Heikki Krogerus [Tue, 23 Apr 2019 14:21:48 +0000 (17:21 +0300)]
usb: typec: ucsi: Preliminary support for alternate modes
With UCSI the alternate modes, just like everything else
related to USB Type-C connectors, are handled in firmware.
The operating system can see the status and is allowed to
request certain things, for example entering and exiting the
modes, but the support for alternate modes is very limited
in UCSI. The feature is also optional, which means that even
when the platform supports alternate modes, the operating
system may not be even made aware of them.
UCSI does not support direct VDM reading or writing.
Instead, alternate modes can be entered and exited using a
single custom command which takes also an optional SVID
specific configuration value as parameter. That means every
supported alternate mode has to be handled separately in
UCSI driver.
This commit does not include support for any specific
alternate mode. The discovered alternate modes are now
registered, but binding a driver to an alternate mode will
not be possible until support for that alternate mode is
added to the UCSI driver.
usb: typec: ucsi: ccg: add firmware flashing support
CCGx has two copies of the firmware in addition to the bootloader.
If the device is running FW1, FW2 can be updated with the new version.
Dual firmware mode allows the CCG device to stay in a PD contract and
support USB PD and Type-C functionality while a firmware update is in
progress.
First we read the currently flashed firmware version of both
primary and secondary firmware and then compare it with
version of firmware file to determine if flashing is required.
Command framework is added to support sending commands to CCGx
controller. We wait for response after sending the command and then
read the response from RAB_RESPONSE register.
usb: usb251xb: Lock i2c-bus segment the hub resides
SMBus slave configuration is activated by CFG_SEL[1:0]=0x1 pins
state. This is the mode the hub is supposed to be to let this driver
work correctly. But a race condition might happen right after reset
is cleared due to CFG_SEL[0] pin being multiplexed with SMBus SCL
function. In case if the reset pin is handled by a i2c GPIO expander,
which is also placed at the same i2c-bus segment as the usb251x
SMB-interface connected to, then the hub reset clearance might
cause the CFG_SEL[0] being latched in unpredictable state. So
sometimes the hub configuration mode might be 0x1 (as expected),
but sometimes being 0x0, which doesn't imply to have the hub SMBus-slave
interface activated and consequently causes this driver failure.
In order to fix the problem we must make sure the GPIO-reset chip doesn't
reside the same i2c-bus segment as the SMBus-interface of the hub. If
it doesn't, we can safely block the segment for the time the reset is
cleared to prevent anyone generating a traffic at the i2c-bus SCL lane
connected to the CFG_SEL[0] pin. But if it does, nothing we can do, so
just return an error. If we locked the i2c-bus segment and tried to
communicate with the GPIO-expander, it would cause a deadlock. If we didn't
lock the i2c-bus segment, it would randomly cause the CFG_SEL[0] bit flip.
Merge tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (51 commits)
dt-bindings: phy-qcom-qmp: Tweak qcom,msm8998-qmp-ufs-phy
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-pcie-phy
phy: Add usb phy support for hi3660 Soc of Hisilicon
dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
scsi: phy: mediatek: fix typo in author's email address
phy: ocelot-serdes: Add support for SERDES6G muxing
phy: fsl-imx8mq-usb: add support for VBUS power control
dt-bindings: phy-imx8mq-usb: add optional vbus supply regulator
phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
phy: ti: am654-serdes: Support all clksel values
phy: ti: Add a new SERDES driver for TI's AM654x SoC
dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
phy: socionext: get optional clock by devm_clk_get_optional()
phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
phy: phy-mtk-tphy: get optional clock by devm_clk_get_optional()
phy: renesas: rcar-gen3-usb2: enable/disable independent irqs
phy: renesas: rcar-gen3-usb2: Use pdev's device pointer on dev_vdbg()
...
usb: mtu3: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so
the replacement doesn't change original purpose.
usb: chipidea: msm: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
Cc: Peter Chen <Peter.Chen@nxp.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Peter Chen <Peter.Chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: dwc2: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.
usb: misc: usb3503: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
And remove unnecessary stack variable clk.
usb: host: xhci-plat: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
usb: xhci-mtk: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so the
replacement doesn't change original purpose.
