powerpc/tau: Synchronize function prototypes and body
Some function prototypes and body for Thermal Assist Units were not in
sync. Update the function definition to match the existing function
declaration found in `setup-common.c`, changing an `int` return type to a
`u32` return type. Move the prototypes to a header file. Fix the following
warnings, treated as error with W=1:
arch/powerpc/kernel/tau_6xx.c:257:5: error: no previous prototype for ‘cpu_temp_both’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:262:5: error: no previous prototype for ‘cpu_temp’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:267:5: error: no previous prototype for ‘tau_interrupts’ [-Werror=missing-prototypes]
The function prototypes were declared within a `#ifdef CONFIG_PPC_LITE5200`
block which would prevent them from being visible when compiling
`mpc52xx_pm.c`. Move the prototypes outside of the `#ifdef` block to fix
the following warnings treated as errors with W=1:
arch/powerpc/platforms/52xx/mpc52xx_pm.c:58:5: error: no previous prototype for ‘mpc52xx_pm_prepare’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:113:5: error: no previous prototype for ‘mpc52xx_pm_enter’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:181:6: error: no previous prototype for ‘mpc52xx_pm_finish’ [-Werror=missing-prototypes]
powerpc/powermac: Move pmac_pfunc_base_install prototype to header file
The pmac_pfunc_base_install prototype was declared in powermac/smp.c since
function was used there, move it to pmac_pfunc.h header to be visible in
pfunc_base.c. Fix a warning treated as error with W=1:
arch/powerpc/platforms/powermac/pfunc_base.c:330:12: error: no previous prototype for ‘pmac_pfunc_base_install’ [-Werror=missing-prototypes]
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/pci.c:34:5: error: no previous prototype for ‘gg2_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:61:5: error: no previous prototype for ‘gg2_write_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:97:5: error: no previous prototype for ‘rtas_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:112:5: error: no previous prototype for ‘rtas_write_config’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/chrp/setup: Remove idu_size variable and make some functions static
Remove variable declaration idu_size and associated code since not used.
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/setup.c:97:6: error: no previous prototype for ‘chrp_show_cpuinfo’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:302:13: error: no previous prototype for ‘chrp_setup_arch’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:385:16: error: variable ‘idu_size’ set but not used [-Werror=unused-but-set-variable]
arch/powerpc/platforms/chrp/setup.c:526:13: error: no previous prototype for ‘chrp_init_IRQ’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:559:1: error: no previous prototype for ‘chrp_init2’ [-Werror=missing-prototypes]
powerpc/mm/radix: Use do/while(0) trick for single statement block
In commit 7a22d6321c3d ("powerpc/mm/radix: Update command line parsing for
disable_radix") an `if` statement was added for a possible empty body
(prom_debug).
Fix the following warning, treated as error with W=1:
arch/powerpc/kernel/prom_init.c:656:46: error: suggest braces around empty body in an ‘if’ statement [-Werror=empty-body]
Suggested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/sparse: Fix plain integer as NULL pointer warning
Trivial fix to remove the following sparse warnings:
arch/powerpc/kernel/module_32.c:112:74: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/module_32.c:117:74: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1155:28: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1230:20: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1385:36: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1752:23: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2084:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2110:32: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2167:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2183:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:277:20: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:155:67: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:247:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:249:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:252:37: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:127:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:148:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:44:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:57:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:87:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:160:31: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:167:22: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:274:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:285:31: warning: Using plain integer as NULL pointer
arch/powerpc/include/asm/hugetlb.h:204:16: warning: Using plain integer as NULL pointer
arch/powerpc/mm/ppc_mmu_32.c:170:21: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:1227:23: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:65:24: warning: Using plain integer as NULL pointer
Also use `--fix` command line option from `script/checkpatch --strict` to
remove the following:
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#72: FILE: arch/powerpc/kernel/btext.c:160:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "!vbase"
