Claudiu Beznea [Thu, 7 Feb 2019 09:24:46 +0000 (09:24 +0000)]
pinctrl: at91: add option to use drive strength bits
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength and
at91_pinctrl_mux_ops::get_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Zhou Yanjie [Mon, 28 Jan 2019 15:19:59 +0000 (23:19 +0800)]
Pinctrl: Ingenic: Unify the function name prefix to "ingenic_gpio_".
In the original code, some function names begin with "ingenic_gpio_",
and some with "gpio_ingenic_". For the sake of uniform style,
all of them are changed to the beginning of "ingenic_gpio_".
Zhou Yanjie [Mon, 28 Jan 2019 15:19:58 +0000 (23:19 +0800)]
Pinctrl: Ingenic: Add missing parts for JZ4770 and JZ4780.
Add mmc2 for JZ4770 and JZ4780:
According to the datasheet, both JZ4770 and JZ4780 have mmc2. But this
part of the original code is missing. It is worth noting that JZ4770's
mmc2 supports 8bit mode while JZ4780's does not, so we added the
corresponding code for both models.
Add nemc-wait for JZ4770 and JZ4780:
Both JZ4770 and JZ4780 have a nemc-wait pin. But this part of the
original code is missing.
Add mac for JZ4770:
JZ4770 have a mac. But this part of the original code is missing.
Zhou Yanjie [Mon, 28 Jan 2019 15:19:57 +0000 (23:19 +0800)]
Pinctrl: Ingenic: Fix bugs caused by differences between JZ4770 and JZ4780.
Delete uart4 and i2c3/4 from JZ4770:
According to the datasheet, only JZ4780 have uart4 and i2c3/4. So we
remove it from the JZ4770 code and add a section corresponding the JZ4780.
Fix bugs in i2c0/1:
The pin number was wrong in the original code.
Fix bugs in uart2:
JZ4770 and JZ4780 have different uart2 pins. So the original section JZ4770
has been modified and the corresponding section of JZ4780 has been added.
Fix bugs in mmc0:
JZ4770 and JZ4780 assigned different pins to mmc0's 4~7 data lines. So the
original section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in mmc1:
JZ4770's mmc1 has 8bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in nemc:
JZ4770's nemc has 16bit mode, while JZ4780 doesn't. So the original section
JZ4770 has been modified and the corresponding section of JZ4780 has been
added. And add missing cs2~5 groups for JZ4770 and JZ4780.
Fix bugs in cim:
JZ4770's cim has 12bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.
Fix bugs in lcd:
Both JZ4770 and JZ4780 lcd should be 24bit instead of 32bit.
The main goal of the change is to remove .pin_config_dbg_parse_modify
callback before a driver with its support appears. So far the in-kernel
interface did not attract any users since its introduction 5 years ago.
Originally .pin_config_dbg_parse_modify callback and the associated
'pinconf-config' debugfs file were introduced in commit f07512e615dd
("pinctrl/pinconfig: add debug interface"), a short description of
'pinconf-config' usage for debugging can be expressed this way:
Write to 'pinconf-config' (see pinconf_dbg_config_write() function):
It supposes to update a global (therefore single!) 'pinconf_dbg_conf'
variable with an alternative setting, the arguments should match
an existing pinconf device and some registered pinctrl mapping 'map':
* $map_type is either 'config_pin' or 'config_group', it should match
'map->type' value of PIN_MAP_TYPE_CONFIGS_PIN or
PIN_MAP_TYPE_CONFIGS_GROUP accordingly,
* $device_name should match 'map->dev_name' string value,
* $state_name should match 'map->name' string value,
* $pin_name should match 'map->data.configs.group_or_pin' string value,
If all above has matched, then $config is a new value to be set by calling
pinconfops->pin_config_dbg_parse_modify(pctldev, config, matched_config).
After a successful write into 'pinconf-config' a user can read the file
to get information about that single modified pin configuration.
The fact is .pin_config_dbg_parse_modify callback has never been defined
in 'struct pinconf_ops' of any pinconf driver, thus an actual modification
of a pin or group state on any present pinconf controller does not happen,
and it declares that all related code is no more than dead code.
I discovered the issue while attempting to add .pin_config_dbg_parse_modify
support in some drivers and found that too short 'MAX_NAME_LEN' set by
is practically insufficient to store a regular pinctrl device name,
which are like 'e6060000.pin-controller-sh-pfc' or pin names like
'MX6QDL_PAD_ENET_REF_CLK', thus it is another indicator that the code
is barely usable, insufficiently tested and unprepossessing.
