Wei Yongjun [Tue, 7 Feb 2017 14:52:58 +0000 (14:52 +0000)]
scsi: qedi: Fix possible memory leak in qedi_iscsi_update_conn()
'conn_info' is malloced in qedi_iscsi_update_conn() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Change testbus default config, dump additional testbus registers along
with other debug vendor specific registers. These additional info are
useful in debugging link related failures.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: ufs: kick start clock scaling only after device detection
UFS clock scaling might start kicking in even before the device
is running at the fastest interface speed which is undesirable.
This change moves the clock scaling kick start only after the
device is detected and running at the fastest interface speed.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: ufs: don't suspend clock scaling during clock gating
Currently we are suspending clock scaling during clock gating which doesn't
allow us to have clock gating timeout lower than clock scaling polling
window. If clock gating timeout is smaller than the clock scaling polling
window then we will mostly suspend the clock scaling before clock scaling
polling window expires and we might get stuck in same state (scaled down
or scaled up) for quite a long time. And for this reason, we have clock
gating timeout (150ms) greater than clock scaling polling window (100ms).
We would like to have aggressive clock gating timeout even lower than the
clock scaling polling window hence this change is decoupling the clock
scaling suspend/resume from clock gate/ungate. We will not suspend the
clock scaling as part of clock gating instead clock scaling context will
schedule scaling suspend work if there are no more pending transfer
requests.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilad Broner [Sat, 4 Feb 2017 00:57:28 +0000 (16:57 -0800)]
scsi: ufs: add host state prints in failure cases
Whenever some UFS failure occurs the driver prints the UFS
registers in order to help with analysis of the failure.
However this may not be sufficient in some cases, so having
the host controller state as it is represented and managed in
the driver will contribute to analysis efforts.
Added prints of various fields in the hba struct which may be
of interest.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS driver's load based clock scaling feature scales down the ufs related
clocks in order to allow low power modes of chipsets. UniPro 1.6 supports
maximum gear up to HS-G3 (High Speed Gear3) and some of the chipsets
low power modes may not be allowed in HS-G3 hence this change adds support
to scale gear between HS-G3 and HS-G1 based on same existing load based
clock scaling logic.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilad Broner [Sat, 4 Feb 2017 00:56:50 +0000 (16:56 -0800)]
scsi: ufs: reduce printout for aborted requests
Details printed for each request that is aborted can overload the
target as there can be several requests that are aborted at once.
This change will print full request details only for the first
aborted request since the last link reset, and minimal details
for other subsequent requests.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilad Broner [Sat, 4 Feb 2017 00:56:40 +0000 (16:56 -0800)]
scsi: ufs: skip request abort task when previous aborts failed
On certain error conditions request abort task itself might fail
when aborting a request. In such case, subsequent request aborts
should skip issuing the abort task as it is expected to fail as well,
and device reset handler will be called next.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Tue, 7 Feb 2017 12:59:30 +0000 (13:59 +0100)]
scsi: aacraid: avoid open-coded upper_32_bits
Shifting a dma_addr_t right by 32 bits causes a compile-time warning
when that type is only 32 bit wide:
drivers/scsi/aacraid/src.c: In function 'aac_src_start_adapter':
drivers/scsi/aacraid/src.c:414:29: error: right shift count >= width of type [-Werror=shift-count-overflow]
This changes the driver to use the predefined macros consistently,
including one correct but open-coded upper_32_bits() instance.
Fixes: d1ef4da8487f ("scsi: aacraid: added support for init_struct_8") Fixes: 423400e64d37 ("scsi: aacraid: Include HBA direct interface") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 7 Feb 2017 11:51:29 +0000 (11:51 +0000)]
scsi: aacraid: rcode is unsigned and should be signed int
aac_fib_send can return -ve error returns and hence rcode should be
signed. Currently the rcode >= 0 check is always true and -ve errors are
not being checked.
Thanks to Dan Carpenter for spotting my original broken fix to this
issue.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: remove tsk_mgmt_response and it_nexus_response transport methods
They are never called and just dispatch to methods of the same names in
the FC and SRP transport classes that are never implemented.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: remove eh_timed_out methods in the transport template
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
EH_NOT_HANDLED is the default case if no eh_timed_out method is
provided, so there is no need to supply it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These days we can specify an eh_timed_out handler in the host_template,
so don't have a transport_template definition just for it.
