The swap code already uses synchronous discards, no need to add I/O
barriers.
This fixes the worst of the terrible slowdown in swap allocation for
hibernation, reported on 2.6.35 by Nigel Cunningham; but does not entirely
eliminate that regression.
Move the hibernation check from scan_swap_map() into try_to_free_swap():
to catch not only the common case when hibernation's allocation itself
triggers swap reuse, but also the less likely case when concurrent page
reclaim (shrink_page_list) might happen to try_to_free_swap from a page.
Hibernation already clears __GFP_IO from the gfp_allowed_mask, to stop
reclaim from going to swap: check that to prevent swap reuse too.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Ondrej Zary <linux@rainbow-software.org> Cc: Andrea Gelmini <andrea.gelmini@gmail.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nigel Cunningham <nigel@tuxonice.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Please revert 2.6.36-rc commit d2997b1042ec150616c1963b5e5e919ffd0b0ebf
"hibernation: freeze swap at hibernation". It complicated matters by
adding a second swap allocation path, just for hibernation; without in any
way fixing the issue that it was intended to address - page reclaim after
fixing the hibernation image might free swap from a page already imaged as
swapcache, letting its swap be reallocated to store a different page of
the image: resulting in data corruption if the imaged page were freed as
clean then swapped back in. Pages freed to si->swap_map were still in
danger of being reallocated by the alternative allocation path.
I guess it inadvertently fixed slow SSD swap allocation for hibernation,
as reported by Nigel Cunningham: by missing out the discards that occur on
the usual swap allocation path; but that was unintentional, and needs a
separate fix.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Ondrej Zary <linux@rainbow-software.org> Cc: Andrea Gelmini <andrea.gelmini@gmail.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nigel Cunningham <nigel@tuxonice.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gary King [Thu, 9 Sep 2010 23:38:05 +0000 (16:38 -0700)]
bounce: call flush_dcache_page() after bounce_copy_vec()
I have been seeing problems on Tegra 2 (ARMv7 SMP) systems with HIGHMEM
enabled on 2.6.35 (plus some patches targetted at 2.6.36 to perform cache
maintenance lazily), and the root cause appears to be that the mm bouncing
code is calling flush_dcache_page before it copies the bounce buffer into
the bio.
The bounced page needs to be flushed after data is copied into it, to
ensure that architecture implementations can synchronize instruction and
data caches if necessary.
Signed-off-by: Gary King <gking@nvidia.com> Cc: Tejun Heo <tj@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Acked-by: Jens Axboe <axboe@kernel.dk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Thu, 9 Sep 2010 23:38:03 +0000 (16:38 -0700)]
gpio: doc updates
There's been some recent confusion about error checking GPIO numbers.
briefly, it should be handled mostly during setup, when gpio_request() is
called, and NEVER by expectig gpio_is_valid to report more than
never-usable GPIO numbers.
[akpm@linux-foundation.org: terminate unterminated comment] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Eric Miao" <eric.y.miao@gmail.com> Cc: "Ryan Mallon" <ryan@bluewatersys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio: sx150x: correct and refine reset-on-probe behavior
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org> Reviewed-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory hotplug: fix next block calculation in is_removable
next_active_pageblock() is for finding next _used_ freeblock. It skips
several blocks when it finds there are a chunk of free pages lager than
pageblock. But it has 2 bugs.
1. We have no lock. page_order(page) - pageblock_order can be minus.
2. pageblocks_stride += is wrong. it should skip page_order(p) of pages.
Minchan Kim [Thu, 9 Sep 2010 23:38:00 +0000 (16:38 -0700)]
mm: compaction: handle active and inactive fairly in too_many_isolated
Iram reported that compaction's too_many_isolated() loops forever.
(http://www.spinics.net/lists/linux-mm/msg08123.html)
The meminfo when the situation happened was inactive anon is zero. That's
because the system has no memory pressure until then. While all anon
pages were in the active lru, compaction could select active lru as well
as inactive lru. That's a different thing from vmscan's isolated. So we
has been two too_many_isolated.
