dmaengine: Create symlinks between DMA channels and slaves
Currently it is not easy to find out which DMA channels are in use, and
which slave devices are using which channels.
Fix this by creating two symlinks between the DMA channel and the actual
slave device when a channel is requested:
1. A "slave" symlink from DMA channel to slave device,
2. A "dma:<name>" symlink slave device to DMA channel.
When the channel is released, the symlinks are removed again.
The latter requires keeping track of the slave device and the channel
name in the dma_chan structure.
Note that this is limited to channel request functions for requesting an
exclusive slave channel that take a device pointer (dma_request_chan()
and dma_request_slave_channel*()).
Zhou Wang [Thu, 16 Jan 2020 06:10:57 +0000 (14:10 +0800)]
dmaengine: hisilicon: Add Kunpeng DMA engine support
This patch adds a driver for HiSilicon Kunpeng DMA engine. This DMA engine
which is an PCIe iEP offers 30 channels, each channel has a send queue, a
complete queue and an interrupt to help to do tasks. This DMA engine can do
memory copy between memory blocks or between memory and device buffer.
Dave Jiang [Tue, 21 Jan 2020 23:44:29 +0000 (16:44 -0700)]
dmaengine: idxd: add char driver to expose submission portal to userland
Create a char device region that will allow acquisition of user portals in
order to allow applications to submit DMA operations. A char device will be
created per work queue that gets exposed. The workqueue type "user"
is used to mark a work queue for user char device. For example if the
workqueue 0 of DSA device 0 is marked for char device, then a device node
of /dev/dsa/wq0.0 will be created.
Dave Jiang [Tue, 21 Jan 2020 23:44:23 +0000 (16:44 -0700)]
dmaengine: idxd: connect idxd to dmaengine subsystem
Add plumbing for dmaengine subsystem connection. The driver register a DMA
device per DSA device. The channels are dynamically registered when a
workqueue is configured to be "kernel:dmanegine" type.
Dave Jiang [Tue, 21 Jan 2020 23:44:05 +0000 (16:44 -0700)]
dmaengine: idxd: add configuration component of driver
The device is left unconfigured when the driver is loaded. Various
components are configured via the driver sysfs attributes. Once
configuration is done, the device can be enabled by writing the device name
to the bind attribute of the device driver sysfs. Disabling can be done
similarly. Also the individual work queues can also be enabled and disabled
through the bind/unbind attributes. A constructed hierarchy is created
through the struct device framework in order to provide appropriate
configuration points and device state and status. This hierarchy is
presented off the virtual DSA bus.
Dave Jiang [Tue, 21 Jan 2020 23:43:59 +0000 (16:43 -0700)]
dmaengine: idxd: Init and probe for Intel data accelerators
The idxd driver introduces the Intel Data Stream Accelerator [1] that will
be available on future Intel Xeon CPUs. One of the kernel access
point for the driver is through the dmaengine subsystem. It will initially
provide the DMA copy service to the kernel.
Some of the main functionality introduced with this accelerator
are: shared virtual memory (SVM) support, and descriptor submission using
Intel CPU instructions movdir64b and enqcmds. There will be additional
accelerator devices that share the same driver with variations to
capabilities.
This commit introduces the probe and initialization component of the
driver.
Dave Jiang [Tue, 21 Jan 2020 23:43:53 +0000 (16:43 -0700)]
dmaengine: add support to dynamic register/unregister of channels
With the channel registration routines broken out, now add support code to
allow independent registering and unregistering of channels in a hotplug fashion.
Dave Jiang [Tue, 21 Jan 2020 23:43:41 +0000 (16:43 -0700)]
x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
With the introduction of MOVDIR64B instruction, there is now an instruction
that can write 64 bytes of data atomically.
Quoting from Intel SDM:
"There is no atomicity guarantee provided for the 64-byte load operation
from source address, and processor implementations may use multiple
load operations to read the 64-bytes. The 64-byte direct-store issued
by MOVDIR64B guarantees 64-byte write-completion atomicity. This means
that the data arrives at the destination in a single undivided 64-byte
write transaction."