Hans de Goede [Tue, 16 Apr 2019 20:07:54 +0000 (22:07 +0200)]
usb: typec: fusb302: Revert "Resolve fixed power role contract setup"
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. But for single-role ports we've so far been
falling back to just calling tcpm_set_cc(). For some tcpc-s such as the
fusb302 this is not enough and no TCPM_CC_EVENT will be generated.
Commit ea3b4d5523bc ("usb: typec: fusb302: Resolve fixed power role
contract setup") fixed SRPs not working because of this by making the
fusb302 driver start connection detection on every tcpm_set_cc() call.
It turns out this breaks src->snk power-role swapping because during the
swap we first set the Cc pins to Rp, calling set_cc, and then send a PS_RDY
message. But the fusb302 cannot send PD messages while its toggling engine
is active, so sending the PS_RDY message fails.
Struct tcpc_dev now has a new start_srp_connection_detect callback and
fusb302.c now implements this. This callback gets called when we the
fusb302 needs to start connection detection, fixing fusb302 SRPs not
seeing connected devices.
This allows us to revert the changes to fusb302's set_cc implementation,
making it once again purely setup the Cc-s and matching disconnect
detection, fixing src->snk power-role swapping no longer working.
Note that since the code was refactored in between, codewise this is not a
straight forward revert. Functionality wise this is a straight revert and
the original functionality is fully restored.
Fixes: ea3b4d5523bc ("usb: typec: fusb302: Resolve fixed power role ...") Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 16 Apr 2019 20:07:53 +0000 (22:07 +0200)]
usb: typec: fusb302: Implement start_toggling for all port-types
When in single-role port mode, we must start single-role toggling to
get an interrupt when a device / cable gets plugged into the port.
This commit modifies the fusb302 start_toggling implementation to
start toggling for all port-types, so that connection-detection works
on single-role ports too.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...") Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 16 Apr 2019 20:07:52 +0000 (22:07 +0200)]
usb: typec: tcpm: Notify the tcpc to start connection-detection for SRPs
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...") Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Chen [Fri, 29 Mar 2019 04:13:57 +0000 (12:13 +0800)]
dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
This patch adds binding documentation for supporting the hi3660 usb
phy on boards like the HiKey960.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Binghui Wang <wangbinghui@hisilicon.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Yu Chen <chenyu56@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Colin Ian King [Wed, 20 Mar 2019 21:22:04 +0000 (21:22 +0000)]
scsi: phy: mediatek: fix typo in author's email address
There is a typo in the module author's email address. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Alan Stern [Tue, 16 Apr 2019 14:50:01 +0000 (10:50 -0400)]
USB: core: Don't unbind interfaces following device reset failure
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> CC: Bart Van Assche <bvanassche@acm.org> CC: Martin K. Petersen <martin.petersen@oracle.com> CC: Jacky Cao <Jacky.Cao@sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Gonzalez [Tue, 9 Apr 2019 12:48:22 +0000 (14:48 +0200)]
phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
Documentation for this PHY, and the proper configuration settings,
is *not* publicly available. Therefore the initialization sequence
is copied wholesale from downstream:
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: ti: Add a new SERDES driver for TI's AM654x SoC
Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 will be added later.
SERDES in am654x has three input clocks (left input, externel reference
clock and right input) and two output clocks (left output and right
output) in addition to a PLL mux clock which the SERDES uses for Clock
Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input clocks.
The right output can select between left input and external reference
clock while the left output can select between the right input and
external reference clock.
The driver has support to select PLL mux and left/right output mux as
specified in device tree.
[rogerq@ti.com: Fix boot lockup caused by accessing a structure member
(hw->init) allocated in stack of probe() and accessed in get_parent]
[rogerq@ti.com: Fix "Failed to find the parent" warnings] Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
AM654x has two SERDES instances. Each instance has three input clocks
(left input, externel reference clock and right input) and two output
clocks (left output and right output) in addition to a PLL mux clock
which the SERDES uses for Clock Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input clocks.
The right output can select between left input and external reference
clock while the left output can select between the right input and
external reference clock.
