Rahul Tanwar [Thu, 8 Aug 2019 10:02:07 +0000 (18:02 +0800)]
serial: lantiq: Make IRQ & ISR assignment dynamic
This driver/IP is reused across multiple SoCs. Older SoCs supported three
separate IRQs for tx, rx & err interrupts. Newer Lightning Mountain SoC
supports single IRQ for all of tx/rx/err interrupts. This patch modifies
the driver design to support dynamic assignment of IRQ resources & ISRs
based on devicetree node compatible entries.
Rahul Tanwar [Thu, 8 Aug 2019 10:02:06 +0000 (18:02 +0800)]
serial: lantiq: Use proper DT compatible string
Use explicit string instead of a macro for devicetree compatible string.
This series of patches is to add support for multiple SoCs which reuse the same
serial controller IP. The following patches will add another compatible string
to support new Lightning Mountain(LGM) SoC. So it makes sense to have the
compatible strings explicitly mentioned instead of a fixed macro.
Andy Shevchenko [Tue, 6 Aug 2019 09:43:22 +0000 (12:43 +0300)]
serial: 8250_lpss: Enable HS UART on Elkhart Lake
Intel Elkhart Lake may use High Speed UART from OSE IP block.
This is different to what we have in main LPSS, though compatible
with older version of it, which is handled by this driver.
Enable OSE HS UART on Intel Elkhart Lake by adding PCI IDs.
Andy Shevchenko [Tue, 6 Aug 2019 09:43:19 +0000 (12:43 +0300)]
serial: 8250_lpss: add fractional divisor support
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups specific get_divisor() and set_divisor() hook.
Among other changes the FIFO size is now retrieved from the hardware.
Andy Shevchenko [Tue, 6 Aug 2019 09:43:16 +0000 (12:43 +0300)]
serial: 8250_dw: split Synopsys DesignWare 8250 common functions
We would like to use same functions in the couple of drivers for
Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand
library module which users will select explicitly.
Andy Shevchenko [Tue, 6 Aug 2019 09:43:14 +0000 (12:43 +0300)]
serial: 8250_dw: Use a unified new dev variable in remove
The commit 2cb78eab2376 ("serial: 8250_dw: Use a unified new dev variable in
probe") introduced a local dev variable in ->probe(). Do the same in ->remove()
in order to prepare for sequential patches.
Rahul Tanwar [Wed, 7 Aug 2019 09:21:31 +0000 (17:21 +0800)]
serial: lantiq: Add SMP support
The existing driver can only support single core SoC. But new multicore
platforms which reuse the same driver/IP need SMP support. This patch adds
multicore support in the driver.
Andrey Smirnov [Mon, 5 Aug 2019 18:57:01 +0000 (11:57 -0700)]
tty: serial: fsl_lpuart: Ignore TX/RX interrupts if DMA is enabled
In a mixed DMA/IRQ use-case (e.g.: DMA for TX, IRQ for RX), interrupt
handler might try to handle Rx/Tx condition it shouldn't. Change the
code to only handle TX/RX event if corresponding path isn't being
handled by DMA.
Andrey Smirnov [Mon, 5 Aug 2019 18:57:00 +0000 (11:57 -0700)]
tty: serial: fsl_lpuart: Don't enable TIE in .startup() or .resume()
Enabling TIE in .startup() callback causes the driver to start (or at
least try) to transmit data before .start_tx() is called. Which, while
harmless (since TIE handler will immediately disable it), is a no-op
and shouldn't really happen. Drop UARTCR2_TIE from list of bits set in
lpuart_startup().
This change will also not enable TIE in .resume(), but it seems that,
similart to .startup(), transmit interrupt shouldn't be enabled there
either.
Most users of lpuart*_setup_watermark() enable identical set of flags
right after the call, so combine those two action into a subroutine
and make use of it.
