Akinobu Mita [Thu, 20 Jul 2017 15:24:18 +0000 (00:24 +0900)]
iio: adc: ti-ads1015: fix scale information for ADS1115
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Akinobu Mita [Thu, 20 Jul 2017 15:24:17 +0000 (00:24 +0900)]
iio: adc: ti-ads1015: fix incorrect data rate setting update
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Fri, 28 Jul 2017 22:20:14 +0000 (01:20 +0300)]
iio: adc: ti-ads7950: Allow to use on ACPI platforms
ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we
fall back to request a regulator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Arvind Yadav [Sat, 19 Aug 2017 18:47:38 +0000 (00:17 +0530)]
iio: light: tsl2583: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Arvind Yadav [Sat, 19 Aug 2017 18:47:37 +0000 (00:17 +0530)]
iio: light: apds9300: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Arvind Yadav [Sat, 19 Aug 2017 18:47:36 +0000 (00:17 +0530)]
iio: accel: bma180: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: chemical: ccs811: Add triggered buffer support
A software trigger such as hrtimer can be used to capture the data
that will be stored in the buffer.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andreas Klinger [Wed, 16 Aug 2017 19:34:23 +0000 (21:34 +0200)]
iio: srf08: add sensor type srf10
Ultrasonic sensor srf10 is quite similar to srf08 and now also supported by
the driver as device tree compatible string.
It was necessary to prepare the source for supplementary sensors. This is
done by enum srf08_sensor_type.
The most significiant difference between srf08 and srf10 is another range
and values of register gain (in the driver it's call sensitivity).
Therefore the array of it is extended and dependent of the sensor type.
Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Arnd Bergmann [Tue, 15 Aug 2017 14:46:31 +0000 (16:46 +0200)]
iio: adc: select triggered buffer for sama5d2 adc
Without the triggered buffer code, we get a link error:
drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8c9 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Fri, 11 Aug 2017 19:44:14 +0000 (21:44 +0200)]
iio: accel: st_accel: fix data-ready line configuration
Remove int2 configuration parameter for LIS3DH, LSM303DLHC, LSM330D,
LSM330DL, LSM330DLC, LSM303AGR, LIS2DH12 and LNG2DM since these devices
export just int1 as data-ready line
Fixes: 23cde4d65cc7 (iio: Added platform data to select the DRDY pin) Fixes: dcdb0a78cab3 (iio: accel: st_accel: add support to lng2dm) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fix following checkpatch warnings in xadc driver
1. prefer 'unsigned int' to bare use of 'unsigned'.
2. else is not generally useful after a break or return.
3. fill all function definition arguments with identifier name
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
staging: iio: adc: fix error return code in ad7606_par_probe()
platform_get_irq() returns an error code, but the ad7606_par driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Yan [Wed, 2 Aug 2017 08:52:33 +0000 (16:52 +0800)]
dt-bindings: adc: add description for rv1108 saradc
Add device tree bindings document for saradc on
rockchip rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier [Thu, 3 Aug 2017 09:14:13 +0000 (11:14 +0200)]
iio: trigger: stm32-timer: add support for STM32H7
Add support for STM32H7 timer triggers:
- Add new valids_table
- Introduce compatible, with configuration data
- Extend up to 15 timers, available on STM32H7
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Fri, 28 Jul 2017 22:20:15 +0000 (01:20 +0300)]
iio: adc: ti-ads7950: Add OF device ID table
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI device registered via OF will always match a legacy SPI device ID and
that the MODALIAS reported will always be of the form spi:<device>.
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Besides this could change in the future so the correct approach is to
have an OF device ID table if the devices are registered via OF.
Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32 ADC allows each channel to be sampled with a different sampling time,
by setting SMPR registers. Basically, value depends on local electrical
properties. Selecting correct value for sampling time highly depends on
analog source impedance. There is a manual that may help in this process:
'How to get the best ADC accuracy in STM32...'
This patch allows to configure minimum sampling time via device tree,
either for:
- all channels at once:
st,min-sample-time-nsecs = <10000>;
- independently for each channel (must match "st,adc-channels" list):
st,adc-channels = <0 1>;
st,min-sample-time-nsecs = <5000 10000>;
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32 ADC allows each channel to be sampled with a different sampling
time. There's an application note that deals with this: 'How to get
the best ADC accuracy in STM32...' It basically depends on analog input
signal electrical properties (depends on board).
