Stefan Agner [Thu, 12 Jul 2018 08:07:24 +0000 (10:07 +0200)]
mmc: sdhci-esdhc-imx: disable clocks before changing frequency
In the uSDHC case (e.g. i.MX 6) clocks only get disabled if frequency
is set to 0. However, it could be that the stack asks for a frequency
change while clocks are on. In that case the function clears the
divider registers (by clearing ESDHC_CLOCK_MASK) while the clock is
enabled! This causes a short period of time where the clock is
undivided (on a i.MX 6DL a clock of 196MHz has been measured).
For older IP variants the driver disables clock by clearing some bits
in ESDHC_SYSTEM_CONTROL.
Make sure to disable card clock before changing frequency for uSDHC
IP variants too.
Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stefan Agner [Thu, 12 Jul 2018 07:39:04 +0000 (09:39 +0200)]
mmc: tegra: prevent ACMD23 on Tegra 3
It seems that SD3.0 advertisement needs to be set for higher eMMC
speed modes (namely DDR52) as well. The TRM states that the SD3.0
advertisement bit should be set for all controller instances, even
for those not supporting UHS-I mode...
When specifying vqmmc-supply as a fixed 1.8V regulator on a Tegra
SD/MMC instance which is connected to a eMMC device, the stack
enables SD3.0. However, enabling it has consequences: If SDHCI 3.0
support is advertised the stack enables Auto-CMD23. Unfortunately
Auto-CMD23 seems not to work well with Tegra 3 currently. It leads
to regular warnings:
mmc2: Got command interrupt 0x00010000 even though no command operation was in progress.
It is not entirely clear why those errors happens. It seems that
a Linux 3.1 based downstream kernel which has Auto-CMD23 support
does not show those warnings.
Use quirk SDHCI_QUIRK2_ACMD23_BROKEN to prevent Auto-CMD23 being
used for now. With this the eMMC works stable on high-speed mode
while still announcing SD3.0.
This allows to use mmc-ddr-1_8v to enables DDR52 mode. In DDR52
mode read speed improves from about 42MiB/s to 72MiB/s on an
Apalis T30.
Stefan Agner [Thu, 12 Jul 2018 07:39:02 +0000 (09:39 +0200)]
mmc: tegra: prevent HS200 on Tegra 3
The stack assumes that SDHC controller which support SD3.0 (SDR104) do
support HS200. This is not the case for Tegra 3, which does support SD
3.0
but only supports eMMC spec 4.41.
Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not
support HS200.
Note that commit 156e14b126ff ("mmc: sdhci: fix caps2 for HS200") added
the tie between SD3.0 (SDR104) and HS200. I don't think that this is
necessarly true. It is fully legitimate to support SD3.0 and not support
HS200. The quirk naming suggests something is broken in the controller,
but this is not the case: The controller simply does not support HS200.
mmc: sdhci-pci-dwc-mshc: synopsys dwc mshc support
Synopsys has DWC MSHC controller on HPAS-DX platform connected using PCIe
interface with SD card slot and eMMC device slots. This patch is to
enable SD cards connected on this platform. As Clock generation logic
is implemented using MMCM module of HAPS-DX platform, we have separate
functions to control the MMCM to generate required clocks with respect
to speed mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stefan Agner [Thu, 5 Jul 2018 12:18:19 +0000 (14:18 +0200)]
mmc: sdhci: do not try to use 3.3V signaling if not supported
For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
mmc1: Switching to 3.3V signalling voltage failed
Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips
SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Daniel Mack [Tue, 3 Jul 2018 20:10:26 +0000 (22:10 +0200)]
mmc: pxamci: make GPIO lookups from pdata optional
A recent commit introduced a call to mmc_of_parse() and removed the
explicit assignment of GPIOs in the pdata structure. This will leave
them set to 0, which is a valid GPIO per se, so the code that looks
at these members will try to allocate them and fail.
To fix this properly, make the following changes:
a) Refrain from allocating and assiging a pdata struct from
pxamci_of_init(). It's a hack to do it this way anyway.