Code configure DMA TX path in lpuart_startup(), lpuart32_startup() and
lpuart_resume() is doing exactly the same thing, so move it into a
standalone subroutine.
serial: mctrl_gpio: Avoid probe failures in case of missing gpiolib
If CONFIG_GPIOLIB is not enabled, mctrl_gpio_init() and
mctrl_gpio_init_noauto() will currently return an error pointer with
-ENOSYS. As the mctrl GPIOs are usually optional, drivers need to
check for this condition to allow continue probing.
To avoid the need for this check in each driver, we return NULL
instead, as all the mctrl_gpio_*() functions are skipped anyway.
We also adapt mctrl_gpio_to_gpiod() to be in line with this change.
Aaron Sierra [Thu, 1 Aug 2019 18:59:56 +0000 (13:59 -0500)]
serial: 8250_exar: Absorb remaining 8250_port INT0 support
Move INT0 clearing out of common, per-port serial8250_do_startup()
into PCI device probe/resume.
As described in commit 2c0ac5b48a35 ("serial: exar: Fix stuck MSIs"),
the purpose of clearing INT0 is to prevent the PCI interrupt line from
becoming stuck asserted, "which is fatal with edge-triggered MSIs".
Like the clearing via interrupt handler that moved from common code in
commit c7e1b4059075 ("tty: serial: exar: Relocate sleep wake-up
handling"), this clearing at startup can be better handled at the PCI
device level.
Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190801185956.3222-1-asierra@xes-inc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: Use DEVICE_ATTR_RW() for rx_fifo_trigger
While commit b6b996b6cdeecf7e ("treewide: Use DEVICE_ATTR_RW") converted
the rx_fifo_timeout attribute, it forgot to convert rx_fifo_trigger due
to a slightly different function naming.
Vivek Gautam [Thu, 1 Aug 2019 12:11:53 +0000 (17:41 +0530)]
tty: serial: qcom_geni_serial: Update the oversampling rate
For QUP IP versions 2.5 and above the oversampling rate is halved
from 32 to 16. Update this rate after reading hardware version
register, so that the clock divider value is correctly set to
achieve required baud rate.
When closing and shutting down the exar serial port, if the chip
has not finished sending all of the data in its buffer, the
remaining bytes will be lost. Hold off on the shutdown until the
bytes have all been sent.
Andy Shevchenko [Wed, 31 Jul 2019 17:05:58 +0000 (20:05 +0300)]
serial: 8250_exar: Move custom divisor support out from 8250_port
There are Exar custom divisor support in 8250_port which belongs to
8250_exar module. Move it out to the correct module and do not contaminate
generic code with it.
Cc: Aaron Sierra <asierra@xes-inc.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190731170558.52897-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Wed, 31 Jul 2019 17:05:57 +0000 (20:05 +0300)]
serial: 8250_exar: Extract PM routine from 8250_port
There are Exar quirks in 8250_port which belong to 8250_exar module.
Extract PM routine to the correct module and do not contaminate generic code
with it.
Cc: Aaron Sierra <asierra@xes-inc.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20190731170558.52897-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: sh-sci: use driver core functions, not sysfs ones.
This is a driver, do not call "raw" sysfs functions, instead call driver
core ones. Specifically convert the use of sysfs_create_file() and
sysfs_remove_file() to use device_create_file() and device_remove_file()
Stephen Rothwell [Wed, 31 Jul 2019 06:05:57 +0000 (16:05 +1000)]
xilinx_uartps.c: suppress "may be used uninitialised" warning
A powerpc allyesconfig build produces this warning:
In file included from include/linux/radix-tree.h:16,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/device.h:16,
from include/linux/platform_device.h:13,
from drivers/tty/serial/xilinx_uartps.c:16:
drivers/tty/serial/xilinx_uartps.c: In function 'cdns_uart_console_write':
include/linux/spinlock.h:288:3: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
_raw_spin_unlock_irqrestore(lock, flags); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/xilinx_uartps.c:1197:16: note: 'flags' was declared here
unsigned long flags;
^~~~~
It looks like gcc just can't track the relationship between "locked"
and "flags", and it is obvious that "flags" won't be used when "locked"
is zero, so the simplest thing is to initialise flags.