While compaction can isolate pages in both active and inactive, current
implementation of too_many_isolated only considers inactive. It made
Iram's problem.
This patch handles active and inactive fairly. That's because we can't
expect where from and how many compaction would isolated pages.
This patch changes (nr_isolated > nr_inactive) with
nr_isolated > (nr_active + nr_inactive) / 2.
Ira W. Snyder [Thu, 9 Sep 2010 23:37:58 +0000 (16:37 -0700)]
arch/powerpc/include/asm/fsldma.h needs slab.h
The slab.h header is required to use the kmalloc() family of functions.
Due to recent kernel changes, this header must be directly included by
code that calls into the memory allocator.
Without this patch, any code which includes this header fails to build.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: m41t80: do not use rtc_valid_tm in m41t80_rtc_read_alarm
Commit b485fe5ea ("rtc/m41t80: use rtc_valid_tm() to check returned tm")
added rtc_valid_tm to m41t80_rtc_read_alarm() but it was wrong while the
t->time does not contain complete date/time.
This patch also fixes a warning:
warning: passing argument 1 of 'rtc_valid_tm' from incompatible pointer type
Jan Sembera [Thu, 9 Sep 2010 23:37:54 +0000 (16:37 -0700)]
binfmt_misc: fix binfmt_misc priority
Commit 74641f584da ("alpha: binfmt_aout fix") (May 2009) introduced a
regression - binfmt_misc is now consulted after binfmt_elf, which will
unfortunately break ia32el. ia32 ELF binaries on ia64 used to be matched
using binfmt_misc and executed using wrapper. As 32bit binaries are now
matched by binfmt_elf before bindmt_misc kicks in, the wrapper is ignored.
The fix increases precedence of binfmt_misc to the original state.
Signed-off-by: Jan Sembera <jsembera@suse.cz> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net Cc: <stable@kernel.org> [2.6.everything.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
COMPACTION enables MIGRATION, but MIGRATION spawns a warning if numa or
memhotplug aren't selected. However MIGRATION doesn't depend on them. I
guess it's just trying to be strict doing a double check on who's enabling
it, but it doesn't know that compaction also enables MIGRATION.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pte_same check is reliable only if the swap entry remains pinned (by
the page lock on swapcache). We've also to ensure the swapcache isn't
removed before we take the lock as try_to_free_swap won't care about the
page pin.
One of the possible impacts of this patch is that a KSM-shared page can
point to the anon_vma of another process, which could exit before the page
is freed.
This can leave a page with a pointer to a recycled anon_vma object, or
worse, a pointer to something that is no longer an anon_vma.
[riel@redhat.com: changelog help] Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Thu, 9 Sep 2010 23:37:50 +0000 (16:37 -0700)]
drivers/mmc/host/imxmmc.c: adjust confusing if indentation
Move the second if (reg & ...) test into the branch indicated by its
indentation. The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Pavel Pisa <ppisa@pikron.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ethan Du [Thu, 9 Sep 2010 23:37:49 +0000 (16:37 -0700)]
omap hsmmc: fix a racing case between kmmcd and omap_hsmmc_suspend
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus] Signed-off-by: Ethan <ethan.too@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org> Acked-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmc: at91_mci: add missing linux/highmem.h include
Fix the following error:
at91_mci.c: In function 'at91_mci_sg_to_dma':
at91_mci.c:236: error: implicit declaration of function 'kmap_atomic'
at91_mci.c:236: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:236: error: (Each undeclared identifier is reported only once
at91_mci.c:236: error: for each function it appears in.)
at91_mci.c:236: warning: assignment makes pointer from integer without a cast
at91_mci.c:252: error: implicit declaration of function 'kunmap_atomic'
at91_mci.c: In function 'at91_mci_post_dma_read':
at91_mci.c:302: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:302: warning: assignment makes pointer from integer without a cast
at91_mci.c:317: error: implicit declaration of function 'flush_kernel_dcache_page'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() takes the cookie, returned by the kmap_atomic() as its
argument and not the page address, used as an argument to kmap_atomic().