Add optional 'st,min-sample-time-nsecs' property so this can be tuned
in dt.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jacob von Chorus [Fri, 28 Jul 2017 21:06:17 +0000 (17:06 -0400)]
staging: gs_fpgaboot: change char to u8
The bitstream storage variables were changed from char to u8 arrays to
prevent issues such as negative lengths. This change makes the code
compatible with the "data" field in "struct firmware" which is of type
u8.
Signed-off-by: Jacob von Chorus <jacobvonchorus@cwphoto.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacob von Chorus [Fri, 28 Jul 2017 21:06:16 +0000 (17:06 -0400)]
staging: gs_fpgaboot: add buffer overflow checks
Four fields in struct fpgaimage are char arrays of length MAX_STR (256).
The amount of data read into these buffers is controlled by a length
field in the bitstream file read from userspace. If a corrupt or
malicious firmware file was supplied, kernel data beyond these buffers
can be overwritten arbitrarily.
This patch adds a check of the bitstream's length value to ensure it
fits within the bounds of the allocated buffers. An error condition is
returned from gs_read_bitstream if any of the reads fail.
Signed-off-by: Jacob von Chorus <jacobvonchorus@cwphoto.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Wed, 19 Jul 2017 09:36:16 +0000 (10:36 +0100)]
staging: vboxvideo: make a couple of symbols static
Module parameter vbox_modeset and structure vbox_bo_driver do not need to
be in global scope and hence can be made static.
Cleans up a couple of sparse warnings:
symbol 'vbox_modeset' was not declared. Should it be static?
symbol 'vbox_bo_driver' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Michael Thayer <michael.thayer@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Cretaro [Sat, 22 Jul 2017 10:55:53 +0000 (12:55 +0200)]
staging: vboxvideo: remove unused variables
Fix compiler warnings:
vbox_mode.c:57:15: warning: variable ‘crtc_id’ set but not used
vbox_mode.c:581:25: warning: variable ‘vbox_connector’ set but not used
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Michael Thayer <michael.thayer@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: vboxvideo: Kconfig: Fix typos in help text
This fixes typos in vboxvideo's help text. Most notably, "to builtin
this module" becomes "to build this driver built-in to the kernel".
Signed-off-by: Martin Kepplinger <martink@posteo.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 25 Jul 2017 08:50:46 +0000 (10:50 +0200)]
staging: vboxvideo: select GENERIC_ALLOCATOR
The vboxvideo code uses various gen_pool_* functions, so it needs
lib/genalloc.c to be built. In some configs this is not happening,
so add select GENERIC_ALLOCATOR to the Kconfig file to enforce this.
Note all other Kconfig references to GENERIC_ALLOCATOR also use select.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/pi433/rf69.o: In function `rf69_set_frequency':
rf69.c:(.text+0xc9c): undefined reference to `__udivdi3'
No idea why I didn't see it with the default EABI configurations,
but the right solution here seems to be to use div_u64()
to get the external division implementation.
Colin Ian King [Tue, 18 Jul 2017 13:03:59 +0000 (14:03 +0100)]
staging: pi433: Make functions rf69_set_bandwidth_intern static
The function rf69_set_bandwidth_intern is local to the source
and do not need to be in global scope, so make it static. Also
break overly wide line.
Cleans up sparse warning:
symbol 'update_share_count' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Marcus Wolf <linux@wolf-entwicklungen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joseph Wright [Sun, 16 Jul 2017 14:48:58 +0000 (14:48 +0000)]
Staging: pi433: check error after kthread_run()
Error should be checked with IS_ERR after calling kthread_run()
instead of comparing the returned pointer to an int.
Found by sparse warning:
incompatible types for operation (<)
left side has type struct task_struct *tx_task_struct
right side has type int
Signed-off-by: Joseph Wright <rjosephwright@gmail.com> Reviewed-by: Marcus Wolf <linux@wolf-entwicklungen.de> Tested-by: Marcus Wolf <linux@wolf-entwicklungen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joseph Wright [Sun, 16 Jul 2017 14:48:57 +0000 (14:48 +0000)]
Staging: pi433: declare functions static
Declare functions static to fix sparse warnings:
warning: symbol 'pi433_receive' was not declared. Should it be static?
warning: symbol 'pi433_tx_thread' was not declared. Should it be static?