#80: FILE: arch/powerpc/kernel/btext.c:167:
+ if (vbase == NULL)
CHECK: Comparison to NULL could be written "!base"
#89: FILE: arch/powerpc/kernel/btext.c:274:
+ if (base == NULL)
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#98: FILE: arch/powerpc/kernel/btext.c:285:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "strstr"
#117: FILE: arch/powerpc/kernel/module_32.c:117:
+ if (strstr(secstrings + sechdrs[i].sh_name, ".debug") != NULL)
CHECK: Comparison to NULL could be written "!Hash"
#130: FILE: arch/powerpc/mm/ppc_mmu_32.c:170:
+ if (Hash == NULL)
CHECK: Comparison to NULL could be written "Hash"
#143: FILE: arch/powerpc/mm/tlb_hash32.c:44:
+ if (Hash != NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#152: FILE: arch/powerpc/mm/tlb_hash32.c:57:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#161: FILE: arch/powerpc/mm/tlb_hash32.c:87:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#170: FILE: arch/powerpc/mm/tlb_hash32.c:127:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#179: FILE: arch/powerpc/mm/tlb_hash32.c:148:
+ if (Hash == NULL) {
ERROR: space required after that ';' (ctx:VxV)
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "node"
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "!region"
#201: FILE: arch/powerpc/platforms/powermac/pci.c:1227:
+ if (region == NULL)
CHECK: Comparison to NULL could be written "of_get_property"
#214: FILE: arch/powerpc/platforms/powermac/setup.c:155:
+ if (of_get_property(np, "cache-unified", NULL) != NULL && dc) {
CHECK: Comparison to NULL could be written "!np"
#223: FILE: arch/powerpc/platforms/powermac/setup.c:247:
+ if (np == NULL)
CHECK: Comparison to NULL could be written "np"
#226: FILE: arch/powerpc/platforms/powermac/setup.c:249:
+ if (np != NULL) {
CHECK: Comparison to NULL could be written "l2cr"
#230: FILE: arch/powerpc/platforms/powermac/setup.c:252:
+ if (l2cr != NULL) {
CHECK: Comparison to NULL could be written "via"
#243: FILE: drivers/macintosh/via-pmu.c:277:
+ if (via != NULL)
CHECK: Comparison to NULL could be written "current_req"
#252: FILE: drivers/macintosh/via-pmu.c:1155:
+ if (current_req != NULL) {
CHECK: Comparison to NULL could be written "!req"
#261: FILE: drivers/macintosh/via-pmu.c:1230:
+ if (req == NULL || pmu_state != idle
CHECK: Comparison to NULL could be written "!req"
#270: FILE: drivers/macintosh/via-pmu.c:1385:
+ if (req == NULL) {
CHECK: Comparison to NULL could be written "!pp"
#288: FILE: drivers/macintosh/via-pmu.c:2084:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#297: FILE: drivers/macintosh/via-pmu.c:2110:
+ if (count < 1 || pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#306: FILE: drivers/macintosh/via-pmu.c:2167:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "pp"
#315: FILE: drivers/macintosh/via-pmu.c:2183:
+ if (pp != NULL) {
powerpc/altivec: Add missing prototypes for altivec
Some functions prototypes were missing for the non-altivec code. Add the
missing prototypes in a new header file, fix warnings treated as errors
with W=1:
arch/powerpc/lib/xor_vmx_glue.c:18:6: error: no previous prototype for ‘xor_altivec_2’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:29:6: error: no previous prototype for ‘xor_altivec_3’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:40:6: error: no previous prototype for ‘xor_altivec_4’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:52:6: error: no previous prototype for ‘xor_altivec_5’ [-Werror=missing-prototypes]
The prototypes were already present in <asm/xor.h> but this header file is
meant to be included after <include/linux/raid/xor.h>. Trying to re-use
<asm/xor.h> directly would lead to warnings such as:
arch/powerpc/include/asm/xor.h:39:15: error: variable ‘xor_block_altivec’ has initializer but incomplete type
Trying to re-use <asm/xor.h> after <include/linux/raid/xor.h> in
xor_vmx_glue.c would in turn trigger the following warnings:
include/asm-generic/xor.h:688:34: error: ‘xor_block_32regs’ defined but not used [-Werror=unused-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 21 May 2018 11:28:34 +0000 (21:28 +1000)]
powerpc/xmon: Realign paca dump fields
We've added some fields with longer names since we originally wrote
this, so the fields are no longer lined up. Adjust the widths to make
it all look nice again, eg:
powerpc/xmon: Add __printf annotation to xmon_printf()
This allows the compiler to verify the format strings vs the types of
the arguments.
Update the other prototype declarations in asm/xmon.h.
Silence warnings (triggered at W=1) by adding relevant __printf
attribute. Move #define at bottom of the file to prevent conflict with
gcc attribute.
Solves the original warning:
arch/powerpc/xmon/nonstdio.c:178:2: error: function might be
possible candidate for ‘gnu_printf’ format attribute
In turn this uncovered many formatting errors in xmon.c, all fixed in
this patch.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Always use px not p, fixup the 44x specific code, tweak change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 21 May 2018 11:06:19 +0000 (21:06 +1000)]
powerpc/xmon: Specify the full format in DUMP() macro
In dump_one_paca() the DUMP macro unconditionally prepends '#' to the
printf format specifier. In most cases we're using either 'x' or 'lx'
etc. and that is OK. But for 'p' and other formats using '#' is
actually undefined, and once we enable printf() checking for
xmon_printf() we will get warnings from the compiler.