The left and right input reference clock of SERDES0 and SERDES1
respectively are connected to the SoC clock. In the case of two lane
SERDES personality card, the left input of SERDES1 is connected to
the right output of SERDES0 in a chained fashion.
See section "Reference Clock Distribution" of AM65x Sitara Processors
TRM (SPRUID7 – April 2018) for more details.
Add dt-binding documentation in order to represent all these different
configurations in device tree.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
PHY drivers may try to access PHY registers in the ->reset() callback.
Invoke phy_pm_runtime_get_sync() before invoking the ->reset() callback
so that the PHY drivers don't have to enable clocks by themselves before
accessing PHY registers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock
Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the previous code enabled/disabled the irqs both OHCI and EHCI,
it is possible to cause unexpected interruptions. To avoid this,
this patch creates multiple phy instances from phandle and
enables/disables independent irqs by the instances.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Biju Das [Wed, 10 Apr 2019 14:48:41 +0000 (15:48 +0100)]
phy: rcar-gen3-usb2: Add support for r8a77470
This patch adds support for r8a77470 (RZ/G1C). We can reuse this driver for
initializing timing/interrupt generation registers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Biju Das [Wed, 10 Apr 2019 14:48:39 +0000 (15:48 +0100)]
phy: renesas: phy-rcar-gen2: Add support for r8a77470
This patch adds support for RZ/G1C (r8a77470) SoC. RZ/G1C SoC has a
PLL register shared between hsusb0 and hsusb1. Compared to other RZ/G1
and R-Car Gen2/3, USB Host needs to deassert the pll reset.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-and-Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Biju Das [Wed, 10 Apr 2019 14:48:40 +0000 (15:48 +0100)]
dt-bindings: rcar-gen3-phy-usb2: Add r8a77470 support
Document RZ/G1C (R8A77470) SoC bindings.
For RZ/G1C, this driver is used to enable interrupt generation and
initializing timing registers which is part of phy_init code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Biju Das [Wed, 10 Apr 2019 14:48:38 +0000 (15:48 +0100)]
dt-bindings: phy: rcar-gen2: Add r8a77470 support
Add USB PHY support for r8a77470 SoC. Renesas RZ/G1C (R8A77470)
USB PHY is similar to the R-Car Gen2 family, but has the below
feature compared to other RZ/G1 and R-Car Gen2/3 SoCs
It has a shared pll reset for usbphy0/usbphy1 and this register
reside in usbphy0 block.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Roger Quadros [Fri, 22 Mar 2019 08:58:05 +0000 (10:58 +0200)]
phy: ti-pipe3: improve DPLL stability for SATA & USB
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
Colin Ian King [Tue, 19 Feb 2019 14:53:49 +0000 (14:53 +0000)]
phy: ti-pipe3: fix missing bit-wise or operator when assigning val
There seems to be a missing bit-wise or operator when setting val,
fix this by adding it in.
Fixes: 2796ceb0c18a ("phy: ti-pipe3: Update pcie phy settings") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Stanley Chu [Sat, 16 Mar 2019 05:04:46 +0000 (13:04 +0800)]
phy: mediatek: Add UFS M-PHY driver
Add UFS M-PHY driver on MediaTek chipsets.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
dt-bindings: phy: Add a new property drive-impedance-ohm for RK's emmc PHY
This patch documents the new proprty drive-impedance-ohm for
Rockchip's eMMC PHY node.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: rockchip-emmc: Allow to set drive impedance via DTS.
The rockchip-emmc PHY can be configured with different
drive impedance values. Currenlty a value of 50 Ohm is
hard coded into the driver.
