gpio_hog depends on gdev field being initialized. This patch fixes an
OOPs during initialization of TI's AM335x-ICEv2.
Fixes: 3edfb7bd76bd1cba ("gpiolib: Show correct direction from the beginning") Tested-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
The function is about adding a gpio_chip so dev has to belong to this
one. Fix wording to be more grammatically correct (but attention, I'm
not a native speaker).
Marek Vasut [Wed, 3 Oct 2018 22:52:52 +0000 (00:52 +0200)]
gpio: syscon: Fix possible NULL ptr usage
The priv->data->set can be NULL while flags contains GPIO_SYSCON_FEAT_OUT
and chip->set is valid pointer. This happens in case the controller uses
the default GPIO setter. Always use chip->set to access the setter to avoid
possible NULL pointer dereferencing.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
gpio: mockup: use device properties instead of platform_data
Some users want to introduce device tree support to the mockup driver.
Let's make it easier by switching to using generic device properties.
The driver stays compatible with previous use cases and after this
conversion there'll be no need to change the way probing of mockup
GPIO chips works.
Linus Walleij [Mon, 1 Oct 2018 21:06:17 +0000 (23:06 +0200)]
gpio: Slightly more helpful debugfs
This at least makes debugfs print if the line is active
high or low. That is pretty helpful as what we display
as "lo" or "hi" is the raw physical level of the line.
gpio: omap: Remove set but not used variable 'dev'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpio/gpio-omap.c: In function 'gpio_omap_cpu_notifier':
drivers/gpio/gpio-omap.c:1327:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
Documentation/devicetree/bindings/gpio/gpio.txt says: "The names are
assigned starting from line offset 0 from left to right from the
passed array. An incomplete array (where the number of passed named
are less than ngpios) will still be used up until the last provided
valid line index". This patch makes it actually work this way.
gpio: omap: get rid of the conditional PM runtime calls
OMAP GPIO driver is checking !BANK_USED() used condition before calling PM
runtime API, because of PM runtime calls in
omap2_gpio_prepare/resume_for_idle(). It's not required any more since
"omap gpio add level idle, cpu_pm and drop runtime_irq_safe" series [1]
from Tony Lindgren was accepted and PM runtime management was enabled in
IRQ chip core by commit be45beb2df69 ("genirq: Add runtime power management
support for IRQ chips") .
As result safely drop !BANK_USED() checks from omap_gpio_request/free(),
omap_gpio_irq_bus_lock/unlock() and enable PM runtime management for OMAP
GPIO IRQ chip.
gpio: htc-egpio: Remove set but not used variable 'bit'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpio/gpio-htc-egpio.c: In function 'egpio_set':
drivers/gpio/gpio-htc-egpio.c:192:20: warning:
variable 'bit' set but not used [-Wunused-but-set-variable]
gpio: Propagate errors from gpiod_set_array_value_complex()
Internal helper function gpiod_set_array_value_complex() was changed to
return an error value, but not all gpiolib callers were updated to
propagate the new error up.
Documentation: gpio: Fix return type of gpiod_set_raw_array_value*()
The return type of gpiod_set_raw_array_value() and
gpiod_set_raw_array_value_cansleep() was changed from void to int, but
the doc update was forgotten.
gpiolib: Fix incorrect use of find_next_zero_bit()
Commit b17566a6b08b ("gpiolib: Implement fast processing path in
get/set array"), already fixed to some extent with commit 5d581d7e8cdc
("gpiolib: Fix missing updates of bitmap index"), introduced a new mode
of processing bitmaps where bits applicable for fast bitmap processing
path are supposed to be skipped while iterating bits which don't apply.
Unfortunately, find_next_zero_bit() function supposed to skip over
those fast bits is always called with a 'start' argument equal to an
index of last zero bit found and returns that index value again an
again, causing an infinite loop.