So just have each usage specify the full format, that way we can omit
'#' when it's inappropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Mathieu Malaterre <malat@debian.org>
Michal Suchanek [Wed, 23 May 2018 18:00:54 +0000 (20:00 +0200)]
powerpc/xmon: Also setup debugger hooks when single-stepping
When single-stepping kernel code from xmon without a debug hook
enabled the kernel crashes. This can happen when kernel starts with
xmon on crash disabled but xmon is entered using sysrq.
Call force_enable_xmon when single-stepping in xmon to install the
xmon debug hooks.
Fixes: e1368d0c9edb ("powerpc/xmon: Setup debugger hooks when first break-point is set") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Tue, 22 May 2018 06:14:27 +0000 (16:14 +1000)]
selftests/powerpc: Add ptrace hw breakpoint test
This test the ptrace hw breakpoints via PTRACE_SET_DEBUGREG and
PPC_PTRACE_SETHWDEBUG. This test was use to find the bugs fixed by
these recent commits:
4f7c06e26e powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG cd6ef7eebf powerpc/ptrace: Fix enforcement of DAWR constraints
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Add SPDX tag, clang format it] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 23 May 2018 08:53:22 +0000 (10:53 +0200)]
powerpc/mm: Only read faulting instruction when necessary in do_page_fault()
Commit a7a9dcd882a67 ("powerpc: Avoid taking a data miss on every
userspace instruction miss") has shown that limiting the read of
faulting instruction to likely cases improves performance.
This patch goes further into this direction by limiting the read
of the faulting instruction to the only cases where it is likely
needed.
On an MPC885, with the same benchmark app as in the commit referred
above, we see a reduction of about 3900 dTLB misses (approx 3%):
Before the patch:
Performance counter stats for './fault 500' (10 runs):
The proper work of the huge stack expansion was tested with the
following app:
int main(int argc, char **argv)
{
char buf[1024 * 1025];
sprintf(buf, "Hello world !\n");
printf(buf);
exit(0);
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add include of pagemap.h to fix build errors] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hwmon: (ibmpowernv): Add support to read 64 bit sensors
The firmware has supported for reading sensor values of size u32.
This patch adds support to use newer firmware functions which allows
to read the sensors of size u64.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 17 May 2018 05:37:15 +0000 (15:37 +1000)]
powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG
In commit e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 17 May 2018 05:37:14 +0000 (15:37 +1000)]
powerpc/ptrace: Fix enforcement of DAWR constraints
Back when we first introduced the DAWR, in commit 4ae7ebe9522a
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add byte-swapping versions of __raw_writeq() and __raw_rm_writeq().
This allows us to avoid sparse warnings caused by passing __be64 to
__raw_writeq(), which takes unsigned long:
arch/powerpc/platforms/powernv/pci-ioda.c:1981:38:
warning: incorrect type in argument 1 (different base types)
expected unsigned long [unsigned] v
got restricted __be64 [usertype] <noident>
It's also generally preferable to use a byte-swapping accessor rather
than doing it by hand in the code, which is more bug prone.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Anju T Sudhakar [Wed, 16 May 2018 06:35:18 +0000 (12:05 +0530)]
powerpc/perf: Fix memory allocation for core-imc based on num_possible_cpus()
Currently memory is allocated for core-imc based on cpu_present_mask,
which has bit 'cpu' set iff cpu is populated. We use (cpu number / threads
per core) as the array index to access the memory.
Under some circumstances firmware marks a CPU as GUARDed CPU and boot the
system, until cleared of errors, these CPU's are unavailable for all
subsequent boots. GUARDed CPUs are possible but not present from linux
view, so it blows a hole when we assume the max length of our allocation
is driven by our max present cpus, where as one of the cpus might be online
and be beyond the max present cpus, due to the hole.
So (cpu number / threads per core) value bounds the array index and leads
to memory overflow.