Cc: Jiri Slaby <jslaby@suse.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/r/20190731160557.6a09c3e1@canb.auug.org.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Tue, 30 Jul 2019 18:15:44 +0000 (11:15 -0700)]
tty: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
tty: serial: fsl_lpuart: Drop unnecessary lpuart*_stop_tx()
By the time lpuart_shutdown() calls lpuart_stop_tx() UARTCR2_TE and
UARTCR2_TIE (which the latter will clear) are already cleared, so that
function call should effectively be a no-op. Moreso, lpuart_stop_tx()
is expected to be executed with port spinlock held, which the caller
doesn't. Given all that, drop the call to lpuart_stop_tx() in
lpuart_shutdown().
In case of lpuart32_shutdown()/lpuart32_stop_tx(), TIE won't even be
set if lpuart_dma_tx_use is true. Drop it there as well.
tty: serial: fsl_lpuart: Use cpu_relax() instead of barrier()
Use cpu_relax() instead of barrier() in a tight polling loops to make
them a bit more idiomatic. Should also improve things on ARM64 a bit
since cpu_relax() will expand into "yield" instruction there.
tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs
When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.
Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: fsl_lpuart: Drop no-op bit opearation
The check for termios->c_cflag & CRTSCTS ensure that if we reach else
branch, CRTSCTS in termios->c_cflag is already going to be
cleard. Doing so explicitly there is not necessary. Drop it.
tty: serial: fls_lpuart: Split shared TX IRQ handler into two
While sharing code for Tx interrupt handler between 8 and 32 bit
variant of the peripheral saves a bit of code duplication it also adds
quite a number of lpuart_is_32() checks which makes it harder to
understand. Move shared bits back into corresponding
lpuart*_transmit_buffer functions, split lpuart_txint into
lpuart_txint and lpuart32_txint so we can drop all extra
lpuart_is_32() check and make the code flow more linear.
tty: serial: fsl_lpuart: Fix issue in software flow control
Although I haven't observed this bug in practice, it seems that the
code for handling x_char of LPUART is pretty much identical to that of
i.MX. So the fix found in commit 7e2fb5aa8d81 ("serial: imx: Fix issue
in software flow control"):
serial: imx: Fix issue in software flow control
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
should apply here as well.
tty: serial: fsl_lpuart: Drop unnecessary uart_write_wakeup()
Uart_write_wakeup() will already be called as a part of
lpuart*_transmit_buffer() call, so there doesn't seem to be a reason
to call it again right after.
It also appears that second uart_write_wakeup() might potentially
cause unwanted write wakeup when transmitting an x_char. See commit 5e42e9a30cda ("serial: imx: Fix x_char handling and tx flow control")
where this problem was fixed in a very similarly structured i.MX UART
driver.
It appears that lpuart_rxint, lpuart_txint and lpuart32_rxint were
modelled after identical function found in UART driver for
i.MX. However, while said functions are used as individual IRQ
handlers in i.MX driver (in case of i.MX1), it is not the case for
LPUART. Given that, there's no need for us to restrict the prototype
of the handler to irqreturn_t foo(int, void *) and we can drop all of
uneened boilerplate code by changing it void foo(struct lpuart_port *).
Stefan Agner [Mon, 29 Jul 2019 19:52:04 +0000 (12:52 -0700)]
tty: serial: fsl_lpuart: flush receive FIFO after overruns
After overruns the FIFO pointers become misaligned. This
typically shows by characters still being stuck in the FIFO
despite the empty flag being asserted. After the first
assertion of the overrun flag the empty flag still seems to
indicate FIFO state correctly and all data can be read.