[mkp: fixed typo]
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the aacraid driver prefix from 1.2-1 to 1.2.1
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Retrieve HBA host information ioctl
Added a new ioctl interface to retrieve the host device information.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Added ioctl to trigger IOP/IWBR reset
Added a new ioctl interface to trigger an IOP or IWBR reset from ioctl.
Primary used by management utility to trigger resets.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added a new IWBR soft reset type, reworked the IOP reset interface for
a bit.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to retrieve the unique identifier data (VPD page
83 type3) for Logical drives created on SmartIOC 2000 products. In
addition added a sysfs device structure to expose the id information.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Added support to abort cmd and reset lun
Added task management command support to abort any timed out commands
in case of a eh_abort call and to reset lun's in case of eh_reset call.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to send out task management commands.
[mkp: removed // fibsize... ]
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to send direct pasthru srb commands from management utilty
to the controller.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Added support to set QD of attached drives
Added support to set qd of drives in slave_configure.This only works for
HBA1000 attached drives.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Retrieve Queue Depth from Adapter FW
Retrieved queue depth from fw and saved it for future use.
Only applicable for HBA1000 drives.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Added support for periodic wellness sync
This patch adds a new functions that periodically sync the time of host
to the adapter. In addition also informs the adapter that the driver is
alive and kicking. Only applicable to the HBA1000 and SMARTIOC2000.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reworked aac_command_thread into aac_process_events
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Added support for read medium error
This patch processes Raw IO read medium errors.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enables the driver to actually process the I/O, or srb replies
from adapter. In addition to any HBA1000 or SmartIOC2000 adapter events.
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the driver processes error conditions even in the fast
response path for response from the adapter.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Moved the READ and WRITE switch cases to the top. Added a default
case to the switch case and replaced duplicate scsi result value with a
macro.
The idea is that since most of scsi commands we care about performance
wise are read or write, we need to process them first.
Internally the compiler (GCC) converts a switch case into either a jump
table or a bunch of if else conditions, so placing the often used read,
write cases at the top is an effort in optimization.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Retrieve and update the device types
This patch adds support to retrieve the type of each adapter connected
device. Applicable to HBA1000 and SmartIOC2000 products
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sa_firmware adds the capability to differentiate the new SmartIOC family
of adapters from the series 8 and below.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch lays the groundwork for supporting the new HBA-1000 controller
family.A new INIT structure INIT_STRUCT_8 has been added which allows for a
variable size for MSI-x vectors among other things, and is used for both
Series-8, HBA-1000 and SmartIOC-2000.
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed duplicate code that for acquiring and releasing irqs
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Dave Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Mon, 23 Jan 2017 09:56:10 +0000 (15:26 +0530)]
scsi: mpt3sas: Updating driver version to v15.100.00.00
Updated driver version to "15.100.00.00"
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Mon, 23 Jan 2017 09:56:09 +0000 (15:26 +0530)]
scsi: mpt3sas: Fix Firmware fault state 0x2100 during heavy 4K RR FIO stress test.
Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault. So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Mon, 23 Jan 2017 09:56:08 +0000 (15:26 +0530)]
scsi: mpt3sas: Fix for Crusader to achieve product targets with SAS devices.
Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Mon, 23 Jan 2017 09:56:07 +0000 (15:26 +0530)]
scsi: mpt3sas: Added print to notify cable running at a degraded speed.
Driver processes the event MPI26_EVENT_ACTIVE_CABLE_DEGRADED when a
cable is present and is running at a degraded speed (below the SAS3 12
Gb/s rate). Prints added to inform the user that the cable is not
running at optimal speed.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Mon, 30 Jan 2017 22:05:17 +0000 (16:05 -0600)]
scsi: hpsa: remove coalescing settings for ioaccel2
- Setting coalescing has a significant negative impact on low
queue-depth performance.
- Does not help high queue-depth performance.