Call trace observed during a guard test:
Faulting instruction address: 0xc000000000149f1c
cpu 0x69: Vector: 380 (Data Access Out of Range) at [c000003fea303420]
pc:c000000000149f1c: prefetch_freepointer+0x14/0x30
lr:c00000000014e0f8: __kmalloc+0x1a8/0x1ac
sp:c000003fea3036a0
msr:9000000000009033
dar:c9c54b2c91dbf6b7
current = 0xc000003fea2c0000
paca = 0xc00000000fddd880 softe: 3 irq_happened: 0x01
pid = 1, comm = swapper/104
Linux version 4.16.7-openpower1 (smc@smc-desktop) (gcc version 6.4.0
(Buildroot 2018.02.1-00006-ga8d1126)) #2 SMP Fri May 4 16:44:54 PDT 2018
enter ? for help
call trace:
__kmalloc+0x1a8/0x1ac
(unreliable)
init_imc_pmu+0x7f4/0xbf0
opal_imc_counters_probe+0x3fc/0x43c
platform_drv_probe+0x48/0x80
driver_probe_device+0x22c/0x308
__driver_attach+0xa0/0xd8
bus_for_each_dev+0x88/0xb4
driver_attach+0x2c/0x40
bus_add_driver+0x1e8/0x228
driver_register+0xd0/0x114
__platform_driver_register+0x50/0x64
opal_imc_driver_init+0x24/0x38
do_one_initcall+0x150/0x15c
kernel_init_freeable+0x250/0x254
kernel_init+0x1c/0x150
ret_from_kernel_thread+0x5c/0xc8
Allocating memory for core-imc based on cpu_possible_mask, which has
bit 'cpu' set iff cpu is populatable, will fix this issue.
Finn Thain [Fri, 18 May 2018 01:18:33 +0000 (11:18 +1000)]
powerpc/lib: Fix "integer constant is too large" build failure
My powerpc-linux-gnu-gcc v4.4.5 compiler can't build a 32-bit kernel
any more:
arch/powerpc/lib/sstep.c: In function 'do_popcnt':
arch/powerpc/lib/sstep.c:1068: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1070: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1079: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c: In function 'do_prty':
arch/powerpc/lib/sstep.c:1117: error: integer constant is too large for 'long' type
This file gets compiled with -std=gnu89 which means a constant can be
given the type 'long' even if it won't fit. Fix the errors with a 'ULL'
suffix on the relevant constants.
Nicholas Piggin [Mon, 14 May 2018 15:59:46 +0000 (01:59 +1000)]
powerpc/powernv: Fix opal_event_shutdown() called with interrupts disabled
A kernel crash in process context that calls emergency_restart from
panic will end up calling opal_event_shutdown with interrupts disabled
but not in interrupt. This causes a sleeping function to be called
which gives the following warning with sysrq+c:
Rebooting in 10 seconds..
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
in_atomic(): 0, irqs_disabled(): 1, pid: 7669, name: bash
CPU: 20 PID: 7669 Comm: bash Tainted: G D W 4.17.0-rc5+ #3
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
___might_sleep+0x174/0x1a0
mutex_lock+0x38/0xb0
__free_irq+0x68/0x460
free_irq+0x70/0xc0
opal_event_shutdown+0xb4/0xf0
opal_shutdown+0x24/0xa0
pnv_shutdown+0x28/0x40
machine_shutdown+0x44/0x60
machine_restart+0x28/0x80
emergency_restart+0x30/0x50
panic+0x2a0/0x328
oops_end+0x1ec/0x1f0
bad_page_fault+0xe8/0x154
handle_page_fault+0x34/0x38
--- interrupt: 300 at sysrq_handle_crash+0x44/0x60
LR = __handle_sysrq+0xfc/0x260
flag_spec.62335+0x12b844/0x1e8db4 (unreliable)
__handle_sysrq+0xfc/0x260
write_sysrq_trigger+0xa8/0xb0
proc_reg_write+0xac/0x110
__vfs_write+0x6c/0x240
vfs_write+0xd0/0x240
ksys_write+0x6c/0x110
Fixes: 9f0fd0499d30 ("powerpc/powernv: Add a virtual irqchip for opal events") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/32: Use stmw/lmw for registers save/restore in asm
arch/powerpc/Makefile activates -mmultiple on BE PPC32 configs
in order to use multiple word instructions in functions entry/exit.
The patch does the same for the asm parts, for consistency.
On processors like the 8xx on which insn fetching is pretty slow,
this speeds up registers save/restore.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: PPC32 is BE only, so drop the endian checks] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
That commit was pointless, because csum_add() sums two 32 bits
values, so the sum is 0x1fffffffe at the maximum.
And then when adding upper part (1) and lower part (0xfffffffe),
the result is 0xffffffff which doesn't carry.
Any lower value will not carry either.