However, after another overrun assertion the FIFO seems to
be off by one such that the last received character is still
in the FIFO (despite the empty flag being asserted).
Flushing the receive FIFO reinitializes pointers. Hence it
is recommended to flush the FIFO after overruns, see also:
https://community.nxp.com/thread/321175
Hence, on assertion of the overrun flag read the remaining
data from the FIFO and flush buffers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-3-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner [Mon, 29 Jul 2019 19:52:03 +0000 (12:52 -0700)]
tty: serial: fsl_lpuart: fix framing error handling when using DMA
When using DMA framing error get cleared properly. However, due
to the additional read from the data register, an underflow in
the receive FIFO buffer occurs (the FIFO pointer gets out of
sync).
Clear the FIFO in case an underflow has occurred. Also disable the
receiver during this operation and when reading the data register to
minimize potential interference.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-2-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Called in only one place, for RS232, it only obscures things, as it
doesn't go well with 2 similar named functions,
imx_uart_rts_inactive() and imx_uart_rts_active(), that both are
RS485-specific.
serial: imx: set_mctrl(): correctly restore autoRTS state
imx_uart_set_mctrl() happened to set UCR2_CTSC bit whenever TIOCM_RTS
was set, no matter if RTS/CTS handshake is enabled or not. Now fixed by
turning handshake on only when CRTSCTS bit for the port is set.
serial: imx: set_termios(): do not enable autoRTS if RTS is unset
Don't let receiver hardware automatically control RTS output if it
was requested to be inactive.
To ensure this, set_termios() shouldn't set UCR2_CTSC bit if UCR2_CTS
(=TIOCM_RTS) is cleared. Added corresponding check in imx_uart_rts_auto()
to fix this.
8250_lpss: check null return when calling pci_ioremap_bar
pci_ioremap_bar may return null. This is eventually de-referenced at
drivers/dma/dw/core.c:1154 and drivers/dma/dw/core.c:1168. A null check
is needed to prevent null de-reference. I am adding the check and in
case of failure. Thanks to Andy Shevchenko for the hint on the necessity
of pci_iounmap when exiting.
tty: serial: fsl_lpuart: remove the dev.coherent_dma_mask zero setting
By default, .of_dma_configure() init dev.coherent_dma_mask to BIT(32) that
match the eDMA address range. If re-init dev.coherent_dma_mask to zero, then
streaming dma mapping will go swiotlb dma_map, if swiotlb is not initalized
then it causes mapping failed.
Andy Shevchenko [Sun, 21 Jul 2019 15:01:35 +0000 (18:01 +0300)]
serial: 8250_exar: Use struct_size() helper
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array.
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
tty: serial: Remove call to memset after pci_alloc_consistent
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Tony Lindgren [Tue, 23 Jul 2019 11:54:00 +0000 (04:54 -0700)]
serial: 8250_omap: Fix idling for unloaded serdev drivers
For many years omap variants have been setting the runtime PM
autosuspend delay to -1 to prevent unsafe policy with lossy first
character on wake-up. The user must specifically enable the timeout
for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads
into UARTs not idling if no serdev devices are loaded and there is no
sysfs entry to configure the UART in that case. And this means that
my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child
node, and we can simply skip the workround in that case. And the
serdev driver can idle the port during runtime when suitable if an
out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
Linus Torvalds [Sun, 11 Aug 2019 20:15:10 +0000 (13:15 -0700)]
Merge tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax fixes from Dan Williams:
"A filesystem-dax and device-dax fix for v5.3.
The filesystem-dax fix is tagged for stable as the implementation has
been mistakenly throwing away all cow pages on any truncate or hole
punch operation as part of the solution to coordinate device-dma vs
truncate to dax pages.
The device-dax change fixes up a regression this cycle from the
introduction of a common 'internal per-cpu-ref' implementation.
Summary:
- Fix dax_layout_busy_page() to not discard private cow pages of
fs/dax private mappings.