We have identified at least 3 different use cases for this instruction in
the format of func(dst, src, count):
1) Clear poison / Initialize MKTME memory
@dst is normal memory.
@src in normal memory. Does not increment. (Copy same line to all
targets)
@count (to clear/init multiple lines)
2) Submit command(s) to new devices
@dst is a special MMIO region for a device. Does not increment.
@src is normal memory. Increments.
@count usually is 1, but can be multiple.
3) Copy to iomem in big chunks
@dst is iomem and increments
@src in normal memory and increments
@count is number of chunks to copy
Add support for case #2 to support device that will accept commands via
this instruction. We provide a @count in order to submit a batch of
preprogrammed descriptors in virtually contiguous memory. This
allows the caller to submit multiple descriptors to a device with a single
submission. The special device requires the entire 64bytes descriptor to
be written atomically and will accept MOVDIR64B instruction.
Linus Torvalds [Fri, 24 Jan 2020 00:02:00 +0000 (16:02 -0800)]
Merge tag 'mmc-v5.5-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci: Fix minimum clock rate for v3 controllers
- sdhci-tegra: Fix SDR50 tuning override
- sdhci_am654: Fixup tuning issues and support for CQHCI
- sdhci_am654: Remove wrong write protect flag"
* tag 'mmc-v5.5-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: fix minimum clock rate for v3 controller
mmc: tegra: fix SDR50 tuning override
mmc: sdhci_am654: Fix Command Queuing in AM65x
mmc: sdhci_am654: Reset Command and Data line after tuning
mmc: sdhci_am654: Remove Inverted Write Protect flag
Guenter Roeck [Thu, 23 Jan 2020 02:41:18 +0000 (18:41 -0800)]
hwmon: (k10temp) Display up to eight sets of CCD temperatures
In HWiNFO, we see support for Tccd1, Tccd3, Tccd5, and Tccd7 temperature
sensors on Zen2 based Threadripper CPUs. Checking register maps on
Threadripper 3970X confirms SMN register addresses and values for those
sensors.
More analysis shows that EPYC CPUs support up to 8 CCD temperature
sensors. EPYC 7601 supports three CCD temperature sensors. Unlike
Zen2 CPUs, the register space in Zen1 CPUs supports a maximum of four
sensors, so only search for a maximum of four sensors on Zen1 CPUs.
On top of that, in thm_10_0_sh_mask.h in the Linux kernel, we find
definitions for THM_DIE{1-3}_TEMP__VALID_MASK, set to 0x00000800, as well
as matching SMN addresses. This lets us conclude that bit 11 of the
respective registers is a valid bit. With this assumption, the temperature
offset is now 49 degrees C. This conveniently matches the documented
temperature offset for Tdie, again suggesting that above registers indeed
report temperatures sensor values. Assume that bit 11 is indeed a valid
bit, and add support for the additional sensors.
With this patch applied, output from 3970X (idle) looks as follows:
Guenter Roeck [Fri, 17 Jan 2020 14:43:20 +0000 (06:43 -0800)]
hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
The maximum Tdie or Tctl is not published for Ryzen CPUs. What is
known, however, is that the traditional value of 70 degrees C is no
longer correct. On top of that, the limit applies to Tctl, not to Tdie.
Displaying it in either context is meaningless, confusing, and wrong.
Stop doing it.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com> Tested-by: Holger Kiehl <holger.kiehl@dwd.de> Tested-by: Michael Larabel <michael@phoronix.com> Tested-by: Jonathan McDowell <noodles@earth.li> Tested-by: Ken Moffat <zarniwhoop73@googlemail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Tue, 24 Dec 2019 15:20:55 +0000 (07:20 -0800)]
hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
Convert driver to use devm_hwmon_device_register_with_info to simplify
the code and to reduce its size.
