Most (all?) x86 platforms provide a port IO based reset mechanism, e.g.
OUT 92h or CF9h. Userspace may emulate said mechanism, i.e. reset a
vCPU in response to KVM_EXIT_IO, without explicitly announcing to KVM
that it is doing a reset, e.g. Qemu jams vCPU state and resumes running.
To avoid corruping %rip after such a reset, commit 0967b7bf1c22 ("KVM:
Skip pio instruction when it is emulated, not executed") changed the
behavior of PIO handlers, i.e. today's "fast" PIO handling to skip the
instruction prior to exiting to userspace. Full emulation doesn't need
such tricks becase re-emulating the instruction will naturally handle
%rip being changed to point at the reset vector.
Updating %rip prior to executing to userspace has several drawbacks:
- Userspace sees the wrong %rip on the exit, e.g. if PIO emulation
fails it will likely yell about the wrong address.
- Single step exits to userspace for are effectively dropped as
KVM_EXIT_DEBUG is overwritten with KVM_EXIT_IO.
- Behavior of PIO emulation is different depending on whether it
goes down the fast path or the slow path.
Rather than skip the PIO instruction before exiting to userspace,
snapshot the linear %rip and cancel PIO completion if the current
value does not match the snapshot. For a 64-bit vCPU, i.e. the most
common scenario, the snapshot and comparison has negligible overhead
as VMCS.GUEST_RIP will be cached regardless, i.e. there is no extra
VMREAD in this case.
All other alternatives to snapshotting the linear %rip that don't
rely on an explicit reset announcenment suffer from one corner case
or another. For example, canceling PIO completion on any write to
%rip fails if userspace does a save/restore of %rip, and attempting to
avoid that issue by canceling PIO only if %rip changed then fails if PIO
collides with the reset %rip. Attempting to zero in on the exact reset
vector won't work for APs, which means adding more hooks such as the
vCPU's MP_STATE, and so on and so forth.
Checking for a linear %rip match technically suffers from corner cases,
e.g. userspace could theoretically rewrite the underlying code page and
expect a different instruction to execute, or the guest hardcodes a PIO
reset at 0xfffffff0, but those are far, far outside of what can be
considered normal operation.
Fixes: 432baf60eee3 ("KVM: VMX: use kvm_fast_pio_in for handling IN I/O") Cc: <stable@vger.kernel.org> Reported-by: Jim Mattson <jmattson@google.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vitaly Kuznetsov [Wed, 13 Mar 2019 17:13:42 +0000 (18:13 +0100)]
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
When userspace initializes guest vCPUs it may want to zero all supported
MSRs including Hyper-V related ones including HV_X64_MSR_STIMERn_CONFIG/
HV_X64_MSR_STIMERn_COUNT. With commit f3b138c5d89a ("kvm/x86: Update SynIC
timers on guest entry only") we began doing stimer_mark_pending()
unconditionally on every config change.
The issue I'm observing manifests itself as following:
- Qemu writes 0 to STIMERn_{CONFIG,COUNT} MSRs and marks all stimers as
pending in stimer_pending_bitmap, arms KVM_REQ_HV_STIMER;
- kvm_hv_has_stimer_pending() starts returning true;
- kvm_vcpu_has_events() starts returning true;
- kvm_arch_vcpu_runnable() starts returning true;
- when kvm_arch_vcpu_ioctl_run() gets into
(vcpu->arch.mp_state == KVM_MP_STATE_UNINITIALIZED) case:
- kvm_vcpu_block() gets in 'kvm_vcpu_check_block(vcpu) < 0' and returns
immediately, avoiding normal wait path;
- -EAGAIN is returned from kvm_arch_vcpu_ioctl_run() immediately forcing
userspace to retry.
So instead of normal wait path we get a busy loop on all secondary vCPUs
before they get INIT signal. This seems to be undesirable, especially given
that this happens even when Hyper-V extensions are not used.
Generally, it seems to be pointless to mark an stimer as pending in
stimer_pending_bitmap and arm KVM_REQ_HV_STIMER as the only thing
kvm_hv_process_stimers() will do is clear the corresponding bit. We may
just not mark disabled timers as pending instead.
Fixes: f3b138c5d89a ("kvm/x86: Update SynIC timers on guest entry only") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xiaoyao Li [Fri, 8 Mar 2019 07:57:20 +0000 (15:57 +0800)]
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
Since MSR_IA32_ARCH_CAPABILITIES is emualted unconditionally even if
host doesn't suppot it. We should move it to array emulated_msrs from
arry msrs_to_save, to report to userspace that guest support this msr.
Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes: 1eaafe91a0df4 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported") Cc: stable@vger.kernel.org Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function irqfd_wakeup() has flags defined as __poll_t and then it
has additional flags which is used for irqflags.
Redefine the inner flags variable as iflags so it does not shadow the
outer flags.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ben Gardon [Tue, 12 Mar 2019 18:45:59 +0000 (11:45 -0700)]
kvm: mmu: Used range based flushing in slot_handle_level_range
Replace kvm_flush_remote_tlbs with kvm_flush_remote_tlbs_with_address
in slot_handle_level_range. When range based flushes are not enabled
kvm_flush_remote_tlbs_with_address falls back to kvm_flush_remote_tlbs.