This patch introduces the DTS property 'drive-impedance-ohm'
for the rockchip-emmc phy node, which uses the value from the DTS
to setup the drive impedance accordingly.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Evan Green [Thu, 21 Mar 2019 17:18:00 +0000 (10:18 -0700)]
phy: ufs-qcom: Refactor all init steps into phy_poweron
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Evan Green [Thu, 21 Mar 2019 17:17:58 +0000 (10:17 -0700)]
scsi: ufs: qcom: Expose the reset controller for PHY
Expose a reset controller that the phy will later use to control its
own PHY reset in the UFS controller. This will enable the combining
of PHY init functionality into a single function.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Evan Green [Thu, 21 Mar 2019 17:17:55 +0000 (10:17 -0700)]
dt-bindings: phy: qcom-ufs: Add resets property
Add a resets property to the PHY that represents the PHY reset
register in the UFS controller itself. This better describes the
complete specification of the PHY, and allows the PHY to perform
its initialization in a single function, rather than relying on
back-channel sequencing of initialization through the PHY framework.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Evan Green [Thu, 21 Mar 2019 17:17:54 +0000 (10:17 -0700)]
dt-bindings: phy-qcom-qmp: Add UFS PHY reset
Add a required reset to the SDM845 UFS phy to express the PHY reset
bit inside the UFS controller register space. Before this change, this
reset was not expressed in the DT, and the driver utilized two different
callbacks (phy_init and phy_poweron) to implement a two-phase
initialization procedure that involved deasserting this reset between
init and poweron. This abused the two callbacks and diluted their
purpose.
That scheme does not work as regulators cannot be turned off in
phy_poweroff because they were turned on in init, rather than poweron.
The net result is that regulators are left on in suspend that shouldn't
be.
This new scheme gives the UFS reset to the PHY, so that it can fully
initialize itself in a single callback. We can then turn regulators on
during poweron and off during poweroff.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Evan Green [Thu, 21 Mar 2019 17:17:53 +0000 (10:17 -0700)]
dt-bindings: ufs: Add #reset-cells for Qualcomm controllers
Enable Qualcomm UFS controllers to expose the PHY reset via a reset
controller.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Neil Armstrong [Mon, 25 Mar 2019 09:39:40 +0000 (10:39 +0100)]
phy: amlogic: add Amlogic G12A USB2 PHY Driver
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the Amlogic G12A Family USB3 + PCIE Combo PHY Bindings.
This PHY can provide exclusively USB3 or PCIE support on shared I/Os.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The PHY can work in host or peripheral modes depending on it's position.
Configuration of the mode is part of the USBCTRL registers which are
outside of the PHY registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Srinath Mannam [Tue, 19 Mar 2019 09:15:42 +0000 (14:45 +0530)]
dt-bindings: phy: Add Stingray USB PHY binding document
Add DT binding document for Stingray USB PHY.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
JC Kuo [Thu, 21 Feb 2019 15:46:34 +0000 (16:46 +0100)]
phy: tegra: xusb: Add Tegra186 support
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()] Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning] Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Thierry Reding [Thu, 21 Feb 2019 15:46:32 +0000 (16:46 +0100)]
phy: tegra: xusb: Parse dual-role mode property
The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.
Based on work by JC Kuo <jckuo@nvidia.com>.
Reviewed-by: JC Kuo <jckuo@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
JC Kuo [Thu, 21 Feb 2019 15:46:31 +0000 (16:46 +0100)]
phy: tegra: xusb: Skip single function lane programming
Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.
Signed-off-by: JC Kuo <jckuo@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Thierry Reding [Thu, 21 Feb 2019 15:46:30 +0000 (16:46 +0100)]
dt-bindings: phy: tegra: Add Tegra186 support
Extend the bindings to cover the set of features found in Tegra186. Note
that, technically, there are four more supplies connected to the XUSB
pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
the power sequencing requirements of Tegra186 require these to be under
the control of the PMIC.
Reviewed-by: JC Kuo <jckuo@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Alan Stern [Mon, 15 Apr 2019 17:19:25 +0000 (13:19 -0400)]
usb-storage: Set virt_boundary_mask to avoid SG overflows
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.
So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512. However, USB 3 has a bulk maxpacket
size of 1024. Since the xhci-hcd driver includes native SG support,
this hasn't mattered much. But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.
The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers. The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.
Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Seth Bollinger <Seth.Bollinger@digi.com> Tested-by: Seth Bollinger <Seth.Bollinger@digi.com> CC: Ming Lei <tom.leiming@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: hub: Remove returned value 'status' since never used
The returned value in status has never been used since
commit 4296c70a5ec3 ("USB/xHCI: Enable USB 3.0 hub remote wakeup.")
So remove 'status' completely.