Old size (x86_64):
text data bss dec hex filename
8247 4488 64 12799 31ff drivers/hwmon/k10temp.o
New size:
text data bss dec hex filename
6778 2792 64 9634 25a2 drivers/hwmon/k10temp.o
Tested-by: Brad Campbell <lists2009@fnarfbargle.com> Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at> Tested-by: Holger Kiehl <holger.kiehl@dwd.de> Tested-by: Michael Larabel <michael@phoronix.com> Tested-by: Jonathan McDowell <noodles@earth.li> Tested-by: Ken Moffat <zarniwhoop73@googlemail.com> Tested-by: Darren Salt <devspam@moreofthesa.me.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Akinobu Mita [Mon, 20 Jan 2020 15:32:24 +0000 (00:32 +0900)]
hwmon: (pwm-fan) stop fan on shutdown
The pwm-fan driver stops the fan in suspend but leaves the fan on in
shutdown. It seems strange to leave the fan on in shutdown because there
is no use case in my mind and the gpio-fan driver on the other hand stops
in shutdown.
This change turns off the fan in shutdown. If anyone complains then we'll
add an optional property to switch the behavior.
Vadim Pasternak [Mon, 13 Jan 2020 15:08:39 +0000 (15:08 +0000)]
hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
Add support for devices XDPE12254, XDPE12284.
All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.
Vadim Pasternak [Mon, 13 Jan 2020 15:08:36 +0000 (15:08 +0000)]
hwmon: (pmbus/core) Add support for vid mode detection per page bases
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.
Eddie James [Tue, 7 Jan 2020 15:40:40 +0000 (09:40 -0600)]
hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.
YueHaibing [Wed, 8 Jan 2020 03:45:14 +0000 (03:45 +0000)]
hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/hwmon/w83627ehf.c: In function 'w83627ehf_check_fan_inputs':
drivers/hwmon/w83627ehf.c:1296:24: warning:
variable 'fan4min' set but not used [-Wunused-but-set-variable]
commit 62000264cfa8 ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
left behind this unused variable.
Guenter Roeck [Fri, 29 Nov 2019 05:34:40 +0000 (21:34 -0800)]
hwmon: Driver for disk and solid state drives with temperature sensors
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Eddie James [Thu, 19 Dec 2019 20:50:05 +0000 (14:50 -0600)]
hwmon: (pmbus/ibm-cffps) Add new manufacturer debugfs entries
Add support for a number of manufacturer-specific registers in the
debugfs entries, as well as support to read and write the
PMBUS_ON_OFF_CONFIG register through debugfs.
Guenter Roeck [Thu, 12 Dec 2019 17:14:34 +0000 (09:14 -0800)]
hwmon: (pmbus) Detect if chip is write protected
If a chip is write protected, we can not change any limits, and we can
not clear status flags. This may be the reason why clearing status flags
is reported to not work for some chips. Detect the condition in the pmbus
core. If the chip is write protected, set limit attributes as read-only,
and set the flag indicating that the status flag should be ignored.
hwmon: Add support for enable attributes to hwmon core
The hwmon ABI supports enable attributes since commit fb41a710f84e
("hwmon: Document the sensor enable attribute"), but did not
add support for those attributes to the hwmon core. Do that now.
Since the enable attributes are logically the most important attributes,
they are added as first attribute to the attribute list. Move
hwmon_in_enable from last to first place for consistency.
Cong Wang [Wed, 22 Jan 2020 23:42:02 +0000 (15:42 -0800)]
net_sched: fix datalen for ematch
syzbot reported an out-of-bound access in em_nbyte. As initially
analyzed by Eric, this is because em_nbyte sets its own em->datalen
in em_nbyte_change() other than the one specified by user, but this
value gets overwritten later by its caller tcf_em_validate().
We should leave em->datalen untouched to respect their choices.
I audit all the in-tree ematch users, all of those implement
->change() set em->datalen, so we can just avoid setting it twice
in this case.
Reported-and-tested-by: syzbot+5af9a90dad568aa9f611@syzkaller.appspotmail.com Reported-by: syzbot+2f07903a5b05e7f36410@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Jan 2020 20:24:37 +0000 (21:24 +0100)]
Merge branch 'Fixes-for-SONIC-ethernet-driver'
Finn Thain says:
====================
Fixes for SONIC ethernet driver
Various SONIC driver problems have become apparent over the years,
including tx watchdog timeouts, lost packets and duplicated packets.
