Boris Brezillon [Mon, 25 Feb 2019 08:28:54 +0000 (09:28 +0100)]
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
Boris Brezillon [Mon, 25 Feb 2019 08:28:25 +0000 (09:28 +0100)]
Merge tag 'spi-nor/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
SPI NOR Changes
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Frieder Schrempf [Mon, 18 Feb 2019 12:04:43 +0000 (12:04 +0000)]
mtd: spi-nor: Add support for MX25V8035F
This adds support for the Macronix MX25V8035F, a 8Mb SPI NOR chip.
It is used on i.MX6UL/ULL SoMs by Kontron Electronics GmbH (N631x).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Frieder Schrempf [Mon, 18 Feb 2019 12:04:43 +0000 (12:04 +0000)]
mtd: spi-nor: Add support for EN25Q80A
This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
It is used on i.MX6 boards by Kontron Electronics GmbH
(N60xx, N61xx).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Vignesh R [Tue, 12 Feb 2019 08:38:09 +0000 (14:08 +0530)]
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Vignesh R [Tue, 12 Feb 2019 08:38:08 +0000 (14:08 +0530)]
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Ahmet Celenk [Tue, 12 Feb 2019 06:24:42 +0000 (09:24 +0300)]
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: Ahmet Celenk <ahmet.celenk@procenne.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.
This patch allows all the 8 bytes to be written.
Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Masahiro Yamada [Tue, 15 Jan 2019 08:11:34 +0000 (17:11 +0900)]
mtd: rawnand: denali_dt: remove single anonymous clock support
Commit 6f1fe97bec34 ("mtd: rawnand: denali_dt: add more clocks based
on IP datasheet") introduced a more correct binding that requires
three named clocks.
Now that all upstream DT files migrated over to it, remove the single
anonymous clock support.
Wen Yang [Thu, 7 Feb 2019 14:01:32 +0000 (14:01 +0000)]
mtd: rawnand: mtk: fix possible object reference leak
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device") Signed-off-by: Wen Yang <yellowriver2010@hotmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wen Yang [Thu, 7 Feb 2019 14:01:23 +0000 (14:01 +0000)]
mtd: rawnand: jz4780: fix possible object reference leak
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: ae02ab00aa3c ("mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs") Signed-off-by: Wen Yang <yellowriver2010@hotmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wen Yang [Thu, 7 Feb 2019 03:50:55 +0000 (03:50 +0000)]
mtd: rawnand: atmel: fix possible object reference leak
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Wen Yang <yellowriver2010@hotmail.com> Suggested-by: Boris Brezillon <bbrezillon@kernel.org> Reviewed-by: Boris Brezillon <bbrezillon@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Tudor Ambarus <tudor.ambarus@microchip.com> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: linux-mtd@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Linus Walleij [Sat, 26 Jan 2019 13:10:55 +0000 (14:10 +0100)]
mtd: rawnand: fsmc: Reset NAND timings on resume()
When we go through a suspend/resume cycle the NAND
timings and other settings may have been lost so reset
the chip to bring it up in a known working state.
The FSMC only supports single CS chips so we only need
to call nand_reset(chip, 0).
This code was added by commit 26d266e10e5e ("mtd: nand: denali: fix
raw and oob accessors for syndrome page layout"), but I do not see
sensible reason.
The IRQ flags are correctly reset by denali_cmd_ctrl(), so this code
is unneeded.
Masahiro Yamada [Mon, 21 Jan 2019 13:05:34 +0000 (22:05 +0900)]
mtd: rawnand: check return code of nand_reset() and nand_readid_op()
nand_scan_ident() iterates over maxchips to find as many homogeneous
chips as possible.
Since commit 2d472aba15ff ("mtd: nand: document the NAND
controller/NAND chip DT representation"), new drivers should pass in
the exact number of CS lines instead of possible max, but old
platforms may still rely on nand_scan_ident() to detect the actual
number of connected CS lines.