Remove warning (W=1):
drivers/usb/core/hub.c:3671:8: warning: variable 'status' set but not used [-Wunused-but-set-variable]
JC Kuo [Mon, 1 Apr 2019 10:40:47 +0000 (12:40 +0200)]
usb: host: xhci-tegra: Add Tegra186 XUSB support
This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.
JC Kuo [Mon, 1 Apr 2019 10:40:46 +0000 (12:40 +0200)]
usb: host: xhci-tegra: Selectively program IPFS
Starting with Tegra186, the XUSB controller no longer has the IPFS
wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc
that can be used to declare the existence of the IPFS wrapper.
For the existing chips (i.e. Tegra124 and Tegra210), the new field is
set to true. A future patch adding support for Tegra186 will set it to
false.
Linus Torvalds [Sun, 31 Mar 2019 15:55:59 +0000 (08:55 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A collection of x86 and ARM bugfixes, and some improvements to
documentation.
On top of this, a cleanup of kvm_para.h headers, which were exported
by some architectures even though they not support KVM at all. This is
responsible for all the Kbuild changes in the diffstat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
KVM: doc: Document the life cycle of a VM and its resources
KVM: selftests: complete IO before migrating guest state
KVM: selftests: disable stack protector for all KVM tests
KVM: selftests: explicitly disable PIE for tests
KVM: selftests: assert on exit reason in CR4/cpuid sync test
KVM: x86: update %rip after emulating IO
x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
kvm: don't redefine flags as something else
kvm: mmu: Used range based flushing in slot_handle_level_range
KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
KVM: Reject device ioctls from processes other than the VM's creator
KVM: doc: Fix incorrect word ordering regarding supported use of APIs
KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
...
Linus Torvalds [Sun, 31 Mar 2019 15:37:04 +0000 (08:37 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Thomas Gleixner:
"Core libraries:
- Fix max perf_event_attr.precise_ip detection.
- Fix parser error for uncore event alias
- Fixup ordering of kernel maps after obtaining the main kernel map
address.
Intel PT:
- Fix TSC slip where A TSC packet can slip past MTC packets so that
the timestamp appears to go backwards.
- Fixes for exported-sql-viewer GUI conversion to python3.
ARM coresight:
- Fix the build by adding a missing case value for enumeration value
introduced in newer library, that now is the required one.
tool headers:
- Syncronize kernel headers with the kernel, getting new io_uring and
pidfd_send_signal syscalls so that 'perf trace' can handle them"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf pmu: Fix parser error for uncore event alias
perf scripts python: exported-sql-viewer.py: Fix python3 support
perf scripts python: exported-sql-viewer.py: Fix never-ending loop
perf machine: Update kernel map address and re-order properly
tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
tools headers uapi: Update drm/i915_drm.h
tools arch x86: Sync asm/cpufeatures.h with the kernel sources
tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
perf evsel: Fix max perf_event_attr.precise_ip detection
perf intel-pt: Fix TSC slip
perf cs-etm: Add missing case value
Linus Torvalds [Sun, 31 Mar 2019 15:22:12 +0000 (08:22 -0700)]
Merge branch 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug fixes from Thomas Gleixner:
"Two SMT/hotplug related fixes:
- Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
aborts. This is triggered with the 'nosmt' command line option, but
can happen by any abort condition. As the real unplug code is not
compiled in, prevent the fail by keeping the CPU in zombie state.
- Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
completely. With 'nosmt' being a popular option it's required to
unplug the half brought up sibling CPUs (due to the MCE wreckage)
completely"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n
Linus Torvalds [Sun, 31 Mar 2019 14:47:21 +0000 (07:47 -0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A small set of core updates:
- Make the watchdog respect the selected CPU mask again. That was
broken by the rework of the watchdog thread management and caused
inconsistent state and NMI watchdog being unstoppable.
- Ensure that the objtool build can find the libelf location.
- Remove dead kcore stub code"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog: Respect watchdog cpumask on CPU hotplug
objtool: Query pkg-config for libelf location
proc/kcore: Remove unused kclist_add_remap()
Linus Torvalds [Sun, 31 Mar 2019 14:44:13 +0000 (07:44 -0700)]
Merge tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three non-regression fixes.
