0000 (11:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Several fixes to the DSM (ACPI device specific method) marshaling
implementation.
I consider these urgent enough to send for 4.9 consideration since
they fix the kernel's handling of ARS (Address Range Scrub) commands.
Especially for platforms without machine-check-recovery capabilities,
successful execution of ARS commands enables the platform to
potentially break out of an infinite reboot problem if a media error
is present in the boot path. There is also a one line fix for a
device-dax read-only mapping regression.
Commits 9a901f5495e2 ("acpi, nfit: fix extended status translations
for ACPI DSMs") and 325896ffdf90 ("device-dax: fix private mapping
restriction, permit read-only") are true regression fixes for changes
introduced this cycle.
Commit efda1b5d87cb ("acpi, nfit, libnvdimm: fix / harden ars_status
output length handling") fixes the kernel's handling of zero-length
results, this never would have worked in the past, but we only just
recently discovered a BIOS implementation that emits this arguably
spec non-compliant result.
The remaining two commits are additional fall out from thinking
through the implications of a zero / truncated length result of the
ARS Status command.
In order to mitigate the risk that these changes introduce yet more
regressions they are backstopped by a new unit test in commit a7de92dac9f0 ("tools/testing/nvdimm: unit test acpi_nfit_ctl()") that
mocks up inputs to acpi_nfit_ctl()"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix private mapping restriction, permit read-only
tools/testing/nvdimm: unit test acpi_nfit_ctl()
acpi, nfit: fix bus vs dimm confusion in xlat_status
acpi, nfit: validate ars_status output buffer size
acpi, nfit, libnvdimm: fix / harden ars_status output length handling
acpi, nfit: fix extended status translations for ACPI DSMs
Linus Torvalds [Fri, 9 Dec 2016 19:07:45 +0000 (11:07 -0800)]
Merge branch 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"This is quite late but SCT Write Same support added during this cycle
is broken subtly but seriously and it'd be best to disable it before
v4.9 gets released.
This contains two commits - one low impact sata_mv fix and the
mentioned disabling of SCT Write Same"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata-scsi: disable SCT Write Same for the moment
ata: sata_mv: check for errors when parsing nr-ports from dt
Linus Torvalds [Fri, 9 Dec 2016 19:00:39 +0000 (11:00 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Final batch of SoC fixes
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3,
correcting number of SATA ports on a Marvell-based Linkstation
platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
freeze when starting up X"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
ARM: dts: imx7d: fix LCDIF clock assignment
dts: sun8i-h3: correct UART3 pin definitions
Linus Torvalds [Fri, 9 Dec 2016 18:54:54 +0000 (10:54 -0800)]
Merge tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- build fix for drivers calling ndelay() in a conditional block without
curly braces
- defconfig updates
* tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix ndelay() macro
m68k/defconfig: Update defconfigs for v4.9-rc1
Linus Torvalds [Fri, 9 Dec 2016 18:50:49 +0000 (10:50 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fix from Dave Airlie:
"Just a single fix for amdgpu to just suspend the gpu on 'shutdown'
instead of shutting it down fully, as for some reason the hw was
getting upset in some situations"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: just suspend the hw on pci shutdown
It shouldn't have come in yet - it depends on the changes in linux-next
that will come in during the next merge window. As Matthew Wilcox says,
the test suite is broken with the current state without the revert.
Requested-by: Matthew Wilcox <mawilcox@microsoft.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Thu, 8 Dec 2016 16:22:09 +0000 (17:22 +0100)]
cfg80211/mac80211: fix BSS leaks when abandoning assoc attempts
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vamsi Krishna [Fri, 2 Dec 2016 21:59:08 +0000 (23:59 +0200)]
nl80211: Use different attrs for BSSID and random MAC addr in scan req
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit ad2b26abc157 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d39177 ("cfg80211: Allow a scan request for a specific BSSID") Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com> Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes: e3978673f514 ("drivers: net: xgene: Fix MSS programming") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 8 Dec 2016 21:57:04 +0000 (22:57 +0100)]
net: xgene: move xgene_cle_ptree_ewdn data off stack
The array for initializing the cle is set up on the stack with
almost entirely constant data and then passed to a function that
converts it into HW specific bit patterns. With the latest
addition, the size of this array has grown to the point that
we get a warning about potential stack overflow in allmodconfig
builds:
xgene_enet_cle.c: In function ‘xgene_enet_cle_init’:
xgene_enet_cle.c:836:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Looking a bit deeper at the usage, I noticed that the only modification
of the data is in dead code, as we don't even use the cle module
for phy_mode other than PHY_INTERFACE_MODE_XGMII. This means we
can simply mark the structure constant and access it directly rather
than passing the pointer down through another structure, making
the code more efficient at the same time as avoiding the
warning.