This changes the behavior of many functions that indirectly use
slot_handle_level_range, iff the range based flushes are enabled. The
only potential problem I see with this is that kvm->tlbs_dirty will be
cleared less often, however the only caller of slot_handle_level_range that
checks tlbs_dirty is kvm_mmu_notifier_invalidate_range_start which
checks it and does a kvm_flush_remote_tlbs after calling
kvm_unmap_hva_range anyway.
Tested: Ran all kvm-unit-tests on a Intel Haswell machine with and
without this patch. The patch introduced no new failures.
Signed-off-by: Ben Gardon <bgardon@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[3] Neither <linux/kvm_para.h> nor <asm/kvm_para.h> is exported
csky, nds32, riscv
This does not match to the actual KVM support. At least, [2] is
half-baked.
Nor do arch maintainers look like they care about this. For example,
commit 0add53713b1c ("microblaze: Add missing kvm_para.h to Kbuild")
exported <asm/kvm_para.h> to user-space in order to fix an in-kernel
build error.
We have two ways to make this consistent:
[A] export both <linux/kvm_para.h> and <asm/kvm_para.h> for all
architectures, irrespective of the KVM support
[B] Match the header export of <linux/kvm_para.h> and <asm/kvm_para.h>
to the KVM support
My first attempt was [A] because the code looks cleaner, but Paolo
suggested [B].
So, this commit goes with [B].
For most architectures, <asm/kvm_para.h> was moved to the kernel-space.
I changed include/uapi/linux/Kbuild so that it checks generated
asm/kvm_para.h as well as check-in ones.
After this commit, there will be two groups:
[1] Both <linux/kvm_para.h> and <asm/kvm_para.h> are exported
arm, arm64, mips, powerpc, s390, x86
[2] Neither <linux/kvm_para.h> nor <asm/kvm_para.h> is exported
Wei Yang [Thu, 27 Sep 2018 00:31:26 +0000 (08:31 +0800)]
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
* nr_mmu_pages would be non-zero only if kvm->arch.n_requested_mmu_pages is
non-zero.
* nr_mmu_pages is always non-zero, since kvm_mmu_calculate_mmu_pages()
never return zero.
Based on these two reasons, we can merge the two *if* clause and use the
return value from kvm_mmu_calculate_mmu_pages() directly. This simplify
the code and also eliminate the possibility for reader to believe
nr_mmu_pages would be zero.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Singh, Brijesh [Fri, 15 Feb 2019 17:24:12 +0000 (17:24 +0000)]
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
Errata#1096:
On a nested data page fault when CR.SMAP=1 and the guest data read
generates a SMAP violation, GuestInstrBytes field of the VMCB on a
VMEXIT will incorrectly return 0h instead the correct guest
instruction bytes .
Recommend Workaround:
To determine what instruction the guest was executing the hypervisor
will have to decode the instruction at the instruction pointer.
The recommended workaround can not be implemented for the SEV
guest because guest memory is encrypted with the guest specific key,
and instruction decoder will not be able to decode the instruction
bytes. If we hit this errata in the SEV guest then log the message
and request a guest shutdown.
Reported-by: Venkatesh Srinivas <venkateshs@google.com> Cc: Jim Mattson <jmattson@google.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Joerg Roedel <joro@8bytes.org> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: Reject device ioctls from processes other than the VM's creator
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API") Cc: <stable@vger.kernel.org> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
Per Paolo[1], instantiating multiple VMs in a single process is legal;
but this conflicts with KVM's API documentation, which states:
The only supported use is one virtual machine per process, and one
vcpu per thread.
However, an earlier section in the documentation states:
Only run VM ioctls from the same process (address space) that was used
to create the VM.
and:
Only run vcpu ioctls from the same thread that was used to create the
vcpu.
This suggests that the conflicting documentation is simply an incorrect
ordering of of words, i.e. what's really meant is that a virtual machine
can't be shared across multiple processes and a vCPU can't be shared
across multiple threads.
Tweak the blurb on issuing ioctls to use a more assertive tone, and
rewrite the "supported use" sentence to reference said blurb instead of
poorly restating it in different terms.
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
The cr4_pae flag is a bit of a misnomer, its purpose is really to track
whether the guest PTE that is being shadowed is a 4-byte entry or an
8-byte entry. Prior to supporting nested EPT, the size of the gpte was
reflected purely by CR4.PAE. KVM fudged things a bit for direct sptes,
but it was mostly harmless since the size of the gpte never mattered.
Now that a spte may be tracking an indirect EPT entry, relying on
CR4.PAE is wrong and ill-named.
For direct shadow pages, force the gpte_size to '1' as they are always
8-byte entries; EPT entries can only be 8-bytes and KVM always uses
8-byte entries for NPT and its identity map (when running with EPT but
not unrestricted guest).
Likewise, nested EPT entries are always 8-bytes. Nested EPT presents a
unique scenario as the size of the entries are not dictated by CR4.PAE,
but neither is the shadow page a direct map. To handle this scenario,
set cr0_wp=1 and smap_andnot_wp=1, an otherwise impossible combination,
to denote a nested EPT shadow page. Use the information to avoid
incorrectly zapping an unsync'd indirect page in __kvm_sync_page().
Providing a consistent and accurate gpte_size fixes a bug reported by
Vitaly where fast_cr3_switch() always fails when switching from L2 to
L1 as kvm_mmu_get_page() would force role.cr4_pae=0 for direct pages,
whereas kvm_calc_mmu_role_common() would set it according to CR4.PAE.