Signed-off-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: storvsc: remove bogus code to transfer struct scatterlist
Remove a piece of code in storvsc_queuecommand that tries to pass the
physical address of the kernel struct scatterlist pointer to the host.
Fortunately the code can't ever be reached anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Sun, 15 Jan 2017 23:50:57 +0000 (18:50 -0500)]
scsi: atari_scsi: Reset DMA during bus reset only under ST-DMA lock
The atari_scsi driver should not access Falcon DMA chip registers unless
it has acquired exclusive access to that chip. If the driver doesn't
have exclusive access then there's no need for a DMA reset as there are
no scsi commands in progress.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handle timeout or bus phase change errors that could occur when sending
the IDENTIFY message.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Sun, 15 Jan 2017 23:50:57 +0000 (18:50 -0500)]
scsi: ncr5380: Resolve various static checker warnings
Avoid various warnings from "make C=1" by annotating a couple of
unlock-then-lock sequences, replacing a zero with NULL and correcting
some type casts.
Also avoid a warning from "make W=1" by adding braces.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Sun, 15 Jan 2017 23:50:57 +0000 (18:50 -0500)]
scsi: ncr5380: Reduce #include files
The NCR5380 wrapper drivers don't export symbols or declarations and
don't actually need separate header files. Most of these header files
were removed already; only sun3_scsi.h and g_NCR5380.h remain.
Move the remaining definitions to the corresponding .c files to improve
readability and proximity. The #defines which influence the #included
core driver are no longer mixed up with unrelated #defines and #includes.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Sun, 15 Jan 2017 23:50:57 +0000 (18:50 -0500)]
scsi: ncr5380: Clean up dead code and redundant macro usage
Remove dead code inside #if 0 conditionals.
Remove the #ifdef __KERNEL__ test, since NCR5380.h has no definitions
that relate to userspace code.
Remove two redundant macro definitions which were overlooked in
commit e9db3198e08b ("sun3_scsi: Adopt NCR5380.c core driver").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Sun, 15 Jan 2017 23:50:57 +0000 (18:50 -0500)]
scsi: ncr5380: Shorten host info string by removing unused option macros
The DIFFERENTIAL and PARITY option macros are unused: no supported
hardware uses differential signalling and the core driver never
implemented parity checking. These options just waste space in the host
info string.
While we are here, fix a typo in the NCR5380_info() kernel-doc comment.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 20 Jan 2017 12:45:24 +0000 (20:45 +0800)]
scsi: hisi_sas: decrease running_req in hisi_sas_slot_task_free()
There is an issue that hisi_sas_dev.running_req is not
decremented properly for internal abort and TMF.
To resolve, only decrease running_req in hisi_sas_slot_task_free()
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 20 Jan 2017 12:45:23 +0000 (20:45 +0800)]
scsi: hisi_sas: fix probe ordering problem
There is a potential probe issue in how we trigger the hw initialisation.
Although we use 1s timer to delay hw initialisation, there is still a
potential that sas_register_ha() is not be finished before we start
the PHY init from hw->hw_init().
To avoid this issue, initialise the hw after sas_register_ha() in the
same probe context.
Note: it is not necessary to use 1s timer now (modified v2 hw only).
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Downgrade the exit print in hisi_sas_internal_task_abort()
to dbg level, as info is not required.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 20 Jan 2017 12:45:21 +0000 (20:45 +0800)]
scsi: hisi_sas: modify hard reset for directed-attached disk
Correctly set registers in v2 for root PHY hardreset for directly
attached disk.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 20 Jan 2017 12:45:20 +0000 (20:45 +0800)]
scsi: hisi_sas: downgrade refclk message
The message to inform that the controller has no refclk
is currently at warning level, which is unnecessary, so
downgrade to debug.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 20 Jan 2017 12:45:19 +0000 (20:45 +0800)]
scsi: hisi_sas: modify some values of ITCT table
Set SMP connection timeout and continue AWT timer;
Clear ITCT table when dev gone.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 20 Jan 2017 12:45:18 +0000 (20:45 +0800)]
scsi: hisi_sas: workaround v2 hw SATA IO timeout issue
The v2 SAS controller needs more time to detect channel idle
and send setup link request than SATA disk does, so it is
difficult for the SAS controller to setup an STP link. Therefore
it may cause some IO timeouts.