Instead, move the only remaining member of interest in
'struct pxamci_host' and assign the value from either
the passed in pdata pointer or with the value read from DT.
b) Let the only user of 'detect_delay_ms' look at the member of
'struct pxamci_host', not the pdata.
c) Make more code in pxamci_probe() dependent on the presence of
actual pdata.
This will also ease the removal of pdata one day.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Mack [Sat, 30 Jun 2018 18:14:04 +0000 (20:14 +0200)]
mmc: pxamci: remove pxa-mmc, gpio-power from devicetree bindings
Devicetree-enabled boards should use proper regulators to control the
power of cards, not GPIOs, so let's remove this property. The regulator
properties are supported by the MMC core and are described in the
generic MMC document:
Documentation/devicetree/bindings/mmc/mmc.txt
Note that devicetree support for PXA platforms hasn't fully landed yet,
so this binding does not have any users at this point.
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Mack [Sat, 30 Jun 2018 18:14:03 +0000 (20:14 +0200)]
mmc: pxamci: call mmc_of_parse()
Call into mmc_of_parse() from pxamci_of_init(). As it needs a pointer to a
struct mmc_host, refactor the code a bit.
This allows all generic MMC properties to be set that are described in
Documentation/devicetree/bindings/mmc/mmc.txt. Reword the documentation
a bit to make that clear.
The "cd" and "wp" gpio lookups are removed as the lookup will now be
done by mmc_of_parse().
Signed-off-by: Daniel Mack <daniel@zonque.org> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 26 Jun 2018 14:51:31 +0000 (16:51 +0200)]
mmc: core: Drop the unused mmc_power_save|restore_host()
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
yinbo.zhu [Mon, 25 Jun 2018 08:46:24 +0000 (16:46 +0800)]
mmc: sdhci-of-esdhc: modify the sd clock in of_match_node way
Convert to use of_match_node method to fix up eSDHC clock for
ls1046a/ls1012a/p1010. Also add eSDHC clock fixup for ls1021a
according to its datasheet. The maxmum speed for ls1021a eSDHC
high speed mode is 46.5MHz.
Helmut Grohne [Wed, 20 Jun 2018 11:33:00 +0000 (13:33 +0200)]
mmc: sdhci-of-arasan: Add quirk for unstable clocks
Some controllers immediately report SDHCI_CLOCK_INT_STABLE after
enabling the clock even when the clock is not stable. When used in
conjunction with older/slower cards, this can result in:
mmc0: error -84 whilst initialising SD card
When the stable reporting is known to be broken, we simply wait for the
maximum stabilization period.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Helmut Grohne [Wed, 20 Jun 2018 11:32:51 +0000 (13:32 +0200)]
dt-bindings: mmc: broken clock stable indicator on arasan controllers
Some controllers immediately report that their internal clock is stable
after activating it even when the clock is not stable. When used in
conjunction with older/slower cards, this can result in:
mmc0: error -84 whilst initialising SD card
This flag allows documenting and thus working around such a hardware
defect.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vijay Viswanath [Tue, 19 Jun 2018 05:39:19 +0000 (11:09 +0530)]
mmc: sdhci-msm: Add msm version specific ops and data structures
In addition to offsets of certain registers changing, the registers in
core_mem have been shifted to HC mem as well. To access these
registers, define msm version specific functions. These functions can
be loaded into the function pointers at the time of probe based on
the msm version detected.
Also defind new data structure to hold version specific Ops and
register addresses.