Fixes: 7dcd575520082 ("x86/kvm/mmu: check if tdp/shadow MMU reconfiguration is needed") Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com> Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
Explicitly zero out quadrant and invalid instead of inheriting them from
the root_mmu. Functionally, this patch is a nop as we (should) never
set quadrant for a direct mapped (EPT) root_mmu and nested EPT is only
allowed if EPT is used for L1, and the root_mmu will never be invalid at
this point.
Explicitly setting flags sets the stage for repurposing the legacy
paging bits in role, e.g. nxe, cr0_wp, and sm{a,e}p_andnot_wp, at which
point 'smm' would be the only flag to be inherited from root_mmu.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andrey Smirnov [Tue, 26 Mar 2019 06:32:09 +0000 (23:32 -0700)]
gpio: of: Check for "spi-cs-high" in child instead of parent node
"spi-cs-high" is going to be specified in child node of an SPI
controller's representing attached SPI device, so change the code to
look for it there, instead of checking parent node.
Andrey Smirnov [Tue, 26 Mar 2019 06:32:08 +0000 (23:32 -0700)]
gpio: of: Check propname before applying "cs-gpios" quirks
SPI GPIO device has more than just "cs-gpio" property in its node and
would request those GPIOs as a part of its initialization. To avoid
applying CS-specific quirk to all of them add a check to make sure
that propname is "cs-gpios".
Jann Horn [Thu, 28 Mar 2019 15:49:48 +0000 (16:49 +0100)]
x86/cpufeature: Fix __percpu annotation in this_cpu_has()
&cpu_info.x86_capability is __percpu, and the second argument of
x86_this_cpu_test_bit() is expected to be __percpu. Don't cast the
__percpu away and then implicitly add it again. This gets rid of 106
lines of sparse warnings with the kernel config I'm using.
David Howells [Wed, 27 Mar 2019 22:48:02 +0000 (22:48 +0000)]
afs: Fix StoreData op marshalling
The marshalling of AFS.StoreData, AFS.StoreData64 and YFS.StoreData64 calls
generated by ->setattr() ops for the purpose of expanding a file is
incorrect due to older documentation incorrectly describing the way the RPC
'FileLength' parameter is meant to work.
The older documentation says that this is the length the file is meant to
end up at the end of the operation; however, it was never implemented this
way in any of the servers, but rather the file is truncated down to this
before the write operation is effected, and never expanded to it (and,
indeed, it was renamed to 'TruncPos' in 2014).
Fix this by setting the position parameter to the new file length and doing
a zero-lengh write there.
The bug causes Xwayland to SIGBUS due to unexpected non-expansion of a file
it then mmaps. This can be tested by giving the following test program a
filename in an AFS directory:
Linus Torvalds [Thu, 28 Mar 2019 15:35:32 +0000 (08:35 -0700)]
Merge tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Improvements and bug fixes for 5.1-rc2:
- Fix early free of the channel program in vfio
- On AP device removal make sure that all messages are flushed with
the driver still attached that queued the message
- Limit brk randomization to 32MB to reduce the chance that the heap
of ld.so is placed after the main stack
- Add a rolling average for the steal time of a CPU, this will be
needed for KVM to decide when to do busy waiting
- Fix a warning in the CPU-MF code
- Add a notification handler for AP configuration change to react
faster to new AP devices"
* tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cpumf: Fix warning from check_processor_id
zcrypt: handle AP Info notification from CHSC SEI command
vfio: ccw: only free cp on final interrupt
s390/vtime: steal time exponential moving average
s390/zcrypt: revisit ap device remove procedure
s390: limit brk randomization to 32MB
Linus Torvalds [Thu, 28 Mar 2019 15:23:45 +0000 (08:23 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A couple of minor fixes only for now
- fix for incorrect DMA channels on Renesas R-Car
- Broadcom bcm2835 error handling fixes
- Kconfig dependency fixes for bcm2835 and davinci
- CPU idle wakeup fix for i.MX6
- MMC regression on Tegra186
- fix incorrect phy settings on one imx board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186
ARM: dts: nomadik: Fix polarity of SPI CS
ARM: davinci: fix build failure with allnoconfig
ARM: imx_v4_v5_defconfig: enable PWM driver
ARM: imx_v6_v7_defconfig: continue compiling the pwm driver
ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch
ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi
ARM: dts: imx6ull: Use the correct style for SPDX License Identifier
ARM: dts: pfla02: increase phy reset duration
ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
ARM: imx51: fix a leaked reference by adding missing of_node_put
ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port
arm64: bcm2835: Add missing dependency on MFD_CORE.
ARM: dts: bcm283x: Fix hdmi hpd gpio pull
soc: bcm: bcm2835-pm: Fix error paths of initialization.
soc: bcm: bcm2835-pm: Fix PM_IMAGE_PERI power domain support.
arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels
Fredrik Noring [Wed, 27 Mar 2019 18:12:50 +0000 (19:12 +0100)]
kbuild: modversions: Fix relative CRC byte order interpretation
Fix commit 56067812d5b0 ("kbuild: modversions: add infrastructure for
emitting relative CRCs") where CRCs are interpreted in host byte order
rather than proper kernel byte order. The bug is conditional on
CONFIG_MODULE_REL_CRCS.