We need to periodically configure the SAS controller so it
doesn't receive STP setup requests from SATA disks for a while,
so IO can be sent during this period.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 17 Jan 2017 20:31:56 +0000 (12:31 -0800)]
scsi: lpfc: Fix lpfc_wwn_set return code check
When I reversed the patch to re-add the lpfc_soft_wwn parameter feature,
it re-added code that had a long-standing bug. (that's what I get I
guess :)
As Dan Carpenter pointed out - error checks looked at wrong polarity. 0
is success, -errno is failure. Updated checks.
Signed-off-by: James Smart <james.smart@broadcom.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Pittman [Thu, 12 Jan 2017 21:17:20 +0000 (16:17 -0500)]
scsi: sd: Cleaned up comment references to @sdp argument explanation.
In sd.c there are two comment references to 'struct scsi_device *sdp' as
an argument. One of the references has a typo and the other should be a
reference to 'struct device *dev' instead.
Fixed by correcting the typo in the first and changing the explanation
in the second.
Signed-off-by: John Pittman <jpittman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shyam Saini [Sat, 24 Dec 2016 10:51:07 +0000 (16:21 +0530)]
scsi: lpfc: Replace BUG() with BUG_ON()
Replace BUG() with BUG_ON() using coccinelle.
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: qla4xxx: remove two unused MSI-X related #defines
Spotted while preparing qla2xxx changes as the symbols exist in both
drivers (sigh..).
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Thu, 12 Jan 2017 01:20:03 +0000 (19:20 -0600)]
scsi: cxlflash: Cancel scheduled workers before stopping AFU
When processing an AFU asynchronous interrupt, if the action results in an
operation that requires off level processing (a link reset for example),
the worker thread is scheduled. In the meantime a reset event (i.e.: EEH)
could unmap the AFU to recover. This results in an Oops when the worker
thread tries to access the AFU mapping.
In an effort to avoid this, a mapcount was introduced in
commit b45cdbaf9f7f ("cxlflash: Resolve oops in wait_port_offline")
but due to the race condition described above, this solution is incomplete.
In order to fully resolve this problem and to simplify things, this commit
removes the mapcount solution. Instead, the scheduled worker thread is
cancelled after interrupts have been disabled and prior to the mapping
being freed.
Fixes: b45cdbaf9f7f ("cxlflash: Resolve oops in wait_port_offline") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Thu, 12 Jan 2017 01:19:47 +0000 (19:19 -0600)]
scsi: cxlflash: Cleanup prints
The usage of prints within the cxlflash driver is inconsistent. This
hinders debug and makes the driver source and log output appear sloppy.
The following cleanups help unify the prints within cxlflash:
- move all prints to dev-* where possible
- transition all hex prints to lowercase
- standardize variable prints in debug output
- derive pointers in a consistent manner
- change int to bool where appropriate
- remove superfluous data from prints and print statements that do not
make sense
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Thu, 12 Jan 2017 01:19:33 +0000 (19:19 -0600)]
scsi: cxlflash: Support SQ Command Mode
The SISLite specification outlines a new queuing model to improve
over the MMIO-based IOARRIN model that exists today. This new model
uses a submission queue that exists in host memory and is shared with
the device. Each entry in the queue is an IOARCB that describes a
transfer request. When requests are submitted, IOARCBs ('current'
position tracked in host software) are populated and the submission
queue tail pointer is then updated via MMIO to make the device aware
of the requests.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Thu, 12 Jan 2017 01:19:08 +0000 (19:19 -0600)]
scsi: cxlflash: Refactor context reset to share reset logic
As staging for supporting hardware with different context reset
registers but a similar reset procedure, refactor the existing context
reset routine to move the reset logic to a common routine. This will
allow hardware with a different reset register to leverage existing
code.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Subhash Jadavani [Wed, 11 Jan 2017 00:48:25 +0000 (16:48 -0800)]
scsi: ufs: fix arguments order some trace calls
Colin Ian King reported that with commit 7ff5ab473633 ("scsi: ufs: add
tracing support") static analysis is reporting that we may have swapped
arguments on calls to:
trace_ufshcd_runtime_resume,
trace_ufshcd_runtime_suspend,
trace_ufshcd_system_suspend,
trace_ufshcd_system_resume,
and trace_ufshcd_init
Where:
hba->uic_link_state is passed to dev_state
hba->curr_dev_pwr_mode is passed to link_state
This wasn't intentional so it's a bug. This change fixed this bug.