Fix it by incrementing the index uncoditionally before
find_next_zero_bit() is optionally called.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tony Lindgren [Thu, 20 Sep 2018 19:35:32 +0000 (12:35 -0700)]
gpio: omap: Get rid of pm_runtime_irq_safe()
If a gpio instance has any GPIO bits requested we do a pm_runtime_get()
on the device. Now with cpu_pm handling the deeper SoC idle state quirks,
let's just remove pm_runtime_irq_safe() call and add a warning in case we
ever happen to encounter it.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tony Lindgren [Thu, 20 Sep 2018 19:35:31 +0000 (12:35 -0700)]
gpio: omap: Remove custom PM calls and use cpu_pm instead
For a long time the gpio-omap custom PM calls have been annoying me so
let's replace them with cpu_pm instead. This will enable GPIO PM for
deeper idle states on omap4. And we can handle GPIO PM for omap2/3/4
in the same way.
Note that with this patch we are also slightly changing GPIO PM to be
less aggressive for omap3 and only will idle GPIO when PER context
may be lost.
For omap2, we don't need to save context and don't want to remove any
triggering so let's add a quirk flag for that.
Let's do this all in a single patch to avoid a situation where old
custom calls still are used with new code.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tony Lindgren [Thu, 20 Sep 2018 19:35:30 +0000 (12:35 -0700)]
gpio: omap: Add level wakeup handling for omap4 based SoCs
I noticed that unlike omap2 and 3 based SoCs, omap4 based SoCs keep
the GPIO clocks enabled for GPIO level interrupts with wakeup enabled.
This blocks deeper idle states as the whole domain will stay busy.
The GPIO functional clock seems to stay enabled if the wakeup register
is enabled and a level interrupt is triggered. In that case the only
way to have the GPIO module idle is to reset it. It is possible this
has gone unnoticed with OSWR (Open SWitch Retention) and off mode
during idle resetting GPIO context most GPIO instances in the earlier
Android trees for example.
Looks like the way to deal with this is to have omap4 based SoCs
only set wake for the duration of idle for level interrupts, and clear
level registers for the idle. With level interrupts we can do this as
the level interrupt from device will be still there on resume.
I've taken the long path to fixing this to avoid yet more hard to
read code. I've set up a quirks flag, and a struct for function
pointers so we can use these to clean up other quirk handling easier
in the later patches. The current level quirk handling is moved to
the new functions.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib: Fix array members of same chip processed separately
New code introduced by commit bf9346f5d47b ("gpiolib: Identify arrays
matching GPIO hardware") forcibly tries to find an array member which
has its array index number equal to its hardware pin number and set
up an array info for possible fast bitmap processing of all arrray
pins belonging to that chip which also satisfy that numbering rule.
Depending on array content, it may happen that consecutive array
members which belong to the same chip but don't have array indexes
equal to their pin hardware numbers will be split into groups, some of
them processed together via the fast bitmap path, and rest of them
separetely. However, applications may expect all those pins being
processed together with a single call to .set_multiple() chip callback,
like that was done before the change.
Limit applicability of fast bitmap processing path to cases where all
pins of consecutive array members starting from 0 which belong to the
same chip have their hardware numbers equal to their corresponding
array indexes. That should still speed up processing of applications
using whole GPIO banks as I/O ports, while not breaking simultaneous
manipulation of consecutive pins of the same chip which don't follow
the equal numbering rule.
Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In new code introduced by commit b17566a6b08b ("gpiolib: Implement fast
processing path in get/set array"), bitmap index is not updated with
next found zero bit position as it should while skipping over pins
already processed via fast bitmap path, possibly resulting in an
infinite loop. Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Give the HTC EGPIO chips unique names, htc-egpio-0,
htc-egpio-1 etc, so that it gets possible to associate
machine descriptor tables with individual chips.
We remove the references to anything but two-cell GPIO specifiers
and just mention that controllers need to specify their bindings
and that we strongly recommend two-cell bindings.
Cc: devicetree@vger.kernel.org Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: OF: Cut painful BNF experiments from bindings
In 2011 the commit bf859f84a19f
("gpio/dt: Refine GPIO device tree binding") introduced an
experimental BNF notation for defining a regular grammar for
the GPIO phandles used by different devices.
This was an interesting approach, and shows that we have long
nutured the idea to formally verify device tree files using
regular grammar.
Most if not all other bindings use natural language to define
the bindings, and the recent thinking for verifying device
tree files is to use JSON schemas in separate definitions.
Cut the BNF business and replace it with natural language
so that it becomes more human-readable for now.