Sayali Lokhande [Tue, 19 Jun 2018 05:39:18 +0000 (11:09 +0530)]
mmc: sdhci-msm: Define new Register address map
For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org> Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org> Reviewed-by: Evan Green <evgreen@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simon Horman [Mon, 18 Jun 2018 12:57:49 +0000 (14:57 +0200)]
mmc: core: more fine-grained hooks for HS400 tuning
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete
These supplement the existing HS400 operation:
* prepare_hs400_tuning
This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
This can be done in an implementation of complete_hs400_tuning
If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marek Szyprowski [Tue, 12 Jun 2018 10:55:23 +0000 (12:55 +0200)]
mmc: dw_mmc-exynos: fix potential external abort in resume_noirq()
dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Aapo Vienamo [Mon, 4 Jun 2018 15:35:40 +0000 (18:35 +0300)]
mmc: tegra: Use sdhci_pltfm_clk_get_max_clock
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Shawn Lin [Wed, 30 May 2018 02:11:43 +0000 (10:11 +0800)]
mmc: core: Adjust and reuse the macro of R1_STATUS(x)
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- A fix for OMAP5 and DRA7 to make the branch predictor hardening
settings take proper effect on secondary cores
- Disable USB OTG on am3517 since current driver isn't working
- Fix thermal sensor register settings on Armada 38x
- Fix suspend/resume IRQs on pxa3xx
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
ARM: dts: armada-38x: use the new thermal binding
Merge tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
Olof Johansson [Sat, 14 Jul 2018 22:14:02 +0000 (15:14 -0700)]
Merge tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Merge tag 'for-linus-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two related fixes for a boot failure of Xen PV guests"
* tag 'for-linus-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: setup pv irq ops vector earlier
xen: remove global bit from __default_kernel_pte_mask for pv guests
* emailed patches form Andrew Morton <akpm@linux-foundation.org>:
reiserfs: fix buffer overflow with long warning messages
checkpatch: fix duplicate invalid vsprintf pointer extension '%p<foo>' messages
mm: do not bug_on on incorrect length in __mm_populate()
mm/memblock.c: do not complain about top-down allocations for !MEMORY_HOTREMOVE
fs, elf: make sure to page align bss in load_elf_library
x86/purgatory: add missing FORCE to Makefile target
net/9p/client.c: put refcount of trans_mod in error case in parse_opts()
mm: allow arch to supply p??_free_tlb functions
autofs: fix slab out of bounds read in getname_kernel()
fs/proc/task_mmu.c: fix Locked field in /proc/pid/smaps*
mm: do not drop unused pages when userfaultd is running
Eric Biggers [Fri, 13 Jul 2018 23:59:27 +0000 (16:59 -0700)]
reiserfs: fix buffer overflow with long warning messages
ReiserFS prepares log messages into a 1024-byte buffer with no bounds
checks. Long messages, such as the "unknown mount option" warning when
userspace passes a crafted mount options string, overflow this buffer.
This causes KASAN to report a global-out-of-bounds write.
Fix it by truncating messages to the buffer size.
Link: http://lkml.kernel.org/r/20180707203621.30922-1-ebiggers3@gmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+b890b3335a4d8c608963@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason is that the length of the new brk is not page aligned when we
try to populate the it. There is no reason to bug on that though.
do_brk_flags already aligns the length properly so the mapping is
expanded as it should. All we need is to tell mm_populate about it.
Besides that there is absolutely no reason to to bug_on in the first
place. The worst thing that could happen is that the last page wouldn't
get populated and that is far from putting system into an inconsistent
state.
Fix the issue by moving the length sanitization code from do_brk_flags
up to vm_brk_flags. The only other caller of do_brk_flags is brk
syscall entry and it makes sure to provide the proper length so t here
is no need for sanitation and so we can use do_brk_flags without it.
Also remove the bogus BUG_ONs.
[osalvador@techadventures.net: fix up vm_brk_flags s@request@len@] Link: http://lkml.kernel.org/r/20180706090217.GI32658@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: syzbot <syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 13 Jul 2018 23:59:16 +0000 (16:59 -0700)]
mm/memblock.c: do not complain about top-down allocations for !MEMORY_HOTREMOVE
Mike Rapoport is converting architectures from bootmem to nobootmem
allocator. While doing so for m68k Geert has noticed that he gets a
scary looking warning:
The warning is basically saying that a top-down allocation can break
memory hotremove because memblock allocation is not movable. But m68k
doesn't even support MEMORY_HOTREMOVE so there is no point to warn about
it.
Make the warning conditional only to configurations that care.
Link: http://lkml.kernel.org/r/20180706061750.GH32658@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Sam Creasey <sammy@sammy.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oscar Salvador [Fri, 13 Jul 2018 23:59:13 +0000 (16:59 -0700)]
fs, elf: make sure to page align bss in load_elf_library
The current code does not make sure to page align bss before calling
vm_brk(), and this can lead to a VM_BUG_ON() in __mm_populate() due to
the requested lenght not being correctly aligned.