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: Implement the PD Map support for SAS3.5 Generic Megaraid Controllers
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: ldio_outstanding variable is not decremented in completion path
ldio outstanding variable needs to be decremented in io completion path for
iMR dual queue depth
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: Enable or Disable Fast path based on the PCI Threshold Bandwidth
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: Add the Support for SAS3.5 Generic Megaraid Controllers Capabilities
The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: SAS3.5 Generic Megaraid Controllers Fast Path for RAID 1/10 Writes
To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.
Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: EEDP Escape Mode Support for SAS3.5 Generic Megaraid Controllers
An UNMAP command on a PI formatted device will leave the Logical Block Application
Tag and Logical Block Reference Tag as all F's (for those LBAs that are unmapped).
To avoid IO errors if those LBAs are subsequently read before they are written with
valid tag fields, the MPI SCSI IO requests need to set the EEDPFlags element EEDP
Escape Mode field, Bits [7:6] appropriately. A value of 2 should be set to disable
all PI checks if the Logical Block Application Tag is 0xFFFF for PI types 1 and 2.
A value of 3 should be set to disable all PI checks if the Logical Block Application
Tag is 0xFFFF and the Logical Block Reference Tag is 0xFFFFFFFF for PI type 3.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: Add new pci device Ids for SAS3.5 Generic Megaraid Controllers
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hanjun Guo [Tue, 10 Jan 2017 12:16:43 +0000 (20:16 +0800)]
scsi: remove useless acpi functions in the header file
commit f1bc1e4c44b1 ("ata: acpi: rework the ata acpi bind support")
removed scsi_register_acpi_bus_type() and
scsi_unregister_acpi_bus_type(), but forgot to remove them in the header
file, do it now.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Winkler [Thu, 5 Jan 2017 08:45:12 +0000 (10:45 +0200)]
scsi: ufs: refactor device descriptor reading
Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.
Revamp the fixup setup:
1. Rename ufs_device_info to ufs_dev_desc as very similar name
ufs_dev_info is already in use.
2. Make the handlers static as they are not used out of the ufshdc.c
file.
[mkp: applied by hand]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reading big endian value from a buffer requires explicit cast.
Fix sparse warning:
drivers/scsi/ufs/ufshcd.c:4825:24: warning: cast to restricted __be16
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Winkler [Thu, 5 Jan 2017 08:45:10 +0000 (10:45 +0200)]
scsi: ufs: unexport descritpor reading functions
Unexport ufshcd_read_device_desc and ufshcd_read_string_desc there is no
really possibility to calling them directly outside of UFS context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Winkler [Thu, 5 Jan 2017 08:45:09 +0000 (10:45 +0200)]
scsi: ufs: ufshcd_query_descriptor_retry should be static
Fix the following compilation warning:
drivers/scsi/ufs/ufshcd.c:2076:5: warning: no previous prototype for
ufshcd_query_descriptor_retry [-Wmissing-prototypes]
Also do not export the function, it should not be used out of ufs
context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Emese Revfy [Wed, 4 Jan 2017 00:01:40 +0000 (16:01 -0800)]
scsi: esas2r: Fix format string type mistakes
This adds the missing __printf attribute which allows compile time
format string checking (and will be used by the coming initify gcc
plugin). Additionally, this fixes the warnings exposed by the attribute.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: split scsi/acpi, merged attr and fix, new commit messages] Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just call the functions directly instead of obsfucating the call chain.