Signed-off-by: Joseph Wright <rjosephwright@gmail.com> Reviewed-by: Marcus Wolf <linux@wolf-entwicklungen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Wed, 19 Jul 2017 23:58:28 +0000 (16:58 -0700)]
staging: pi433: depends on SPI
The pi433 driver uses SPI interfaces so it should depend on SPI.
Also, the "default n" can be removed since that is already the
default.
Fixes these build errors when SPI is not enabled:
drivers/staging/pi433/pi433_if.o: In function `pi433_probe':
pi433_if.c:(.text+0x1135): undefined reference to `spi_setup'
pi433_if.c:(.text+0x1177): undefined reference to `spi_write_then_read'
drivers/staging/pi433/pi433_if.o: In function `pi433_init':
pi433_if.c:(.init.text+0xb8): undefined reference to `__spi_register_driver'
drivers/staging/pi433/rf69.o: In function `rf69_read_fifo':
rf69.c:(.text+0x102): undefined reference to `spi_sync'
drivers/staging/pi433/rf69.o: In function `rf69_write_fifo':
rf69.c:(.text+0x248): undefined reference to `spi_sync'
drivers/staging/pi433/rf69.o: In function `rf69_read_reg':
rf69.c:(.text+0x290): undefined reference to `spi_write_then_read'
drivers/staging/pi433/rf69.o: In function `rf69_write_reg':
rf69.c:(.text+0x523): undefined reference to `spi_sync'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Marcus Wolf <linux@wolf-entwicklungen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Ian King [Fri, 21 Jul 2017 13:42:52 +0000 (14:42 +0100)]
staging: rtl8192u: fix incorrect mask and shift on u8 data
The cfg_action bit comes from the high bit of pmsg[4] so the
current mask and shift are in correct and always result in
zero. Fix this by using the correct mask and shif to get the
correct cfg_action bit value.
Detected by CoverityScan, CID#142890 ("Operands don't affect result")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary platform_set_drvdata() has been removed since the driver
core clears the driver data to NULL after device release or on
probe failure. There is no need to manually clear the device
driver data to NULL.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
struct platform_device *pdev;
@@
- platform_set_drvdata(pdev, NULL);
//</smpl>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
Lorenzo Bianconi [Mon, 17 Jul 2017 17:39:04 +0000 (19:39 +0200)]
dt-bindings: iio: humidity: hts221: support open drain mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a perl script to actually parse the MAINTAINERS file, clean up
some whitespace in it, warn about errors in it, and then properly sort
the end result.
My perl-fu is atrocious, so the script has basically been created by
randomly putting various characters in a pile, mixing them around, and
then looking it the end result does anything interesting when used as a
perl script.
Prepping for scripting the MAINTAINERS file cleanup (and possible split)
showed a couple of cases where the headers for a couple of entries were
bogus.
There's a few different kinds of bogosities:
- the X-GENE SOC EDAC case was confused and split over two lines
- there were four entries for "GREYBUS PROTOCOLS DRIVERS" that were all
different things.
- the NOKIA N900 CAMERA SUPPORT" was duplicated
all of which were more obvious when you started doing associative arrays
in perl to track these things by the header (so that we can alphabetize
this thing properly, and so that we might split it up by the data too).
Cc: Joe Perches <joe@perches.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'for-linus-4.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some fixes and cleanups for running under Xen"
* tag 'for-linus-4.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: don't online new memory initially
xen/x86: fix cpu hotplug
xen/grant-table: log the lack of grants
xen/x86: Don't BUG on CPU0 offlining
When setting up the Xenstore watch for the memory target size the new
watch will fire at once. Don't try to reach the configured target size
by onlining new memory in this case, as the current memory size will
be smaller in almost all cases due to e.g. BIOS reserved pages.
Onlining new memory will lead to more problems e.g. undesired conflicts
with NVMe devices meant to be operated as block devices.
Instead remember the difference between target size and current size
when the watch fires for the first time and apply it to any further
size changes, too.
In order to avoid races between balloon.c and xen-balloon.c init calls
do the xen-balloon.c initialization from balloon.c.
Commit dc6416f1d711eb4c1726e845d653235dcaae12e1 ("xen/x86: Call
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()")
introduced an error leading to a stack overflow of the idle task when
a cpu was brought offline/online many times: by calling
cpu_startup_entry() instead of returning at the end of xen_play_dead()
do_idle() would be entered again and again.