Cc: devicetree@vger.kernel.org Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Kumar Gala <galak@kernel.crashing.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew F. Davis [Fri, 31 Aug 2018 19:13:26 +0000 (14:13 -0500)]
gpio: davinci: Move driver local definitions to driver
These defines, structs and inline functions are used only internally by
the driver, they do not belong in platform_data. Move them.
Signed-off-by: Andrew F. Davis <afd@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew F. Davis [Fri, 31 Aug 2018 19:13:25 +0000 (14:13 -0500)]
gpio: davinci: Remove unneeded GPIO macro
This macro does nothing and has only one user, remove it.
Signed-off-by: Andrew F. Davis <afd@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew F. Davis [Fri, 31 Aug 2018 19:13:24 +0000 (14:13 -0500)]
gpio: davinci: Allocate the correct amount of memory for controller
Previously we created a controller structure per bank of GPIO pins. This
has since been changed to one per controller, but the allocation size
was not changed. Fix this here.
This also leaves the variable 'nbank' unused, instead of removing it,
move it down and use it to clean up a loop. For loops with multiple
initializers and/or iteration expressions, especially ones that don't
use those loop counters are quite hard to follow, fix this.
Signed-off-by: Andrew F. Davis <afd@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew F. Davis [Fri, 31 Aug 2018 19:13:23 +0000 (14:13 -0500)]
gpio: davinci: Use dev name for label and automatic base selection
Use dev_name to get a unique label and use -1 for a base to get our
selection automatically. We pull in all GPIOs per chip now so this
does not have the effect of out of order labels like before.
We do these both together so we can drop all the static data in one
patch. This also lets us normalize the return paths as we don't need
any cleanup after this change.
Signed-off-by: Andrew F. Davis <afd@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew F. Davis [Fri, 31 Aug 2018 19:13:22 +0000 (14:13 -0500)]
gpio: davinci: Remove unused member of davinci_gpio_controller
This was added as part of the patch in the fixes below, but was
not needed or used, remove this here.
Fixes: 8e11047b8f3c ("gpio: davinci: Add support for multiple GPIO controllers") Tested-by: Keerthy <j-keerthy@ti.com> Acked-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A bunch of core gpiolib files still include the <linux/gpio.h>
legacy API header for no good reason. After this only the
gpiolib-legacy.c file includes it, which is fine.
The sysfs ABI code has a pointless wrapper function around
gpio_to_desc() we can just loose.
Cc: patches@opensource.cirrus.com Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: Mark Brown <broonie@kernel.org> Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are GPIO drivers so just include <linux/gpio/driver.h>.
Cc: patches@opensource.cirrus.com Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: Mark Brown <broonie@kernel.org> Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hans Verkuil [Fri, 14 Sep 2018 08:36:39 +0000 (10:36 +0200)]
gpiolib: check if irqchip already has the irq hook replacements
Some drivers use a single irqchip for multiple gpiochips. As a result the
irqchip hooks are overridden for the first gpiochip that was added, but
for the other gpiochip instances this should not happen again, otherwise
we would go into an infinite recursion.
Check for this, but also log a message that the driver should be fixed
since this is bad practice.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wolfram Sang [Wed, 11 Jul 2018 16:33:19 +0000 (18:33 +0200)]
gpiolib: use better errno if get_direction is not available
EINVAL is very generic, use ENOTSUPP in case the gpiochip does not
provide this function. While removing the assignment from the 'status'
variable, use better indentation in the declaration block.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib: Implement fast processing path in get/set array
Certain GPIO descriptor arrays returned by gpio_get_array() may contain
information on direct mapping of array members to pins of a single GPIO
chip in hardware order. In such cases, bitmaps of values can be passed
directly from/to the chip's .get/set_multiple() callbacks without
wasting time on iterations.
Add respective code to gpiod_get/set_array_bitmap_complex() functions.
Pins not applicable for fast path are processed as before, skipping
over the 'fast' ones.
Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib: Pass array info to get/set array functions
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO array lookup results may map directly to GPIO pins of a
single GPIO chip in hardware order. If that condition is recognized
and handled efficiently, significant performance gain of get/set array
functions may be possible.