This was in reply to a patch from Kees Cook to constify the function
pointer struct bfa_fcs_mod_s, but it turns out there is no reason to
have this indirection at all.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 29 Dec 2016 22:20:38 +0000 (22:20 +0000)]
scsi: qla2xxx: rename {vendor|hba}_indentifer to {vendor|hba}_identifer
Rename the vendor_indentifer and hba_indentifer fields to correct
spelling.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nicolas Iooss [Mon, 26 Dec 2016 13:23:10 +0000 (14:23 +0100)]
scsi: qla2xxx: make msix_entries const
msix_entries and qla82xx_msix_entries arrays are never modified in
drivers/scsi/qla2xxx/qla_isr.c. Move their contents to read-only data.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nicolas Iooss [Mon, 26 Dec 2016 13:23:09 +0000 (14:23 +0100)]
scsi: qla2xxx: silence -Wformat-security warning
qla24xx_enable_msix() calls scnprintf() with a non-literal format
string. This makes clang report -Wformat-security warnings when
compiling this function:
drivers/scsi/qla2xxx/qla_isr.c:3083:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[i].name);
^~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3083:7: note: treat the string as an
argument to avoid this
msix_entries[i].name);
^
"%s",
drivers/scsi/qla2xxx/qla_isr.c:3119:7: error: format string is not a
string literal (potentially insecure) [-Werror,-Wformat-security]
msix_entries[QLA_ATIO_VECTOR].name);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_isr.c:3119:7: note: treat the string as an
argument to avoid this
msix_entries[QLA_ATIO_VECTOR].name);
^
"%s",
Even though msix_entries[...].name are initialized as literal strings
with no % character and are never modified, introduce a "%s" format
parameter in order to silence this -Wformat-security warning and make
clang able to detect at compile time real bugs related to string
formatting.
[mkp: typo]
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 3 Jan 2017 12:24:50 +0000 (20:24 +0800)]
scsi: hisi_sas: lock sensitive region in hisi_sas_slot_abort()
When we call hisi_sas_slot_task_free() we should grab the hisi_hba.lock,
as hisi_sas_slot_task_free() accesses common hisi_hba elements.
Function hisi_sas_slot_abort() is missing this, so add it.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org> Tested-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 3 Jan 2017 12:24:49 +0000 (20:24 +0800)]
scsi: hisi_sas: lock sensitive regions when servicing CQ interrupt
There is a bug in the current driver in that certain hisi_hba and port
structure elements which we access when servicing the CQ interrupt do
not use thread-safe accesses; these include hisi_sas_port linked-list of
active slots (hisi_sas_port.entry), bitmap of currently allocated IPTT
(in hisi_hba.slot_index_tags), and completion queue read pointer.
As a solution, lock these elements with the hisi_hba.lock.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org> Tested-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 3 Jan 2017 12:24:48 +0000 (20:24 +0800)]
scsi: hisi_sas: service v2 hw CQ ISR with tasklet
Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).
So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org> Tested-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
$
After this patch:
$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
alias: of:N*T*Cqcom,ufshcC*
alias: of:N*T*Cqcom,ufshc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dolev Raviv [Fri, 23 Dec 2016 02:42:18 +0000 (18:42 -0800)]
scsi: ufs: Improve fatal error logs
Errors such as UIC error, illegal OCS values, and others may require
more information for debugging. Such information could be hibern8 events,
events sequences, recoverable errors, error history, and more.
This patch improves tracking of important errors and events in debug level
to be enabled when debugging a such issues. It includes:
* UIC error history
* Successful hibern8 events
* Successful command after hibern8 exit
* Clk-freq info
* Failed device command
* Infrastructure for dumping host controller debug information
Signed-off-by: Dolev Raviv <draviv@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lee Susman [Fri, 23 Dec 2016 02:42:03 +0000 (18:42 -0800)]
scsi: ufs: add trace event for ufs commands
Use the ftrace infrastructure to conditionally trace ufs command events.
New trace event is created, which samples the following ufs command data:
- device name
- optional identification string
- task tag
- doorbell register
- number of transfer bytes
- interrupt status register
- request start LBA
- command opcode
Currently we only fully trace read(10) and write(10) commands.
All other commands which pass through ufshcd_send_command() will be
printed with "-1" in the lba and transfer_len fields.
Signed-off-by: Lee Susman <lsusman@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>