Let us make sure to align it properly.
Kees: only applicable to CONFIG_USELIB kernels: 32-bit and configured
for libc5.
Link: http://lkml.kernel.org/r/20180705145539.9627-1-osalvador@techadventures.net Signed-off-by: Oscar Salvador <osalvador@suse.de> Reported-by: syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Acked-by: Kees Cook <keescook@chromium.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Rudo [Fri, 13 Jul 2018 23:59:09 +0000 (16:59 -0700)]
x86/purgatory: add missing FORCE to Makefile target
- Build the kernel without the fix
- Add some flag to the purgatories KBUILD_CFLAGS,I used
-fno-asynchronous-unwind-tables
- Re-build the kernel
When you look at makes output you see that sha256.o is not re-build in the
last step. Also readelf -S still shows the .eh_frame section for
sha256.o.
With the fix sha256.o is rebuilt in the last step.
Without FORCE make does not detect changes only made to the command line
options. So object files might not be re-built even when they should be.
Fix this by adding FORCE where it is missing.
Link: http://lkml.kernel.org/r/20180704110044.29279-2-prudo@linux.ibm.com Fixes: df6f2801f511 ("kernel/kexec_file.c: move purgatories sha256 to common code") Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Acked-by: Dave Young <dyoung@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> [4.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/9p/client.c: put refcount of trans_mod in error case in parse_opts()
In my testing, the second mount will fail after umounting successfully.
The reason is that we put refcount of trans_mod in the correct case
rather than the error case in parse_opts() at last. That will cause the
refcount decrease to -1, and when we try to get trans_mod again in
try_module_get(), we could only increase refcount to 0 which will cause
failure as follows:
parse_opts
v9fs_get_trans_by_name
try_module_get : return NULL to caller which cause error
So we should put refcount of trans_mod in error case.
Link: http://lkml.kernel.org/r/5B3F39A0.2030509@huawei.com Fixes: 9421c3e64137ec ("net/9p/client.c: fix potential refcnt problem of trans module") Signed-off-by: Jun Piao <piaojun@huawei.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Dominique Martinet <dominique.martinet@cea.fr> Tested-by: Dominique Martinet <dominique.martinet@cea.fr> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicholas Piggin [Fri, 13 Jul 2018 23:59:03 +0000 (16:59 -0700)]
mm: allow arch to supply p??_free_tlb functions
The mmu_gather APIs keep track of the invalidated address range
including the span covered by invalidated page table pages. Ranges
covered by page tables but not ptes (and therefore no TLBs) still need
to be invalidated because some architectures (x86) can cache
intermediate page table entries, and invalidate those with normal TLB
invalidation instructions to be almost-backward-compatible.
Architectures which don't cache intermediate page table entries, or
which invalidate these caches separately from TLB invalidation, do not
require TLB invalidation range expanded over page tables.
Allow architectures to supply their own p??_free_tlb functions, which
can avoid the __tlb_adjust_range.
Link: http://lkml.kernel.org/r/20180703013131.2807-1-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: "Aneesh Kumar K. V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Nadav Amit <nadav.amit@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomas Bortoli [Fri, 13 Jul 2018 23:58:59 +0000 (16:58 -0700)]
autofs: fix slab out of bounds read in getname_kernel()
The autofs subsystem does not check that the "path" parameter is present
for all cases where it is required when it is passed in via the "param"
struct.
In particular it isn't checked for the AUTOFS_DEV_IOCTL_OPENMOUNT_CMD
ioctl command.
To solve it, modify validate_dev_ioctl(function to check that a path has
been provided for ioctl commands that require it.
Link: http://lkml.kernel.org/r/153060031527.26631.18306637892746301555.stgit@pluto.themaw.net Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: syzbot+60c837b428dc84e83a93@syzkaller.appspotmail.com Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs/proc/task_mmu.c: fix Locked field in /proc/pid/smaps*
Thomas reports:
"While looking around in /proc on my v4.14.52 system I noticed that all
processes got a lot of "Locked" memory in /proc/*/smaps. A lot more
memory than a regular user can usually lock with mlock().