And behind the fact that this commit is useless, it also kills the
whole purpose of having an arch specific inline csum_add()
because the resulting code gets even worse than what is obtained
with the generic implementation of csum_add()
powerpc/embedded6xx/hlwd-pic: Prevent interrupts from being handled by Starlet
The interrupt controller inside the Wii's Hollywood chip is connected to
two masters, the "Broadway" PowerPC and the "Starlet" ARM926, each with
their own interrupt status and mask registers.
When booting the Wii with mini[1], interrupts from the SD card
controller (IRQ 7) are handled by the ARM, because mini provides SD
access over IPC. Linux however can't currently use or disable this IPC
service, so both sides try to handle IRQ 7 without coordination.
Let's instead make sure that all interrupts that are unmasked on the PPC
side are masked on the ARM side; this will also make sure that Linux can
properly talk to the SD card controller (and potentially other devices).
If access to a device through IPC is desired in the future, interrupts
from that device should not be handled by Linux directly.
[1]: https://github.com/lewurm/mini
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/embedded6xx/flipper-pic: Don't match all IRQ domains
On the Wii, there is a secondary IRQ controller (hlwd-pic), so
flipper-pic's match operation should not be hardcoded to return 1.
In fact, the default matching logic is sufficient, and we can completely
omit flipper_pic_match.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/book3s64/4k: Switch 4k pagesize config to use pagetable fragment
4K config use one full page at level 4 of the pagetable. Add support for single
fragment allocation in pagetable fragment code and and use that for 4K config.
This makes both 4k and 64k use the same code path. Later we will switch pmd to
use the page table fragment code. This is done only for 64bit platforms which
is using page table fragment support.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/nohash: Remove pte fragment dependency from nohash
Now that we have removed 64K page size support, the RCU page table free can
be much simpler for nohash. Make a copy of the the rcu callback to pgalloc.h
header similar to nohash 32. We could possibly merge 32 and 64 bit there. But
that is for a later patch
We also move the book3s specific handler to pgtable_book3s64.c. This will be
updated in a later patch to handle split pmd ptlock.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/kvm: Switch kvm pmd allocator to custom allocator
In the next set of patches, we will switch pmd allocator to use page fragments
and the locking will be updated to split pmd ptlock. We want to avoid using
fragments for partition-scoped table. Use slab cache similar to level 4 table
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/cell/spufs: Change return type to vm_fault_t
Use new return type vm_fault_t for fault handler. For now, this is
just documenting that the function returns a VM_FAULT value rather
than an errno. Once all instances are converted, vm_fault_t will
become a distinct type. See commit 1c8f422059ae ("mm: change return
type to vm_fault_t").
We are fixing a minor bug, that the error from vm_insert_pfn() was
being ignored and the effect of this is likely to be only felt in OOM
situations.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 12 May 2018 03:35:24 +0000 (13:35 +1000)]
selftests/powerpc: fix exec benchmark
The exec_target binary could segfault calling _exit(2) because r13
is not set up properly (and libc looks at that when performing a
syscall). Call SYS_exit using syscall(2) which doesn't seem to
have this problem.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/ioda: Use ibm, supported-tce-sizes for IOMMU page size mask
At the moment we assume that IODA2 and newer PHBs can always do 4K/64K/16M
IOMMU pages, however this is not the case for POWER9 and now skiboot
advertises the supported sizes via the device so we use that instead
of hard coding the mask.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 10 May 2018 13:09:13 +0000 (23:09 +1000)]
powerpc/powernv: Fix memtrace build when NUMA=n
Currently memtrace doesn't build if NUMA=n:
In function ‘memtrace_alloc_node’:
arch/powerpc/platforms/powernv/memtrace.c:134:6:
error: the address of ‘contig_page_data’ will always evaluate as ‘true’
if (!NODE_DATA(nid) || !node_spanned_pages(nid))
^
This is because for NUMA=n NODE_DATA(nid) points to an always
allocated structure, contig_page_data.
But even in the NUMA=y case memtrace_alloc_node() is only called for
online nodes, and we should always have a NODE_DATA() allocated for an
online node. So remove the (hopefully) overly paranoid check, which
also means we can build when NUMA=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6a6928c3ea1 ("of/fdt: Convert FDT functions to use
libfdt") (Apr 2014), the generic flat device tree code dropped support
for flat device tree's older than version 0x10 (16).
We still have code in our CPU scanning to cope with flat device tree
versions earlier than 2, which can now never trigger, so drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 16 Apr 2018 14:39:05 +0000 (00:39 +1000)]
powerpc/lib: Add alt patching test of branching past the last instruction
Add a test of the relative branch patching logic in the alternate
section feature fixup code. This tests that if we branch past the last
instruction of the alternate section, the branch is not patched.