In that case, this loop bails out when manufacturer or device ID
unmatches. The reason of unmatch is most likely no chip is connected
to that CS line. If so, nand_reset() should already have failed,
and the following nand_readid_op() is pointless.
Before ->exec_op hook was introduced, drivers had no way to tell
the failure of NAND_CMD_RESET to the framework because the legacy
->cmdfunc() has void return type. Now drivers implementing ->exec_op
hook can return the error code. You can save nand_readid_op() by
checking the return value of nand_reset(). The return value of
nand_readid_op() should be checked as well. If it fails, probably
id[0] and id[1] are undefined values.
Just for consistency, it should be sensible to check the return
code in nand_do_write_oob() as well.
Masahiro Yamada [Mon, 21 Jan 2019 06:32:07 +0000 (15:32 +0900)]
mtd: rawnand: remove ->legacy.erase and single_erase()
Now that the last user of this hook, denali.c, stopped using it,
we can remove the erase hook from nand_legacy.
I squashed single_erase() because only the difference between
single_erase() and nand_erase_op() is the number of bit shifts.
The status/ret conversion in nand_erase_nand() is unneeded since
commit eb94555e9e97 ("mtd: nand: use usual return values for the
->erase() hook"). Cleaned it up now.
Masahiro Yamada [Mon, 21 Jan 2019 04:52:06 +0000 (13:52 +0900)]
mtd: rawnand: denali: remove ->erase hook
Commit f9ebd1bb4103 ("mtd: rawnand: Deprecate ->erase()") discouraged
the use of this hook, so I am happy to follow the suggestion.
Although the Denali IP provides a special MAP10 command for erasing,
using it would not buy us much. The Denali IP actually works with the
generic erasing by single_erase() + ->cmdfunc hook (nand_command_lp)
+ ->cmd_ctrl hook (denali_cmd_ctrl).
This method is also deprecated, but denali_erase() can go away
irrespective of ->exec_op conversion.
mtd: rawnand: Annotate implicit fall through in nand_scan_tail
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_base.c:5556:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5575:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5613:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
mtd: rawnand: Annotate implicit fall through in nand_command/nand_command_lp
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_legacy.c:332:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_legacy.c:483:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Tue, 20 Nov 2018 10:57:20 +0000 (11:57 +0100)]
mtd: rawnand: Simplify the locking
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Tue, 20 Nov 2018 10:57:19 +0000 (11:57 +0100)]
mtd: rawnand: Stop using chip->state in drivers
We are about to simplify the locking in the rawnand framework, and part
of this simplication is about getting rid of chip->state, so let's
first patch drivers that check the state.
All of them do that to get a timeout value based on the operation that
is being executed. Since a timeout is, by definition, something that
is here to prevent hanging on an event that might never happen,
picking the maximum timeout value no matter the operation should be
harmless.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Tue, 20 Nov 2018 10:57:18 +0000 (11:57 +0100)]
mtd: rawnand: omap2: Use nand_controller_init()
Stop initializing omap_gpmc_controller fields are declaration time and
replace that by a call to nand_controller_init(). Since the same object
might be shared by several NAND chips and the NAND controller driver
expects a ->probe() per-chip, we need to keep track of the
omap_gpmc_controller state (whether it's already been initialized or
not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Tue, 20 Nov 2018 10:57:17 +0000 (11:57 +0100)]
mtd: rawnand: tmio: Do not abuse nand_controller->wq
nand_controller->wq has never been meant to be used by NAND controller
drivers. This waitqueue is used by the framework to serialize accesses
to a NAND controller, and messing up with its state is a really bad
idea.
Declare a completion object in tmio_nand and use it to wait for RB
transitions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd: rawnand: marvell: use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Boris Brezillon [Thu, 20 Dec 2018 14:10:47 +0000 (15:10 +0100)]
mtd: rawnand: sunxi: Handle the tREA > tRC / 2 case
In non-EDO, tREA should be less than tRP to guarantee that the
controller does not sample the IO lines too early. Unfortunately, the
sunxi NAND controller does not allow us to have different values for
tRP and tREH (tRP = tREH = tRW / 2).