Commit 493b0e9d945f (in v4.14-rc1) seems to have changed the behavior
of "Locked".
Before that commit the code was like this. Notice the VM_LOCKED check.
mm: do not drop unused pages when userfaultd is running
KVM guests on s390 can notify the host of unused pages. This can result
in pte_unused callbacks to be true for KVM guest memory.
If a page is unused (checked with pte_unused) we might drop this page
instead of paging it. This can have side-effects on userfaultd, when
the page in question was already migrated:
The next access of that page will trigger a fault and a user fault
instead of faulting in a new and empty zero page. As QEMU does not
expect a userfault on an already migrated page this migration will fail.
The most straightforward solution is to ignore the pte_unused hint if a
userfault context is active for this VMA.
Link: http://lkml.kernel.org/r/20180703171854.63981-1-borntraeger@de.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Janosch Frank <frankja@linux.ibm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Cornelia Huck <cohuck@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus, also saw this bug on his machine, and confirmed that reverting
commit 124049decbb1 ("x86/e820: put !E820_TYPE_RAM regions into
memblock.reserved") fixes the issue.
The problem is that we incorrectly zero some struct pages after they
were setup.
The fix is to zero unavailable struct pages prior to initializing of
struct pages.
A more detailed fix should come later that would avoid double zeroing
cases: one in __init_single_page(), the other one in
zero_resv_unavail().
Fixes: 124049decbb1 ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved") Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar:
"Misc tooling fixes: python3 related fixes, gcc8 fix, bashism fixes and
some other smaller fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Use python-config --includes rather than --cflags
perf script python: Fix dict reference counting
perf stat: Fix --interval_clear option
perf tools: Fix compilation errors on gcc8
perf test shell: Prevent temporary editor files from being considered test scripts
perf llvm-utils: Remove bashism from kernel include fetch script
perf test shell: Make perf's inet_pton test more portable
perf test shell: Replace '|&' with '2>&1 |' to work with more shells
perf scripts python: Add Python 3 support to EventClass.py
perf scripts python: Add Python 3 support to sched-migration.py
perf scripts python: Add Python 3 support to Util.py
perf scripts python: Add Python 3 support to SchedGui.py
perf scripts python: Add Python 3 support to Core.py
perf tools: Generate a Python script compatible with Python 2 and 3
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Ingo Molnar:
"Various rseq ABI fixes and cleanups: use get_user()/put_user(),
validate parameters and use proper uapi types, etc"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq/selftests: cleanup: Update comment above rseq_prepare_unload
rseq: Remove unused types_32_64.h uapi header
rseq: uapi: Declare rseq_cs field as union, update includes
rseq: uapi: Update uapi comments
rseq: Use get_user/put_user rather than __get_user/__put_user
rseq: Use __u64 for rseq_cs fields, validate user inputs
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
Merge tag 'kbuild-fixes-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- update Kbuild and Kconfig documents
- sanitize -I compiler option handling
- update extract-vmlinux script to recognize LZ4 and ZSTD
- fix tools Makefiles
- update tags.sh to handle __ro_after_init
- suppress warnings in case getconf does not recognize LFS_* parameters
* tag 'kbuild-fixes-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: suppress warnings from 'getconf LFS_*'
scripts/tags.sh: add __ro_after_init
tools: build: Use HOSTLDFLAGS with fixdep
tools: build: Fixup host c flags
tools build: fix # escaping in .cmd files for future Make
scripts: teach extract-vmlinux about LZ4 and ZSTD
kbuild: remove duplicated comments about PHONY
kbuild: .PHONY is not a variable, but PHONY is
kbuild: do not drop -I without parameter
kbuild: document the KBUILD_KCONFIG env. variable
kconfig: update user kconfig tools doc.
kbuild: delete INSTALL_FW_PATH from kbuild documentation
kbuild: update ARCH alias info for sparc
kbuild: update ARCH alias info for sh
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Catalin's out enjoying the sunshine, so I'm sending the fixes for a
couple of weeks (although there hopefully won't be any more!).