Of course it might be possible to increase MAX_NAME_LEN, and then add
.pin_config_dbg_parse_modify callbacks to the drivers, but the whole
idea of such a limited debug option looks inviable. A more flexible
way to functionally substitute the original approach is to implicitly
or explicitly use pinctrl_select_state() function whenever needed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Laurent Meunier <laurent.meunier@st.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: remove pinctrl/machine.h inclusion from pinctrl/pinconf.h
The change adds explicit inclusion of linux/pinctrl/machine.h header
to the only needed pinctrl-madera-core.c file, and therefore inclusion
of pinctrl/machine.h header from pinctrl/pinconf.h can be removed.
The change is preparatory to a follow-up reversal of commit f07512e615dd
("pinctrl/pinconfig: add debug interface").
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Brian Masney [Sat, 19 Jan 2019 20:42:52 +0000 (15:42 -0500)]
spmi: pmic-arb: revert "disassociate old virq if hwirq mapping already exists"
Now that spmi-gpio is a proper hierarchical IRQ chip, and all in-tree
users of device tree have been updated, we can now drop the hack that
was introduced to disassociate the old Linux virq if a hwirq mapping
already exists. That patch was introduced to not break git bisect for
any existing boards.
Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Brian Masney [Sat, 19 Jan 2019 20:42:51 +0000 (15:42 -0500)]
spmi: pmic-arb: validate type when mapping IRQ
qpnpint_irq_domain_map did not validate the IRQ type and this can cause
IRQs to not work as expected if an unsupported type (such as
IRQ_TYPE_NONE) is passed in. Now that spmi-gpio is a hierarchical IRQ
controller, and all device tree bindings have been updated, add
additional validation to the type field.
Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it. Code was tested on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Brian Masney [Sat, 19 Jan 2019 20:42:44 +0000 (15:42 -0500)]
qcom: spmi-gpio: add support for hierarchical IRQ chip
spmi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the spmi-gpio code to correct this
issue.
Driver was tested using the volume buttons (via gpio-keys) on the LG
Nexus 5 (hammerhead) phone with the following two configurations.
Brian Masney [Sat, 19 Jan 2019 20:42:43 +0000 (15:42 -0500)]
spmi: pmic-arb: disassociate old virq if hwirq mapping already exists
Check to see if the hwirq is already associated with another virq on
this IRQ domain. If so, then disassociate it before associating the
hwirq with the new virq.
This is a temporary hack that is needed in order to not break git
bisect for existing boards. The next patch in this series converts
spmi-gpio to be a hierarchical IRQ chip, then there are several patches
to update all of the device tree files, and finally this patch will be
reverted within the same patch series.
IRQs for spmi-gpio are all initially setup without an IRQ hierarchy
on pmic-arb when mfd/qcom-spmi-pmic.c is probed (via the
devm_of_platform_populate call) due to the interrupts property in
device tree. Once spmi-gpio is converted to be a hierarchical IRQ chip
in the next patch, existing users of gpio[d]_to_irq() will call
pmic_gpio_to_irq(), and that will use the new IRQ chip code in
spmi-gpio that sets up the IRQ in an IRQ hierarchy. The hwirq is now
associated with two Linux virqs and interrupts will not work as
expected. This patch corrects that issue.
Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the two new functions gpiochip_irq_domain_activate and
gpiochip_irq_domain_deactivate that can be used as the activate and
deactivate functions in the struct irq_domain_ops. This is for
situations where only gpiochip_{lock,unlock}_as_irq needs to be called.
SPMI and SSBI GPIO are two users that will initially use these
functions.
Signed-off-by: Brian Masney <masneyb@onstation.org> Suggested-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Brian Masney [Sat, 19 Jan 2019 20:42:41 +0000 (15:42 -0500)]
spmi: pmic-arb: convert to v2 irq interfaces to support hierarchical IRQ chips
Convert the spmi-pmic-arb IRQ code to use the version 2 IRQ interface
in order to support hierarchical IRQ chips. This is necessary so that
spmi-gpio can be setup as a hierarchical IRQ chip with pmic-arb as the
parent. IRQ chips in device tree should be usable from the start without
the consumer having to make an additional call to gpio[d]_to_irq() to
get the proper IRQ on the parent.
