David Frey [Thu, 19 Sep 2019 22:54:18 +0000 (15:54 -0700)]
iio: light: opt3001: fix mutex unlock race
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com> Fixes: 94a9b7b1809f ("iio: light: add support for TI's opt3001 light sensor") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marco Felsch [Tue, 17 Sep 2019 16:09:23 +0000 (18:09 +0200)]
iio: adc: ad799x: fix probe error handling
Since commit 0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marco Felsch [Tue, 17 Sep 2019 14:56:37 +0000 (16:56 +0200)]
iio: light: add missing vcnl4040 of_compatible
Commit 5a441aade5b3 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Fixes: 5a441aade5b3 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor") Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Marco Felsch [Tue, 17 Sep 2019 14:56:36 +0000 (16:56 +0200)]
iio: light: fix vcnl4000 devicetree hooks
Since commit ebd457d55911 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Lorenzo Bianconi [Mon, 16 Sep 2019 22:01:29 +0000 (00:01 +0200)]
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844ebd ("iio: imu: st_lsm6dsx: add i2c embedded controller support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Hans de Goede [Sun, 15 Sep 2019 18:53:42 +0000 (20:53 +0200)]
iio: adc: axp288: Override TS pin bias current for some models
Since commit 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Stefan Popa [Tue, 10 Sep 2019 14:44:46 +0000 (17:44 +0300)]
iio: accel: adxl372: Perform a reset at start up
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com> Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stefan Popa [Tue, 10 Sep 2019 14:44:21 +0000 (17:44 +0300)]
iio: accel: adxl372: Fix push to buffers lost samples
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com> Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stefan Popa [Tue, 10 Sep 2019 14:43:32 +0000 (17:43 +0300)]
iio: accel: adxl372: Fix/remove limitation for FIFO samples
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com> Fixes: f4f55ce38e5f ("iio:adxl372: Add FIFO and interrupts support") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Mon, 9 Sep 2019 12:37:21 +0000 (14:37 +0200)]
iio: adc: hx711: fix bug in sampling of data
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea7e ("iio: adc: hx711: Add IIO driver for AVIA HX711") Signed-off-by: Andreas Klinger <ak@it-klinger.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pascal Bouwmann [Thu, 29 Aug 2019 05:29:41 +0000 (07:29 +0200)]
iio: fix center temperature of bmc150-accel-core
The center temperature of the supported devices stored in the constant
BMC150_ACCEL_TEMP_CENTER_VAL is not 24 degrees but 23 degrees.
It seems that some datasheets were inconsistent on this value leading
to the error. For most usecases will only make minor difference so
not queued for stable.
Signed-off-by: Pascal Bouwmann <bouwmann@tau-tec.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Sat, 31 Aug 2019 11:18:22 +0000 (13:18 +0200)]
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
Do not allow configuring null sensor gain since it will force to 0
device outputs
Fixes: c8d4066c7246 ("iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: meson_saradc: Fix memory allocation order
meson_saradc's irq handler uses priv->regmap so make sure that it is
allocated before the irq get enabled.
This also fixes crash when CONFIG_DEBUG_SHIRQ is enabled, as device
managed resources are freed in the inverted order they had been
allocated, priv->regmap was freed before the spurious fake irq that
CONFIG_DEBUG_SHIRQ adds called the handler.
Fixes: 3af109131b7eb8 ("iio: adc: meson-saradc: switch from polling to interrupt mode") Reported-by: Elie Roudninski <xademax@gmail.com> Signed-off-by: Remi Pommarel <repk@triplefau.lt> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Elie ROUDNINSKI <xademax@gmail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Colin Ian King [Thu, 5 Sep 2019 15:22:27 +0000 (16:22 +0100)]
staging: rtl8723bs: hal: remove redundant variable n
The variable n is being assigned a value that is never read inside
an if statement block, the assignment is redundant and can be removed.
With this removed, n is only being used for a constant loop bounds
check, so replace n with that value instead and remove n completely.
("iio: hid-sensor-attributes: Convert to use int_pow()")
converted to use generic int_pow() helper. Though, the generic one returns
64-bit value and, in cases when it is used as divisor, it compels 64-bit
division from compiler.
In order to fix this, introduce a temporary 32-bit variable to hold the result
of int_pow() and use it as divisor afterwards.
In couple of cases, replace int_pow() with a predefined unit factors for time
and frequency.
