Ping Cheng [Tue, 27 Jan 2015 21:29:36 +0000 (13:29 -0800)]
HID: wacom: consolidate input capability settings for pen and touch
After PAD moved to its own interface, there were duplicated statements in
wacom_setup_pentouch_input_capabilities. Merge them together to reduce future
maintenance effort.
Ping Cheng [Wed, 28 Jan 2015 17:42:59 +0000 (09:42 -0800)]
HID: wacom: make sure touch arbitration is applied consistently
stylus_in_proximity is used to make sure no touch event is sent while pen is in
proximity. touch_down is used to make sure a touch up event is sent when pen
comes into proximity while touch is down.
Two touch routines didn't store touch_down. One touch routine forgot to check
stylus_in_proximity before sending touch events. This patch fixes those issues.
Jim Keir [Fri, 23 Jan 2015 17:21:12 +0000 (17:21 +0000)]
HID: pidff: Fix initialisation forMicrosoft Sidewinder FF Pro 2
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Jason Gerecke [Thu, 22 Jan 2015 23:53:28 +0000 (15:53 -0800)]
HID: wacom: Report ABS_MISC event for Cintiq Companion Hybrid
It appears that the Cintiq Companion Hybrid does not send an ABS_MISC event to
userspace when any of its ExpressKeys are pressed. This is not strictly
necessary now that the pad exists on its own device, but should be fixed for
consistency's sake.
Traditionally both the stylus and pad shared the same device node, and
xf86-input-wacom would use ABS_MISC for disambiguation. Not sending this causes
the Hybrid to behave incorrectly with xf86-input-wacom beginning with its
8f44f3 commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Michal Marek [Wed, 21 Jan 2015 13:07:10 +0000 (14:07 +0100)]
HID: Use Kbuild idiom in Makefiles
Use <driver>-$(CONFIG_FOO) syntax to build multipart objects with
optional parts, since all the config options are bool. Also, delete the
obvious comments in the usbhid Makefile.
Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kristian Evensen [Tue, 20 Jan 2015 16:55:03 +0000 (17:55 +0100)]
HID: do not bind to Microchip Pick16F1454
The Microchip Pick16F1454 is exported as a HID device and is used by for
example the Yepkit YKUSH three-port switchable USB hub. However, it is not an
actual HID-device. On the Yepkit, it is used to power up/down the ports on the
hub. The HID driver should ignore this device.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ping Cheng [Fri, 9 Jan 2015 19:05:13 +0000 (11:05 -0800)]
HID: wacom: peport In Range event according to the spec
Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.
While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Ping Cheng [Fri, 9 Jan 2015 19:04:50 +0000 (11:04 -0800)]
HID: wacom: process invalid Cintiq and Intuos data in wacom_intuos_inout()
Users may use unsupported tools on Cintiq or Intuos. When invalid tools or data
are detected, they should be ignored. That is, no event from those tools should
be reported.
Consolidating that code in wacom_intuos_inout simplifies the logic and make it
easier for future code change.
Andrew Duggan [Thu, 8 Jan 2015 22:51:35 +0000 (14:51 -0800)]
HID: rmi: Add support for the touchpad in the Razer Blade 14 laptop
Have hid-rmi handle all of the Razer Blade HID devices that are part of the
composite USB device. This will allow hid-rmi to operate the touchpad in rmi
mode while passing events from the other devices to hid-input.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andrew Duggan [Thu, 8 Jan 2015 22:51:34 +0000 (14:51 -0800)]
HID: rmi: Support touchpads with external buttons
The external buttons on HID touchpads are connected as pass through devices and
button events are not reported in the rmi registers. As a result on these
devices we need to allow the HID generic desktop button events to be processed
by hid-input. Unfortunately, there is no way to query the touchpad to determine
that it has pass through buttons so the RMI_DEVICE_HAS_PHYS_BUTTONS should be
set manually when adding the device to rmi_id[].
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dan Carpenter [Fri, 9 Jan 2015 12:32:31 +0000 (15:32 +0300)]
HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
This is a static checker fix. We write some binary settings to the
sysfs file. One of the settings is the "->startup_profile". There
isn't any checking to make sure it fits into the
pyra->profile_settings[] array in the profile_activated() function.
I added a check to pyra_sysfs_write_settings() in both places because
I wasn't positive that the other callers were correct.
Cc: <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: logitech-hidpp: store the name of the device in struct hidpp
If a disconnect occurs while getting the actual name of the device
(which can take several HID transactions), the name of the device will
be the hid name, provided by the Unifying Receiver.