This patch fixes the compile error:
In file included from drivers/mmc/host/tmio_mmc.c:37:
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:192: error: negative width in bit-field '<anonymous>'
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Eric Miao <eric.y.miao@gmail.com> Tested-by: Magnus Damm <damm@opensource.se> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, it was possible for ack_mmc_irqs() to clear pending interrupt
bits in the CTL_STATUS register, even though the interrupt handler had not
been called. This was because of a race that existed when doing a
read-modify-write sequence on CTL_STATUS. After the read step in this
sequence, if an interrupt occurred (causing one of the bits in CTL_STATUS
to be set) the write step would inadvertently clear it.
Observed with the TMIO_STAT_RXRDY bit together with CMD53 on AR6002 and
BCM4318 SDIO cards in polled mode.
This patch eliminates this race by only writing to CTL_STATUS and clearing
the interrupts that were passed as an argument to ack_mmc_irqs()."
[matt@console-pimps.org: rewrote changelog] Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Acked-by: Magnus Damm <damm@opensource.se>" Tested-by: Arnd Hannemann <arnd@arndnet.de>" Acked-by: Ian Molton <ian@mnementh.co.uk> Cc: Matt Fleming <matt@console-pimps.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The existing cgroup_attach_task_current_cg() API is called by a thread to
attach another thread to all of its cgroups; this is unsuitable for cases
where a privileged task wants to attach itself to the cgroups of a less
privileged one, since the call must be made from the context of the target
task.
This patch adds a more generic cgroup_attach_task_all() API that allows
both the source task and to-be-moved task to be specified.
cgroup_attach_task_current_cg() becomes a specialization of the more
generic new function.
[menage@google.com: rewrote changelog]
[akpm@linux-foundation.org: address reviewer comments] Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Paul Menage <menage@google.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Ben Blum <bblum@google.com> Cc: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcov: fix null-pointer dereference for certain module types
The gcov-kernel infrastructure expects that each object file is loaded
only once. This may not be true, e.g. when loading multiple kernel
modules which are linked to the same object file. As a result, loading
such kernel modules will result in incorrect gcov results while unloading
will cause a null-pointer dereference.
This patch fixes these problems by changing the gcov-kernel infrastructure
so that multiple profiling data sets can be associated with one debugfs
entry. It applies to 2.6.36-rc1.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reported-by: Werner Spies <werner.spies@thalesgroup.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Moyer [Thu, 9 Sep 2010 23:37:33 +0000 (16:37 -0700)]
O_DIRECT: fix the splitting up of contiguous I/O
commit c2c6ca4 (direct-io: do not merge logically non-contiguous requests)
introduced a bug whereby all O_DIRECT I/Os were submitted a page at a time
to the block layer. The problem is that the code expected
dio->block_in_file to correspond to the current page in the dio. In fact,
it corresponds to the previous page submitted via submit_page_section.
This was purely an oversight, as the dio->cur_page_fs_offset field was
introduced for just this purpose. This patch simply uses the correct
variable when calculating whether there is a mismatch between contiguous
logical blocks and contiguous physical blocks (as described in the
comments).
I also switched the if conditional following this check to an else if, to
ensure that we never call dio_bio_submit twice for the same dio (in
theory, this should not happen, anyway).
I've tested this by running blktrace and verifying that a 64KB I/O was
submitted as a single I/O. I also ran the patched kernel through
xfstests' aio tests using xfs, ext4 (with 1k and 4k block sizes) and btrfs
and verified that there were no regressions as compared to an unpatched
kernel.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Josef Bacik <jbacik@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Chris Mason <chris.mason@oracle.com> Cc: <stable@kernel.org> [2.6.35.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 9 Sep 2010 23:37:29 +0000 (16:37 -0700)]
rtc-bfin: fix state restoration when resuming
Much (but not all) of the RTC state is kept in the RTC peripheral which
has its own power domain. Periodically (1 HZ), that state is synced from
one power domain to the other (peripheral->core). When we are resuming,
we need to wait for the sync to occur so that we don't get a mismatch of
reading undefined state in the rest of the driver.