Don't use cpu_startup_entry(), but cpuhp_online_idle() instead allowing
to return from xen_play_dead().
Wengang Wang [Tue, 18 Jul 2017 07:40:35 +0000 (09:40 +0200)]
xen/grant-table: log the lack of grants
log a message when we enter this situation:
1) we already allocated the max number of available grants from hypervisor
and
2) we still need more (but the request fails because of 1)).
Sometimes the lack of grants causes IO hangs in xen_blkfront devices.
Adding this log would help debuging.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
Vitaly Kuznetsov [Mon, 26 Jun 2017 16:39:30 +0000 (18:39 +0200)]
xen/x86: Don't BUG on CPU0 offlining
CONFIG_BOOTPARAM_HOTPLUG_CPU0 allows to offline CPU0 but Xen HVM guests
BUG() in xen_teardown_timer(). Remove the BUG_ON(), this is probably a
leftover from ancient times when CPU0 hotplug was impossible, it works
just fine for HVM.
Rob Herring [Tue, 18 Jul 2017 21:43:08 +0000 (16:43 -0500)]
iio: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: linux-iio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Mon, 17 Jul 2017 17:39:02 +0000 (19:39 +0200)]
dt-bindings: iio: humidity: hts221: support active-low interrupts
Update hts221 device binding with active-low interrupts support
(IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING).
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Mon, 17 Jul 2017 17:39:01 +0000 (19:39 +0200)]
iio: humidity: hts221: support active-low interrupts
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi [Mon, 17 Jul 2017 17:38:58 +0000 (19:38 +0200)]
iio: humidity: hts221: do not overwrite reserved data during power-down
GENMASK(6, 3) in CTRL_REG1 and GENMASK(6, 2) in CTRL_REG2 are marked
reserved. Do not changed the original value (not declared in the
datasheet) during power-down/suspend routines.
Fixes: e4a70e3e7d84 (iio: humidity: add support to hts221 rh/temp device) Fixes: b7079eeac5da (iio: humidity: hts221: add power management support) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: chemical: ccs811: Add support for AMS CCS811 VOC sensor
Add support for CCS811 VOC sensor. This patch adds support
for reading current and voltage across the sensor and TVOC
and equivalent CO2 values.
Scale and offset values have been computed according to datasheet:
- For current: raw value is in microamps
=> 0.001 scale to convert to milliamps
- For voltage: 1.65V = 1023, therefore 1650mV = 1023
=> 1650.0/1023 = 1.612903 scale to convert to millivolts
- For eCO2: raw value range is from 400ppm to 8192ppm.
=> (val - 400) * (100 - 0) / (8192 - 400) + 0 =
(val - 400) * 0.01283367 => offset: -400, scale = 0.012834
to get a percentage value
-For TVOC: raw value range is from 0ppb to 1187ppb.
=> (val - 0) * 100 / (1187 - 0) + 0 = val * 0.0842459 =>
scale = 0.084246 for getting a percentage value
Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Merge tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
huge at all, a revert of a patch that turned out to break things, a
fix up for a new tty ioctl we added in 4.13-rc1 to get the uapi
definition correct, and a few minor serial driver fixes for reported
issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix TIOCGPTPEER ioctl definition
tty: hide unused pty_get_peer function
tty: serial: lpuart: Fix the logic for detecting the 32-bit type UART
serial: imx: Prevent TX buffer PIO write when a DMA has been started
Revert "serial: imx-serial - move DMA buffer configuration to DT"
serial: sh-sci: Uninitialized variables in sysfs files
serial: st-asc: Potential error pointer dereference
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for 4.13-rc2. All fix
reported problems with 4.13-rc1 or older kernels (like the binder
fixes). Full details in the shortlog.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
w1: omap-hdq: fix error return code in omap_hdq_probe()
regmap: regmap-w1: Fix build troubles
w1: Fix slave count on 1-Wire bus (resend)
mux: mux-core: unregister mux_class in mux_exit()
mux: remove the Kconfig question for the subsystem
nvmem: rockchip-efuse: amend compatible rk322x-efuse to rk3228-efuse
drivers/fsi: fix fsi_slave_mode prototype
fsi: core: register with postcore_initcall
thunderbolt: Correct access permissions for active NVM contents
vmbus: re-enable channel tasklet
spmi: pmic-arb: Always allocate ppid_to_apid table
MAINTAINERS: Add entry for SPMI subsystem
spmi: Include OF based modalias in device uevent
binder: Use wake up hint for synchronous transactions.
binder: use group leader instead of open thread
Revert "android: binder: Sanity check at binder ioctl"
Merge tag 'usb-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.13-rc2.