The problems are mostly caused by bugs in buffer handling, locking and
(re-)initialization code.
This patch series resolves these problems.
This series has been tested on National Semiconductor hardware (macsonic),
qemu-system-m68k (macsonic) and qemu-system-mips64el (jazzsonic).
The emulated dp8393x device used in QEMU also has bugs.
I have fixed the bugs that I know of in a series of patches at,
https://github.com/fthain/qemu/commits/sonic
Changed since v1:
- Minor revisions as described in commit logs.
- Deferred net-next patches.
Changed since v2:
- Minor revisions as described in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Prevent tx watchdog timeout
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Fix CAM initialization
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Quiesce SONIC before re-initializing descriptor memory
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Fix receive buffer replenishment
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Improve receive descriptor status flag check
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Avoid needless receive descriptor EOL flag updates
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Fix receive buffer handling
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Fix interface error stats collection
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Use MMIO accessors
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Clear interrupt flags immediately
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)]
net/sonic: Add mutual exclusion for accessing shared state
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Wed, 22 Jan 2020 14:15:14 +0000 (16:15 +0200)]
net: fsl/fman: rename IF_MODE_XGMII to IF_MODE_10G
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses a HW erratum on some QorIQ DPAA devices.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
When the issue was present, one could see such errors
during boot:
mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER]
bit may be falsely set when reading internal PCS registers.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Wed, 22 Jan 2020 09:43:38 +0000 (01:43 -0800)]
qlcnic: Fix CPU soft lockup while collecting firmware dump
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com> Tested-by: Yonggen Xu <Yonggen.Xu@dell.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 23 Jan 2020 19:37:19 +0000 (11:37 -0800)]
Merge tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"Primarily bugfixes, mostly around handling index wrap-around
correctly.
A couple of doc fixes and adding missing APIs.
I had an oops live on stage at linux.conf.au this year, and it turned
out to be a bug in xas_find() which I can't prove isn't triggerable in
the current codebase. Then in looking for the bug, I spotted two more
bugs.
The bots have had a few days to chew on this with no problems
reported, and it passes the test-suite (which now has more tests to
make sure these problems don't come back)"
* tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax:
XArray: Add xa_for_each_range
XArray: Fix xas_find returning too many entries
XArray: Fix xa_find_after with multi-index entries
XArray: Fix infinite loop with entry at ULONG_MAX
XArray: Add wrappers for nested spinlocks
XArray: Improve documentation of search marks
XArray: Fix xas_pause at ULONG_MAX
Linus Torvalds [Thu, 23 Jan 2020 19:23:37 +0000 (11:23 -0800)]
Merge tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for
multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and
calling trace_set_default_clock()
- A fix to a bug found with the double perf_event linking patch"
* tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobe: Fix to make trace_uprobe_filter alignment safe
tracing: Do not set trace clock if tracefs lockdown is in effect
tracing: Fix histogram code when expression has same var as value
tracing: trigger: Replace unneeded RCU-list traversals
tracing/uprobe: Fix double perf_event linking on multiprobe uprobe
tracing: xen: Ordered comparison of function pointers
Linus Torvalds [Thu, 23 Jan 2020 19:10:21 +0000 (11:10 -0800)]
Merge tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Prevent the kernel from crashing during resume from hibernation if
free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko)"
* tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: fix crashes with init_on_free=1
Linus Torvalds [Wed, 22 Jan 2020 20:37:25 +0000 (12:37 -0800)]
readdir: make user_access_begin() use the real access range
In commit 9f79b78ef744 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I changed filldir to not do individual __put_user()
accesses, but instead use unsafe_put_user() surrounded by the proper
user_access_begin/end() pair.
That make them enormously faster on modern x86, where the STAC/CLAC
games make individual user accesses fairly heavy-weight.
However, the user_access_begin() range was not really the exact right
one, since filldir() has the unfortunate problem that it needs to not
only fill out the new directory entry, it also needs to fix up the
previous one to contain the proper file offset.
It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the
file offset of the directory entry itself - it's the offset of the next
one. So we end up backfilling the offset in the previous entry as we
walk along.