This means that in some cases, the user space will see a different
name that what it usually sees when there is no disconnect.
We should store the name of the device in the struct hidpp. That way,
if a disconnect occurs while we are accessing the name,
hidpp_connect_event() can fail, and the input node is not created.
The input node will be created only if we have a connection which
lasts long enough to retrieve all the requested information:
name, protocol, and specific configuration.
Reviewed-by: Peter Wu <peter@lekensteyn.nl> Tested-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Tue, 6 Jan 2015 21:34:19 +0000 (22:34 +0100)]
HID: fixup the conflicting keyboard mappings quirk
The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion
on conflicting mappings") needs to properly check for VARIABLE reports
as well (ARRAY reports should be ignored), otherwise legitimate keyboards
might break.
Cc: <stable@vger.kernel.org> Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings") Reported-by: Fredrik Hallenberg <megahallon@gmail.com> Reported-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(Note that the number of keys is the same, but key '5' is moved down and
the shape of key '4' is changed. Keys '1' to '3' are exactly the same.)
The keys 1-4 report the same scan-code in HID in both layouts, even though
the keysym they produce is usually different depending on the XKB-keymap
used by user-space.
However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout
and 0x32 for the lower layout, as defined by the HID spec. This is highly
confusing as the linux-input API uses a single keycode for both.
So far, this was never a problem as there never has been a keyboard with
both of those keys present at the same time. It would have to look
something like this:
HID can represent such a keyboard, but the linux-input API cannot.
Furthermore, any user-space mapping would be confused by this and,
luckily, no-one ever produced such hardware.
Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to
the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys
is present on a hardware, this works just fine.
Lets introduce hardware-vendors into this:
------------------------------------------
Unfortunately, it seems way to expensive to produce a different device for
American and European layouts. Therefore, hardware-vendors put both keys,
(0x31 and 0x32) on the same keyboard, but only one of them is hooked up
to the physical button, the other one is 'dead'.
This means, they can use the same hardware, with a different button-layout
and automatically produce the correct HID events for American *and*
European layouts. This is unproblematic for normal keyboards, as the
'dead' key will never report any KEY-DOWN events. But RollOver keyboards
send the whole matrix on each key-event, allowing n-key roll-over mode.
This means, we get a 0x31 and 0x32 event on each key-press. One of them
will always be 0, the other reports the real state. As we map both to the
same keycode, we will get spurious key-events, even though the real
key-state never changed.
The easiest way would be to blacklist 'dead' keys and never handle those.
We could simply read the 'country' tag of USB devices and blacklist either
key according to the layout. But... hardware vendors... want the same
device for all countries and thus many of them set 'country' to 0 for all
devices. Meh..
So we have to deal with this properly. As we cannot know which of the keys
is 'dead', we either need a heuristic and track those keys, or we simply
make use of our value-tracking for HID fields. We simply ignore HID events
for absolute data if the data didn't change. As HID tracks events on the
HID level, we haven't done the keycode translation, yet. Therefore, the
'dead' key is tracked independently of the real key, therefore, any events
on it will be ignored.
This patch simply discards any HID events for absolute data if it didn't
change compared to the last report. We need to ignore relative and
buffered-byte reports for obvious reasons. But those cannot be affected by
this bug, so we're fine.
Preferably, we'd do this filtering on the HID-core level. But this might
break a lot of custom drivers, if they do not follow the HID specs.
Therefore, we do this late in hid-input just before we inject it into the
input layer (which does the exact same filtering, but on the keycode
level).
If this turns out to break some devices, we might have to limit filtering
to EV_KEY events. But lets try to do the Right Thing first, and properly
filter any absolute data that didn't change.
This patch is tagged for 'stable' as it fixes a lot of n-key RollOver
hardware. We might wanna wait with backporting for a while, before we know
it doesn't break anything else, though.
Cc: <stable@vger.kernel.org> Reported-by: Adam Goode <adam@spicenitz.org> Reported-by: Fredrik Hallenberg <megahallon@gmail.com> Tested-by: Fredrik Hallenberg <megahallon@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: wacom: add support of the Pen of the Bamboo Pad
Bamboo Pads are using the generic processing but their report descriptors
differ from the ISDv* line. The pen fields are marked with the .physical
as Digitizer_Pen, which makes also sense.
Add this field to the checks and enable for free Bamboo Pads.