The old qpnpint_irq_domain_map function would hardcode the handler as
handle_level_irq, however qpnpint_irq_set_type would later override the
handler. Properly set the handler when the IRQ is mapped. This new code
doesn't return an error for IRQ_TYPE_NONE and preserves the existing
behavior of using handle_level_irq since there are some broken device
tree bindings that need to be corrected first.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Xingyu Chen [Thu, 17 Jan 2019 10:23:14 +0000 (11:23 +0100)]
pinctrl: meson: fix G12A ao pull registers base address
Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG
and AO_GPIO_O.
These bits of controlling output level are remapped to the new register
AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable.
These bits of controlling pull enable are remapped to the new register
AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling
pull type(up/down).
The new layout of ao gpio/pull registers is as follows:
- AO_GPIO_O_EN_N [offset: 0x9 << 2]
- AO_GPIO_I [offset: 0xa << 2]
- AO_RTI_PULL_UP_REG [offset: 0xb << 2]
- AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2]
- AO_GPIO_O [offset: 0xd << 2]
From above, we can see ao GPIO registers region has been separated by the
ao pull registers. In order to ensure the continuity of the region on
software, the ao GPIO and ao pull registers use the same base address, but
can be identified by the offset.
like pull-enable, pull should be optional has this region is available on
every controllers. Also, the g12a feature a new region "ds" for the
drive-strength
All this region thing is one big mess. I suspect that there is only one
big GPIO region with holes in it. All registers between the current
regions reads '0' so it is probably just spare space to handle more pins.
Since we need to continue to handle the existing controllers, switching to
one single region now would not simplify things. However, if more
organisation layouts and features keep on being added, we may have to look
at this again
Lars Poeschel [Fri, 11 Jan 2019 16:25:16 +0000 (17:25 +0100)]
pinctrl: mcp23s08: Allocate irq_chip dynamic
Keeping the irq_chip definition static shares it with multiple instances
of the mcp23s08 gpiochip in the system. This is bad and now we get this
warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from being driver static into the
struct mcp23s08. So a unique irq_chip is used for each gpiochip
instance.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Miquel Raynal [Tue, 8 Jan 2019 16:28:43 +0000 (17:28 +0100)]
pinctrl: armada-37xx: change suspend/resume time
Armada 3700 PCIe IP relies on the pinctrl IP managed by this
driver. For reasons related to the PCI core's organization when
suspending/resuming, PCI host controller drivers must reconfigure
their register at suspend_noirq()/resume_noirq() which happens after
suspend()/suspend_late() and before resume_early()/resume().
In the current state, after resuming from a suspend to RAM cycle the
PCIe IP is reconfigured before the pinctrl one which produces an
interrupt storm. The solution to support PCIe resume operation is to
change the "priority" of this pinctrl driver PM callbacks to
"_noirq()".
Brian Masney [Sat, 19 Jan 2019 20:42:40 +0000 (15:42 -0500)]
pinctrl: qcom: spmi-gpio: hardcode IRQ counts
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process. This change will also
allow for the removal of the interrupts property later in this
patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-gpio OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
The pm8941 code was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Brian Masney [Sat, 19 Jan 2019 20:42:39 +0000 (15:42 -0500)]
pinctrl: qcom: spmi-gpio: add support for three new variants
Add support for qcom,pm8005-gpio, qcom,pm8998-gpio, and
qcom,pmi8998-gpio. These three variants are already in use in some
arm64 dtsi files. Those boards work since the generic binding
qcom,spmi-gpio is also specified.
Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: sh-pfc: r8a7778: Fix HSPI pin numbers and names
When declaring the HSPI RX1_B and TX1_B pins, two mistakes were made:
- the rows and columns in the BGA pin matrix, from which the pin
numbers are derived, were exchanged,
- it was not taken into account that pin row labelling skips
characters I, O, Q, and S.
Fix the order, and the corresponding pin names.
Notes:
- The actual values of the pin numbers don't really matter (they just
have to be unique), so the wrong order didn't have any impact,
- Changing the names of the pins is user-visible, but there are no
users in (upstream) DTS files.
Fixes: 4f82e3ee724f1712 ("sh-pfc: Support pins not associated with a GPIO port") Fixes: 09cc76a95802e87d ("sh-pfc: r8a7778: add HSPI pin groups") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
pinctrl: sh-pfc: r8a77965: Replace DU_DOTCLKIN2 by DU_DOTCLKIN3
Unlike R-Car M3-W, R-Car M3-N does not have DU_DOTCLKIN2, but the
corresponding pin carries the DU_DOTCLKIN3 signal. Correct all
references to DU_DOTCLKIN2 to fix this.