- Update the memremap_pages core to properly cleanup on behalf of
internal reference-count users like device-dax"
* tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm/memremap: Fix reuse of pgmap instances with internal references
dax: dax_layout_busy_page() should not unmap cow pages
Linus Torvalds [Sat, 10 Aug 2019 23:31:47 +0000 (16:31 -0700)]
Merge tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"A few minor RISC-V updates for v5.3-rc4:
- Remove __udivdi3() from the 32-bit Linux port, converting the only
upstream user to use do_div(), per Linux policy
- Convert the RISC-V standard clocksource away from per-cpu data
structures, since only one is used by Linux, even on a multi-CPU
system
- A set of DT binding updates that remove an obsolete text binding in
favor of a YAML binding, fix a bogus compatible string in the
schema (thus fixing a "make dtbs_check" warning), and clarifies the
future values expected in one of the RISC-V CPU properties"
* tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
dt-bindings: riscv: fix the schema compatible string for the HiFive Unleashed board
dt-bindings: riscv: remove obsolete cpus.txt
RISC-V: Remove udivdi3
riscv: delay: use do_div() instead of __udivdi3()
dt-bindings: Update the riscv,isa string description
RISC-V: Remove per cpu clocksource
Linus Torvalds [Sat, 10 Aug 2019 23:24:03 +0000 (16:24 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A few fixes for x86:
- Don't reset the carefully adjusted build flags for the purgatory
and remove the unwanted flags instead. The 'reset all' approach led
to build fails under certain circumstances.
- Unbreak CLANG build of the purgatory by avoiding the builtin
memcpy/memset implementations.
- Address missing prototype warnings by including the proper header
- Fix yet more fall-through issues"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/lib/cpu: Address missing prototypes warning
x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS
x86/purgatory: Do not use __builtin_memcpy and __builtin_memset
x86: mtrr: cyrix: Mark expected switch fall-through
x86/ptrace: Mark expected switch fall-through
Linus Torvalds [Sat, 10 Aug 2019 23:19:02 +0000 (16:19 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Thomas Gleixner:
"Perf tooling fixes all over the place:
- Fix the selection of the main thread COMM in db-export
- Fix the disassemmbly display for BPF in annotate
- Fix cpumap mask setup in perf ftrace when only one CPU is present
- Add the missing 'cpu_clk_unhalted.core' event
- Fix CPU 0 bindings in NUMA benchmarks
- Fix the module size calculations for s390
- Handle the gap between kernel end and module start on s390
correctly
- Build and typo fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf pmu-events: Fix missing "cpu_clk_unhalted.core" event
perf annotate: Fix s390 gap between kernel end and module start
perf record: Fix module size on s390
perf tools: Fix include paths in ui directory
perf tools: Fix a typo in a variable name in the Documentation Makefile
perf cpumap: Fix writing to illegal memory in handling cpumap mask
perf ftrace: Fix failure to set cpumask when only one cpu is present
perf db-export: Fix thread__exec_comm()
perf annotate: Fix printing of unaugmented disassembled instructions from BPF
perf bench numa: Fix cpu0 binding
Linus Torvalds [Sat, 10 Aug 2019 22:48:02 +0000 (15:48 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Three fixlets for the scheduler:
- Avoid double bandwidth accounting in the push & pull code
- Use a sane FIFO priority for the Pressure Stall Information (PSI)
thread.
- Avoid permission checks when setting the scheduler params for the
PSI thread"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/psi: Do not require setsched permission from the trigger creator
sched/psi: Reduce psimon FIFO priority
sched/deadline: Fix double accounting of rq/running bw in push & pull
Linus Torvalds [Sat, 10 Aug 2019 22:46:25 +0000 (15:46 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A small fix for the affinity spreading code.
It failed to handle situations where a single vector was requested
either due to only one CPU being available or vector exhaustion
causing only a single interrupt to be granted.