Reported-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Reviewed-by: Jason Gerecke <killertofu@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: Add a new id 0x501a for Genius MousePen i608X
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Jiri Kosina [Mon, 22 Dec 2014 13:58:13 +0000 (14:58 +0100)]
HID: betop: add drivers/hid/hid-betopff.c
Commit fc38a8a66e ("HID: add BETOP game controller force feedback support")
is missing the actual addition of drivers/hid/hid-betopff.c due to my
mistake (I forgot to add the file after fixing conflicts).
Fixes: fc38a8a66e1b ("HID: add BETOP game controller force feedback support") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andrew Duggan [Fri, 19 Dec 2014 22:45:41 +0000 (14:45 -0800)]
HID: rmi: Support non rmi devices by passing events to hid-input
Allowing hid-rmi to bind to non rmi devices allows us to support composite USB
devices which contain several HID devices one of which is a HID touchpad.
Since all of the devices have the same VID and PID we can add the device
to the hid_have_special_driver list and have hid-rmi handle all of the devices.
Then hid-rmi's probe can look for the rmi specific HID report IDs and decide if
it should handle the device as a rmi device or simply report that the events
needs additional processing.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a return to avoid a fall-through. Introduced in commit 57ac86cf52e903d9e3e0f12b34c814cce6b65550 ("HID: logitech-hidpp: add
support of the first Logitech Wireless Touchpad").
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Tue, 16 Dec 2014 00:50:14 +0000 (01:50 +0100)]
HID: logitech-hidpp: detect HID++ 2.0 errors too
Devices speaking HID++ 2.0 report a different error code (0xff). Detect
these errors too to avoid 5 second delays when the device reports an
error. Caught by... well, a bug in the QEMU emulation of this receiver.
Renamed fap to rap for HID++ 1.0 errors because it is more logical,
it has no functional difference.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Daniel Nicoletti [Wed, 17 Dec 2014 13:53:54 +0000 (11:53 -0200)]
HID: Allow HID_BATTERY_STRENGTH to be enabled
Allows for HID_BATTERY_STRENGTH config be enabled without the need for HID
module to be built-in, prior to this HID and POWER_SUPPLY had to be equal, and
now we only select POWER_SUPPLY and depend on the HID module.
Signed-off-by: Daniel Nicoletti <dantti12@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Mika Westerberg [Fri, 12 Dec 2014 12:01:49 +0000 (14:01 +0200)]
HID: i2c-hid: Do not free buffers in i2c_hid_stop()
When a hid driver that uses i2c-hid as transport is unloaded, the hid core
will call i2c_hid_stop() which releases all the buffers associated with the
device. This includes also the command buffer.
Now, when the i2c-hid driver itself is unloaded it tries to power down the
device by sending it PWR_SLEEP command. Since the command buffer is already
released we get following crash:
Andrew Duggan [Fri, 12 Dec 2014 18:17:26 +0000 (10:17 -0800)]
HID: rmi: Scan the report descriptor to determine if the device is suitable for the hid-rmi driver
On composite HID devices there may be multiple HID devices on separate
interfaces, but hid-rmi should only bind to the touchpad. The previous version
simply checked that the interface protocol was set to mouse. Unfortuately, it
is not always the case that the touchpad has the mouse interface protocol set.
This patch takes a different approach and scans the report descriptor looking
for the Generic Desktop Pointer usage and the Vendor Specific Top Level
Collection needed by the hid-rmi driver to interface with the device.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: logitech-hidpp: bail out if wtp_connect fails
If wtp_connect() fails, that means most of the time that the device has
been disconnected. Subsequent attempts to contact the device will fail
too, so it's simpler to bail out earlier.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Reviewed-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Karl Relton [Tue, 16 Dec 2014 15:37:22 +0000 (15:37 +0000)]
HID: add battery quirk for USB_DEVICE_ID_APPLE_ALU_WIRELESS_2011_ISO keyboard
Apple bluetooth wireless keyboard (sold in UK) has always reported zero
for battery strength no matter what condition the batteries are actually
in. With this patch applied (applying same quirk as other Apple
keyboards), the battery strength is now correctly reported.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jamie Lentin [Tue, 16 Dec 2014 21:26:46 +0000 (21:26 +0000)]
HID: lenovo: Use native middle-button mode for compact keyboards
By default the middle button is in a compatibility mode, and generates
standard wheel events when dragging with the middle trackpoint button.