Fixes: 473d12f7638c ("iio: hid-sensor-attributes: Convert to use int_pow()") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://lore.kernel.org/r/20190905112759.13035-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
erofs: use read_cache_page_gfp for erofs_get_meta_page
As Christoph said [1], "I'd much prefer to just use
read_cache_page_gfp, and live with the fact that this
allocates bufferheads behind you for now. I'll try to
speed up my attempts to get rid of the buffer heads on
the block device mapping instead. "
This simplifies the code a lot and a minor thing is
"no REQ_META (e.g. for blktrace) on metadata at all..."
As Christoph said [1] [2], "Just use the slightly
more complicated 32-bit version everywhere so that
you have a single actually tested code path.
And then remove this helper. "
As Christoph said [1], "This seems to be your only direct
use of buffer heads, which while not deprecated are a bit
of an ugly step child. So if you can easily avoid creating
a buffer_head dependency in a new filesystem I think you
should avoid it. "
As Christoph said [1],
"vm_map_ram is supposed to generally behave better. So if
it doesn't please report that that to the arch maintainer
and linux-mm so that they can look into the issue. Having
user make choices of deep down kernel internals is just
a horrible interface.
Please talk to maintainers of other bits of the kernel
if you see issues and / or need enhancements. "
Let's redo the previous conclusion and kill the vmap
approach.
As Christoph suggested [1], "Please just use plain kmalloc
everywhere and let the normal kernel error injection code
take care of injeting any errors."
As Christoph pointed out [1], "
Why is there __submit_bio which really just obsfucates
what is going on? Also why is __submit_bio using
bio_set_op_attrs instead of opencode it as the comment
right next to it asks you to? "
erofs: kill prio and nofail of erofs_get_meta_page()
As Christoph pointed out [1],
"Why is there __erofs_get_meta_page with the two weird
booleans instead of a single erofs_get_meta_page that
gets and gfp_t for additional flags and an unsigned int
for additional bio op flags."
And since all callers can handle errors, let's kill
prio and nofail and erofs_get_inline_page() now.
As Christoph pointed out [1], "erofs_grab_bio tries to
handle a bio_alloc failure, except that the function will
not actually fail due the mempool backing it."
Sorry about useless code, fix it now and
localize erofs_grab_bio [2].
erofs: use dsb instead of layout for ondisk super_block
As Christoph pointed out [1], "Why is the variable name
for the on-disk subperblock layout? We usually still
calls this something with sb in the name, e.g. dsb.
for disksuper block. " Let's fix it.
Fix as Christoph suggested [1] [2], "remove is_inode_fast_symlink
and just opencode it in the few places using it"
and
"Please just set the ops directly instead of obsfucating that in
a single caller, single line inline function. And please set it
instead of the normal symlink iops in the same place where you
also set those."
As Christoph said, "This looks like a really obsfucated
way to write:
return datamode == EROFS_INODE_FLAT_COMPRESSION ||
datamode == EROFS_INODE_FLAT_COMPRESSION_LEGACY; "
Although I had my own consideration, it's the right way for now.
Merge tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.4 cycle
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
* tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (27 commits)
iio: imu: st_lsm6dsx: rely on IIO_G_TO_M_S_2 for gain definition for LSM9DS1
iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1
iio: cros_ec: set calibscale for 3d MEMS to unit vector
iio: dac: ad5380: fix incorrect assignment to val
iio: imu: st_lsm6dsx: Fix FIFO diff mask for tagged fifo
dt-bindings: iio: imu: st_lsm6dsx: add lsm9ds1 device bindings
iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1
iio: imu: st_lsm6dsx: move register definitions to sensor_settings struct
iio: imu: st_lsm6dsx: introduce update_fifo function pointer
dt-bindings: iio: light: isl29501: Rename bindings documentation file
Kconfig: Fix the reference to the RFD77402 ToF sensor in the 'help' section
iio: st_sensors: Fix build error
dt-bindings: iio: adc: Add AD7606B ADC documentation
dt-bindings: iio: adc: Migrate AD7606 documentation to yaml
MAINTAINERS: Add Beniamin Bia for AD7606 driver
iio: adc: ad7606: Add support for AD7606B ADC
tools: iio: add .gitignore
iio: adc: sc27xx: Change to polling mode to read data
iio: hid-sensor-attributes: Convert to use int_pow()
iio: adc: max1027: Use device-managed APIs
...