This change does not have any runtime effect, as it only changes an
internal enum name, and a comment.
pinctrl: sh-pfc: r8a7791: Fix VIN1 versioned groups
The naming of the "b" versions of the VIN1 pin groups is a bit odd, in
that the "_b" appears in the middle of the names, instead of as a
suffix.
Increase consistency with other SoCs by making R-Car M2-W and M2-N, and
RZ/G1M and RZ/G1N, use the recently added optional "version" argument of
the VIN_DATA_PIN_GROUP() macro.
Note that this breaks backwards compatibility with existing DTBs, but
there are no upstream users of the "vin1_b_*" names.
Wolfram Sang [Mon, 7 Jan 2019 22:13:20 +0000 (23:13 +0100)]
pinctrl: sh-pfc: r8a7794: Initialize TDSEL register for ES1.0
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.35 in R-Car E2 v0.5). However, the reset value of the register is 0,
so software has to do it. Add this to the kernel driver to ensure this
is really done independent of firmware versions and use whitelisting for
ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Mon, 7 Jan 2019 22:13:19 +0000 (23:13 +0100)]
pinctrl: sh-pfc: r8a7790: Initialize TDSEL register for ES1.0
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.39 in R-Car H2 v0.91). However, the reset value of the register is
0, so software has to do it. Add this to the kernel driver to ensure
this is really done independent of firmware versions and use
whitelisting for ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode. For
me, TDSEL was not initialized by the firmware and I had problems with
the card when re-inserting it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The same can be expressed better by dropping the
SH_PFC_PIN_CFG_PULL_DOWN flag from the GPIO description, as it includes
returning an error to the caller when trying to configure the pin for
pull-down, causing:
sh-pfc e6060000.pin-controller: pin_config_set op failed for pin 201
sh-pfc e6060000.pin-controller: Error applying setting, reverse things back
sh-pfc e6060000.pin-controller: failed to select default state
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Takeshi Kihara [Wed, 12 Dec 2018 10:19:35 +0000 (19:19 +0900)]
pinctrl: sh-pfc: r8a77995: Fix MOD_SEL bit numbering
MOD_SEL register bit numbering was different from R-Car D3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Fixes: 794a67117646 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
[shimoda: split a patch per SoC and revise the commit log] Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use a macro to do the actual reordering] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Takeshi Kihara [Wed, 12 Dec 2018 10:19:34 +0000 (19:19 +0900)]
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL bit numbering
MOD_SEL register bit numbering was different from R-Car E3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Fixes: 6d4036a1e3b3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
[shimoda: Split a patch per SoC and revise the commit log] Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use macros to do the actual reordering] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Takeshi Kihara [Sat, 1 Dec 2018 07:02:20 +0000 (16:02 +0900)]
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit2 when using RX2, TX2 and SCK2
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and
SCK2_A pin functions are selected.
Takeshi Kihara [Sat, 1 Dec 2018 06:19:24 +0000 (15:19 +0900)]
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit3 when using TX0
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is
selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pins
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: sirf: atlas7: use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
pinctrl: mcp23s08: use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
chuanjia.liu [Thu, 3 Jan 2019 03:37:15 +0000 (11:37 +0800)]
pinctrl: mediatek: add EINT support to virtual GPIOs
Virtual gpio only used inside SOC and not being exported to outside SOC.
Some modules use virtual gpio as eint and doesn't need SMT.
So this patch add EINT support to virtual GPIOs.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Acked-by: Sean Wang <sean.wang@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Marek Behún [Fri, 21 Dec 2018 17:32:57 +0000 (18:32 +0100)]
pinctrl: armada-37xx: Correct mpp definitions
This is a cleanup and fix of the patch by Ken Ma <make@marvell.com>.
Fix the mpp definitions according to newest revision of the
specification:
- northbridge:
fix pmic1 gpio number to 7
fix pmic0 gpio number to 6
- southbridge
split pcie1 group bit mask to BIT(5) and BIT(9)
fix ptp group bit mask to BIT(11) | BIT(12) | BIT(13)
add smi group with bit mask BIT(4)
[gregory: split the pcie group in 2, as at hardware level they can be
configured separately] Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Aisheng Dong [Tue, 18 Dec 2018 15:22:58 +0000 (15:22 +0000)]
pinctrl: imx: add imx8qm driver
MX8QM contains a system controller that is responsible for controlling
the pad setting of the IPs that are present. Communication between the
host processor running an OS and the system controller happens through
a SCU protocol. This patch adds the SCU based MX8QM pinctrl driver.