That's because the assembler will have created a branch that already
points to the first instruction after the patched section, which is
correct and needs no further patching.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 16 Apr 2018 14:39:04 +0000 (00:39 +1000)]
powerpc/lib: Rename ftr_fixup_test7 to ftr_fixup_test_too_big
We want this to remain the last test (because it's disabled by
default), so give it a non-numbered name so we don't have to renumber
it when adding new tests before it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 16 Apr 2018 14:39:03 +0000 (00:39 +1000)]
powerpc/lib: Fix the feature fixup tests to actually work
The code patching code has always been a bit confused about whether
it's best to use void *, unsigned int *, char *, etc. to point to
instructions. In fact in the feature fixups tests we use both unsigned
int[] and u8[] in different places.
Unfortunately the tests that use unsigned int[] calculate the size of
the code blocks using subtraction of those unsigned int pointers, and
then pass the result to memcmp(). This means we're only comparing 1/4
of the bytes we need to, because we need to multiply by
sizeof(unsigned int) to get the number of *bytes*.
The result is that the tests do all the patching and then only compare
some of the resulting code, so patching bugs that only effect that
last 3/4 of the code could slip through undetected. It turns out that
hasn't been happening, although one test had a bad expected case (see
previous commit).
Fix it for now by multiplying the size by 4 in the affected functions.
Fixes: 362e7701fd18 ("powerpc: Add self-tests of the feature fixup code") Epic-brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 30 Apr 2018 03:27:36 +0000 (13:27 +1000)]
powerpc: Make it clearer that systbl check errors are errors
If the systbl_chk.sh checks fail we print a message, but with no
indication that it's an error. That makes it hard to find in build
logs with eg. grep.
So prefix any output with "Error:".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Al Viro [Wed, 2 May 2018 13:20:50 +0000 (23:20 +1000)]
powerpc/syscalls: kill ppc32_select()
it had always been pointless - compat_sys_select() sign-extends
the first argument just fine on its own.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Use COMPAT_SPU_NEW() to keep systbl_chk.sh happy] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the select system call is wired up with the SYSX_SPU()
macro. The SYSX_SPU() is not handled by systbl_chk.c, which means the
syscall number for select is not checked.
That hides the fact that the syscall number for select is actually
__NR__newselect not __NR_select.
In a following patch we'd like to drop ppc32_select() which means
select will become a regular COMPAT_SYS_SPU() syscall. But
COMPAT_SYS_SPU() can't deal with the fact that the syscall number is
actually __NR__newselect. We also can't just redefine __NR_select
because that's still used for the old select call.
So add a new COMPAT_NEW_SPU() that does the same thing as
COMPAT_SYS_SPU() except it encodes that we're using the new number.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Al Viro [Wed, 2 May 2018 13:20:47 +0000 (23:20 +1000)]
powerpc/syscalls: signal_{32, 64} - switch to SYSCALL_DEFINE
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Fix sys_debug_setcontext() prototype to return long] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Torsten Duwe [Fri, 4 May 2018 12:38:34 +0000 (14:38 +0200)]
powerpc/livepatch: Implement reliable stack tracing for the consistency model
The "Power Architecture 64-Bit ELF V2 ABI" says in section 2.3.2.3:
[...] There are several rules that must be adhered to in order to ensure
reliable and consistent call chain backtracing:
* Before a function calls any other function, it shall establish its
own stack frame, whose size shall be a multiple of 16 bytes.
– In instances where a function’s prologue creates a stack frame, the
back-chain word of the stack frame shall be updated atomically with
the value of the stack pointer (r1) when a back chain is implemented.
(This must be supported as default by all ELF V2 ABI-compliant
environments.)
[...]
– The function shall save the link register that contains its return
address in the LR save doubleword of its caller’s stack frame before
calling another function.
To me this sounds like the equivalent of HAVE_RELIABLE_STACKTRACE.
This patch may be unneccessarily limited to ppc64le, but OTOH the only
user of this flag so far is livepatching, which is only implemented on
PPCs with 64-LE, a.k.a. ELF ABI v2.
Feel free to add other ppc variants, but so far only ppc64le got tested.
This change also implements save_stack_trace_tsk_reliable() for ppc64le
that checks for the above conditions, where possible.