Further, once the externally maintained bits have been synced back into
the core, we then need to restore the bits maintained in the core. In our
particular case, that is just the write completion interrupt bit.
If we don't do any of this, working with the RTC causes ~5 second delays
from time to time after waking up due to the write completion interrupt
never firing.
Reported-by: Michael Dean <mdean@aeronix.com> Reported-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 9 Sep 2010 23:37:27 +0000 (16:37 -0700)]
rtc-bfin: fix inverted logic in suspend path
The int_clear helper takes a bitmask of interrupts to keep, not to
disable. When suspending without wakeup enabled, we want to disable
all interrupts, so use 0 (keep none) instead of -1 (keep all).
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Vrabel [Thu, 9 Sep 2010 23:37:24 +0000 (16:37 -0700)]
mmc: avoid getting CID on SDIO-only cards
The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).
When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: David Vrabel <david.vrabel@csr.com> Acked-by: Michal Mirolaw <mirq-linux@rere.qmqm.pl> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
ARM: Update mach-types
ARM: Partially revert "Auto calculate ZRELADDR and provide option for exceptions"
ARM: Ensure PTE modifications via dma_alloc_coherent are visible
ARM: 6359/1: ep93xx: move clock initialization earlier
Revert "[ARM] pxa: remove now unnecessary dma_needs_bounce()"
ARM: 6352/1: perf: fix event validation
ARM: 6344/1: Mark CPU_32v6K as depended on CPU_V7
ARM: 6343/1: wire up fanotify and prlimit64 syscalls on ARM
ARM: 6330/1: perf: reword comments relating to perf_event_do_pending
ARM: pxa168fb: fix section mismatch
ARM: pxa: Make id const in pwm_probe()
ARM: pxa: fix CI_HSYNC and CI_VSYNC MFP defines for pxa300
ARM: pxa: remove __init from cpufreq_driver->init()
ARM: imx: set cache line size to 64 bytes for i.MX5
mx5/clock: fix clear bit fields issue in _clk_ccgr_disable function
mxc/tzic: add base address when accessing TZIC registers
ARM: mach-shmobile: ap4evb: fix write protect for SDHI1
ARM: mach-shmobile: ap4evb: modify FSI2 ID
ARM: mach-shmobile: do not enable the PLLC2 clock on init
ARM: mach-shmobile: Clock framework comment fix
...
Russell King [Thu, 9 Sep 2010 21:39:41 +0000 (22:39 +0100)]
ARM: Partially revert "Auto calculate ZRELADDR and provide option for exceptions"
Partially revert e69edc7, which introduced automatic zreladdr
support. The change in the way the manual definition is defined
seems to be error and conflict prone. Go back to the original way
we were handling this for the time being, while keeping the automatic
zreladdr facility.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suresh Siddha [Mon, 23 Aug 2010 20:42:51 +0000 (13:42 -0700)]
sched: Move sched_avg_update() to update_cpu_load()
Currently sched_avg_update() (which updates rt_avg stats in the rq)
is getting called from scale_rt_power() (in the load balance context)
which doesn't take rq->lock.
Fix it by moving the sched_avg_update() to more appropriate
update_cpu_load() where the CFS load gets updated as well.
Tejun Heo [Fri, 27 Aug 2010 09:09:15 +0000 (11:09 +0200)]
ahci: fix hang on failed softreset
ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue. The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout. If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.
Jean Delvare [Mon, 30 Aug 2010 15:37:05 +0000 (17:37 +0200)]
pata_artop: Fix device ID parity check
x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AT91: SAM9G45 - add a separate clock entry for every single TC block
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().
Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk] Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 9 Sep 2010 17:58:23 +0000 (19:58 +0200)]
AT91: clock: peripheral clocks can have other parent than mck
While registering clock allow to set parent clock other
than mck. It is useful for clocks than can be seen as
child clock of a peripheral.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Andrew Victor <linux@maxim.org.za>
Zachary Amsden [Fri, 20 Aug 2010 08:07:27 +0000 (22:07 -1000)]
KVM: x86: Perform hardware_enable in CPU_STARTING callback
The CPU_STARTING callback was added upstream with the intention
of being used for KVM, specifically for the hardware enablement
that must be done before we can run in hardware virt. It had
bugs on the x86_64 architecture at the time, where it was called
after CPU_ONLINE. The arches have since merged and the bug is
gone.
It might be noted other features should probably start making
use of this callback; microcode updates in particular which
might be fixing important erratums would be best applied before
beginning to run user tasks.
Jonathan Corbet [Wed, 8 Sep 2010 22:54:54 +0000 (16:54 -0600)]
lglock: make lg_lock_global() actually lock globally
lg_lock_global() currently only acquires spinlocks for online CPUs, but
it's meant to lock all possible CPUs. Lglock-protected resources may be
associated with removed CPUs - and, indeed, that could happen with the
per-superblock open files lists.
At Nick's suggestion, change for_each_online_cpu() to
for_each_possible_cpu() to protect accesses to those resources.
Cc: Al Viro <viro@ZenIV.linux.org.uk> Acked-by: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix hang with modified FIN handling on A0 cards
RDMA/nes: Change state to closing after FIN
RDMA/nes: Fix double CLOSE event indication crash
RDMA/nes: Write correct register write to set TX pause param
RDMA/cxgb3: Don't exceed the max HW CQ depth
Merge branch 'fixes' of git://oss.oracle.com/git/tma/linux-2.6
* 'fixes' of git://oss.oracle.com/git/tma/linux-2.6:
ocfs2: Fix orphan add in ocfs2_create_inode_in_orphan
ocfs2: split out ocfs2_prepare_orphan_dir() into locking and prep functions
ocfs2: allow return of new inode block location before allocation of the inode
ocfs2: use ocfs2_alloc_dinode_update_counts() instead of open coding
ocfs2: split out inode alloc code from ocfs2_mknod_locked
Ocfs2: Fix a regression bug from mainline commit(6b933c8e6f1a2f3118082c455eef25f9b1ac7b45).
ocfs2: Fix deadlock when allocating page
ocfs2: properly set and use inode group alloc hint
ocfs2: Use the right group in nfs sync check.
ocfs2: Flush drive's caches on fdatasync
ocfs2: make __ocfs2_page_mkwrite handle file end properly.
ocfs2: Fix incorrect checksum validation error
ocfs2: Fix metaecc error messages
Chris Wilson [Wed, 8 Sep 2010 23:02:03 +0000 (00:02 +0100)]
drm/i915: Double check that the wait_request is not pending before warning
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073 Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Eric Dumazet [Wed, 8 Sep 2010 05:08:44 +0000 (05:08 +0000)]
udp: add rehash on connect()
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Cross [Thu, 2 Sep 2010 23:24:07 +0000 (01:24 +0200)]
PM: Prevent waiting forever on asynchronous resume after failing suspend
During suspend, the power.completion is expected to be set when a
device has not yet started suspending. Set it on init to fix a
corner case where a device is resumed when its parent has never
suspended.
Consider three drivers, A, B, and C. The parent of A is C, and C
has async_suspend set. On boot, C->power.completion is initialized
to 0.
During the first suspend:
suspend_devices_and_enter(...)
dpm_resume(...)
device_suspend(A)
device_suspend(B) returns error, aborts suspend
dpm_resume_end(...)
dpm_resume(...)
device_resume(A)
dpm_wait(A->parent == C)
wait_for_completion(C->power.completion)
The wait_for_completion will never complete, because
complete_all(C->power.completion) will only be called from
device_suspend(C) or device_resume(C), neither of which is called
if suspend is aborted before C.