The fix is to simply remove the requirement in the affinity spreading
code for more than one interrupt being available"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Create affinity mask for single vector
Joe Perches [Mon, 5 Aug 2019 22:11:15 +0000 (15:11 -0700)]
Makefile: Convert -Wimplicit-fallthrough=3 to just -Wimplicit-fallthrough for clang
A compilation -Wimplicit-fallthrough warning was enabled by commit a035d552a93b ("Makefile: Globally enable fall-through warning")
Even though clang 10.0.0 does not currently support this warning without
a patch, clang currently does not support a value for this option.
Link: https://bugs.llvm.org/show_bug.cgi?id=39382
The gcc default for this warning is 3 so removing the =3 has no effect
for gcc and enables the warning for patched versions of clang.
Also remove the =3 from an existing use in a parisc Makefile:
arch/parisc/math-emu/Makefile
Signed-off-by: Joe Perches <joe@perches.com> Reviewed-and-tested-by: Nathan Chancellor <natechancellor@gmail.com> Cc: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 10 Aug 2019 19:24:20 +0000 (12:24 -0700)]
Merge tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes Greg KH:
"Here are some small char/misc driver fixes for 5.3-rc4.
Two of these are for the habanalabs driver for issues found when
running on a big-endian system (are they still alive?) The others are
tiny fixes reported by people, and a MAINTAINERS update about the
location of the fpga development tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: Fix DEBUG_LOCKS_WARN_ON for uninitialized attribute
MAINTAINERS: Move linux-fpga tree to new location
nvmem: Use the same permissions for eeprom as for nvmem
habanalabs: fix host memory polling in BE architecture
habanalabs: fix F/W download in BE architecture
Linus Torvalds [Sat, 10 Aug 2019 19:20:02 +0000 (12:20 -0700)]
Merge tag 'driver-core-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small fixes for some driver core issues that have been
reported. There is also a kernfs "fix" here, which was then reverted
because it was found to cause problems in linux-next.
The driver core fixes both resolve reported issues, one with gpioint
stuff that showed up in 5.3-rc1, and the other finally (and hopefully)
resolves a very long standing race when removing glue directories.
It's nice to get that issue finally resolved and the developers
involved should be applauded for the persistence it took to get this
patch finally accepted.
All of these have been in linux-next for a while with no reported
issues. Well, the one reported issue, hence the revert :)"
* tag 'driver-core-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "kernfs: fix memleak in kernel_ops_readdir()"
kernfs: fix memleak in kernel_ops_readdir()
driver core: Fix use-after-free and double free on glue directory
driver core: platform: return -ENXIO for missing GpioInt
Linus Torvalds [Sat, 10 Aug 2019 19:17:12 +0000 (12:17 -0700)]
Merge tag 'tty-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fix from Greg KH:
"Here is a single tty kgdb fix for 5.3-rc4.
It fixes an annoying log message that has caused kdb to become
useless. It's another fallout from commit ddde3c18b700 ("vt: More
locking checks") which tries to enforce locking checks more strictly
in the tty layer, unfortunatly when kdb is stopped, there's no need
for locks :)
This patch has been linux-next for a while with no reported issues"
* tag 'tty-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
kgdboc: disable the console lock when in kgdb
Linus Torvalds [Sat, 10 Aug 2019 18:59:57 +0000 (11:59 -0700)]
Merge tag 'usb-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.3-rc4.