Linus Torvalds [Mon, 7 Jan 2019 00:33:10 +0000 (16:33 -0800)]
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Linus Torvalds [Mon, 7 Jan 2019 00:30:14 +0000 (16:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
Linus Torvalds [Sun, 6 Jan 2019 01:50:59 +0000 (17:50 -0800)]
Change mincore() to count "mapped" pages rather than "cached" pages
The semantics of what "in core" means for the mincore() system call are
somewhat unclear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache" rather than "page is mapped in the mapping".
The problem with that traditional semantic is that it exposes a lot of
system cache state that it really probably shouldn't, and that users
shouldn't really even care about.
So let's try to avoid that information leak by simply changing the
semantics to be that mincore() counts actual mapped pages, not pages
that might be cheaply mapped if they were faulted (note the "might be"
part of the old semantics: being in the cache doesn't actually guarantee
that you can access them without IO anyway, since things like network
filesystems may have to revalidate the cache before use).
In many ways the old semantics were somewhat insane even aside from the
information leak issue. From the very beginning (and that beginning is
a long time ago: 2.3.52 was released in March 2000, I think), the code
had a comment saying
Later we can get more picky about what "in core" means precisely.
and this is that "later". Admittedly it is much later than is really
comfortable.
NOTE! This is a real semantic change, and it is for example known to
change the output of "fincore", since that program literally does a
mmmap without populating it, and then doing "mincore()" on that mapping
that doesn't actually have any pages in it.
I'm hoping that nobody actually has any workflow that cares, and the
info leak is real.
We may have to do something different if it turns out that people have
valid reasons to want the old semantics, and if we can limit the
information leak sanely.
Cc: Kevin Easton <kevin@guarana.org> Cc: Jiri Kosina <jikos@kernel.org> Cc: Masatake YAMATO <yamato@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 19:15:04 +0000 (11:15 -0800)]
Fix 'acccess_ok()' on alpha and SH
Commit 594cc251fdd0 ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net> Cc: Matt Turner <mattst88@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 20:19:23 +0000 (12:19 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Fix a number of ext4 bugs"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix special inode number checks in __ext4_iget()
ext4: track writeback errors using the generic tracking infrastructure
ext4: use ext4_write_inode() when fsyncing w/o a journal
ext4: avoid kernel warning when writing the superblock to a dead device
ext4: fix a potential fiemap/page fault deadlock w/ inline_data
ext4: make sure enough credits are reserved for dioread_nolock writes
Linus Torvalds [Sun, 6 Jan 2019 19:47:26 +0000 (11:47 -0800)]
Merge tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions introduced in this cycles:
- fix dma-debug tracking for the map_page / map_single
consolidatation
- properly stub out DMA mapping symbols for !HAS_DMA builds to avoid
link failures
- fix AMD Gart direct mappings
- setup the dma address for no kernel mappings using the remap
allocator"
* tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING for remapped allocations
x86/amd_gart: fix unmapping of non-GART mappings
dma-mapping: remove a few unused exports
dma-mapping: properly stub out the DMA API for !CONFIG_HAS_DMA
dma-mapping: remove dmam_{declare,release}_coherent_memory
dma-mapping: implement dmam_alloc_coherent using dmam_alloc_attrs
dma-mapping: implement dma_map_single_attrs using dma_map_page_attrs
Linus Torvalds [Sun, 6 Jan 2019 19:40:06 +0000 (11:40 -0800)]
Merge tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- Changes for EC_MKBP_EVENT_SENSOR_FIFO handling.
- Also, maintainership changes. Olofj out, Enric balletbo in.
* tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
MAINTAINERS: add maintainers for ChromeOS EC sub-drivers
MAINTAINERS: platform/chrome: Add Enric as a maintainer
MAINTAINERS: platform/chrome: remove myself as maintainer
platform/chrome: don't report EC_MKBP_EVENT_SENSOR_FIFO as wakeup
platform/chrome: straighten out cros_ec_get_{next,host}_event() error codes
Eric Biggers [Sun, 6 Jan 2019 13:36:21 +0000 (08:36 -0500)]
fscrypt: add Adiantum support
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit 059c2a4d8e16 ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sun, 6 Jan 2019 02:35:02 +0000 (18:35 -0800)]
Merge tag 'docs-5.0-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"
* tag 'docs-5.0-fixes' of git://git.lwn.net/linux:
doc: filesystems: fix bad references to nonexistent ext4.rst file
Documentation/admin-guide: update URL of LKML information link
Docs/kernel-api.rst: Remove blk-tag.c reference
Linus Torvalds [Sun, 6 Jan 2019 02:33:21 +0000 (18:33 -0800)]
Merge tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"Remove an explicit dependency in Kconfig which is implied by another
dependency"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: Remove depends on HAS_DMA in case of platform dependency
Linus Torvalds [Sun, 6 Jan 2019 02:29:13 +0000 (18:29 -0800)]
Merge tag 'for-linus-20190104' of git://git.kernel.dk/linux-block
Pull block updates and fixes from Jens Axboe:
- Pulled in MD changes that Shaohua had queued up for 4.21.
Unfortunately we lost Shaohua late 2018, I'm sending these in on his
behalf.
- In conjunction with the above, I added a CREDITS entry for Shaoua.
- sunvdc queue restart fix (Ming)
* tag 'for-linus-20190104' of git://git.kernel.dk/linux-block:
Add CREDITS entry for Shaohua Li
block: sunvdc: don't run hw queue synchronously from irq context
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
Linus Torvalds [Sun, 6 Jan 2019 02:25:19 +0000 (18:25 -0800)]
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Linus Torvalds [Sun, 6 Jan 2019 02:20:51 +0000 (18:20 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Over the break a few defects were found, so this is a -rc style pull
request of various small things that have been posted.
- An attempt to shorten RCU grace period driven delays showed crashes
during heavier testing, and has been entirely reverted
- A missed merge/rebase error between the advise_mr and ib_device_ops
series
- Some small static analysis driven fixes from Julia and Aditya
- Missed ability to create a XRC_INI in the devx verbs interop
series"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
infiniband/qedr: Potential null ptr dereference of qp
infiniband: bnxt_re: qplib: Check the return value of send_message
IB/ipoib: drop useless LIST_HEAD
IB/core: Add advise_mr to the list of known ops
Revert "IB/mlx5: Fix long EEH recover time with NVMe offloads"
IB/mlx5: Allow XRC INI usage via verbs in DEVX context
Linus Torvalds [Sun, 6 Jan 2019 02:15:37 +0000 (18:15 -0800)]
Merge tag 'fbdev-v4.21' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"This time the pull request is really small.
The most notable changes are fixing fbcon to not cause crash on
unregister_framebuffer() operation when there is more than one
framebuffer, adding config option to center the bootup logo and making
FB_BACKLIGHT config option tristate (which in turn uncovered incorrect
FB_BACKLIGHT usage by DRM's nouveau driver).
Summary:
- fix fbcon to not cause crash on unregister_framebuffer() when there
is more than one framebuffer (Noralf Trønnes)
- improve support for small rotated displays (Peter Rosin)
- fix probe failure handling in udlfb driver (Dan Carpenter)
- add config option to center the bootup logo (Peter Rosin)
- make FB_BACKLIGHT config option tristate (Rob Clark)
- remove superfluous HAS_DMA dependency for goldfishfb driver (Geert
Uytterhoeven)
- misc fixes (Alexey Khoroshilov, YueHaibing, Colin Ian King, Lubomir
Rintel)
- misc cleanups (Yangtao Li, Wen Yang)
also there is DRM's nouveau driver fix for wrong FB_BACKLIGHT config
option usage (FB_BACKLIGHT is for internal fbdev subsystem use only)"
* tag 'fbdev-v4.21' of git://github.com/bzolnier/linux:
drm/nouveau: fix incorrect FB_BACKLIGHT usage in Kconfig
fbdev: fbcon: Fix unregister crash when more than one framebuffer
fbdev: Remove depends on HAS_DMA in case of platform dependency
pxa168fb: trivial typo fix
fbdev: fsl-diu: remove redundant null check on cmap
fbdev: omap2: omapfb: convert to DEFINE_SHOW_ATTRIBUTE
fbdev: uvesafb: fix spelling mistake "memoery" -> "memory"
fbdev: fbmem: add config option to center the bootup logo
fbdev: fbmem: make fb_show_logo_line return the end instead of the height
video: fbdev: pxafb: Fix "WARNING: invalid free of devm_ allocated data"
fbdev: fbmem: behave better with small rotated displays and many CPUs
video: clps711x-fb: release disp device node in probe()
fbdev: make FB_BACKLIGHT a tristate
udlfb: fix some inconsistent NULL checking
Linus Torvalds [Sun, 6 Jan 2019 02:13:35 +0000 (18:13 -0800)]
Merge branch 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has only driver updates for you this time.