After a successful suspend->resume cycle, where B doesn't abort
suspend, C->power.completion is left in the completed state by the
call to device_resume(C), and the same call path will work if B
aborts suspend.
Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Faisal Latif [Sat, 14 Aug 2010 21:05:04 +0000 (21:05 +0000)]
RDMA/nes: Change state to closing after FIN
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Sat, 14 Aug 2010 21:04:56 +0000 (21:04 +0000)]
RDMA/nes: Fix double CLOSE event indication crash
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Jianzhao Wang [Wed, 8 Sep 2010 21:35:43 +0000 (14:35 -0700)]
net: blackhole route should always be recalculated
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18bf41719c9f0d7ed494d295dd2973b92.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allow trie_firstleaf() to be called either under rcu_read_lock()
protection or with RTNL held. The same annotation is added to
node_parent_rcu() to prevent a similar warning a bit later.
Ben Hutchings [Tue, 7 Sep 2010 04:35:19 +0000 (04:35 +0000)]
niu: Fix kernel buffer overflow for ETHTOOL_GRXCLSRLALL
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mcheck: Avoid duplicate sysfs links/files for thresholding banks
io-mapping: Fix the address space annotations
x86: Fix the address space annotations of iomap_atomic_prot_pfn()
x86, mm: Fix CONFIG_VMSPLIT_1G and 2G_OPT trampoline
x86, hwmon: Fix unsafe smp_processor_id() in thermal_throttle_add_dev
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
gcc-4.6: kernel/*: Fix unused but set warnings
mutex: Fix annotations to include it in kernel-locking docbook
pid: make setpgid() system call use RCU read-side critical section
MAINTAINERS: Add RCU's public git tree
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix lock annotations
fuse: flush background queue on connection close
- Do not create expectation when forwarding the PORT
command to avoid blocking the connection. The problem is that
nf_conntrack_ftp.c:help() tries to create the same expectation later in
POST_ROUTING and drops the packet with "dropping packet" message after
failure in nf_ct_expect_related.
- Change ip_vs_update_conntrack to alter the conntrack
for related connections from real server. If we do not alter the reply in
this direction the next packet from client sent to vport 20 comes as NEW
connection. We alter it but may be some collision happens for both
conntracks and the second conntrack gets destroyed immediately. The
connection stucks too.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch: "gro: fix different skb headrooms" in its part:
"2) allocate a minimal skb for head of frag_list" is buggy. The copied
skb has p->data set at the ip header at the moment, and skb_gro_offset
is the length of ip + tcp headers. So, after the change the length of
mac header is skipped. Later skb_set_mac_header() sets it into the
NET_SKB_PAD area (if it's long enough) and ip header is misaligned at
NET_SKB_PAD + NET_IP_ALIGN offset. There is no reason to assume the
original skb was wrongly allocated, so let's copy it as it was.
Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 8 Sep 2010 15:27:56 +0000 (16:27 +0100)]
ARM: Ensure PTE modifications via dma_alloc_coherent are visible
Dave Hylands reports:
| We've observed a problem with dma_alloc_writecombine when the system
| is under heavy load (heavy bus traffic). We've managed to reduce the
| problem to the following snippet, which is run from a kthread in a
| continuous loop:
|
| void *virtAddr;
| dma_addr_t physAddr;
| unsigned int numBytes = 256;
|
| for (;;) {
| virtAddr = dma_alloc_writecombine(NULL,
| numBytes, &physAddr, GFP_KERNEL);
| if (virtAddr == NULL) {
| printk(KERN_ERR "Running out of memory\n");
| break;
| }
|
| /* access DMA memory allocated */
| tmp = virtAddr;
| *tmp = 0x77;
|
| /* free DMA memory */
| dma_free_writecombine(NULL,
| numBytes, virtAddr, physAddr);
|
| ...sleep here...
| }
|
| By itself, the code will run forever with no issues. However, as we
| increase our bus traffic (typically using DMA) then the *tmp = 0x77
| line will eventually cause a page fault. If we add a small delay (a
| few microseconds) before the *tmp = 0x77, then we don't see a page
| fault, even under heavy load.