Lorenzo Bianconi [Tue, 27 Aug 2019 08:26:35 +0000 (10:26 +0200)]
iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1
Get rid of invalid sensitivity value for LSM9DS1 gyro sensor
Fixes: 52f4b1f19679 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gwendal Grignou [Mon, 26 Aug 2019 23:02:58 +0000 (16:02 -0700)]
iio: cros_ec: set calibscale for 3d MEMS to unit vector
By default, set the calibscale vector to unit vector.
When calibrating one axis, the other axis calibrations are sent as well.
If left to 0, sensor data from uncalibrated axis are zero'ed out until
all axis are calibrated.
Fixes: ed1f2e85da79 ("iio: cros_ec: Add calibscale for 3d MEMS ") Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Colin Ian King [Thu, 15 Aug 2019 11:58:46 +0000 (12:58 +0100)]
iio: dac: ad5380: fix incorrect assignment to val
Currently the pointer val is being incorrectly incremented
instead of the value pointed to by val. Fix this by adding
in the missing * indirection operator.
Addresses-Coverity: ("Unused value") Fixes: c03f2c536818 ("staging:iio:dac: Add AD5380 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: mario tesi <mario.tesi@st.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note the binding is st,lsm9ds1-imu. This device is effectively
two separate devices in the same package. (separate addreses,
chip selects etc) The magnetometer is already supported
as lsm9ds1-mag. imu may not be the best name but it's the best
that anyone has yet come up with for a gyro and accel part.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
accelerometer and gyroscope are not independently clocked. It runs at the gyro
frequencies if both are enabled, see chapter 7.12 of the datasheet.
We could have handled this as a single IIO device but we have split
it up to be more consistent with the other more flexible devices.
Despite supporting and testing the LSM9DS1, we call the gyro channels
iio_chan_spec struct "st_lsm6ds0_gyro_channels" because the register
description is equal. This suggests that supporting LSM6DS0 should be
trivial to do.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Colin Ian King [Fri, 30 Aug 2019 17:50:50 +0000 (18:50 +0100)]
staging: exfat: check for null return from call to FAT_getblk
A call to FAT_getblk is missing a null return check which can
lead to a null pointer dereference. Fix this by adding a null
check to match all the other FAT_getblk return sanity checks.
Addresses-Coverity: ("Dereference null return") Fixes: c48c9f7ff32b ("staging: exfat: add exfat filesystem code to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20190830175050.12706-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Thu, 29 Aug 2019 12:28:39 +0000 (15:28 +0300)]
staging: greybus: light: fix a couple double frees
The problem is in gb_lights_request_handler(). If we get a request to
change the config then we release the light with gb_lights_light_release()
and re-allocated it. However, if the allocation fails part way through
then we call gb_lights_light_release() again. This can lead to a couple
different double frees where we haven't cleared out the original values:
I also made a small change to how we set "light->channels_count = 0;".
The original code handled this part fine and did not cause a use after
free but it was sort of complicated to read.
There are two hunks of code that check if sd30_mode is true however
an earlier check in an outer code block on sd30_mode being false means
that sd30_mode can never be true at these points so these checks are
redundant. Remove the dead code.
Colin Ian King [Mon, 2 Sep 2019 09:40:52 +0000 (10:40 +0100)]
staging: exfat: remove return and error return via a goto
The return statement is incorrect, the error exit should be by
assigning ret with the error code and exiting via label out.
Thanks to Valdis Klētnieks for correcting my original fix.
Colin Ian King [Fri, 30 Aug 2019 18:46:44 +0000 (19:46 +0100)]
staging: exfat: fix uninitialized variable ret
Currently there are error return paths in ffsReadFile that
exit via lable err_out that return and uninitialized error
return in variable ret. Fix this by initializing ret to zero.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: c48c9f7ff32b ("staging: exfat: add exfat filesystem code to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>, Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Link: https://lore.kernel.org/r/20190830184644.15590-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CHECK: Please don't use multiple blank lines
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Please use a blank line after function/struct/union/enum
declarations
This should fix a build error in some configurations when CONFIG_BLOCK
is not selected. Also properly set the dependancy for no FAT support at
the same time.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu> Link: https://lore.kernel.org/r/20190902174631.GB31445@kroah.com Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valdis Klētnieks [Wed, 28 Aug 2019 16:08:17 +0000 (18:08 +0200)]
staging: exfat: add exfat filesystem code to staging
The exfat code needs a lot of work to get it into "real" shape for
the fs/ part of the kernel, so put it into drivers/staging/ for now so
that it can be worked on by everyone in the community.