- Our optimised memcmp could read past the end of one of the buffers
and potentially trigger a page fault leading to an oops.
- Some of our code to read energy management data on PowerVM had an
endian bug leading to bogus results.
- When reporting a machine check exception we incorrectly reported
TLB multihits as D-Cache multhits due to a missing entry in the
array of causes.
Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
Segher Boessenkool, Vaidyanathan Srinivasan"
* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries/mce: Fix misleading print for TLB mutlihit
powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
powerpc/64: Fix memcmp reading past the end of src/dest
Linus Torvalds [Sun, 31 Mar 2019 14:42:39 +0000 (07:42 -0700)]
Merge tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Revert "dmaengine: stm32-mdma: Add a check on read_u32_array" as that
caused regression
- Fix MAINTAINER file uniphier-mdmac.c file path
* tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma:
MAINTAINERS: Fix uniphier-mdmac.c file path
dmaengine: stm32-mdma: Revert "dmaengine: stm32-mdma: Add a check on read_u32_array"
Linus Torvalds [Sat, 30 Mar 2019 19:12:56 +0000 (12:12 -0700)]
Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix refcnt leak on interface rename
- use memcpy in device_name_store() to avoid including garbage from a
previous, longer value in the device_name
- fix a potential NULL pointer dereference in case of_match_device()
cannot find a match
* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: trigger: netdev: use memcpy in device_name_store
leds: pca9532: fix a potential NULL pointer dereference
leds: trigger: netdev: fix refcnt leak on interface rename
Linus Torvalds [Sat, 30 Mar 2019 18:33:34 +0000 (11:33 -0700)]
Merge tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"As you can see [in the git history] I was away on leave and Bartosz
kindly stepped in and collected a slew of fixes, I pulled them into my
tree in two sets and merged some two more fixes (fixing my own caused
bugs) on top.
Summary:
- Revert the extended use of gpio_set_config() and think about how we
can do this properly.
- Fix up the SPI CS GPIO handling so it now works properly on the SPI
bus children, as intended.
- Error paths and driver fixes"
* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mockup: use simple_read_from_buffer() in debugfs read callback
gpio: of: Fix of_gpiochip_add() error path
gpio: of: Check for "spi-cs-high" in child instead of parent node
gpio: of: Check propname before applying "cs-gpios" quirks
gpio: mockup: fix debugfs read
Revert "gpio: use new gpio_set_config() helper in more places"
gpio: aspeed: fix a potential NULL pointer dereference
gpio: amd-fch: Fix bogus SPDX identifier
gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
gpio: exar: add a check for the return value of ida_simple_get fails
Rasmus Villemoes [Thu, 14 Mar 2019 14:06:14 +0000 (15:06 +0100)]
leds: trigger: netdev: use memcpy in device_name_store
If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example
I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.
This is also preparation for future patches.
Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger") Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Linus Torvalds [Sat, 30 Mar 2019 17:35:20 +0000 (10:35 -0700)]
Merge tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for 5.1-rc3, and one driver
removal.
The biggest thing here is the removal of the mt7621-eth driver as a
"real" network driver was merged in 5.1-rc1 for this hardware, so this
old driver can now be removed.
Other than that, there are just a number of small fixes, all resolving
reported issues and some potential corner cases for error handling
paths.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: Remove vif check from vnt_interrupt
staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
staging: octeon-ethernet: fix incorrect PHY mode
staging: vc04_services: Fix an error code in vchiq_probe()
staging: erofs: fix error handling when failed to read compresssed data
staging: vt6655: Fix interrupt race condition on device start up.
staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
staging: rtl8712: uninitialized memory in read_bbreg_hdl()
staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
staging, mt7621-pci: fix build without pci support
staging: speakup_soft: Fix alternate speech with other synths
staging: axis-fifo: add CONFIG_OF dependency
staging: olpc_dcon_xo_1: add missing 'const' qualifier
staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
staging: erofs: fix to handle error path of erofs_vmap()
staging: mt7621-dts: update ethernet settings.
staging: remove mt7621-eth
Linus Torvalds [Sat, 30 Mar 2019 17:30:38 +0000 (10:30 -0700)]
Merge tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.1-rc3.
