mac80211 sets max amsdu to min supported ht vs vht but TLC only works
with one mode so we can set to the exact mode used (vht/ht)
and enable larger amsdu sizes for vht.
Johannes Berg [Wed, 30 Jan 2019 10:09:22 +0000 (11:09 +0100)]
iwlwifi: pcie: switch to correct RBD/CD layout for 22560
The layout of the RBD (receive buffer descriptor) isn't quite right,
the hardware ended up being implemented differently. Switch to the
correct RBD layout. While at it, remove the now useless extra defines.
Also, switch the CD (completion descriptor) to the right format, which
is basically just a code cleanup because the only field we really used
(rbid) is still in the same place. We may need fragmentation later if
we ever want to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: mvm: use dump worker during restart instead of sync dump
In restart flow, the driver requests HW restart from mac80211
and then mac80211 uses a worker to do the restart flow. In that flow a
sync dump is performed. Instead, schedule the dump worker before
requesting HW restart from mac80211. This approach simplifies the
restart flow.
Also, it is neeeded in order to differentiate between the handling of SW
and HW errors in a future commit.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Shaul Triebitz [Sun, 3 Feb 2019 08:59:08 +0000 (10:59 +0200)]
iwlwifi: mvm: be more forgiving if num of channels is too big
If number of channels in the driver is greater than
number of scan channels given by firmware TLV, do not
fail scan config, but adjust to firmware's number of channels.
This is helpful for supporting in driver new channels before
it being supported by firmware scan.
Sara Sharon [Mon, 17 Dec 2018 12:27:51 +0000 (14:27 +0200)]
iwlwifi: mvm: track changes in beacon count during channel switch
There are some buggy APs that keeps changing the count while forcing
us to block TX. This eventually results in queue hang, assert, and
disconnection. Detect such APs and disconnect gracefully in advance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Mon, 17 Dec 2018 12:01:31 +0000 (14:01 +0200)]
iwlwifi: mvm: disconnect in case of bad channel switch parameters
In case we receive channel switch announcement with immediate
quiet and unknown switching time, we will switch when FW identifies
AP left channel. However, if AP remains on channel, we will
eventually get TX queue hang. Init a work to disconnect if
switch doesn't occur within 1500 milliseconds. Do it also
for a too long channel switch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Mon, 26 Nov 2018 10:00:04 +0000 (12:00 +0200)]
iwlwifi: mvm: track CSA beacons
Send to FW modify command for every beacon we receive during channel
switch. FW will track the count, and make sure the event is scheduled
in time even if AP changed count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Wed, 2 Jan 2019 09:31:05 +0000 (10:31 +0100)]
iwlwifi: mvm: report all NO_DATA events to mac80211
Report all NO_DATA events to mac80211 so they get captured
in radiotap for usage in sniffer scenarios; map the info
type to a reasonable radiotap type for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
wil6210: check null pointer in _wil_cfg80211_merge_extra_ies
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maya Erez [Fri, 22 Feb 2019 14:21:04 +0000 (16:21 +0200)]
wil6210: ignore HALP ICR if already handled
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dedy Lansky [Fri, 22 Feb 2019 14:21:03 +0000 (16:21 +0200)]
wil6210: fix invalid sta statistics update
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ahmad Masri [Fri, 22 Feb 2019 14:21:01 +0000 (16:21 +0200)]
wil6210: support up to 20 stations in AP mode
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dedy Lansky [Fri, 22 Feb 2019 14:21:00 +0000 (16:21 +0200)]
wil6210: add option to drop Tx packets when Tx ring is full
In AP mode with multiple clients, driver stops net queue
(netif_tx_stop_queue) upon first ring (serving specific client)
becoming full. This can have negative effect on transmission to
other clients which may still have room in their corresponding rings.
Implement new policy in which stop/wake net queue are not used. In
case there is no room in the ring for a transmitted packet, drop the
packet.
New policy can be helpful to debug performance issues, to guarantee
maximum utilization of net queues.