Fixes: a809701fed15 ("drivers: net: xgene: fix: RSS for non-TCP/UDP") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 8 Dec 2016 21:57:03 +0000 (22:57 +0100)]
net/mlx5e: use %pad format string for dma_addr_t
On 32-bit ARM with 64-bit dma_addr_t I get this warning about an
incorrect format string:
In file included from /git/arm-soc/drivers/net/ethernet/mellanox/mlx5/core/alloc.c:42:0:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c: In function ‘mlx5_frag_buf_alloc_node’:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c:134:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
We have the special %pad format for printing dma_addr_t, so use that
to print the correct address and avoid the warning.
Fixes: 1c1b522808a1 ("net/mlx5e: Implement Fragmented Work Queue (WQ)") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
FMAN is the one that potentially needs patching as well (call
SET_NETDEV_DEV), but there appears to be no way that init_phy is
called right now, or there is not such an in-tree user. Madalin, can
you comment on that?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Tao [Thu, 8 Dec 2016 17:10:46 +0000 (01:10 +0800)]
vhost-vsock: fix orphan connection reset
local_addr.svm_cid is host cid. We should check guest cid instead,
which is remote_addr.svm_cid. Otherwise we end up resetting all
connections to all guests.
Cc: stable@vger.kernel.org [4.8+] Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Peng Tao <bergwolf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Dec 2016 23:40:15 +0000 (15:40 -0800)]
Merge branch 'parisc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Three important fixes for the parisc architecture.
Dave provided two patches: One which purges the TLB before setting a
PTE entry and a second one which drops unnecessary TLB flushes. Both
patches have been tested for one week on the debian buildd servers and
prevent random segmentation faults.
The patch from me fixes a crash at boot inside the TLB measuring code
on SMP machines with PA8000-PA8700 CPUs (specifically A500-44 and
J5000 servers)"
* 'parisc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix TLB related boot crash on SMP machines
parisc: Remove unnecessary TLB purges from flush_dcache_page_asm and flush_icache_page_asm
parisc: Purge TLB before setting PTE
Helge Deller [Thu, 8 Dec 2016 20:00:46 +0000 (21:00 +0100)]
parisc: Fix TLB related boot crash on SMP machines
At bootup we run measurements to calculate the best threshold for when we
should be using full TLB flushes instead of just flushing a specific amount of
TLB entries. This performance test is run over the kernel text segment.
But running this TLB performance test on the kernel text segment turned out to
crash some SMP machines when the kernel text pages were mapped as huge pages.
To avoid those crashes this patch simply skips this test on some SMP machines
and calculates an optimal threshold based on the maximum number of available
TLB entries and number of online CPUs.
On a technical side, this seems to happen:
The TLB measurement code uses flush_tlb_kernel_range() to flush specific TLB
entries with a page size of 4k (pdtlb 0(sr1,addr)). On UP systems this purge
instruction seems to work without problems even if the pages were mapped as
huge pages. But on SMP systems the TLB purge instruction is broadcasted to
other CPUs. Those CPUs then crash the machine because the page size is not as
expected. C8000 machines with PA8800/PA8900 CPUs were not affected by this
problem, because the required cache coherency prohibits to use huge pages at
all. Sadly I didn't found any documentation about this behaviour, so this
finding is purely based on testing with phyiscal SMP machines (A500-44 and
J5000, both were 2-way boxes).
Linus Torvalds [Thu, 8 Dec 2016 20:04:41 +0000 (12:04 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One small fix for a regression in a prior fix (again).
This time the condition in the prior fix BUG_ON proved to be wrong
under certain circumstances causing a BUG to trigger where it
shouldn't in the lpfc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
I didn't miss your "net-next is closed" email, but it did come as a bit
of a surprise, and due to time-zone differences I didn't have a chance
to react to it until now. We would have had a couple of patches in
bluetooth-next that we'd still have wanted to get to 4.10.
Out of these the most critical one is the H7/CT2 patch for Bluetooth
Security Manager Protocol, something that couldn't be published before
the Bluetooth 5.0 specification went public (yesterday). If these really
can't go to net-next we'll likely be sending at least this patch through
bluetooth.git to net.git for rc1 inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 19:25:14 +0000 (14:25 -0500)]
Merge branch 'xdp-head-adjustment'
Martin KaFai Lau says:
====================
Allow head adjustment in XDP prog
This series adds a helper to allow head adjusting in XDP prog. mlx4
driver has been modified to support this feature. An example is written
to encapsulate a packet with an IPv4/v6 header and then XDP_TX it
out.
v4:
1. Remove XDP_QUERY_FEATURES command. Instead, check
the prog->xdp_adjust_head bit inside the driver itself
during XDP_SETUP_PROG in patch 1of4.