We've got a revert of a previous fix because it broke the build with
some distro toolchains and a preemption fix when detemining whether or
not the SIMD unit is in use.
Summary:
- Revert back to the 'linux' target for LD, as 'elf' breaks some
distributions
- Fix preemption race when testing whether the vector unit is in use
or not"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: neon: Fix function may_use_simd() return error status
Revert "arm64: Use aarch64elf and aarch64elfb emulation mode variants"
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A couple of small fixes this time around from Steven for an
interaction between ftrace and kernel read-only protection, and
Vladimir for nommu"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
ARM: 8775/1: NOMMU: Use instr_sync instead of plain isb in common code
Merge tag 'trace-v4.18-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixlet from Steven Rostedt:
"Joel Fernandes asked to add a feature in tracing that Android had its
own patch internally for. I took it back in 4.13. Now he realizes that
he had a mistake, and swapped the values from what Android had. This
means that the old Android tools will break when using a new kernel
that has the new feature on it.
The options are:
1. To swap it back to what Android wants.
2. Add a command line option or something to do the swap
3. Just let Android carry a patch that swaps it back
Since it requires setting a tracing option to enable this anyway, I
doubt there are other users of this than Android. Thus, I've decided
to take option 1. If someone else is actually depending on the order
that is in the kernel, then we will have to revert this change and go
to option 2 or 3"
* tag 'trace-v4.18-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Reorder display of TGID to be after PID
Merge tag 'sound-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few HD-auio fixes: one fix for a possible mutex deadlock at
HDMI hotplug handling is somewhat subtle and delicate, while the rest
are usual device-specific quirks"
* tag 'sound-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132: Update a pci quirk device name
ALSA: hda/ca0132: Add Recon3Di quirk for Gigabyte G1.Sniper Z97
ALSA: hda/realtek - two more lenovo models need fixup of MIC_LOCATION
ALSA: hda - Handle pm failure during hotplug
Merge tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
However Android's trace visualization tools expect a slightly different
format due to an out-of-tree patch patch that was been carried for a
decade, notice that the TGID and CPU fields are reversed:
From kernel v4.13 onwards, during which TGID was introduced, tracing
with systrace on all Android kernels will break (most Android kernels
have been on 4.9 with Android patches, so this issues hasn't been seen
yet). From v4.13 onwards things will break.
The chrome browser's tracing tools also embed the systrace viewer which
uses the legacy TGID format and updates to that are known to be
difficult to make.
Considering this, I suggest we make this change to the upstream kernel
and backport it to all Android kernels. I believe this feature is merged
recently enough into the upstream kernel that it shouldn't be a problem.
Also logically, IMO it makes more sense to group the TGID with the
TASK-PID and the CPU after these.
Link: http://lkml.kernel.org/r/20180626000822.113931-1-joel@joelfernandes.org Cc: jreck@google.com Cc: tkjos@google.com Cc: stable@vger.kernel.org Fixes: 441dae8f2f29 ("tracing: Add support for display of tgid in trace output") Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Wolfram Sang [Tue, 10 Jul 2018 21:42:15 +0000 (23:42 +0200)]
i2c: recovery: if possible send STOP with recovery pulses
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Suppress warnings for systems that do not recognize LFS_*.
getconf: no such configuration parameter `LFS_CFLAGS'
getconf: no such configuration parameter `LFS_LDFLAGS'
getconf: no such configuration parameter `LFS_LIBS'
Fixes: d7f14c66c273 ("kbuild: Enable Large File Support for hostprogs") Reported-by: Chen Feng <puck.chen@hisilicon.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Laura Abbott [Tue, 10 Jul 2018 00:45:56 +0000 (17:45 -0700)]
tools: build: Fixup host c flags
Commit 0c3b7e42616f ("tools build: Add support for host programs format")
introduced host_c_flags which referenced CHOSTFLAGS. The actual name of the
variable is HOSTCFLAGS. Fix this up.