Unfortunately this is buggy:
* The middle button comes up before starting wheel events, causing a middle
click on whatever the mouse cursor was sitting on
* The USB keyboard always generates the "native" horizontal wheel event,
regardless of mode.
Instead, enable the "native" mode the Windows driver uses, and add support
for the custom events this generates. This fixes the USB keyboard wheel
events, and the middle-click up event comes after the wheel events.
Peter Wu [Tue, 16 Dec 2014 23:23:51 +0000 (00:23 +0100)]
HID: logitech-hidpp: separate HID++ from WTP processing
Previously wtp_raw_event would be called through
hidpp_raw_hidpp_event (for the touchpad report) and hidpp_raw_event
(for the mouse report).
This patch removes one calling surface, making a clearer distinction
between "generic HID++ processing" (matching internal reports) and
device-specific event processing.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Tue, 16 Dec 2014 15:55:22 +0000 (16:55 +0100)]
HID: logitech-hidpp: check WTP report length
Malicious USB devices can send bogus reports smaller than the expected
buffer size. Ensure that the length for WTP reports is valid to avoid
reading out of bounds.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Fri, 12 Dec 2014 18:26:47 +0000 (10:26 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
Linus Torvalds [Fri, 12 Dec 2014 17:57:22 +0000 (09:57 -0800)]
Merge tag 'upstream-3.19-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Artem Bityutskiy:
"This includes the following UBI/UBIFS changes:
- UBI debug messages now include the UBI device number. This change
is responsible for the big diffstat since it touched every
debugging print statement.
- An Xattr bug-fix which fixes SELinux support
- Several error path fixes in UBI/UBIFS"
* tag 'upstream-3.19-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix invalid vfree()
UBI: Fix double free after do_sync_erase()
UBIFS: fix a couple bugs in UBIFS xattr length calculation
UBI: vtbl: Use ubi_eba_atomic_leb_change()
UBI: Extend UBI layer debug/messaging capabilities
UBIFS: fix budget leak in error path
Linus Torvalds [Fri, 12 Dec 2014 17:48:17 +0000 (09:48 -0800)]
Merge tag 'xfs-for-linus-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs update from Dave Chinner:
"There's relatively little change in this update; it is mainly bug
fixes, cleanups and more of the on-going libxfs restructuring and
on-disk format header consolidation work.
Details:
- more on-disk format header consolidation
- move some structures shared with userspace to libxfs
- new per-mount workqueue to fix for deadlocks between nested loop
mounted filesystems
- various bug fixes for ENOSPC, stats, quota off and preallocation
- a bunch of compiler warning fixes for set-but-unused variables
- various code cleanups"
* tag 'xfs-for-linus-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (24 commits)
xfs: split metadata and log buffer completion to separate workqueues
xfs: fix set-but-unused warnings
xfs: move type conversion functions to xfs_dir.h
xfs: move ftype conversion functions to libxfs
xfs: lobotomise xfs_trans_read_buf_map()
xfs: active inodes stat is broken
xfs: cleanup xfs_bmse_merge returns
xfs: cleanup xfs_bmse_shift_one goto mess
xfs: fix premature enospc on inode allocation
xfs: overflow in xfs_iomap_eof_align_last_fsb
xfs: fix simple_return.cocci warning in xfs_bmse_shift_one
xfs: fix simple_return.cocci warning in xfs_file_readdir
libxfs: fix simple_return.cocci warnings
xfs: remove unnecessary null checks
xfs: merge xfs_inum.h into xfs_format.h
xfs: move most of xfs_sb.h to xfs_format.h
xfs: merge xfs_ag.h into xfs_format.h
xfs: move acl structures to xfs_format.h
xfs: merge xfs_dinode.h into xfs_format.h
xfs: catch invalid negative blknos in _xfs_buf_find()
...