For example, when loading a BE module into a BE kernel compiled with a LE
system, the error "disagrees about version of symbol module_layout" is
produced. A message such as "Found checksum D7FA6856 vs module 5668FAD7"
will be given with debug enabled, which indicates an obvious endian
problem within __kcrctab within the kernel image.
The general solution is to use the macro TO_NATIVE, as is done in
similar cases throughout modpost.c. With this correction it has been
verified that a BE kernel compiled with a LE system accepts BE modules.
This change has also been verified with a LE kernel compiled with a LE
system, in which case TO_NATIVE returns its value unmodified since the
byte orders match. This is by far the common case.
Fixes: 56067812d5b0 ("kbuild: modversions: add infrastructure for emitting relative CRCs") Signed-off-by: Fredrik Noring <noring@nocrew.org> Cc: stable@vger.kernel.org Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Joe Lawrence [Tue, 26 Mar 2019 14:50:28 +0000 (10:50 -0400)]
kbuild: strip whitespace in cmd_record_mcount findstring
CC_FLAGS_FTRACE may contain trailing whitespace that interferes with
findstring.
For example, commit 6977f95e63b9 ("powerpc: avoid -mno-sched-epilog on
GCC 4.9 and newer") introduced a change such that on my ppc64le box,
CC_FLAGS_FTRACE="-pg -mprofile-kernel ". (Note the trailing space.)
When cmd_record_mcount is now invoked, findstring fails as the ftrace
flags were found at very end of _c_flags, without the trailing space.
_c_flags=" ... -pg -mprofile-kernel"
CC_FLAGS_FTRACE="-pg -mprofile-kernel "
^
findstring is looking for this extra space
Remove the redundant whitespaces from CC_FLAGS_FTRACE in
cmd_record_mcount to avoid this problem.
[masahiro.yamada: This issue only happens in the released versions
of GNU Make. CC_FLAGS_FTRACE will not contain the trailing space if
you use the latest GNU Make, which contains commit b90fabc8d6f3
("* NEWS: Do not insert a space during '+=' if the value is empty.") ]
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> (refactoring) Fixes: 6977f95e63b9 ("powerpc: avoid -mno-sched-epilog on GCC 4.9 and newer"). Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 26 Mar 2019 04:26:58 +0000 (13:26 +0900)]
kbuild: do not overwrite .gitignore in output directory
Commit 3a51ff344204 ("kbuild: gitignore output directory") seemed to
bother people who version-control output directories.
Andre Przywara says:
"Unfortunately this breaks my setup, because I keep a totally separate
git repository in my build directories to track (various versions of)
.config. So .gitignore there is carefully crafted to ignore most build
artefacts, but not .config, for instance."
Link: https://lkml.org/lkml/2019/3/22/1819 Reported-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Masahiro Yamada [Tue, 26 Mar 2019 04:02:19 +0000 (13:02 +0900)]
kbuild: skip parsing pre sub-make code for recursion
When Make recurses to the top Makefile with sub-make-done unset,
the code block surrounded by 'ifneq ($(sub-make-done),1) ... endif'
is parsed multiple times. This happens for in-tree building of
include/config/auto.conf, *-pkg, etc. with GNU Make 4.x.
This is a slight regression by commit 688931a5ad4e ("kbuild: skip
sub-make for in-tree build with GNU Make 4.x") in terms of performance
since that code block contains one $(shell ...) invocation.
Fix it by exporting the variable irrespective of sub-make being run.
I renamed it because GNU Make cannot properly export variables
containing hyphens. This is probably a bug of GNU Make, and the issue
in Kbuild had already been reported by commit 2bfbe7881ee0 ("kbuild:
Do not use hyphen in exported variable name").
GT VEBOX DISABLE is only 4 bits wide but it was using a 8 bits wide
mask, the remaning reserved bits is set to 0 causing 4 more
nonexistent VEBOX engines being detected as enabled, triggering the
BUG_ON() because of mismatch between vebox_mask and newly added
VEBOX_MASK().
BSpec: 20680 Fixes: 26376a7e74d2 ("drm/i915/icl: Check for fused-off VDBOX and VEBOX instances") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190326230223.26336-1-jose.souza@intel.com
(cherry picked from commit 547fcf9b1c608cf5c43c156a8773a94c6a38dc44) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ralph Campbell [Tue, 26 Mar 2019 00:18:17 +0000 (17:18 -0700)]
x86/mm: Don't exceed the valid physical address space
valid_phys_addr_range() is used to sanity check the physical address range
of an operation, e.g., access to /dev/mem. It uses __pa(high_memory)
internally.
If memory is populated at the end of the physical address space, then
__pa(high_memory) is outside of the physical address space because:
For the comparison in valid_phys_addr_range() this is not an issue, but if
CONFIG_DEBUG_VIRTUAL is enabled, __pa() maps to __phys_addr(), which
verifies that the resulting physical address is within the valid physical
address space of the CPU. So in the case that memory is populated at the
end of the physical address space, this is not true and triggers a
VIRTUAL_BUG_ON().
Use __pa(high_memory - 1) to prevent the conversion from going beyond
the end of valid physical addresses.