The "biggest" one here is moving code from one file to another in
order to fix a long-standing race condition with the creation of sysfs
files for USB devices. Turns out that there are now userspace tools
out there that are hitting this long-known bug, so it's time to fix
them. Thankfully the tool-maker in this case fixed the issue :)
The other patches in here are all fixes for reported issues. Now that
syzbot knows how to fuzz USB drivers better, and is starting to now
fuzz the userspace facing side of them at the same time, there will be
more and more small fixes like these coming, which is a good thing.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: setup authorized_default attributes using usb_bus_notify
usb: iowarrior: fix deadlock on disconnect
Revert "USB: rio500: simplify locking"
usb: usbfs: fix double-free of usb memory upon submiturb error
usb: yurex: Fix use-after-free in yurex_delete
usb: typec: tcpm: Ignore unsupported/unknown alternate mode requests
xhci: Fix NULL pointer dereference at endpoint zero reset.
usb: host: xhci-rcar: Fix timeout in xhci_suspend()
usb: typec: ucsi: ccg: Fix uninitilized symbol error
usb: typec: tcpm: remove tcpm dir if no children
usb: typec: tcpm: free log buf memory when remove debug file
usb: typec: tcpm: Add NULL check before dereferencing config
Linus Torvalds [Sat, 10 Aug 2019 17:21:25 +0000 (10:21 -0700)]
Merge tag 'pinctrl-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Delay acquisition of regmaps in the Aspeed G5 driver.
- Make a symbol static to reduce compiler noise.
* tag 'pinctrl-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed: Make aspeed_pinmux_ips static
pinctrl: aspeed-g5: Delay acquisition of regmaps
Linus Torvalds [Sat, 10 Aug 2019 17:17:19 +0000 (10:17 -0700)]
Merge tag 'powerpc-5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Just one fix, a revert of a commit that was meant to be a minor
improvement to some inline asm, but ended up having no real benefit
with GCC and broke booting 32-bit machines when using Clang.
Thanks to: Arnd Bergmann, Christophe Leroy, Nathan Chancellor, Nick
Desaulniers, Segher Boessenkool"
* tag 'powerpc-5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc: slightly improve cache helpers"
Linus Torvalds [Sat, 10 Aug 2019 17:10:33 +0000 (10:10 -0700)]
Merge tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fall-through fixes from Gustavo A. R. Silva:
"Mark more switch cases where we are expecting to fall through, fixing
fall-through warnings in arm, sparc64, mips, i386 and s390"
* tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
ARM: ep93xx: Mark expected switch fall-through
scsi: fas216: Mark expected switch fall-throughs
pcmcia: db1xxx_ss: Mark expected switch fall-throughs
video: fbdev: omapfb_main: Mark expected switch fall-throughs
watchdog: riowd: Mark expected switch fall-through
s390/net: Mark expected switch fall-throughs
crypto: ux500/crypt: Mark expected switch fall-throughs
watchdog: wdt977: Mark expected switch fall-through
watchdog: scx200_wdt: Mark expected switch fall-through
watchdog: Mark expected switch fall-throughs
ARM: signal: Mark expected switch fall-through
mfd: omap-usb-host: Mark expected switch fall-throughs
mfd: db8500-prcmu: Mark expected switch fall-throughs
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: alignment: Mark expected switch fall-throughs
ARM: tegra: Mark expected switch fall-through
ARM/hw_breakpoint: Mark expected switch fall-throughs
Linus Torvalds [Sat, 10 Aug 2019 03:31:04 +0000 (20:31 -0700)]
Merge tag 'kbuild-fixes-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- revive single target %.ko
- do not create built-in.a where it is unneeded
- do not create modules.order where it is unneeded
- show a warning if subdir-y/m is used to visit a module Makefile
* tag 'kbuild-fixes-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: show hint if subdir-y/m is used to visit module Makefile
kbuild: generate modules.order only in directories visited by obj-y/m
kbuild: fix false-positive need-builtin calculation
kbuild: revive single target %.ko
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: arm-ep93xx_defconfig arm):
arch/arm/mach-ep93xx/crunch.c: In function 'crunch_do':
arch/arm/mach-ep93xx/crunch.c:46:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
memset(crunch_state, 0, sizeof(*crunch_state));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-ep93xx/crunch.c:53:2: note: here
case THREAD_NOTIFY_EXIT:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>