Linus Torvalds [Fri, 12 Dec 2014 17:28:03 +0000 (09:28 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Lots of bugs fixes, including Zheng and Jan's extent status shrinker
fixes, which should improve CPU utilization and potential soft lockups
under heavy memory pressure, and Eric Whitney's bigalloc fixes"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (26 commits)
ext4: ext4_da_convert_inline_data_to_extent drop locked page after error
ext4: fix suboptimal seek_{data,hole} extents traversial
ext4: ext4_inline_data_fiemap should respect callers argument
ext4: prevent fsreentrance deadlock for inline_data
ext4: forbid journal_async_commit in data=ordered mode
jbd2: remove unnecessary NULL check before iput()
ext4: Remove an unnecessary check for NULL before iput()
ext4: remove unneeded code in ext4_unlink
ext4: don't count external journal blocks as overhead
ext4: remove never taken branch from ext4_ext_shift_path_extents()
ext4: create nojournal_checksum mount option
ext4: update comments regarding ext4_delete_inode()
ext4: cleanup GFP flags inside resize path
ext4: introduce aging to extent status tree
ext4: cleanup flag definitions for extent status tree
ext4: limit number of scanned extents in status tree shrinker
ext4: move handling of list of shrinkable inodes into extent status code
ext4: change LRU to round-robin in extent status tree shrinker
ext4: cache extent hole in extent status tree for ext4_da_map_blocks()
ext4: fix block reservation for bigalloc filesystems
...
Andrew Duggan [Mon, 8 Dec 2014 23:02:00 +0000 (15:02 -0800)]
HID: rmi: The address of query8 must be calculated based on which query registers are present
If a touchpad does not report relative data then query 6 will not be present and the address
of query 8 will be one less. This patches calculates the location of query 8 instead of
hardcoding the offset.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andrew Duggan [Mon, 8 Dec 2014 23:01:59 +0000 (15:01 -0800)]
HID: rmi: Check for additional ACM registers appended to F11 data report
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
Gwendal Grignou [Fri, 12 Dec 2014 00:02:45 +0000 (16:02 -0800)]
HID: i2c-hid: prevent buffer overflow in early IRQ
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Linus Torvalds [Fri, 12 Dec 2014 02:57:19 +0000 (18:57 -0800)]
Merge branch 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup update from Tejun Heo:
"cpuset got simplified a bit. cgroup core got a fix on unified
hierarchy and grew some effective css related interfaces which will be
used for blkio support for writeback IO traffic which is currently
being worked on"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: implement cgroup_get_e_css()
cgroup: add cgroup_subsys->css_e_css_changed()
cgroup: add cgroup_subsys->css_released()
cgroup: fix the async css offline wait logic in cgroup_subtree_control_write()
cgroup: restructure child_subsys_mask handling in cgroup_subtree_control_write()
cgroup: separate out cgroup_calc_child_subsys_mask() from cgroup_refresh_child_subsys_mask()
cpuset: lock vs unlock typo
cpuset: simplify cpuset_node_allowed API
cpuset: convert callback_mutex to a spinlock
Linus Torvalds [Fri, 12 Dec 2014 02:52:37 +0000 (18:52 -0800)]
Merge branch 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata changes from Tejun Heo:
"The only interesting piece is the support for shingled drives. The
changes in libata layer are minimal. All it does is identifying the
new class of device and report upwards accordingly"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Remove FIXME comment in atapi_request_sense()
sata_rcar: Document deprecated "renesas,rcar-sata"
sata_rcar: Add clocks to sata_rcar bindings
ahci_sunxi: Make AHCI_HFLAG_NO_PMP flag configurable with a module option
libata-scsi: Update SATL for ZAC drives
libata: Implement ATA_DEV_ZAC
libsas: use ata_dev_classify()
Linus Torvalds [Fri, 12 Dec 2014 02:48:45 +0000 (18:48 -0800)]
Merge branch 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue update from Tejun Heo:
"Work items which may be involved in memory reclaim path may be
executed by the rescuer under memory pressure. When a rescuer gets
activated, it processes whatever are on the pending list and then goes
back to sleep until the manager kicks it again which involves 100ms
delay.
This is problematic for self-requeueing work items or the ones running
on ordered workqueues as there always is only one work item on the
pending list when the rescuer kicks in. The execution of that work
item produces more to execute but the rescuer won't see them until
after the said 100ms has passed, so such workqueues would only execute
one work item every 100ms under prolonged memory pressure, which BTW
may be being prolonged due to the slow execution.
Neil wrote up a patch which fixes this issue by keeping the rescuer
working as long as the target workqueue is busy but doesn't have
enough workers"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: allow rescuer thread to do more work.
workqueue: invert the order between pool->lock and wq_mayday_lock
workqueue: cosmetic update in rescuer_thread()
Linus Torvalds [Fri, 12 Dec 2014 02:36:26 +0000 (18:36 -0800)]
Merge branch 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu updates from Tejun Heo:
"Nothing interesting. A patch to convert the remaining __get_cpu_var()
users, another to fix non-critical off-by-one in an assertion and a
cosmetic conversion to lockless_dereference() in percpu-ref.