But since x86 didn't really care about the exact range, and used to be
the only architecture that did anything fancy in user_access_begin() to
begin with, the filldir[64]() changes did something lazy, and even
commented on it:
/*
* Note! This range-checks 'previous' (which may be NULL).
* The real range was checked in getdents
*/
if (!user_access_begin(dirent, sizeof(*dirent)))
goto efault;
and it all worked fine.
But now 32-bit ppc is starting to also implement user_access_begin(),
and the fact that we faked the range to only be the (possibly not even
valid) previous directory entry becomes a problem, because ppc32 will
actually be using the range that is passed in for more than just "check
that it's user space".
This is a complete rewrite of Christophe's original patch.
By saving off the record length of the previous entry instead of a
pointer to it in the filldir data structures, we can simplify the range
check and the writing of the previous entry d_off field. No need for
any conditionals in the user accesses themselves, although we retain the
conditional EINTR checking for the "was this the first directory entry"
signal handling latency logic.
Linus Torvalds [Thu, 23 Jan 2020 18:05:05 +0000 (10:05 -0800)]
readdir: be more conservative with directory entry names
Commit 8a23eb804ca4 ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Kristian Evensen [Thu, 23 Jan 2020 12:20:18 +0000 (13:20 +0100)]
fou: Fix IPv6 netlink policy
When submitting v2 of "fou: Support binding FoU socket" (1713cb37bf67),
I accidentally sent the wrong version of the patch and one fix was
missing. In the initial version of the patch, as well as the version 2
that I submitted, I incorrectly used ".type" for the two V6-attributes.
The correct is to use ".len".
Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 1713cb37bf67 ("fou: Support binding FoU socket") Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Jan 2020 13:30:20 +0000 (14:30 +0100)]
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jan 2020 17:07:35 +0000 (09:07 -0800)]
tun: add mutex_unlock() call and napi.skb clearing in tun_get_user()
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Petar Penkov <ppenkov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 22 Jan 2020 18:09:52 +0000 (20:09 +0200)]
mlxsw: spectrum_acl: Fix use-after-free during reload
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200dead000000000100dead000000000122ffff888236403500
[ 123.734646] raw: 0000000000000000000000000010001000000001ffffffff0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc/mm/hash: Fix sharing context ids between kernel & userspace
Commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in
the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT.
The result is that the context id used for the vmemmap and the lowest
context id handed out to userspace are the same. The context id is
essentially the process identifier as far as the first stage of the
MMU translation is concerned.
This can result in multiple SLB entries with the same VSID (Virtual
Segment ID), accessible to the kernel and some random userspace
process that happens to get the overlapping id, which is not expected
eg:
Even though the user process and the kernel use the same VSID, the
permissions in the hash page table prevent the user process from
reading or writing to any kernel mappings.
It can also lead to SLB entries with different base page size
encodings (LLP), eg:
This happens with 256MB segments and 64K pages, as the duplicate VSID
is hit with the first vmemmap segment and the first user segment, and
older 32-bit userspace maps things in the first user segment.
On other CPUs a machine check is not seen. Instead the userspace
process can get stuck continuously faulting, with the fault never
properly serviced, due to the kernel not understanding that there is
already a HPTE for the address but with inaccessible permissions.
On machines with 1T segments we've not seen the bug hit other than by
deliberately exercising it. That seems to be just a matter of luck
though, due to the typical layout of the user virtual address space
and the ranges of vmemmap that are typically populated.
To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest
context given to userspace doesn't overlap with the VMEMMAP context,
or with the context for INVALID_REGION_ID.
Fixes: 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range") Cc: stable@vger.kernel.org # v5.2+ Reported-by: Christian Marillat <marillat@debian.org> Reported-by: Romain Dolbeau <romain@dolbeau.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Account for INVALID_REGION_ID, mostly rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
Hayes Wang [Wed, 22 Jan 2020 08:02:13 +0000 (16:02 +0800)]
r8152: disable DelayPhyPwrChg
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Wed, 22 Jan 2020 08:02:12 +0000 (16:02 +0800)]
r8152: avoid the MCU to clear the lanwake
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log