Fixes: be62a3204406 ("x86/mm: Limit mmap() of /dev/mem to valid physical addresses") Signed-off-by: Ralph Campbell <rcampbell@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Craig Bergstrom <craigb@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sander Eikelenboom <linux@eikelenboom.it> Cc: Sean Young <sean@mess.org> Link: https://lkml.kernel.org/r/20190326001817.15413-2-rcampbell@nvidia.com
Daniel Borkmann [Mon, 25 Mar 2019 13:56:20 +0000 (14:56 +0100)]
x86/retpolines: Disable switch jump tables when retpolines are enabled
Commit ce02ef06fcf7 ("x86, retpolines: Raise limit for generating indirect
calls from switch-case") raised the limit under retpolines to 20 switch
cases where gcc would only then start to emit jump tables, and therefore
effectively disabling the emission of slow indirect calls in this area.
After this has been brought to attention to gcc folks [0], Martin Liska
has then fixed gcc to align with clang by avoiding to generate switch jump
tables entirely under retpolines. This is taking effect in gcc starting
from stable version 8.4.0. Given kernel supports compilation with older
versions of gcc where the fix is not being available or backported anymore,
we need to keep the extra KBUILD_CFLAGS around for some time and generally
set the -fno-jump-tables to align with what more recent gcc is doing
automatically today.
More than 20 switch cases are not expected to be fast-path critical, but
it would still be good to align with gcc behavior for versions < 8.4.0 in
order to have consistency across supported gcc versions. vmlinux size is
slightly growing by 0.27% for older gcc. This flag is only set to work
around affected gcc, no change for clang.
Thomas Gleixner [Tue, 26 Mar 2019 16:36:06 +0000 (17:36 +0100)]
x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
The SMT disable 'nosmt' command line argument is not working properly when
CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are
required to be brought up due to the MCE issues, cannot work. The CPUs are
then kept in a half dead state.
As the 'nosmt' functionality has become popular due to the speculative
hardware vulnerabilities, the half torn down state is not a proper solution
to the problem.
Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is
possible.
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.598166056@linutronix.de
Thomas Gleixner [Tue, 26 Mar 2019 16:36:05 +0000 (17:36 +0100)]
cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
Tianyu reported a crash in a CPU hotplug teardown callback when booting a
kernel which has CONFIG_HOTPLUG_CPU disabled with the 'nosmt' boot
parameter.
It turns out that the SMP=y CONFIG_HOTPLUG_CPU=n case has been broken
forever in case that a bringup callback fails. Unfortunately this issue was
not recognized when the CPU hotplug code was reworked, so the shortcoming
just stayed in place.
When a bringup callback fails, the CPU hotplug code rolls back the
operation and takes the CPU offline.
The 'nosmt' command line argument uses a bringup failure to abort the
bringup of SMT sibling CPUs. This partial bringup is required due to the
MCE misdesign on Intel CPUs.
With CONFIG_HOTPLUG_CPU=y the rollback works perfectly fine, but
CONFIG_HOTPLUG_CPU=n lacks essential mechanisms to exercise the low level
teardown of a CPU including the synchronizations in various facilities like
RCU, NOHZ and others.
As a consequence the teardown callbacks which must be executed on the
outgoing CPU within stop machine with interrupts disabled are executed on
the control CPU in interrupt enabled and preemptible context causing the
kernel to crash and burn. The pre state machine code has a different
failure mode which is more subtle and resulting in a less obvious use after
free crash because the control side frees resources which are still in use
by the undead CPU.
But this is not a x86 only problem. Any architecture which supports the
SMP=y HOTPLUG_CPU=n combination suffers from the same issue. It's just less
likely to be triggered because in 99.99999% of the cases all bringup
callbacks succeed.
The easy solution of making HOTPLUG_CPU mandatory for SMP is not working on
all architectures as the following architectures have either no hotplug
support at all or not all subarchitectures support it:
Crashing the kernel in such a situation is not an acceptable state
either.
Implement a minimal rollback variant by limiting the teardown to the point
where all regular teardown callbacks have been invoked and leave the CPU in
the 'dead' idle state. This has the following consequences:
- the CPU is brought down to the point where the stop_machine takedown
would happen.
- the CPU stays there forever and is idle
- The CPU is cleared in the CPU active mask, but not in the CPU online
mask which is a legit state.
- Interrupts are not forced away from the CPU
- All facilities which only look at online mask would still see it, but
that is the case during normal hotplug/unplug operations as well. It's
just a (way) longer time frame.
This will expose issues, which haven't been exposed before or only seldom,
because now the normally transient state of being non active but online is
a permanent state. In testing this exposed already an issue vs. work queues
where the vmstat code schedules work on the almost dead CPU which ends up
in an unbound workqueue and triggers 'preemtible context' warnings. This is
not a problem of this change, it merily exposes an already existing issue.
Still this is better than crashing fully without a chance to debug it.
This is mainly thought as workaround for those architectures which do not
support HOTPLUG_CPU. All others should enforce HOTPLUG_CPU for SMP.
Fixes: 2e1a3483ce74 ("cpu/hotplug: Split out the state walk into functions") Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.503390616@linutronix.de
Thomas Gleixner [Tue, 26 Mar 2019 21:51:02 +0000 (22:51 +0100)]
watchdog: Respect watchdog cpumask on CPU hotplug
The rework of the watchdog core to use cpu_stop_work broke the watchdog
cpumask on CPU hotplug.