A dsb() is required after modifying the PTE entries to ensure that they
will always be visible. Add this dsb().
Reported-by: Dave Hylands <dhylands@gmail.com> Tested-by: Dave Hylands <dhylands@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Masami Hiramatsu [Fri, 27 Aug 2010 11:39:06 +0000 (20:39 +0900)]
tracing/kprobes: Fix handling of argument names
Set "argN" name for each argument automatically if it has no specified name.
Since dynamic trace event(kprobe_events) accepts special characters for its
argument, its format can show those special characters (e.g. '$', '%', '+').
However, perf can't parse those format because of the character (especially
'%') mess up the format. This sets "argX" name for those arguments if user
omitted the argument names.
Masami Hiramatsu [Fri, 27 Aug 2010 11:38:59 +0000 (20:38 +0900)]
perf probe: Fix handling of arguments names
Don't make argument names from raw parameters (means the parameters are written
in kprobe-tracer syntax), because the argument syntax may include special
characters. Just leave it, then kprobe-tracer gives a new name.
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100827113859.22882.75598.stgit@ltc236.sdl.hitachi.co.jp> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masami Hiramatsu [Fri, 27 Aug 2010 11:38:46 +0000 (20:38 +0900)]
tracing/kprobe: Fix a memory leak in error case
Fix a memory leak which happens when a field name conflicts with others. In
error case, free_trace_probe() will free all arguments until nr_args, so this
increments nr_args the begining of the loop instead of the end.
Steven Rostedt [Wed, 8 Sep 2010 15:20:37 +0000 (11:20 -0400)]
tracing: Do not allow llseek to set_ftrace_filter
Reading the file set_ftrace_filter does three things.
1) shows whether or not filters are set for the function tracer
2) shows what functions are set for the function tracer
3) shows what triggers are set on any functions
3 is independent from 1 and 2.
The way this file currently works is that it is a state machine,
and as you read it, it may change state. But this assumption breaks
when you use lseek() on the file. The state machine gets out of sync
and the t_show() may use the wrong pointer and cause a kernel oops.
Luckily, this will only kill the app that does the lseek, but the app
dies while holding a mutex. This prevents anyone else from using the
set_ftrace_filter file (or any other function tracing file for that matter).
A real fix for this is to rewrite the code, but that is too much for
a -rc release or stable. This patch simply disables llseek on the
set_ftrace_filter() file for now, and we can do the proper fix for the
next major release.
Reported-by: Robert Swiecki <swiecki@google.com> Cc: Chris Wright <chrisw@sous-sol.org> Cc: Tavis Ormandy <taviso@google.com> Cc: Eugene Teo <eugene@redhat.com> Cc: vendor-sec@lst.de Cc: <stable@kernel.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Thomas Gleixner [Tue, 7 Sep 2010 12:46:37 +0000 (14:46 +0200)]
semaphore: Add DEFINE_SEMAPHORE
The full cleanup of init_MUTEX[_LOCKED] and DECLARE_MUTEX has not been
done. Some of the users are real semaphores and we should name them as
such instead of confusing everyone with "MUTEX".
Provide the infrastructure to get finally rid of init_MUTEX[_LOCKED]
and DECLARE_MUTEX.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@infradead.org>
LKML-Reference: <20100907125054.795929962@linutronix.de>
ALSA: hda - Fix wrong HP pin detection in snd_hda_parse_pin_def_config()
snd_hda_parse_pin_def_config() has some workaround for re-assigning
some pins declared as headphones to line-outs. This didn't work properly
for some cases because it used memmove() stupidly wrongly.
Commit 7cfe24947 ("ARM: AMBA: Add pclk support to AMBA bus
infrastructure") changed AMBA bus to handle the PCLK automatically.
However, in EP93xx clock initialization is arch_initcall which is done
later than AMBA device identification. This causes
amba_get_enable_pclk() to fail resulting device where UARTs are not
functional.