Thanks for everybody's ideas.
2. Nit changes on sample code per Jesper
v3:
1. Check if the driver supports head adjustment before
setting the xdp_prog fd to the device in patch 1of4.
2. Remove the page alignment assumption on the data_hard_start.
Instead, add data_hard_start to the struct xdp_buff and the
driver has to fill it if it supports head adjustment.
3. Keep the wire MTU as before in mlx4
4. Set map0_byte_count to PAGE_SIZE in patch 3of4
v2:
1. Make a variable name change in bpf_xdp_adjust_head() in patch 1
2. Ensure no less than ETH_HLEN data in bpf_xdp_adjust_head() in patch 1
3. Some clarifications in commit log messages of patch 2 and 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The XDP prog checks if the incoming packet matches any VIP:PORT
combination in the BPF hashmap. If it is, it will encapsulate
the packet with a IPv4/v6 header as instructed by the value of
the BPF hashmap and then XDP_TX it out.
The VIP:PORT -> IP-Encap-Info can be specified by the cmd args
of the user prog.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 7 Dec 2016 11:22:03 +0000 (14:22 +0300)]
ser_gigaset: return -ENOMEM on error instead of success
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b95 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commmits 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
and 484611357c19 ("bpf: allow access into map value arrays") by themselves
are correct, but in combination they make state equivalence ignore 'id' field
of the register state which can lead to accepting invalid program.
Fixes: 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers") Fixes: 484611357c19 ("bpf: allow access into map value arrays") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 7 Dec 2016 17:19:33 +0000 (09:19 -0800)]
udp: under rx pressure, try to condense skbs
Under UDP flood, many softirq producers try to add packets to
UDP receive queue, and one user thread is burning one cpu trying
to dequeue packets as fast as possible.
Two parts of the per packet cost are :
- copying payload from kernel space to user space,
- freeing memory pieces associated with skb.
If socket is under pressure, softirq handler(s) can try to pull in
skb->head the payload of the packet if it fits.
Meaning the softirq handler(s) can free/reuse the page fragment
immediately, instead of letting udp_recvmsg() do this hundreds of usec
later, possibly from another node.
Additional gains :
- We reduce skb->truesize and thus can store more packets per SO_RCVBUF
- We avoid cache line misses at copyout() time and consume_skb() time,
and avoid one put_page() with potential alien freeing on NUMA hosts.
This comes at the cost of a copy, bounded to available tail room, which
is usually small. (We might have to fix GRO_MAX_HEAD which looks bigger
than necessary)
This patch gave me about 5 % increase in throughput in my tests.
skb_condense() helper could probably used in other contexts.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 18:21:40 +0000 (13:21 -0500)]
Merge branch 'liqudio-VF-data-path'
Raghu Vatsavayi says:
====================
liquidio VF data path
Following is V3 patch series that adds support for VF
data path related features. It also has following changes
related to previous comments:
1) Remove unnecessary "void *" casting.
2) Remove inline for functions and let gcc decide.
Please apply patches in following order as some of them
depend on earlier patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Shimizu [Thu, 1 Dec 2016 15:11:12 +0000 (00:11 +0900)]
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9ddb ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl") Reported-by: Ryan Tandy <ryan@nardis.ca> Tested-by: Ryan Tandy <ryan@nardis.ca> Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
David S. Miller [Thu, 8 Dec 2016 18:07:11 +0000 (13:07 -0500)]
Merge branch 'stmmac-DMA-burst'
Niklas Cassel says:
====================
net: stmmac: make DMA programmable burst length more configurable
Make DMA programmable burst length more configurable in the stmmac driver.
This is done by adding support for independent pbl for tx/rx through DT.
More fine grained tuning of pbl is possible thanks to a DT property saying
that we should NOT multiply pbl values by x8/x4 in hardware.
All new DT properties are optional, and created in a way that it will not
affect any existing DT configurations.
Changes since V1:
Created cover-letter.
Rebased patch set against next-20161205, since conflicting patches to
stmmac_platform.c has been merged since V1.
Changes since V2:
Moved default value initialization of pbl to stmmac_platform.c
and added a check for pbl != 0 in stmmac_main.c,
to catch a possble pbl == 0 from pci glue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:08 +0000 (15:20 +0100)]
net: smmac: allow configuring lower pbl values
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:07 +0000 (15:20 +0100)]
net: stmmac: add support for independent DMA pbl for tx/rx
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:05 +0000 (15:20 +0100)]
net: stmmac: stmmac_platform: fix parsing of DT binding
commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9fc, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9fc.