While processing a request for an array of GPIO descriptors, identify
those which represent corresponding pins of a single GPIO chip. Skip
over pins which require open source or open drain special processing.
Moreover, identify pins which require inversion. Pass a pointer to
that information with the array to the caller so it can benefit from
enhanced performance as soon as get/set array functions can accept and
make efficient use of it.
Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib: Pass bitmaps, not integer arrays, to get/set array
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Uwe Kleine-König [Mon, 20 Aug 2018 06:32:53 +0000 (08:32 +0200)]
gpiolib: Don't support irq sharing for userspace
This concerns gpio edge detection for GPIO IRQs used from
userspace for GPIO event listeners.
Trying to work out the right event if it's not sure that the
examined gpio actually moved is impossible.
Consider two gpios "gpioA" and "gpioB" that share an interrupt.
gpioA's irq should trigger on any edge, gpioB's on a falling edge.
If now the common irq fires and both gpio lines are high, there
are several possibilities that could have happend:
a) gpioA just had a low-to-high edge
b) gpioB just had a high-to-low-to-high spike
c) a combination of both a) and b)
While c) is unlikely (in most setups) a) and b) alone are bad
enough. Currently the code assumes case a) unconditionally and
doesn't report an event for gpioB. Note that even if there is no
irq sharing involved a spike for a gpio might not result in an
event if it's configured to trigger for a single edge only.
The only way to improve this is to drop support for interrupt
sharing. This way a spike results in an event for the right gpio
at least. Note that apart from dropping IRQF_SHARED this
effectively undoes commit df1e76f28ffe
("gpiolib: skip unwanted events, don't convert them to opposite edge").
This obviously breaks setups that rely on interrupt sharing,
but given that this cannot be reliable, this is probably an
acceptable trade-off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Assuming there are no users of interrupt sharing yet] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI chipselects are assumed to be active low in the current
binding, so when we want to use GPIO descriptors and handle
the active low/high semantics in gpiolib, we need a special
parsing quirk to deal with this.
We check for the property "spi-cs-high" and if that is
NOT present we assume the CS line is active low.
If the line is tagged as active low in the device tree and
has no "spi-cs-high" property all is fine, the device
tree and the SPI bindings are in agreement.
If the line is tagged as active high in the device tree with
the second cell flag and has no "spi-cs-high" property we
enforce active low semantics (as this is the exception we can
just tag on the flag).
If the line is tagged as active low with the second cell flag
AND tagged with "spi-cs-high" the SPI active high property
takes precedence and we print a warning.
Cc: Mark Brown <broonie@kernel.org> Cc: linux-spi@vger.kernel.org Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hans Verkuil [Sat, 8 Sep 2018 09:23:17 +0000 (11:23 +0200)]
gpiolib: override irq_enable/disable
When using the gpiolib irqchip helpers install irq_enable/disable
hooks for the irqchip to ensure that gpiolib knows when the irq
is enabled or disabled, allowing drivers to disable the irq and then
use it as an output pin, and later switch the direction to input and
re-enable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hans Verkuil [Sat, 8 Sep 2018 09:23:16 +0000 (11:23 +0200)]
gpiolib: add flag to indicate if the irq is disabled
GPIO drivers call gpiochip_(un)lock_as_irq whenever they want to use a gpio
as an interrupt. This is done when the irq is requested and it marks the
gpio as in use by an interrupt.
This is problematic for cases where a gpio pin is used as an interrupt
pin, then, after the irq is disabled, is used as a regular gpio pin.
Currently it is not possible to do this other than by first freeing
the interrupt so gpiochip_unlock_as_irq is called, since an attempt to
switch the gpio direction for output will fail since gpiolib believes
that the gpio is in use for an interrupt and it does not know that it
the irq is actually disabled.
There are currently two drivers that would like to be able to do this:
the tda998x_drv.c driver where a regular gpio pin needs to be temporarily
reconfigured as an interrupt pin during CEC calibration, and the cec-gpio
driver where you want to configure the gpio pin as an interrupt while
waiting for traffic over the CEC bus, or as a regular pin when receiving or
transmitting a CEC message.
The solution is to add a new flag that is set when the irq is enabled,
and have gpiod_direction_output check for that flag.