So change ep93xx_clock_init() to be postcore_initcall.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 5 Sep 2010 11:19:50 +0000 (12:19 +0100)]
Revert "[ARM] pxa: remove now unnecessary dma_needs_bounce()"
This reverts commit 4fa5518, which causes a compilation regression for
IXP4xx platforms.
Reported-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ALSA: seq/oss - Fix double-free at error path of snd_seq_oss_open()
The error handling in snd_seq_oss_open() has several bad codes that
do dereferecing released pointers and double-free of kmalloc'ed data.
The object dp is release in free_devinfo() that is called via
private_free callback. The rest shouldn't touch this object any more.
The patch changes delete_port() to call kfree() in any case, and gets
rid of unnecessary calls of destructors in snd_seq_oss_open().
This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.
The root cause still remains, so we will add some better debugging when
we focus on fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021 Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307 Reported-and-tested-by: Enrico Bandiello <enban@postal.uv.es> Poked-by: Florian Mickler <florian@mickler.org> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Adam Jackson <ajax@redhat.com> Cc: stable@kernel.org
ALSA: hda - Enable PC-beep for EeePC with ALC269 codec
EeePC 1001HAG has a similar problem like other ASUS machine, which doesn't
set the codec SSID properly for indicating the beep capability.
To enable PC-beep again, put this to the whitelist.
ALSA: usb - Release capture substream URBs properly
Due to the wrong "return" in the loop, a capture substream won't be
released at disconnection properly if the device is capture only and has
no playback substream. This caused Oops occasionally at the device
reconnection.
Reported-by: Kim Minhyoung <minhyoung.kim@lge.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Tue, 7 Sep 2010 11:38:49 +0000 (13:38 +0200)]
ALSA: virtuoso: fix setting of Xonar DS line-in/mic-in controls
The Line and Mic inputs cannot be used at the same time, so the driver
has to automatically disable one of them if both are set. However, it
forgot to notify userspace about this change, so the mixer state would
be inconsistent. To fix this, check if the other control gets muted,
and send a notification event in this case.
Clemens Ladisch [Tue, 7 Sep 2010 11:37:10 +0000 (13:37 +0200)]
ALSA: virtuoso: work around missing reset in the Xonar DS Windows driver
For the WM8776 chip, this driver uses a different sample format and
more features than the Windows driver. When rebooting from Linux into
Windows, the latter driver does not reset the chip but assumes all its
registers have their default settings, so we get garbled sound or, if
the output happened to be muted before rebooting, no sound.
To make that driver happy, hook our driver's cleanup function into the
shutdown notifier and ensure that the chip gets reset.
Mark Fasheh [Fri, 13 Aug 2010 22:15:19 +0000 (15:15 -0700)]
ocfs2: Fix orphan add in ocfs2_create_inode_in_orphan
ocfs2_create_inode_in_orphan() is used by reflink to create the newly
reflinked inode simultaneously in the orphan dir. This allows us to easily
handle partially-reflinked files during recovery cleanup.
We have a problem though - the orphan dir stringifies inode # to determine
a unique name under which the orphan entry dirent can be created. Since
ocfs2_create_inode_in_orphan() needs the space allocated in the orphan dir
before it can allocate the inode, we currently call into the orphan code:
/*
* We give the orphan dir the root blkno to fake an orphan name,
* and allocate enough space for our insertion.
*/
status = ocfs2_prepare_orphan_dir(osb, &orphan_dir,
osb->root_blkno,
orphan_name, &orphan_insert);
Using osb->root_blkno might work fine on unindexed directories, but the
orphan dir can have an index. When it has that index, the above code fails
to allocate the proper index entry. Later, when we try to remove the file
from the orphan dir (using the actual inode #), the reflink operation will
fail.
To fix this, I created a function ocfs2_alloc_orphaned_file() which uses the
newly split out orphan and inode alloc code to figure out what the inode
block number will be (once allocated) and then prepare the orphan dir from
that data.
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Tao Ma <tao.ma@oracle.com>
projects / linux.git / log