New policy is disabled by default and can be enabled by debugfs:
echo 1 > drop_if_ring_full
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surabhi Vishnoi [Tue, 26 Feb 2019 09:53:16 +0000 (15:23 +0530)]
ath10k: Fill rx duration for each peer in fw_stats for WCN3990
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Surabhi Vishnoi [Tue, 26 Feb 2019 09:27:58 +0000 (14:57 +0530)]
ath10k: Fix the wrong calculation ht_idx and idx of rate table for tx_stats
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Surabhi Vishnoi [Tue, 26 Feb 2019 09:27:57 +0000 (14:57 +0530)]
ath10k: Fix the wrong updation of SGI in tx_stats debugfs
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surabhi Vishnoi [Tue, 26 Feb 2019 09:27:56 +0000 (14:57 +0530)]
ath10k: Fix the wrong updation of BW in tx_stats debugfs entry
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Wed, 27 Feb 2019 02:23:47 +0000 (02:23 +0000)]
rtlwifi: rtl8192se: Remove set but not used variable 'seg_ptr'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127ac0 ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Wed, 27 Feb 2019 02:23:34 +0000 (02:23 +0000)]
rtlwifi: rtl8723ae: Remove set but not used variable 'bt_retry_cnt'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Wed, 27 Feb 2019 02:23:21 +0000 (02:23 +0000)]
rtlwifi: rtl8723be: Remove set but not used variable 'b_last_is_cur_rdlstate'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Yang [Fri, 22 Feb 2019 07:15:40 +0000 (15:15 +0800)]
mt76: fix a leaked reference by adding a missing of_node_put
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Felix Fietkau <nbd@nbd.name> Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mediatek@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Thu, 21 Feb 2019 19:31:14 +0000 (13:31 -0600)]
rtlwifi: rtl8192cu: Fix problems with blank lines
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Thu, 21 Feb 2019 19:31:12 +0000 (13:31 -0600)]
rtlwifi: Fix all blank line irregularities in main code files
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Thu, 21 Feb 2019 12:35:49 +0000 (12:35 +0000)]
rsi: fix missing null pointer check from a failed ieee80211_probereq_get call
The call to ieee80211_probereq_get can return NULL if a skb allocation
fails, so add a null pointer check and free an earlier skb on the error
exit return path.
Fixes: 7fdcb8e12660 ("rsi: add support for hardware scan offload") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 21 Feb 2019 10:33:25 +0000 (11:33 +0100)]
brcmfmac: print firmware reported general status errors
Firmware may report general errors using a special message type. Add
basic support for it by simply decoding & printing an error number.
A sample situation in which firmware reports a buf error:
CONSOLE: 027084.733 no host response IOCTL buffer available..so fail the request
will now produce a "Firmware reported general error: 9" on the host.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 21 Feb 2019 10:33:24 +0000 (11:33 +0100)]
brcmfmac: fix size of the struct msgbuf_ring_status
This updates host struct to match the in-firmawre definition. It's a
cosmetic change as it only applies to the reserved struct space.
Fixes: c988b78244df ("brcmfmac: print firmware reported ring status errors") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Mon, 25 Feb 2019 03:32:46 +0000 (03:32 +0000)]
ath9k: remove set but not used variable 'acq'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k: Make sure to zero status.tx_time before reporting TX status
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Abhishek Ambure [Tue, 19 Feb 2019 10:01:08 +0000 (15:31 +0530)]
ath10k: update the max num of peers supported for WCN3990
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Surabhi Vishnoi [Fri, 15 Feb 2019 15:19:37 +0000 (20:49 +0530)]
ath10k: Fix length of wmi tlv command for protected mgmt frames
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi" Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alagu Sankar [Mon, 25 Feb 2019 09:46:03 +0000 (11:46 +0200)]
ath10k: don't report unset rssi values to mac80211
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Mon, 25 Feb 2019 09:46:01 +0000 (11:46 +0200)]
ath10k: sdio: reset chip on power_down()
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alagu Sankar [Mon, 25 Feb 2019 09:45:59 +0000 (11:45 +0200)]
ath10k: sdio: disable fwlog prints
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alagu Sankar [Mon, 25 Feb 2019 09:45:57 +0000 (11:45 +0200)]
ath10k: sdio: set hi_acs_flags
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yu Wang [Mon, 25 Feb 2019 09:45:52 +0000 (11:45 +0200)]
ath10k: correct the format of host memory chunks in wmi init command
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Mon, 25 Feb 2019 09:45:50 +0000 (11:45 +0200)]
ath10k: enhance logging for vdev pdev & peer set param
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Abhishek Ambure [Mon, 25 Feb 2019 09:45:48 +0000 (11:45 +0200)]
ath10k: add support for ack rssi value of data tx packets
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Abhishek Ambure [Mon, 25 Feb 2019 09:45:46 +0000 (11:45 +0200)]
ath10k: add support for ack rssi value of management tx packets
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Rakesh Pillai [Mon, 25 Feb 2019 09:45:44 +0000 (11:45 +0200)]
ath10k: fix descriptor size in ce tx completion for WCN3990
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Felix Fietkau [Tue, 6 Nov 2018 12:47:23 +0000 (13:47 +0100)]
mt76: add driver for MT7603E and MT7628/7688
This driver is for a newer generation of 2x2 MediaTek 802.11n chipsets.
MT7603E is a PCIe chip.
MT7628 and MT7688 are MIPS SoC devices with built-in WLAN.
MT7688 is limited to 1x1
This driver fully supports AP, station, mesh, ad-hoc and monitor mode.