Fixes: 0c3b7e42616f ("tools build: Add support for host programs format") Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adam Ford [Wed, 11 Jul 2018 17:54:54 +0000 (12:54 -0500)]
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
xen: remove global bit from __default_kernel_pte_mask for pv guests
When removing the global bit from __supported_pte_mask do the same for
__default_kernel_pte_mask in order to avoid the WARN_ONCE() in
check_pgprot() when setting a kernel pte before having called
init_mem_mapping().
Cc: <stable@vger.kernel.org> # 4.17 Reported-by: Michael Young <m.a.young@durham.ac.uk> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
Dynamic ftrace requires modifying the code segments that are usually
set to read-only. To do this, a per arch function is called both before
and after the ftrace modifications are performed. The "before" function
will set kernel code text to read-write to allow for ftrace to make the
modifications, and the "after" function will set the kernel code text
back to "read-only" to keep the kernel code text protected.
The issue happens when dynamic ftrace is tested at boot up. The test is
done before the kernel code text has been set to read-only. But the
"before" and "after" calls are still performed. The "after" call will
change the kernel code text to read-only prematurely, and other boot
code that expects this code to be read-write will fail.
The solution is to add a variable that is set when the kernel code text
is expected to be converted to read-only, and make the ftrace "before"
and "after" calls do nothing if that variable is not yet set. This is
similar to the x86 solution from commit 162396309745 ("ftrace, x86:
make kernel text writable only for conversions").
Link: http://lkml.kernel.org/r/20180620212906.24b7b66e@vmware.local.home Reported-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Kamal Heib [Tue, 10 Jul 2018 08:56:50 +0000 (11:56 +0300)]
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
Fix memory leak in the error path of mlx5_ib_create_srq() by making sure
to free the allocated srq.
Fixes: c2b37f76485f ("IB/mlx5: Fix integer overflows in mlx5_ib_create_srq") Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Acked-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Merge branch 'for-4.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
- Jens's patches to expand the usable command depth from 31 to 32 broke
sata_fsl due to a subtle command iteration bug. Fixed by introducing
explicit iteration helpers and using the correct variant.
- On some laptops, enabling LPM by default reportedly led to occasional
hard hangs. Blacklist the affected cases.
- Other misc fixes / changes.
* 'for-4.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: Remove depends on HAS_DMA in case of platform dependency
ata: Fix ZBC_OUT all bit handling
ata: Fix ZBC_OUT command block check
ahci: Add Intel Ice Lake LP PCI ID
ahci: Disable LPM on Lenovo 50 series laptops with a too old BIOS
sata_nv: remove redundant pointers sdev0 and sdev1
sata_fsl: remove dead code in tag retrieval
sata_fsl: convert to command iterator
libata: convert eh to command iterators
libata: add command iterator helpers
ata: ahci_mvebu: ahci_mvebu_stop_engine() can be static
libahci: Fix possible Spectre-v1 pmp indexing in ahci_led_store()
sample: vfio-mdev: avoid deadlock in mdev_access()
mdev_access() calls mbochs_get_page() with mdev_state->ops_lock held,
while mbochs_get_page() locks the mutex by itself.
It leads to unavoidable deadlock.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Merge tag 'char-misc-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few char/misc driver fixes for 4.18-rc5.
The "largest" stuff here is fixes for the UIO changes in 4.18-rc1 that
caused breakages for some people. Thanks to Xiubo Li for fixing them
quickly. Other than that, minor fixes for thunderbolt, vmw_balloon,
nvmem, mei, ibmasm, and mei drivers. There's also a MAINTAINERS update
where Rafael is offering to help out with reviewing driver core
patches.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: Don't let a NULL cell_id for nvmem_cell_get() crash us
thunderbolt: Notify userspace when boot_acl is changed
uio: fix crash after the device is unregistered
uio: change to use the mutex lock instead of the spin lock
uio: use request_threaded_irq instead
fpga: altera-cvp: Fix an error handling path in 'altera_cvp_probe()'
ibmasm: don't write out of bounds in read handler
MAINTAINERS: Add myself as driver core changes reviewer
mei: discard messages from not connected client during power down.
vmw_balloon: fix inflation with batching