We have 2 options to overcome this limitation:
1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint
2/ Use EDO mode (only works if timings->tRLOH > 0)
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch is based on FMC2 command sequencer.
The purpose of the command sequencer is to facilitate the programming
and the reading of NAND flash pages with the ECC and to free the CPU
of sequencing tasks.
It requires one DMA channel for write and two DMA channels for read
operations.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4 and
MT29F8G16ABACAH4
Sergei Shtylyov [Wed, 16 Jan 2019 17:53:25 +0000 (20:53 +0300)]
mtd: spi-nor: refine Spansion S25FL512S ID
Spansion S25FL512S ID is erroneously using 5-byte JEDEC ID, while the chip
family ID is stored in the 6th byte. Due to using only 5-byte ID, it's also
covering S25FS512S and now that we have added 6-byte ID for that chip, we
can convert S25FL512S to using a proper 6-byte ID as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Sergei Shtylyov [Wed, 16 Jan 2019 17:51:56 +0000 (20:51 +0300)]
mtd: spi-nor: add Spansion S25FS512S ID
Spansion S25FS512S flash is currently misdetected as S25FL512S since the
latter uses 5-byte JEDEC ID, while the 6th ID byte (family ID) is different
on those chips. Add the 6-byte S25FS512S ID before S25FL512S ID in order
not to break the existing S25FS512S users.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
mtd: spi-nor: add octal read flag for flash mt35xu512aba
Add octal read flag for flash mt35xu512aba.
This flash, mt35xu512aba, is only complaint to SFDP JESD216B and does
not seem to support newer JESD216C standard that provides auto
detection of Octal mode capabilities and opcodes. Therefore, this
capability is manually added using new SPI_NOR_OCTAL_READ flag.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
mtd: spi-nor: add opcodes for octal Read/Write commands
- Add opcodes for octal I/O commands
* Read : 1-1-8 and 1-8-8 protocol
* Write : 1-1-8 and 1-8-8 protocol
* opcodes for 4-byte address mode command
- Entry of macros in _convert_3to4_xxx function
- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
commands. This flag is required for flashes which didn't provides
support for auto detection of Octal mode capabilities i.e. not
seems to support newer JESD216C standard.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Boris Brezillon [Thu, 20 Dec 2018 14:13:20 +0000 (15:13 +0100)]
mtd: Implement mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
mtd_{read,write}_oob() already take care of checking the params and
calling ->_{read,write}() or ->_{read,write}_oob() based on the
request and the operations supported by the MTD device.
No need to duplicate the logic, we can simply implement
mtd_{read,write}() as wrappers around mtd_{read,write}_oob().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tudor Ambarus [Tue, 15 Jan 2019 16:57:52 +0000 (16:57 +0000)]
MAINTAINERS: add myself as SPI NOR co-maintainer
I have been reviewing and contributing to the SPI NOR subsystem
for the last few months and I'm willing to continue doing so.
Volunteer as a maintainer for the SPI NOR part of the MTD subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
mtd: cfi: cmdset_0001: Use struct_size() in kmalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Since we can set module parameters also when a driver is built in,
it makes no sense to protect module parameter with #ifdef MODULE.
Now the mtdram sizes can also set when the module is not a loadable
module.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Linus Torvalds [Mon, 7 Jan 2019 00:33:10 +0000 (16:33 -0800)]
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Linus Torvalds [Mon, 7 Jan 2019 00:30:14 +0000 (16:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
Linus Torvalds [Sun, 6 Jan 2019 01:50:59 +0000 (17:50 -0800)]
Change mincore() to count "mapped" pages rather than "cached" pages
The semantics of what "in core" means for the mincore() system call are
somewhat unclear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache" rather than "page is mapped in the mapping".
The problem with that traditional semantic is that it exposes a lot of
system cache state that it really probably shouldn't, and that users
shouldn't really even care about.