The issue commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:04 +0000 (15:20 +0100)]
net: stmmac: simplify the common DMA init API
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 14:20:03 +0000 (15:20 +0100)]
net: stmmac: return error if no DMA configuration is found
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 7 Dec 2016 13:43:30 +0000 (14:43 +0100)]
net: ethernet: slicoss: use module_pci_driver()
Use module_pci_driver() to get rid of some boilerplate code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Dec 2016 16:47:14 +0000 (11:47 -0500)]
Merge branch 'cls_flower-ICMP'
Simon Horman says:
====================
net/sched: cls_flower: Support matching on ICMP
this series adds support for matching on ICMP type and code to cls_flower.
Changes v5->v6:
* Restore missing signed-off-by
Changes v4->v5:
* Drop all helpers
Changes v3->v4:
* Do not add icmp to struct flow_keys, it is not needed
* Do not test for ICMP protocols in packet in __skb_flow_dissect,
this is also not needed
Changes v2->v3:
* Add FLOW_DISSECTOR_KEY_ICMP and use separate structure for ICMP
Changes v1->v2:
* Include all dissector helpers in first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 12:41:08 +0000 (13:41 +0100)]
net: stmmac: stmmac_platform: use correct setup function for gmac4
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Wed, 7 Dec 2016 12:41:06 +0000 (13:41 +0100)]
bindings: net: stmmac: correct note about TSO
snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.
TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.
Also added a note about snps,tso only being available on GMAC4 and newer.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 7 Dec 2016 12:25:29 +0000 (13:25 +0100)]
net: ll_temac: Utilize of_get_mac_address()
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Tobias Klauser [Wed, 7 Dec 2016 12:24:44 +0000 (13:24 +0100)]
net: axienet: Utilize of_get_mac_address()
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
David S. Miller [Thu, 8 Dec 2016 16:32:50 +0000 (11:32 -0500)]
Merge branch 'cls_flower-flags'
Or Gerlitz says:
====================
net/sched: cls_flower: Add support for matching on dissection flags
This series add the UAPI to provide set of flags for matching, where the
flags provided from user-space are mapped to flow-dissector flags.
The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.
v2->v3:
- replace BIT() with << (kbuild test robot)
v1->v2:
- dropped the flow dissector patch (#1) as no changes are needed there (Jiri)
- applied code review comments from Jiri to the flower patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 7 Dec 2016 12:03:11 +0000 (14:03 +0200)]
net/mlx5e: Offload TC matching on packets being IP fragments
Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 7 Dec 2016 12:03:10 +0000 (14:03 +0200)]
net/sched: cls_flower: Add support for matching on flags
Add UAPI to provide set of flags for matching, where the flags
provided from user-space are mapped to flow-dissector flags.
The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 7 Dec 2016 11:14:24 +0000 (14:14 +0300)]
drivers: net: xgene: uninitialized variable in xgene_enet_free_pagepool()
We never set "slots" in this function.
Fixes: a9380b0f7be8 ("drivers: net: xgene: Add support for Jumbo frame") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Wed, 7 Dec 2016 06:52:53 +0000 (14:52 +0800)]
icmp: correct return value of icmp_rcv()
Currently, icmp_rcv() always return zero on a packet delivery upcall.
To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Wed, 30 Nov 2016 20:56:46 +0000 (15:56 -0500)]
ceph: don't set req->r_locked_dir in ceph_d_revalidate
This function sets req->r_locked_dir which is supposed to indicate to
ceph_fill_trace that the parent's i_rwsem is locked for write.
Unfortunately, there is no guarantee that the dir will be locked when
d_revalidate is called, so we really don't want ceph_fill_trace to do
any dcache manipulation from this context. Clear req->r_locked_dir since
it's clearly not safe to do that.
What we really want to know with d_revalidate is whether the dentry
still points to the same inode. ceph_fill_trace installs a pointer to
the inode in req->r_target_inode, so we can just compare that to
d_inode(dentry) to see if it's the same one after the lookup.
Also, since we aren't generally interested in the parent here, we can
switch to using a GETATTR to hint that to the MDS, which also means that
we only need to reserve one cap.
Finally, just remove the d_unhashed check. That's really outside the
purview of a filesystem's d_revalidate. If the thing became unhashed
while we're checking it, then that's up to the VFS to handle anyway.
Fixes: 200fd27c8fa2 ("ceph: use lookup request to revalidate dentry") Link: http://tracker.ceph.com/issues/18041 Reported-by: Donatas Abraitis <donatas.abraitis@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: "Yan, Zheng" <zyan@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In case the user provided insufficient data, the code may return
prematurely without any operation. In this case, the processed
data indicated with outlen is zero.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
projects / linux.git / log