Nicholas Piggin [Sat, 5 May 2018 07:26:00 +0000 (17:26 +1000)]
powerpc/watchdog: provide more data in watchdog messages
Provide timebase and timebase of last heartbeat in watchdog lockup
messages. Also provide a stack trace of when a CPU becomes un-stuck,
which can be useful -- it could be where irqs are re-enabled, so it
may be the end of the critical section which is responsible for the
latency which is useful information.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 5 May 2018 07:25:59 +0000 (17:25 +1000)]
powerpc/watchdog: don't update the watchdog timestamp if a lockup is detected
The watchdog heartbeat timestamp is updated when the local heartbeat
timer fires (or touch_nmi_watchdog() is called).
This is an interesting data point, so don't overwrite it when the
soft-NMI interrupt detects a hard lockup. That code came from a pre-
merge version to prevent hard lockup messages flood, but that's taken
care of with the stuck CPU logic now, so there is no reason to
update the heartbeat timestamp here.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/xive: prepare all hcalls to support long busy delays
This is not the case for the moment, but future releases of pHyp might
need to introduce some synchronisation routines under the hood which
would make the XIVE hcalls longer to complete.
As this was done for H_INT_RESET, let's wrap the other hcalls in a
loop catching the H_LONG_BUSY_* codes.
Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/xive: fix hcall H_INT_RESET to support long busy delays
The hcall H_INT_RESET can take some time to complete and in such cases
it returns H_LONG_BUSY_* codes requiring the machine to sleep for a
while before retrying.
Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/64/kexec: fix race in kexec when XIVE is shutdown
The kexec_state KEXEC_STATE_IRQS_OFF barrier is reached by all
secondary CPUs before the kexec_cpu_down() operation is called on
secondaries. This can raise conflicts and provoque errors in the XIVE
hcalls when XIVE is shutdown with H_INT_RESET on the primary CPU.
To synchronize the kexec_cpu_down() operations and make sure the
secondaries have completed their task before the primary starts doing
the same, let's move the primary kexec_cpu_down() after the
KEXEC_STATE_REAL_MODE barrier.
This change of the ending sequence of kexec is mostly useful on the
pseries platform but it impacts also the powernv, ps3 and 85xx
platforms. powernv can be easily tested and fixed but some caution is
required for the other two.
Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Mon, 30 Apr 2018 10:31:50 +0000 (20:31 +1000)]
powerpc/config: powernv_defconfig updates
For consideration:
* Add NVDIMM support - Enables greater testing, mambo device.
* Add IPv6 support built in + additional modules - Because it's 2018 maan.
* Add DEFERRED_STRUCT_PAGE_INIT - Let's see what breaks.
* Add PPC_MEMTRACE - Small powernv debugfs driver for getting hardware traces.
* Add MEMORY_FAILURE - Machine check exceptions can now drive memory failure.
* Turn on FANOTIFY - This is the current filesystem notification feature.
* Turn on SCOM_DEBUGFS - Handy for hardware/firmware debugging, security risk?
* Turn on async SCSI scanning - Let's see what breaks.
* Add MLX5 driver as a module - Popular demand.
* Add CRYPTO_CRCT10DIF_VPMSUM - POWER8 T10DIF acceleration.
* Make a bunch of USB hid drivers modules.
* Make SCSI SG, SR, and FC modules - FC is huge.
* Make video drivers except AST GPU modules - Also huge.
* Make PCI serial driver a module - Uncommon.
* Make more things modules, NFS FS, RAM disk, netconsole, MS-DOS fs.
* Get rid of /dev/port - Not used.
* Remove PPS and PTP subsystms - Unusual.
* Remove legacy BSD ttys - Long dead.
* Remove IDE - Deprecated and replaced with ATA.
* Remove WIRELESS - Until we get POWER9 laptops.
* Remove RAW - Long deprecated in favour of direct IO.
* Remove floppy, parport, and PS2 input devices - not supported.
* Remove virtio drivers, ballooning - We're host only.
* Remove PPP - Sorry Paulus.
The B43 driver only needs CONFIG_SSB to support the WLAN card found in
the Wii. Configure it accordingly, and disable BCMA bus support to save
a bit of space.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc: wii_defconfig: Disable Ethernet driver support code
The Wii doesn't have built-in Ethernet and USB Ethernet adapters are in
a different menu. Disable CONFIG_ETHERNET to save some space in support
code for Ethernet drivers.
Note that this patch doesn't disable any Ethernet drivers, because they
are not enabled by default.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Which can be more easily compared to H_NOT_FOUND in hvcall.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Balbir Singh [Tue, 1 May 2018 02:57:25 +0000 (12:57 +1000)]
Revert "powerpc/powernv: Increase memory block size to 1GB on radix"
This commit was a stop-gap to prevent crashes on hotunplug, caused by
the mismatch between the 1G mappings used for the linear mapping and the
memory block size. Those issues are now resolved because we split the
linear mapping at hotunplug time if necessary, as implemented in commit 4dd5f8a99e79 ("powerpc/mm/radix: Split linear mapping on hot-unplug").