Lorenzo Bianconi [Wed, 20 Feb 2019 22:35:18 +0000 (23:35 +0100)]
mt76: usb: simplify mt76u_tx_build_sg routine
Use skb_to_sgvec instad of skb_to_sgvec_nomark in mt76u_tx_build_sg.
Remove nsgs check in mt76u_tx_build_sg since it is already performed
by skb_to_sgvec
Suggested-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Wed, 20 Feb 2019 23:57:19 +0000 (00:57 +0100)]
mt76: usb: fix warning in mt76u_buf_free
Fix following static checker warning in mt76u_buf_free:
drivers/net/wireless/mediatek/mt76/usb.c:372 mt76u_buf_free()
warn: address of 'urb->sg[i]' is non-NULL
There is no need to check sg page pointer since urb->num_sgs
has been already validated in mt76u_fill_rx_sg
Fixes: cb83585e1121 ("mt76: usb: fix possible memory leak in mt76u_buf_free") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76usb: use synchronous msg for mcu command responses
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 25 Feb 2019 17:37:42 +0000 (18:37 +0100)]
mt76: mt76x02: set MT_TXOP_HLDR_TX40M_BLK_EN for mt76x2
It needs to be always enabled for 76x2 and conditionally enabled/disabled
for 76x0. Since mt76x2_mac_stop clears this bit, ensure that it is enabled
in mt76x02_edcca_init
Felix Fietkau [Mon, 25 Feb 2019 16:25:38 +0000 (17:25 +0100)]
mt76: mt76x02: fix ED/CCA enabling/disabling
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx
being blocked. It must only be enabled again after the MAC has been started
again.
In many places this wasn't done properly, so fix this by always clearing
the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after
channel change or calibration is done
Felix Fietkau [Sun, 24 Feb 2019 10:37:18 +0000 (11:37 +0100)]
mt76: mt76x02: fix beacon timer issue
When mt76x0 and mt76x2 beacon code was unified, it changed the order in which
beacon enable and beacon interval are configured.
Configuring beacon enable before beacon interval can in some cases cause
problems with the beacon timer, leading to clients not waking up properly
from powersave mode.
Fix this by changing the order back to interval first, then enable.
Fixes: cc726268e4dce ("mt76: move mt76x02_bss_info_changed in mt76x02-lib module") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name>
Peter Oskolkov [Sun, 24 Feb 2019 02:25:01 +0000 (18:25 -0800)]
net: fix double-free in bpf_lwt_xmit_reroute
dst_output() frees skb when it fails (see, for example,
ip_finish_output2), so it must not be freed in this case.
Fixes: 3bd0b15281af ("bpf: add handling of BPF_LWT_REROUTE to lwt_bpf.c") Signed-off-by: Peter Oskolkov <posk@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When acquiring the GPIO interrupt line for the switch, it is possible
to trigger lockdep splats. These are false positives, the mutex is in
a different IRQ descriptor. But fix it anyway, since it could mask
real locking issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 23 Feb 2019 16:43:57 +0000 (17:43 +0100)]
net: dsa: mv88e6xxx: Release lock while requesting IRQ
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vakul Garg [Sat, 23 Feb 2019 08:42:37 +0000 (08:42 +0000)]
tls: Return type of non-data records retrieved using MSG_PEEK in recvmsg
The patch enables returning 'type' in msghdr for records that are
retrieved with MSG_PEEK in recvmsg. Further it prevents records peeked
from socket from getting clubbed with any other record of different
type when records are subsequently dequeued from strparser.
For each record, we now retain its type in sk_buff's control buffer
cb[]. Inside control buffer, record's full length and offset are already
stored by strparser in 'struct strp_msg'. We store record type after
'struct strp_msg' inside 'struct tls_msg'. For tls1.2, the type is
stored just after record dequeue. For tls1.3, the type is stored after
record has been decrypted.
Inside process_rx_list(), before processing a non-data record, we check
that we must be able to return back the record type to the user
application. If not, the decrypted records in tls context's rx_list is
left there without consuming any data.
Fixes: 692d7b5d1f912 ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ipv4/v6: icmp: small cleanup and update
v2:
- Add cover letter and user proper patch subject-prefix suggested-by Eric Dumazet
This patch series contains some small cleanup and update,
1) use icmp/v6_sk_exit when icmp_sk_init fails instead of open-code
2) use new percpu allocation interface for the ipv6.icmp_sk
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 23 Feb 2019 05:30:47 +0000 (13:30 +0800)]
ila: Fix uninitialised return value in ila_xlat_nl_cmd_flush
This patch fixes an uninitialised return value error in
ila_xlat_nl_cmd_flush.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 6c4128f65857 ("rhashtable: Remove obsolete...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>