The back-merge from mainline is to receive lockless_dereference()"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Replace smp_read_barrier_depends() with lockless_dereference()
percpu: Convert remaining __get_cpu_var uses in 3.18-rcX
percpu: off by one in BUG_ON()
Linus Torvalds [Fri, 12 Dec 2014 02:15:33 +0000 (18:15 -0800)]
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
Linus Torvalds [Fri, 12 Dec 2014 01:56:37 +0000 (17:56 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Linus Torvalds [Fri, 12 Dec 2014 01:48:14 +0000 (17:48 -0800)]
Merge tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
Linus Torvalds [Fri, 12 Dec 2014 01:30:55 +0000 (17:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"The most notable change for this pull request is the ftrace rework
from Heiko. It brings a small performance improvement and the ground
work to support a new gcc option to replace the mcount blocks with a
single nop.
Two new s390 specific system calls are added to emulate user space
mmio for PCI, an artifact of the how PCI memory is accessed.
Two patches for the memory management with changes to common code.
For KVM mm_forbids_zeropage is added which disables the empty zero
page for an mm that is used by a KVM process. And an optimization,
pmdp_get_and_clear_full is added analog to ptep_get_and_clear_full.
Some micro optimization for the cmpxchg and the spinlock code.
And as usual bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (46 commits)
s390/cputime: fix 31-bit compile
s390/scm_block: make the number of reqs per HW req configurable
s390/scm_block: handle multiple requests in one HW request
s390/scm_block: allocate aidaw pages only when necessary
s390/scm_block: use mempool to manage aidaw requests
s390/eadm: change timeout value
s390/mm: fix memory leak of ptlock in pmd_free_tlb
s390: use local symbol names in entry[64].S
s390/ptrace: always include vector registers in core files
s390/simd: clear vector register pointer on fork/clone
s390: translate cputime magic constants to macros
s390/idle: convert open coded idle time seqcount
s390/idle: add missing irq off lockdep annotation
s390/debug: avoid function call for debug_sprintf_*
s390/kprobes: fix instruction copy for out of line execution
s390: remove diag 44 calls from cpu_relax()
s390/dasd: retry partition detection
s390/dasd: fix list corruption for sleep_on requests
s390/dasd: fix infinite term I/O loop
s390/dasd: remove unused code
...
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
Peter Wu [Thu, 11 Dec 2014 12:51:20 +0000 (13:51 +0100)]
HID: logitech-hidpp: disable io in probe error path
Balance a hid_device_io_start() call with hid_device_io_stop() in the
error path. This avoids processing of HID reports when the probe fails
which possibly leads to invalid memory access in hid_device_probe() as
report_enum->report_id_hash might already be freed via
hid_close_report().
hid_set_drvdata() is called before wtp_allocate, be consistent and clear
drvdata too on the error path of wtp_allocate.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Thu, 11 Dec 2014 12:51:18 +0000 (13:51 +0100)]
HID: logitech-hidpp: check name retrieval return code
hidpp_devicenametype_get_device_name() may return a negative value on
protocol errors (for example, when the device is powered off).
Explicitly check this condition to avoid a long-running loop.
(0 cannot be returned as __name_length - index > 0, but check for it
anyway as it would otherwise result in an infinite loop.)
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Thu, 11 Dec 2014 12:51:17 +0000 (13:51 +0100)]
HID: logitech-hidpp: do not return the name length
We do not make any use of the actual name length get through
hidpp_get_device_name(). Original patch by Benjamin Tissoires, this
patch also replaces a (now) unnecessary goto by return NULL.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke [Thu, 11 Dec 2014 00:26:04 +0000 (16:26 -0800)]
HID: wacom: Report input events for each finger on generic devices
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Thu, 11 Dec 2014 21:20:50 +0000 (13:20 -0800)]
Merge tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
Linus Torvalds [Thu, 11 Dec 2014 21:06:58 +0000 (13:06 -0800)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
Linus Torvalds [Thu, 11 Dec 2014 20:46:32 +0000 (12:46 -0800)]
Merge tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- support for mx6sl and mx6sx
- OMAP HDMI audio rewrite to make it finally work
- OMAP video PLL work to prepare for new DRA7xx SoCs
- simplefb DT related improvements
* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
video: smscufx: Deletion of unnecessary checks before the function call "vfree"
video: udlfb: Deletion of unnecessary checks before the function call "vfree"
video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
video: fbdev: arkfb: suppress build warning
video: fbdev: s3fb: suppress build warning
video: fbdev: vt8623fb: suppress build warning
OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
OMAPDSS: Remove all references to obsolete HDMI audio callbacks
ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
...