The watchdog_enable/disable() functions are now called unconditionally from
the hotplug callback, i.e. even on CPUs which are not in the watchdog
cpumask. As a consequence the watchdog can become unstoppable.
Only invoke them when the plugged CPU is in the watchdog cpumask.
Fixes: 9cf57731b63e ("watchdog/softlockup: Replace "watchdog/%u" threads with cpu_stop_work") Reported-by: Maxime Coquelin <maxime.coquelin@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Don Zickus <dzickus@redhat.com> Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903262245490.1789@nanos.tec.linutronix.de
Thomas Richter [Mon, 18 Mar 2019 14:50:27 +0000 (15:50 +0100)]
s390/cpumf: Fix warning from check_processor_id
Function __hw_perf_event_init() used a CPU variable without
ensuring CPU preemption has been disabled. This caused the
following warning in the kernel log:
The variable is now accessed in proper context. Use
get_cpu_var()/put_cpu_var() pair to disable
preemption during access.
As the hardware authorization settings apply to all CPUs, it
does not matter which CPU is used to check the authorization setting.
Remove the event->count assignment. It is not needed as function
perf_event_alloc() allocates memory for the event with kzalloc() and
thus count is already set to zero.
Fixes: fe5908bccc56 ("s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Tyrel Datwyler [Wed, 20 Mar 2019 19:56:54 +0000 (14:56 -0500)]
scsi: ibmvfc: Clean up transport events
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tyrel Datwyler [Wed, 20 Mar 2019 19:56:53 +0000 (14:56 -0500)]
scsi: ibmvfc: Byte swap status and error codes when logging
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tyrel Datwyler [Wed, 20 Mar 2019 19:56:52 +0000 (14:56 -0500)]
scsi: ibmvfc: Add failed PRLI to cmd_status lookup array
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tyrel Datwyler [Wed, 20 Mar 2019 19:56:51 +0000 (14:56 -0500)]
scsi: ibmvfc: Remove "failed" from logged errors
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Tue, 26 Mar 2019 13:37:00 +0000 (14:37 +0100)]
scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Tue, 26 Mar 2019 13:36:59 +0000 (14:36 +0100)]
scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Tue, 26 Mar 2019 13:36:58 +0000 (14:36 +0100)]
scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Cc: <stable@vger.kernel.org> #2.6.32+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: sd: Quiesce warning if device does not report optimal I/O size
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size") Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Reported-by: Hussam Al-Tayeb <ht990332@gmx.com> Tested-by: Hussam Al-Tayeb <ht990332@gmx.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 25 Mar 2019 17:01:46 +0000 (10:01 -0700)]
scsi: sd: Fix a race between closing an sd device and sd I/O
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Jason Yan <yanaijie@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reported-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
Chen Zhou [Wed, 27 Mar 2019 13:51:16 +0000 (21:51 +0800)]
arm64: replace memblock_alloc_low with memblock_alloc
If we use "crashkernel=Y[@X]" and the start address is above 4G,
the arm64 kdump capture kernel may call memblock_alloc_low() failure
in request_standard_resources(). Replacing memblock_alloc_low() with
memblock_alloc().
Al Viro [Tue, 26 Mar 2019 01:38:58 +0000 (01:38 +0000)]
ceph: fix use-after-free on symlink traversal
free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Hans de Goede [Fri, 22 Mar 2019 08:19:34 +0000 (09:19 +0100)]
virt: vbox: Implement passing requestor info to the host for VirtualBox 6.0.x
VirtualBox 6.0.x has a new feature where the guest kernel driver passes
info about the origin of the request (e.g. userspace or kernelspace) to
the hypervisor.
If we do not pass this information then when running the 6.0.x userspace
guest-additions tools on a 6.0.x host, some requests will get denied
with a VERR_VERSION_MISMATCH error, breaking vboxservice.service and
the mounting of shared folders marked to be auto-mounted.
This commit implements passing the requestor info to the host, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabien Dessenne [Thu, 21 Mar 2019 15:43:26 +0000 (16:43 +0100)]
tty: fix NULL pointer issue when tty_port ops is not set
Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Romain Izard [Fri, 22 Mar 2019 15:53:02 +0000 (16:53 +0100)]
usb: cdc-acm: fix race during wakeup blocking TX traffic
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
Wolfram Sang [Thu, 21 Mar 2019 23:04:23 +0000 (00:04 +0100)]
i2c: wmt: make bindings file name match the driver
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Wolfram Sang [Thu, 21 Mar 2019 23:04:22 +0000 (00:04 +0100)]
i2c: sun6i-p2wi: make bindings file name match the driver
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Wolfram Sang [Thu, 21 Mar 2019 23:04:21 +0000 (00:04 +0100)]
i2c: stu300: make bindings file name match the driver
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Wolfram Sang [Thu, 21 Mar 2019 23:04:20 +0000 (00:04 +0100)]
i2c: mt65xx: make bindings file name match the driver
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Wolfram Sang [Thu, 21 Mar 2019 23:04:19 +0000 (00:04 +0100)]
i2c: iop3xx: make bindings file name match the driver
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
The debugfs read callback must advance ppos or users using read() on
the file descriptor will never get the EOL. This wasn't spotted before
as I was using busybox cat for testing which uses sendfile() internally
and only noticed it now when switched to cat from coreutils.