Nothing major here, just a number of potential problems fixes for
error handling paths, as well as some other minor bugfixes for
reported issues with 5.1-rc1.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix NULL pointer issue when tty_port ops is not set
Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
dt-bindings: serial: Add compatible for Mediatek MT8183
tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
tty/serial: atmel: Add is_half_duplex helper
serial: sh-sci: Fix setting SCSCR_TIE while transferring data
serial: ar933x_uart: Fix build failure with disabled console
tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
tty: mxs-auart: fix a potential NULL pointer dereference
tty: atmel_serial: fix a potential NULL pointer dereference
serial: max310x: Fix to avoid potential NULL pointer dereference
serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference
Linus Torvalds [Sat, 30 Mar 2019 17:26:36 +0000 (10:26 -0700)]
Merge tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.1-rc3.
Nothing major at all here, just a small collection of fixes for
reported issues, and potential problems with error handling paths.
Also a few new device ids, as normal.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Olicard 600
USB: serial: cp210x: add new device id
usb: u132-hcd: fix resource leak
usb: cdc-acm: fix race during wakeup blocking TX traffic
usb: mtu3: fix EXTCON dependency
usb: usb251xb: fix to avoid potential NULL pointer dereference
usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
xhci: Don't let USB3 ports stuck in polling state prevent suspend
usb: xhci: dbc: Don't free all memory with spinlock held
xhci: Fix port resume done detection for SS ports with LPM enabled
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
USB: gadget: f_hid: fix deadlock in f_hidg_write()
usb: gadget: net2272: Fix net2272_dequeue()
usb: gadget: net2280: Fix net2280_dequeue()
usb: gadget: net2280: Fix overrun of OUT messages
usb: dwc3: pci: add support for Comet Lake PCH ID
usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
usb: common: Consider only available nodes for dr_mode
usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
...
Linus Torvalds [Sat, 30 Mar 2019 17:09:11 +0000 (10:09 -0700)]
Merge tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This corrects a previous attempt to make Linux use its own set of ACPI
debug flags different from the upstream ACPICA's default (Erik
Schmauss)"
* tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: use different default debug value than ACPICA
Linus Torvalds [Sat, 30 Mar 2019 17:06:09 +0000 (10:06 -0700)]
Merge tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix CPU base frequency reporting in the intel_pstate driver and
a use-after-free in the scpi-cpufreq driver.
Specifics:
- Fix the ACPI CPPC library to actually follow the specification when
decoding the guaranteed performance register information and make
the intel_pstate driver to fall back to the nominal frequency when
reporting the base frequency if the guaranteed performance register
information is not there (Srinivas Pandruvada).
- Fix use-after-free in the exit callback of the scpi-cpufreq left
after an update during the 5.0 development cycle (Vincent Stehlé)"
* tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi: Fix use after free
cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
ACPI / CPPC: Fix guaranteed performance handling
Linus Torvalds [Sat, 30 Mar 2019 16:19:09 +0000 (09:19 -0700)]
Merge branch 'fixes-v5.1-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer fixes from James Morris:
"Yama and LSM config fixes"
* 'fixes-v5.1-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
LSM: Revive CONFIG_DEFAULT_SECURITY_* for "make oldconfig"
Yama: mark local symbols as static
Linus Torvalds [Fri, 29 Mar 2019 23:02:28 +0000 (16:02 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
fs: fs_parser: fix printk format warning
checkpatch: add %pt as a valid vsprintf extension
mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
drivers/block/zram/zram_drv.c: fix idle/writeback string compare
mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
mm/memory_hotplug.c: fix notification in offline error path
ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK
fs/proc/kcore.c: make kcore_modules static
include/linux/list.h: fix list_is_first() kernel-doc
mm/debug.c: fix __dump_page when mapping->host is not set
mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
include/linux/hugetlb.h: convert to use vm_fault_t
iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
mm: add support for kmem caches in DMA32 zone
ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
mm/hotplug: fix offline undo_isolate_page_range()
fs/open.c: allow opening only regular files during execve()
mailmap: add Changbin Du
mm/debug.c: add a cast to u64 for atomic64_read()
...
projects / linux.git / log