So let's try to avoid that information leak by simply changing the
semantics to be that mincore() counts actual mapped pages, not pages
that might be cheaply mapped if they were faulted (note the "might be"
part of the old semantics: being in the cache doesn't actually guarantee
that you can access them without IO anyway, since things like network
filesystems may have to revalidate the cache before use).
In many ways the old semantics were somewhat insane even aside from the
information leak issue. From the very beginning (and that beginning is
a long time ago: 2.3.52 was released in March 2000, I think), the code
had a comment saying
Later we can get more picky about what "in core" means precisely.
and this is that "later". Admittedly it is much later than is really
comfortable.
NOTE! This is a real semantic change, and it is for example known to
change the output of "fincore", since that program literally does a
mmmap without populating it, and then doing "mincore()" on that mapping
that doesn't actually have any pages in it.
I'm hoping that nobody actually has any workflow that cares, and the
info leak is real.
We may have to do something different if it turns out that people have
valid reasons to want the old semantics, and if we can limit the
information leak sanely.
Cc: Kevin Easton <kevin@guarana.org> Cc: Jiri Kosina <jikos@kernel.org> Cc: Masatake YAMATO <yamato@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 19:15:04 +0000 (11:15 -0800)]
Fix 'acccess_ok()' on alpha and SH
Commit 594cc251fdd0 ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net> Cc: Matt Turner <mattst88@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 20:19:23 +0000 (12:19 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Fix a number of ext4 bugs"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix special inode number checks in __ext4_iget()
ext4: track writeback errors using the generic tracking infrastructure
ext4: use ext4_write_inode() when fsyncing w/o a journal
ext4: avoid kernel warning when writing the superblock to a dead device
ext4: fix a potential fiemap/page fault deadlock w/ inline_data
ext4: make sure enough credits are reserved for dioread_nolock writes
Linus Torvalds [Sun, 6 Jan 2019 19:47:26 +0000 (11:47 -0800)]
Merge tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions introduced in this cycles:
- fix dma-debug tracking for the map_page / map_single
consolidatation
- properly stub out DMA mapping symbols for !HAS_DMA builds to avoid
link failures
- fix AMD Gart direct mappings
- setup the dma address for no kernel mappings using the remap
allocator"
* tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING for remapped allocations
x86/amd_gart: fix unmapping of non-GART mappings
dma-mapping: remove a few unused exports
dma-mapping: properly stub out the DMA API for !CONFIG_HAS_DMA
dma-mapping: remove dmam_{declare,release}_coherent_memory
dma-mapping: implement dmam_alloc_coherent using dmam_alloc_attrs
dma-mapping: implement dma_map_single_attrs using dma_map_page_attrs
Linus Torvalds [Sun, 6 Jan 2019 19:40:06 +0000 (11:40 -0800)]
Merge tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- Changes for EC_MKBP_EVENT_SENSOR_FIFO handling.
- Also, maintainership changes. Olofj out, Enric balletbo in.
* tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
MAINTAINERS: add maintainers for ChromeOS EC sub-drivers
MAINTAINERS: platform/chrome: Add Enric as a maintainer
MAINTAINERS: platform/chrome: remove myself as maintainer
platform/chrome: don't report EC_MKBP_EVENT_SENSOR_FIFO as wakeup
platform/chrome: straighten out cros_ec_get_{next,host}_event() error codes
Eric Biggers [Sun, 6 Jan 2019 13:36:21 +0000 (08:36 -0500)]
fscrypt: add Adiantum support
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit 059c2a4d8e16 ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sun, 6 Jan 2019 02:35:02 +0000 (18:35 -0800)]
Merge tag 'docs-5.0-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"
* tag 'docs-5.0-fixes' of git://git.lwn.net/linux:
doc: filesystems: fix bad references to nonexistent ext4.rst file
Documentation/admin-guide: update URL of LKML information link
Docs/kernel-api.rst: Remove blk-tag.c reference
Linus Torvalds [Sun, 6 Jan 2019 02:33:21 +0000 (18:33 -0800)]
Merge tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"Remove an explicit dependency in Kconfig which is implied by another
dependency"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: Remove depends on HAS_DMA in case of platform dependency
Linus Torvalds [Sun, 6 Jan 2019 02:29:13 +0000 (18:29 -0800)]
Merge tag 'for-linus-20190104' of git://git.kernel.dk/linux-block
Pull block updates and fixes from Jens Axboe:
- Pulled in MD changes that Shaohua had queued up for 4.21.