We only hit unregister_allocated_timer() if the argument to
aspeed_gpio_set_config() is 0, but we can't be calling through
gpiod_set_debounce() from gpio_keys_probe() unless the gpio-keys button has a
non-zero debounce interval.
Commit 6581eaf0e890 ("gpio: use new gpio_set_config() helper in more places")
spreads the use of gpio_set_config() to the debounce and transitory
state configuration paths. The implementation of gpio_set_config() is:
Here it packs its own config value with a fixed argument of 0; this is
incorrect behaviour for implementing the debounce and transitory functions, and
the debounce and transitory gpio_set_config() call-sites now have an undetected
type mismatch as they both already pack their own config parameter (i.e. what
gets passed is not an `enum pin_config_param`). Indeed this can be seen in the
small diff for 6581eaf0e890:
Revert commit 6581eaf0e890 ("gpio: use new gpio_set_config() helper in
more places") to restore correct behaviour for gpiod_set_debounce() and
gpiod_set_transitory().
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
In cpu_to_drc_index() in the case when FW_FEATURE_DRC_INFO is absent,
we currently use of_read_property() to obtain the pointer to the array
corresponding to the property "ibm,drc-indexes". The elements of this
array are of type __be32, but are accessed without any conversion to
the OS-endianness, which is buggy on a Little Endian OS.
Fix this by using of_property_read_u32_index() accessor function to
safely read the elements of the array.
Fixes: e83636ac3334 ("pseries/drc-info: Search DRC properties for CPU indexes") Cc: stable@vger.kernel.org # v4.16+ Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[mpe: Make the WARN_ON a WARN_ON_ONCE so it's not retriggerable] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Tue, 26 Mar 2019 21:25:48 +0000 (14:25 -0700)]
Merge tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
- fix mount/umount race in nlmclnt.
- NFSv4.1 don't free interrupted slot on open
Bugfixes:
- Don't let RPC_SOFTCONN tasks time out if the transport is connected
- Fix a typo in nfs_init_timeout_values()
- Fix layoutstats handling during read failovers
- fix uninitialized variable warning"
* tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: fix uninitialized variable warning
pNFS/flexfiles: Fix layoutstats handling during read failovers
NFS: Fix a typo in nfs_init_timeout_values()
SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected
NFSv4.1 don't free interrupted slot on open
NFS: fix mount/umount race in nlmclnt.
NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
Alakesh Haloi [Tue, 26 Mar 2019 02:00:01 +0000 (02:00 +0000)]
SUNRPC: fix uninitialized variable warning
Avoid following compiler warning on uninitialized variable
net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’:
net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return read;
^~~~
net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return ret < 0 ? ret : read;
~~~~~~~~~~~~~~^~~~~~
Rafał Miłecki [Thu, 28 Feb 2019 21:57:33 +0000 (22:57 +0100)]
leds: trigger: netdev: fix refcnt leak on interface rename
Renaming a netdev-trigger-tracked interface was resulting in an
unbalanced dev_hold().
Example:
> iw phy phy0 interface add foo type __ap
> echo netdev > trigger
> echo foo > device_name
> ip link set foo name bar
> iw dev bar del
[ 237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1
Above problem was caused by trigger checking a dev->name which obviously
changes after renaming an interface. It meant missing all further events
including the NETDEV_UNREGISTER which is required for calling dev_put().
This change fixes that by:
1) Comparing device struct *address* for notification-filtering purposes
2) Dropping unneeded NETDEV_CHANGENAME code (no behavior change)
Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Ioana Ciornei [Mon, 25 Mar 2019 13:06:22 +0000 (13:06 +0000)]
dpaa2-eth: fix race condition with bql frame accounting
It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.
This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.
Fixes: 569dac6a5a0d ("dpaa2-eth: bql support") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 25 Mar 2019 12:49:16 +0000 (13:49 +0100)]
chelsio: use BUG() instead of BUG_ON(1)
clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
# define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x)))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
return buf_size;
^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
BUG_ON(1);
^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^
drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
int buf_size;
^
= 0
Use BUG() here to create simpler code that clang understands
correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 23 Mar 2019 23:21:03 +0000 (00:21 +0100)]
net: devlink: skip info_get op call if it is not defined in dumpit
In dumpit, unlike doit, the check for info_get op being defined
is missing. Add it and avoid null pointer dereference in case driver
does not define this op.
Fixes: f9cf22882c60 ("devlink: add device information API") Reported-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 23 Mar 2019 22:18:46 +0000 (00:18 +0200)]
net: phy: bcm54xx: Encode link speed and activity into LEDs
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It was caused by the netns freed without deleting the discoverer timer,
while later on the netns would be accessed in the timer handler.
The timer should have been deleted by tipc_net_stop() when cleaning up a
netns. However, tipc has been able to enable a bearer and start d->timer
without the local node_addr set since Commit 52dfae5c85a4 ("tipc: obtain
node identity from interface by default"), which caused the timer not to
be deleted in tipc_net_stop() then.
So fix it in tipc_net_stop() by changing to check local node_id instead
of local node_addr, as Jon suggested.
While at it, remove the calling of tipc_nametbl_withdraw() there, since
tipc_nametbl_stop() will take of the nametbl's freeing after.