Mostly new IDs/DT compatibles, also SPDX conversions, small cleanups.
STM32F7 got FastMode+ and PM support, Axxia some reliabilty
improvements"
* 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: Add Actions Semiconductor Owl family S700 I2C support
dt-bindings: i2c: Add S700 support for Actions Semi Soc's
i2c: ismt: Add support for Intel Cedar Fork
i2c: tegra: Switch to SPDX identifier
i2c: tegra: Add missing kerneldoc for some fields
i2c: tegra: Cleanup kerneldoc comments
i2c: axxia: support sequence command mode
dt-bindings: i2c: rcar: Add r8a774c0 support
dt-bindings: i2c: sh_mobile: Add r8a774c0 support
i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)
i2c: i2c-cros-ec-tunnel: Switch to SPDX identifier.
i2c: powermac: Use of_node_name_eq for node name comparisons
i2c-axxia: check for error conditions first
i2c-axxia: dedicated function to set client addr
dt-bindings: i2c: Use correct vendor prefix for Atmel
i2c: tegra: replace spin_lock_irqsave with spin_lock in ISR
eeprom: at24: add support for 24c2048
dt-bindings: eeprom: at24: add "atmel,24c2048" compatible string
i2c: i2c-stm32f7: add PM Runtime support
i2c: sh_mobile: add support for r8a77990 (R-Car E3)
...
Linus Torvalds [Sun, 6 Jan 2019 01:53:40 +0000 (17:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
Masahiro Yamada [Thu, 3 Jan 2019 01:10:39 +0000 (10:10 +0900)]
arch: remove redundant UAPI generic-y defines
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:38 +0000 (10:10 +0900)]
kbuild: generate asm-generic wrappers if mandatory headers are missing
Some time ago, Sam pointed out a certain degree of overwrap between
generic-y and mandatory-y. (https://lkml.org/lkml/2017/7/10/121)
I tweaked the meaning of mandatory-y a little bit; now it defines the
minimum set of ASM headers that all architectures must have.
If arch does not have specific implementation of a mandatory header,
Kbuild will let it fallback to the asm-generic one by automatically
generating a wrapper. This will allow to drop lots of redundant
generic-y defines.
Previously, "mandatory" was used in the context of UAPI, but I guess
this can be extended to kernel space ASM headers.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Mon, 31 Dec 2018 08:24:09 +0000 (17:24 +0900)]
kbuild: change filechk to surround the given command with { }
filechk_* rules often consist of multiple 'echo' lines. They must be
surrounded with { } or ( ) to work correctly. Otherwise, only the
string from the last 'echo' would be written into the target.
Let's take care of that in the 'filechk' in scripts/Kbuild.include
to clean up filechk_* rules.
Masahiro Yamada [Mon, 31 Dec 2018 04:09:00 +0000 (13:09 +0900)]
kbuild: clean up rule_dtc_dt_yaml
Commit 3a2429e1faf4 ("kbuild: change if_changed_rule for multi-line
recipe") and commit 4f0e3a57d6eb ("kbuild: Add support for DT binding
schema checks") came in via different sub-systems.
Mathias Krause [Sun, 30 Dec 2018 12:36:00 +0000 (13:36 +0100)]
kallsyms: lower alignment on ARM
As mentioned in the info pages of gas, the '.align' pseudo op's
interpretation of the alignment value is architecture specific.
It might either be a byte value or taken to the power of two.
On ARM it's actually the latter which leads to unnecessary large
alignments of 16 bytes for 32 bit builds or 256 bytes for 64 bit
builds.
Fix this by switching to '.balign' instead which is consistent
across all architectures.
Julia Lawall [Sat, 29 Dec 2018 06:14:16 +0000 (07:14 +0100)]
scripts: coccinelle: boolinit: drop warnings on named constants
Coccinelle doesn't always have access to the values of named
(#define) constants, and they may likely often be bound to true
and false values anyway, resulting in false positives. So stop
warning about them.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
projects / linux.git / log