The usual batch, gadget fixes for reported issues, as well as xhci
fixes, and a small random collection of other fixes for reported
issues.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
xhci: fix memleak in xhci_run()
usb: xhci: fix spinlock recursion for USB2 test mode
xhci: fix 20000ms port resume timeout
usb: xhci: Issue stop EP command only when the EP state is running
xhci: Bad Ethernet performance plugged in ASM1042A host
xhci: Fix NULL pointer dereference when cleaning up streams for removed host
usb: renesas_usbhs: gadget: disable all eps when the driver stops
usb: renesas_usbhs: fix usbhsc_resume() for !USBHSF_RUNTIME_PWCTRL
usb: gadget: udc: renesas_usb3: protect usb3_ep->started in usb3_start_pipen()
usb: gadget: udc: renesas_usb3: fix zlp transfer by the dmac
usb: gadget: udc: renesas_usb3: fix free size in renesas_usb3_dma_free_prd()
usb: gadget: f_uac2: endianness fixes.
usb: gadget: f_uac1: endianness fixes.
include: usb: audio: specify exact endiannes of descriptors
usb: gadget: udc: start_udc() can be static
usb: dwc2: gadget: On USB RESET reset device address to zero
usb: storage: return on error to avoid a null pointer dereference
usb: typec: include linux/device.h in ucsi.h
USB: cdc-acm: add device-id for quirky printer
usb: dwc3: gadget: only unmap requests from DMA if mapped
...
Merge tag 'staging-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for reported issues for
4.13-rc2.
Also in here is a new driver, the virtualbox DRM driver. It's
stand-alone and got acks from the DRM developers to go in through this
tree. It's a new thing, but it should be fine for this point in the rc
cycle due to it being independent.
All of this has been in linux-next for a while with no reported
issues"
* tag 'staging-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8188eu: add TL-WN722N v2 support
staging: speakup: safely register and unregister ldisc
staging: speakup: add functions to register and unregister ldisc
staging: speakup: safely close tty
staging: sm750fb: avoid conflicting vesafb
staging: lustre: ko2iblnd: check copy_from_iter/copy_to_iter return code
staging: vboxvideo: Add vboxvideo to drivers/staging
staging: sm750fb: fixed a assignment typo
staging: rtl8188eu: memory leak in rtw_free_cmd_obj()
staging: vchiq_arm: fix error codes in probe
staging: comedi: ni_mio_common: fix AO timer off-by-one regression
Randy Dunlap [Fri, 21 Jul 2017 20:32:27 +0000 (13:32 -0700)]
MAINTAINERS: fix alphabetical ordering
Fix major alphabetic errors. No attempt to fix items that all begin
with the same word (like ARM, BROADCOM, DRM, EDAC, FREESCALE, INTEL,
OMAP, PCI, SAMSUNG, TI, USB, etc.).
(diffstat +/- is different by one line because TI KEYSTONE MULTICORE
had 2 blank lines after it.)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'nfs-for-4.13-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"Stable bugfix:
- Fix error reporting regression
Bugfixes:
- Fix setting filelayout ds address race
- Fix subtle access bug when using ACLs
- Fix setting mnt3_counts array size
- Fix a couple of pNFS commit races"
* tag 'nfs-for-4.13-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS/filelayout: Fix racy setting of fl->dsaddr in filelayout_check_deviceid()
NFS: Be more careful about mapping file permissions
NFS: Store the raw NFS access mask in the inode's access cache
NFSv3: Convert nfs3_proc_access() to use nfs_access_set_mask()
NFS: Refactor NFS access to kernel access mask calculation
net/sunrpc/xprt_sock: fix regression in connection error reporting.
nfs: count correct array for mnt3_counts array size
Revert commit 722f0b891198 ("pNFS: Don't send COMMITs to the DSes if...")
pNFS/flexfiles: Handle expired layout segments in ff_layout_initiate_commit()
NFS: Fix another COMMIT race in pNFS
NFS: Fix a COMMIT race in pNFS
mount: copy the port field into the cloned nfs_server structure.