Linus Torvalds [Thu, 11 Dec 2014 20:09:37 +0000 (12:09 -0800)]
Merge branch 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox framework updates from Jassi Brar.
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
Mailbox: Add support for Platform Communication Channel
mailbox/omap: adapt to the new mailbox framework
mailbox: add tx_prepare client callback
mailbox: Don't unnecessarily re-arm the polling timer
Linus Torvalds [Thu, 11 Dec 2014 20:03:34 +0000 (12:03 -0800)]
Merge tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
Intel Quark X1000 and Samsung Exynos 7 controllers"
* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
spi/s3c64xx: Remove redundant runtime PM management
spi: fsl-spi: remove unused variable assignment
spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
spi: core: Do not mangle error code from kthread_run()
spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
spi: fsl-(e)spi: migrate to generic master queueing
spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
spi: cadence: Fix 3-to-8 mux mode
spi: cadence: Init HW after reading devicetree attributes
spi: meson: Select REGMAP_MMIO
spi: s3c64xx: add support for exynos7 SPI controller
spi: spi-pxa2xx: SPI support for Intel Quark X1000
spi: meson: meson_spifc_setup_speed() can be static
spi: spi-pxa2xx: Add helpers for regiseters' accessing
spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
spi: atmel: introduce probe deferring
spi: atmel: remove compat for non DT board when requesting dma chan
spi: meson: Add support for Amlogic Meson SPIFC
spi: meson: Add device tree bindings documentation for SPIFC
spi: core: Add spi_transfer_is_last() helper
...
Linus Torvalds [Thu, 11 Dec 2014 19:58:50 +0000 (11:58 -0800)]
Merge tag 'edac/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull edac updates from Mauro Carvalho Chehab:
- Broadwell-DE support on sb-edac driver
- Some fixes at sb-edac driver
* tag 'edac/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: Fix typo computing number of banks
sb_edac: Add support for Broadwell-DE processor
sb_edac: Fix discovery of top-of-low-memory for Haswell
sb_edac: Fix erroneous bytes->gigabytes conversion
sb_edac: Fix off-by-one error in number of channels
Marcelo Leitner [Thu, 11 Dec 2014 12:02:22 +0000 (10:02 -0200)]
Fix race condition between vxlan_sock_add and vxlan_sock_release
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue") Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 11 Dec 2014 19:49:23 +0000 (11:49 -0800)]
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
David S. Miller [Thu, 11 Dec 2014 19:47:40 +0000 (14:47 -0500)]
Merge branch 'mlx4-next'
Or Gerlitz says:
====================
mlx4 driver update
This series from Matan, Jenny, Dotan and myself is mostly about adding
support to a new performance optimized flow steering mode (patches 4-10).
The 1st two patches are small fixes (one for VXLAN and one for SRIOV),
and the third patch is a fix to avoid hard-lockup situation when many
(hunderds) processes holding user-space QPs/CQs get events.
Matan and Or.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:58:00 +0000 (10:58 +0200)]
net/mlx4: Add support for A0 steering
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:57:59 +0000 (10:57 +0200)]
net/mlx4: Refactor QUERY_PORT
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:57:58 +0000 (10:57 +0200)]
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:57:57 +0000 (10:57 +0200)]
net/mlx4: Add A0 hybrid steering
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:57:56 +0000 (10:57 +0200)]
net/mlx4: Add mlx4_bitmap zone allocator
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dotan Barak [Thu, 11 Dec 2014 08:57:55 +0000 (10:57 +0200)]
net/mlx4: Add a check if there are too many reserved QPs
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Thu, 11 Dec 2014 08:57:53 +0000 (10:57 +0200)]
net/mlx4_core: Use tasklet for user-space CQ completion events
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 11 Dec 2014 08:57:52 +0000 (10:57 +0200)]
net/mlx4_core: Mask out host side virtualization features for guests
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 11 Dec 2014 08:57:51 +0000 (10:57 +0200)]
net/mlx4_en: Set csum level for encapsulated packets
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48a5 ('net/mlx4_en: Extend usage of napi_gro_frags') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 11 Dec 2014 19:39:03 +0000 (11:39 -0800)]
Merge tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
be2net: Export tunnel offloads only when a VxLAN tunnel is created
The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.
Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Thu, 11 Dec 2014 06:08:41 +0000 (14:08 +0800)]
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 11 Dec 2014 18:43:14 +0000 (10:43 -0800)]
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
Linus Torvalds [Thu, 11 Dec 2014 05:17:00 +0000 (21:17 -0800)]
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Linus Torvalds [Thu, 11 Dec 2014 04:58:52 +0000 (20:58 -0800)]
Merge tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Here are the PCI changes intended for v3.19. I don't think there's
anything very exciting here, but there was a lot of MSI-related stuff
coming via Thomas.
Details:
NUMA
- Allow numa_node override via sysfs (Prarit Bhargava)
Resource management
- Restore detection of read-only BARs (Myron Stowe)
- Shrink decoding-disabled window while sizing BARs (Myron Stowe)
- Add informational printk for invalid BARs (Myron Stowe)
- Remove fixed parameter in pci_iov_resource_bar() (Myron Stowe)
MSI
- Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits (Yijing Wang)
- Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()" (Yijing Wang)
- s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq() (Yijing Wang)
Virtualization
- xen: Process failure for pcifront_(re)scan_root() (Chen Gang)
- Make FLR and AF FLR reset warning messages different (Gavin Shan)
Generic host bridge driver
- Allocate config space windows after limiting bus number range (Lorenzo Pieralisi)
- Convert to DT resource parsing API (Lorenzo Pieralisi)
* tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (28 commits)
PCI: Remove fixed parameter in pci_iov_resource_bar()
PCI: Add informational printk for invalid BARs
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
PCI: spear: Remove unnecessary OOM message
PCI: mvebu: Add a blank line after declarations
PCI: designware: Add a blank line after declarations
PCI: exynos: Remove unnecessary return statement
PCI: imx6: Use tabs for indentation
PCI: keystone: Remove unnecessary OOM message
PCI: Remove unused and broken to_hotplug_slot()
PCI: Make FLR and AF FLR reset warning messages different
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
PCI: layerscape: Add Freescale Layerscape PCIe driver
PCI: Simplify if-return sequences
PCI: Delete unnecessary NULL pointer checks
PCI: Shrink decoding-disabled window while sizing BARs
...
Linus Torvalds [Thu, 11 Dec 2014 04:40:51 +0000 (20:40 -0800)]
Merge tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest changes from Steven Rostedt:
"The following ktest updates were done:
- Fix handling the make kernelrelease change
- Fix make_min_config that was broken by new bisect_config changes
- Allow tests to undefine default options (not just being able to
override them)
- Print name of test (if defined) to start of test output"
* tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Add back "tail -1" to kernelrelease make
ktest: Add name to running title
ktest: Allow tests to undefine default options
ktest: Fix make_min_config to handle new assign_configs call
ktest: Use make -s kernelrelease
David S. Miller [Thu, 11 Dec 2014 04:37:06 +0000 (23:37 -0500)]
Merge branch 'fec-next'
Fugang Duan says:
====================
net: fec: driver code clean and bug fix
The patch serial include code clean and bug fix:
Patch#1: avoid dummy operation during suspend/resume test.
Patch#2: bug fix for i.MX6SX SOC that clean all interrupt events during MAC initial process.
Patch#3: before phy device link status is up, only enable MDIO bus interrupt.
V2:
- Modify the comment form from David's suggestion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nimrod Andy [Thu, 11 Dec 2014 01:20:32 +0000 (09:20 +0800)]
net: fec: clear all interrupt events to support i.MX6SX
For i.MX6SX FEC controller, there have interrupt mask and event
field extension. To support all SOCs FEC, we clear all interrupt
events during MAVC initial process.
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nimrod Andy [Thu, 11 Dec 2014 01:20:31 +0000 (09:20 +0800)]
net: fec: reset fep link status in suspend function
On some i.MX6 serial boards, phy power and refrence clock are supplied
or controlled by SOC. When do suspend/resume test, the power and clock
are disabled, so phy device link down.
For current driver, fep->link is still up status, which cause extra operation
like below code. To avoid the dumy operation, we set fep->link to down when
phy device is real down.
...
if (fep->link) {
napi_disable(&fep->napi);
netif_tx_lock_bh(ndev);
fec_stop(ndev);
netif_tx_unlock_bh(ndev);
napi_enable(&fep->napi);
fep->link = phy_dev->link;
status_change = 1;
}
...
Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log