Unfortunately we lost Shaohua late 2018, I'm sending these in on his
behalf.
- In conjunction with the above, I added a CREDITS entry for Shaoua.
- sunvdc queue restart fix (Ming)
* tag 'for-linus-20190104' of git://git.kernel.dk/linux-block:
Add CREDITS entry for Shaohua Li
block: sunvdc: don't run hw queue synchronously from irq context
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
Linus Torvalds [Sun, 6 Jan 2019 02:25:19 +0000 (18:25 -0800)]
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Linus Torvalds [Sun, 6 Jan 2019 02:20:51 +0000 (18:20 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Over the break a few defects were found, so this is a -rc style pull
request of various small things that have been posted.
- An attempt to shorten RCU grace period driven delays showed crashes
during heavier testing, and has been entirely reverted
- A missed merge/rebase error between the advise_mr and ib_device_ops
series
- Some small static analysis driven fixes from Julia and Aditya
- Missed ability to create a XRC_INI in the devx verbs interop
series"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
infiniband/qedr: Potential null ptr dereference of qp
infiniband: bnxt_re: qplib: Check the return value of send_message
IB/ipoib: drop useless LIST_HEAD
IB/core: Add advise_mr to the list of known ops
Revert "IB/mlx5: Fix long EEH recover time with NVMe offloads"
IB/mlx5: Allow XRC INI usage via verbs in DEVX context
Linus Torvalds [Sun, 6 Jan 2019 02:15:37 +0000 (18:15 -0800)]
Merge tag 'fbdev-v4.21' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"This time the pull request is really small.
The most notable changes are fixing fbcon to not cause crash on
unregister_framebuffer() operation when there is more than one
framebuffer, adding config option to center the bootup logo and making
FB_BACKLIGHT config option tristate (which in turn uncovered incorrect
FB_BACKLIGHT usage by DRM's nouveau driver).
Summary:
- fix fbcon to not cause crash on unregister_framebuffer() when there
is more than one framebuffer (Noralf Trønnes)
- improve support for small rotated displays (Peter Rosin)
- fix probe failure handling in udlfb driver (Dan Carpenter)
- add config option to center the bootup logo (Peter Rosin)
- make FB_BACKLIGHT config option tristate (Rob Clark)
- remove superfluous HAS_DMA dependency for goldfishfb driver (Geert
Uytterhoeven)
- misc fixes (Alexey Khoroshilov, YueHaibing, Colin Ian King, Lubomir
Rintel)
- misc cleanups (Yangtao Li, Wen Yang)
also there is DRM's nouveau driver fix for wrong FB_BACKLIGHT config
option usage (FB_BACKLIGHT is for internal fbdev subsystem use only)"
* tag 'fbdev-v4.21' of git://github.com/bzolnier/linux:
drm/nouveau: fix incorrect FB_BACKLIGHT usage in Kconfig
fbdev: fbcon: Fix unregister crash when more than one framebuffer
fbdev: Remove depends on HAS_DMA in case of platform dependency
pxa168fb: trivial typo fix
fbdev: fsl-diu: remove redundant null check on cmap
fbdev: omap2: omapfb: convert to DEFINE_SHOW_ATTRIBUTE
fbdev: uvesafb: fix spelling mistake "memoery" -> "memory"
fbdev: fbmem: add config option to center the bootup logo
fbdev: fbmem: make fb_show_logo_line return the end instead of the height
video: fbdev: pxafb: Fix "WARNING: invalid free of devm_ allocated data"
fbdev: fbmem: behave better with small rotated displays and many CPUs
video: clps711x-fb: release disp device node in probe()
fbdev: make FB_BACKLIGHT a tristate
udlfb: fix some inconsistent NULL checking
Linus Torvalds [Sun, 6 Jan 2019 02:13:35 +0000 (18:13 -0800)]
Merge branch 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has only driver updates for you this time.
