iio: mma8452: use runtime pm instead of device specific autosleep
What is this autosleep?
-----------------------
It slows down the device after x seconds of inactivity. The thing is, we have
really achieved almost the same by runtime pm.
differnces are:
autosleep
* uses more power during inactivity
* the first read after inactivity slightly faster
* complicated to understand for the user
* no documented sysfs interface (afaik)
* complicated to read and maintain
runtime pm
* already merged in mma8452
* uses less power during inactivity
* first read after inactivity slower
* easy to use. well documented.
* easy to maintain and understand
The two approaches solve the same problem. runtime pm has more advantages
than autosleep and comes quite close to it's behaviour anyways. As I see it,
autosleep, even if somehow supported, would never be used anyways.
So resolve this issue by "ignoring" autosleep.
Signed-off-by: Martin Kepplinger <martink@posteo.de> Reviewed-by: Martina Kepplinger <martina.novakovic@zoho.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Joachim Eastwood [Sat, 12 Mar 2016 12:30:16 +0000 (13:30 +0100)]
iio: dac: add NXP LPC18xx DAC driver
Add base support for the 10-bit DAC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support DMA or
interrupts.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Joachim Eastwood [Sat, 12 Mar 2016 12:30:14 +0000 (13:30 +0100)]
iio: adc: add NXP LPC18xx ADC driver
Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is often the case that the driver wants to be sure a device stays
in direct mode while it is executing a task or series of tasks. To
accomplish this today, the driver performs this sequence: 1) take the
device state lock, 2) verify it is not in a buffered mode, 3) execute
some tasks, and 4) release that lock.
This patch introduces a pair of helper functions that simplify these
steps and make it more semantically expressive.
iio_device_claim_direct_mode()
If the device is not in any buffered mode it is guaranteed
to stay that way until iio_release_direct_mode() is called.
iio_device_release_direct_mode()
Release the claim. Device is no longer guaranteed to stay
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADIS16220 part has been obsoleted, which makes it hard to get the
hardware to even test the driver. Considering this there is no expectation
that the driver will be cleaned up and be able to move out of staging, so
remove the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADIS16204 part has been obsoleted, which makes it hard to get the
hardware to even test the driver. Considering this there is no expectation
that the driver will be cleaned up and be able to move out of staging, so
remove the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: mma8452: add support for runtime power management
This adds support for runtime power management and, if configured, activates
automatic standby after 2 seconds of inactivity.
Inactivity means no read of acceleration values and no events triggered or
activated.
If CONFIG_PM is not set, this doesn't change anything for existing users.
Signed-off-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: mma8452: avoid switching to active because of config change
The devices' config registers can only be changed in standby mode.
Up until now the driver just held the device *always* active, so for
changing a config it was *always* necessary to switch to standby.
For upcoming support for runtime pm, the device can as well be in standby
mode. Instead of putting runtime pm functions in there, just keep the
device in standby if it already is. This section is protected by a lock
after all.
Signed-off-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fix checkpatch issues like "space before tabs", too long lines or alignment.
Signed-off-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Gregor Boirie [Thu, 3 Mar 2016 10:44:05 +0000 (11:44 +0100)]
iio:magnetometer:ak8975: power regulator support
Add support for an optional regulator which, if found into device-tree,
will power on device at probing time.
The regulator is declared into ak8975 DTS entry as a "vdd-supply" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ak_def_array bounds are not properly checked in case of ACPI matching
failure. GCC warns with the following message at line 799:
‘chipset’ may be used uninitialized in this function.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Gregor Boirie [Tue, 1 Mar 2016 10:31:38 +0000 (11:31 +0100)]
iio:pressure:