Fixes: 52dfae5c85a4 ("tipc: obtain node identity from interface by default") Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: dsa: qca8k: support internal mdio-bus
This patch updates the qca8k's binding to document to the
approach for using the internal mdio-bus of the supported
qca8k switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In the example, the phy at phy@0 is clashing with
the switch0@0 at the same address. Usually, the switches
are accessible through pseudo PHYs which in case of the
qca8k are located at 0x10 - 0x18.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tag 'for-5.1-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix assertion failure on fsync with NO_HOLES enabled
btrfs: Avoid possible qgroup_rsv_size overflow in btrfs_calculate_inode_block_rsv_size
btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks
btrfs: raid56: properly unmap parity page in finish_parity_scrub()
btrfs: don't report readahead errors and don't update statistics
Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes
btrfs: remove WARN_ON in log_dir_items
Btrfs: fix incorrect file size after shrinking truncate and fsync
Linus Torvalds [Tue, 26 Mar 2019 17:21:55 +0000 (10:21 -0700)]
Merge tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three small fixes:
- A fix to a double free in the histogram code
- Uninitialized variable fix
- Use NULL instead of zero fix and spelling fixes"
* tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix warning using plain integer as NULL & spelling corrections
tracing: initialize variable in create_dyn_event()
tracing: Remove unnecessary var_ref destroy in track_data_destroy()
Brian Foster [Tue, 26 Mar 2019 00:01:45 +0000 (17:01 -0700)]
xfs: serialize unaligned dio writes against all other dio writes
XFS applies more strict serialization constraints to unaligned
direct writes to accommodate things like direct I/O layer zeroing,
unwritten extent conversion, etc. Unaligned submissions acquire the
exclusive iolock and wait for in-flight dio to complete to ensure
multiple submissions do not race on the same block and cause data
corruption.
This generally works in the case of an aligned dio followed by an
unaligned dio, but the serialization is lost if I/Os occur in the
opposite order. If an unaligned write is submitted first and
immediately followed by an overlapping, aligned write, the latter
submits without the typical unaligned serialization barriers because
there is no indication of an unaligned dio still in-flight. This can
lead to unpredictable results.
To provide proper unaligned dio serialization, require that such
direct writes are always the only dio allowed in-flight at one time
for a particular inode. We already acquire the exclusive iolock and
drain pending dio before submitting the unaligned dio. Wait once
more after the dio submission to hold the iolock across the I/O and
prevent further submissions until the unaligned I/O completes. This
is heavy handed, but consistent with the current pre-submission
serialization for unaligned direct writes.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Hariprasad Kelam [Sat, 23 Mar 2019 18:35:23 +0000 (00:05 +0530)]
ftrace: Fix warning using plain integer as NULL & spelling corrections
Changed 0 --> NULL to avoid sparse warning
Corrected spelling mistakes reported by checkpatch.pl
Sparse warning below:
sudo make C=2 CF=-D__CHECK_ENDIAN__ M=kernel/trace
CHECK kernel/trace/ftrace.c
kernel/trace/ftrace.c:3007:24: warning: Using plain integer as NULL pointer
kernel/trace/ftrace.c:4758:37: warning: Using plain integer as NULL pointer
Tom Zanussi [Wed, 20 Mar 2019 17:53:33 +0000 (12:53 -0500)]
tracing: Remove unnecessary var_ref destroy in track_data_destroy()
Commit 656fe2ba85e8 (tracing: Use hist trigger's var_ref array to
destroy var_refs) centralized the destruction of all the var_refs
in one place so that other code didn't have to do it.
The track_data_destroy() added later ignored that and also destroyed
the track_data var_ref, causing a double-free error flagged by KASAN.
==================================================================
BUG: KASAN: use-after-free in destroy_hist_field+0x30/0x70
Read of size 8 at addr ffff888086df2210 by task bash/1694
Merge tag 'misc-habanalabs-fixes-2019-03-26' of git://people.freedesktop.org/~gabbayo/linux into char-misc-next:
Oded writes:
The following bug fixes are included in this tag:
- Fix host crash upon resume after suspend
- Fix MMU related bugs which result in user's jobs getting stuck
- Fix race between user context cleanup and hard-reset which results in
host crash
- Fix sparse warning
* tag 'misc-habanalabs-fixes-2019-03-26' of git://people.freedesktop.org/~gabbayo/linux: (265 commits)
habanalabs: cast to expected type
habanalabs: prevent host crash during suspend/resume
habanalabs: perform accounting for active CS
habanalabs: fix mapping with page size bigger than 4KB
habanalabs: complete user context cleanup before hard reset
habanalabs: fix bug when mapping very large memory area
habanalabs: fix MMU number of pages calculation
Linux 5.1-rc2
clocksource/drivers/clps711x: Remove board support
ext4: prohibit fstrim in norecovery mode
ext4: cleanup bh release code in ext4_ind_remove_space()
ext4: brelse all indirect buffer in ext4_ind_remove_space()
genirq: Mark expected switch case fall-through
clocksource/drivers/riscv: Fix clocksource mask
x86/gart: Exclude GART aperture from kcore
cifs: update internal module version number
SMB3: Fix SMB3.1.1 guest mounts to Samba
cifs: Fix slab-out-of-bounds when tracing SMB tcon
cifs: allow guest mounts to work for smb3.11
fix incorrect error code mapping for OBJECTID_NOT_FOUND
...
projects / linux.git / log