Signed-off-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Tested-by: Rashmica Gupta <rashmica.g@gmail.com> Tested-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/fadump: Unregister fadump on kexec down path.
Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.
Fixes: b500afff11f6 ("fadump: Invalidate registration and release reserved memory for general use.") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hari Bathini [Tue, 10 Apr 2018 13:41:31 +0000 (19:11 +0530)]
powerpc/fadump: Do not use hugepages when fadump is active
FADump capture kernel boots in restricted memory environment preserving
the context of previous kernel to save vmcore. Supporting hugepages in
such environment makes things unnecessarily complicated, as hugepages
need memory set aside for them. This means most of the capture kernel's
memory is used in supporting hugepages. In most cases, this results in
out-of-memory issues while booting FADump capture kernel. But hugepages
are not of much use in capture kernel whose only job is to save vmcore.
So, disabling hugepages support, when fadump is active, is a reliable
solution for the out of memory issues. Introducing a flag variable to
disable HugeTLB support when fadump is active.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/fadump: exclude memory holes while reserving memory in second kernel
The second kernel, during early boot after the crash, reserves rest of
the memory above boot memory size to make sure it does not touch any of the
dump memory area. It uses memblock_reserve() that reserves the specified
memory region irrespective of memory holes present within that region.
There are chances where previous kernel would have hot removed some of
its memory leaving memory holes behind. In such cases fadump kernel reports
incorrect number of reserved pages through arch_reserved_kernel_pages()
hook causing kernel to hang or panic.
Fix this by excluding memory holes while reserving rest of the memory
above boot memory size during second kernel boot after crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
tracing: Remove PPC32 wart from config TRACING_SUPPORT
config TRACING_SUPPORT has an exception for PPC32, because PPC32
didn't have irqflags tracing support.
But that hasn't been true since commit 5d38902c4838 ("powerpc: Add
irqtrace support for 32-bit powerpc") (Jun 2009).
So remove the exception for PPC32 and the comment.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Gortmaker [Mon, 11 Dec 2017 03:29:13 +0000 (22:29 -0500)]
powerpc: remove retired sbc834x support
I no longer have a functional version of this board for even the most
basic sanity boot testing, and they have not been available for purchase
for quite some years now.
There is no point in adding a burden to testing coverage that does
walk all the possible defconfigs, so with all the above in mind, it
makes sense to remove it. Of course it will remain in the git history
for anyone who happens to stumble on one and wants to tinker with it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Tue, 27 Mar 2018 04:29:06 +0000 (15:29 +1100)]
powerpc: Only support DYNAMIC_FTRACE not static
We've had dynamic ftrace support for over 9 years since Steve first
wrote it, all the distros use dynamic, and static is basically
untested these days, so drop support for static ftrace.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc64/ftrace: Implement support for ftrace_regs_caller()
With -mprofile-kernel, we always save the full register state in
ftrace_caller(). While this works, this is inefficient if we're not
interested in the register state, such as when we're using the function
tracer.
Rename the existing ftrace_caller() as ftrace_regs_caller() and provide
a simpler implementation for ftrace_caller() that is used when registers
are not required to be saved.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc64/ftrace: Use the generic version of ftrace_replace_code()
Our implementation matches that of the generic version, which also
handles FTRACE_UPDATE_MODIFY_CALL. So, remove our implementation in
favor of the generic version.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc64/module: Tighten detection of mcount call sites with -mprofile-kernel
For R_PPC64_REL24 relocations, we suppress emitting instructions for TOC
load/restore in the relocation stub if the relocation is for _mcount()
call when using -mprofile-kernel ABI.
To detect this, we check if the preceding instructions are per the
standard set of instructions emitted by gcc: either the two instruction
sequence of 'mflr r0; std r0,16(r1)', or the more optimized variant of a
single 'mflr r0'. This is not sufficient since nothing prevents users
from hand coding sequences involving a 'mflr r0' followed by a 'bl'.
For removing the toc save instruction from the stub, we additionally
check if the symbol is "_mcount". Add the same check here as well.
Also rename is_early_mcount_callsite() to is_mprofile_mcount_callsite()
since that is what is being checked. The use of "early" is misleading
since there is nothing involving this function that qualifies as early.
Fixes: 153086644fd1f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
projects / linux.git / log