NFS: Don't run wake_up_bit() when nobody is waiting...
nfs: add export operations
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This fixes a crash with SELinux and several other old and new bugs"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: check for bad and whiteout index on lookup
ovl: do not cleanup directory and whiteout index entries
ovl: fix xattr get and set with selinux
ovl: remove unneeded check for IS_ERR()
ovl: fix origin verification of index dir
ovl: mark parent impure on ovl_link()
ovl: fix random return value on mount
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small set of fixes for -rc2 - two fixes for BFQ, documentation and
code, and a removal of an unused variable in nbd. Outside of that, a
small collection of fixes from the usual crew on the nvme side"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: don't report 0-bytes in serial number
nvmet: preserve controller serial number between reboots
nvmet: Move serial number from controller to subsystem
nvmet: prefix version configfs file with attr
nvme-pci: Fix an error handling path in 'nvme_probe()'
nvme-pci: Remove nvme_setup_prps BUG_ON
nvme-pci: add another device ID with stripe quirk
nvmet-fc: fix byte swapping in nvmet_fc_ls_create_association
nvme: fix byte swapping in the streams code
nbd: kill unused ret in recv_work
bfq: dispatch request to prevent queue stalling after the request completion
bfq: fix typos in comments about B-WF2Q+ algorithm
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma fixes from Doug Ledford:
"As per my previous pull request, there were two drivers that each had
a rather large number of legitimate fixes still to be sent.
As it turned out, I also missed a reasonably large set of fixes from
one person across the stack that are all important fixes. All in all,
the bnxt_re, i40iw, and Dan Carpenter are 3/4 to 2/3rds of this pull
request.
There were some other random fixes that I didn't send in the last pull
request that I added to this one. This catches the rdma stack up to
the fixes from up to about the beginning of this week. Any more fixes
I'll wait and batch up later in the -rc cycle. This will give us a
good base to start with for basing a for-next branch on -rc2.
Summary:
- i40iw fixes
- bnxt_re fixes
- Dan Carpenter bugfixes across stack
- ten more random fixes, no more than two from any one person"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
RDMA/core: Initialize port_num in qp_attr
RDMA/uverbs: Fix the check for port number
IB/cma: Fix reference count leak when no ipv4 addresses are set
RDMA/iser: don't send an rkey if all data is written as immadiate-data
rxe: fix broken receive queue draining
RDMA/qedr: Prevent memory overrun in verbs' user responses
iw_cxgb4: don't use WR keys/addrs for 0 byte reads
IB/mlx4: Fix CM REQ retries in paravirt mode
IB/rdmavt: Setting of QP timeout can overflow jiffies computation
IB/core: Fix sparse warnings
RDMA/bnxt_re: Fix the value reported for local ack delay
RDMA/bnxt_re: Report MISSED_EVENTS in req_notify_cq
RDMA/bnxt_re: Fix return value of poll routine
RDMA/bnxt_re: Enable atomics only if host bios supports
RDMA/bnxt_re: Specify RDMA component when allocating stats context
RDMA/bnxt_re: Fixed the max_rd_atomic support for initiator and destination QP
RDMA/bnxt_re: Report supported value to IB stack in query_device
RDMA/bnxt_re: Do not free the ctx_tbl entry if delete GID fails
RDMA/bnxt_re: Fix WQE Size posted to HW to prevent it from throwing error
RDMA/bnxt_re: Free doorbell page index (DPI) during dealloc ucontext
...
Merge tag 'trace-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three minor updates
- Use the new GFP_RETRY_MAYFAIL to be more aggressive in allocating
memory for the ring buffer without causing OOMs
- Fix a memory leak in adding and removing instances
- Add __rcu annotation to be able to debug RCU usage of function
tracing a bit better"
* tag 'trace-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
trace: fix the errors caused by incompatible type of RCU variables
tracing: Fix kmemleak in instance_rmdir
tracing/ring_buffer: Try harder to allocate
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"A bunch of small fixes for x86"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: hyperv: avoid livelock in oneshot SynIC timers
KVM: VMX: Fix invalid guest state detection after task-switch emulation
x86: add MULTIUSER dependency for KVM
KVM: nVMX: Disallow VM-entry in MOV-SS shadow
KVM: nVMX: track NMI blocking state separately for each VMCS
KVM: x86: masking out upper bits