The full specification of the filesystem can be found at:
https://docs.microsoft.com/en-us/windows/win32/fileio/exfat-specification
iio: imu: st_lsm6dsx: move register definitions to sensor_settings struct
Move some register definitions to the per-device array of struct
st_lsm6dsx_sensor_settings in order to simplify adding new sensor
devices to the driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rui Miguel Silva [Tue, 27 Aug 2019 15:53:02 +0000 (16:53 +0100)]
staging: greybus: add missing includes
Before moving greybus core out of staging and moving header files to
include/linux some greybus header files were missing the necessary
includes. This would trigger compilation faillures with some example
errors logged bellow for with CONFIG_KERNEL_HEADER_TEST=y.
So, add the necessary headers to compile clean before relocating the
header files.
./include/linux/greybus/hd.h:23:50: error: unknown type name 'u16'
int (*cport_disable)(struct gb_host_device *hd, u16 cport_id); ^~~
./include/linux/greybus/greybus_protocols.h:1314:2: error: unknown type name '__u8'
__u8 data[0];
^~~~
./include/linux/greybus/hd.h:24:52: error: unknown type name 'u16'
int (*cport_connected)(struct gb_host_device *hd, u16 cport_id); ^~~
./include/linux/greybus/hd.h:25:48: error: unknown type name 'u16'
int (*cport_flush)(struct gb_host_device *hd, u16 cport_id); ^~~
./include/linux/greybus/hd.h:26:51: error: unknown type name 'u16'
int (*cport_shutdown)(struct gb_host_device *hd, u16 cport_id, ^~~
./include/linux/greybus/hd.h:27:5: error: unknown type name 'u8'
u8 phase, unsigned int timeout);
^~
./include/linux/greybus/hd.h:28:50: error: unknown type name 'u16'
int (*cport_quiesce)(struct gb_host_device *hd, u16 cport_id, ^~~
./include/linux/greybus/hd.h:29:5: error: unknown type name 'size_t'
size_t peer_space, unsigned int timeout);
^~~~~~
./include/linux/greybus/hd.h:29:5: note: 'size_t' is defined in header '<stddef.h>'; did you forget to '#include <stddef.h>'?
./include/linux/greybus/hd.h:1:1:
+#include <stddef.h>
/* SPDX-License-Identifier: GPL-2.0 */
./include/linux/greybus/hd.h:29:5:
size_t peer_space, unsigned int timeout);
^~~~~~
./include/linux/greybus/hd.h:30:48: error: unknown type name 'u16'
int (*cport_clear)(struct gb_host_device *hd, u16 cport_id); ^~~
./include/linux/greybus/hd.h:32:49: error: unknown type name 'u16'
int (*message_send)(struct gb_host_device *hd, u16 dest_cport_id, ^~~
./include/linux/greybus/hd.h:33:32: error: unknown type name 'gfp_t'
struct gb_message *message, gfp_t gfp_mask); ^~~~~
./include/linux/greybus/hd.h:35:55: error: unknown type name 'u16'
int (*latency_tag_enable)(struct gb_host_device *hd, u16 cport_id);
Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Gao Xiang <hsiangkao@aol.com> Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Link: https://lore.kernel.org/r/20190827155302.25704-1-rui.silva@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: greybus: move the greybus core to drivers/greybus
The Greybus core code has been stable for a long time, and has been
shipping for many years in millions of phones. With the advent of a
recent Google Summer of Code project, and a number of new devices in the
works from various companies, it is time to get the core greybus code
out of staging as it really is going to be with us for a while.
staging: greybus: move core include files to include/linux/greybus/
With the goal of moving the core of the greybus code out of staging, the
include files need to be moved to include/linux/greybus.h and
include/linux/greybus/
Cc: Vaibhav Hiremath <hvaibhav.linux@gmail.com> Cc: Johan Hovold <johan@kernel.org> Cc: Vaibhav Agarwal <vaibhav.sr@gmail.com> Cc: Rui Miguel Silva <rmfrfs@gmail.com> Cc: David Lin <dtwlin@gmail.com> Cc: "Bryan O'Donoghue" <pure.logic@nexus-software.ie> Cc: greybus-dev@lists.linaro.org Cc: devel@driverdev.osuosl.org Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Alex Elder <elder@kernel.org> Link: https://lore.kernel.org/r/20190825055429.18547-8-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the greybus drivers were converted to SPDX identifiers for the
license text, some license boilerplate was not removed. Clean this up
by removing this unneeded text now.