Mostly new IDs/DT compatibles, also SPDX conversions, small cleanups.
STM32F7 got FastMode+ and PM support, Axxia some reliabilty
improvements"
* 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: Add Actions Semiconductor Owl family S700 I2C support
dt-bindings: i2c: Add S700 support for Actions Semi Soc's
i2c: ismt: Add support for Intel Cedar Fork
i2c: tegra: Switch to SPDX identifier
i2c: tegra: Add missing kerneldoc for some fields
i2c: tegra: Cleanup kerneldoc comments
i2c: axxia: support sequence command mode
dt-bindings: i2c: rcar: Add r8a774c0 support
dt-bindings: i2c: sh_mobile: Add r8a774c0 support
i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)
i2c: i2c-cros-ec-tunnel: Switch to SPDX identifier.
i2c: powermac: Use of_node_name_eq for node name comparisons
i2c-axxia: check for error conditions first
i2c-axxia: dedicated function to set client addr
dt-bindings: i2c: Use correct vendor prefix for Atmel
i2c: tegra: replace spin_lock_irqsave with spin_lock in ISR
eeprom: at24: add support for 24c2048
dt-bindings: eeprom: at24: add "atmel,24c2048" compatible string
i2c: i2c-stm32f7: add PM Runtime support
i2c: sh_mobile: add support for r8a77990 (R-Car E3)
...
Linus Torvalds [Sun, 6 Jan 2019 01:53:40 +0000 (17:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
Masahiro Yamada [Thu, 3 Jan 2019 01:10:39 +0000 (10:10 +0900)]
arch: remove redundant UAPI generic-y defines
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:38 +0000 (10:10 +0900)]
kbuild: generate asm-generic wrappers if mandatory headers are missing
Some time ago, Sam pointed out a certain degree of overwrap between
generic-y and mandatory-y. (https://lkml.org/lkml/2017/7/10/121)
I tweaked the meaning of mandatory-y a little bit; now it defines the
minimum set of ASM headers that all architectures must have.
If arch does not have specific implementation of a mandatory header,
Kbuild will let it fallback to the asm-generic one by automatically
generating a wrapper. This will allow to drop lots of redundant
generic-y defines.
Previously, "mandatory" was used in the context of UAPI, but I guess
this can be extended to kernel space ASM headers.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Mon, 31 Dec 2018 08:24:09 +0000 (17:24 +0900)]
kbuild: change filechk to surround the given command with { }
filechk_* rules often consist of multiple 'echo' lines. They must be
surrounded with { } or ( ) to work correctly. Otherwise, only the
string from the last 'echo' would be written into the target.
Let's take care of that in the 'filechk' in scripts/Kbuild.include
to clean up filechk_* rules.
Masahiro Yamada [Mon, 31 Dec 2018 04:09:00 +0000 (13:09 +0900)]
kbuild: clean up rule_dtc_dt_yaml
Commit 3a2429e1faf4 ("kbuild: change if_changed_rule for multi-line
recipe") and commit 4f0e3a57d6eb ("kbuild: Add support for DT binding
schema checks") came in via different sub-systems.
Mathias Krause [Sun, 30 Dec 2018 12:36:00 +0000 (13:36 +0100)]
kallsyms: lower alignment on ARM
As mentioned in the info pages of gas, the '.align' pseudo op's
interpretation of the alignment value is architecture specific.
It might either be a byte value or taken to the power of two.
On ARM it's actually the latter which leads to unnecessary large
alignments of 16 bytes for 32 bit builds or 256 bytes for 64 bit
builds.
Fix this by switching to '.balign' instead which is consistent
across all architectures.
projects / linux.git / log