We also add functions that drivers that do not use GPIOLIB_IRQCHIP
can call when they enable/disable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hans Verkuil [Sat, 8 Sep 2018 09:23:14 +0000 (11:23 +0200)]
gpiolib: export gpiochip_irq_reqres/relres()
GPIO drivers that do not use GPIOLIB_IRQCHIP can hook these into
the irq_request_resource and irq_release_resource callbacks of the
irq_chip so they correctly 'get' the module and lock the gpio line
for IRQ use.
This will simplify driver code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Colin Ian King [Thu, 6 Sep 2018 11:58:30 +0000 (12:58 +0100)]
gpio: ep93xx: fix incorrect array element size check
Currently the while loop checks for the end of the array using
the size of egp->gc rather that the number of elements in the array,
so fix this. Also, perform the array size check first as stylistically
it is always good to bounds check on an array first before referencing
the array (in this case, we're just computing the address of an
element in an array so this is a moot point).
Fixes: fd935fc421e7 ("gpio: ep93xx: Do not pingpong irq numbers") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's nice to use BIT() macros rather than open coding the same.
It's good practice as sometimes people use BIT(31) and forget
that the constant must be cast unsigned long.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 29 Aug 2018 15:16:18 +0000 (17:16 +0200)]
gpio: ts5500: Delete platform data handling
The TS5500 GPIO driver apparently supports platform data
without making any use of it whatsoever. Delete this code,
last chance to speak up if you think it is needed.
Linus Walleij [Wed, 29 Aug 2018 15:02:16 +0000 (17:02 +0200)]
gpio: mxs: Get rid of external API call
The MXS driver was calling back into the GPIO API from
its irqchip. This is not very elegant, as we are a driver,
let's just shortcut back into the gpio_chip .get() function
instead.
This is a tricky case since the .get() callback is not in
this file, instead assigned by bgpio_init(). Calling the
function direcly in the gpio_chip is however the lesser
evil.
Justin Chen [Fri, 17 Aug 2018 23:47:39 +0000 (16:47 -0700)]
gpio: brcmstb: allow 0 width GPIO banks
Sometimes we have empty banks within the GPIO block. This commit allows
proper handling of 0 width GPIO banks. We handle 0 width GPIO banks by
incrementing the bank and number of GPIOs, but not initializing them.
This will mean a call into the non-existent GPIOs will return an error.
Also remove "GPIO registered" dev print. This information is misleading
since the incremented banks and gpio_base do not reflect the actual GPIOs
that get initialized. We leave this information out since it is already
printed with dev_dbg.
Linus Walleij [Mon, 27 Aug 2018 20:15:51 +0000 (22:15 +0200)]
gpio: ftgpio: Support debounce timer
The FTGPIO010 has a debounce timer or rather prescaler that
will affect interrupts fireing off the block. We can support
this to get proper debounce on e.g. keypresses.
Since the same prescaler is used across all GPIO lines of
the silicon block, we need to bail out if the prescaler is
already set and in use by another line.
If the prescaler is already set to what we need, fine, we
reuse it. This happens more often than not when the same
debounce time is set for several GPIO keys, so we support
that usecase easily with this code.
Linus Walleij [Mon, 27 Aug 2018 20:15:40 +0000 (22:15 +0200)]
gpio: ftgpio: Support optional silicon clock
The GPIO silicon is clocked with a PCLK (peripheral clock)
on all systems, however not all platforms model it and include
it in e.g. the device tree, so add clock handling but make it
optional so we bail out safely if it is e.g. always on.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Robert Jarzmik [Sat, 25 Aug 2018 08:44:17 +0000 (10:44 +0200)]
gpio: pxa: handle corner case of unprobed device
In the corner case where the gpio driver probe fails, for whatever
reason, the suspend and resume handlers will still be called as they
have to be registered as syscore operations. This applies as well when
no probe was called while the driver has been built in the kernel.
Nicolas tracked this in :
https://bugzilla.kernel.org/show_bug.cgi?id=200905
Therefore, add a failsafe in these function, and test if a proper probe
succeeded and the driver is functional.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reported-by: Nicolas Chauvet <kwizart@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>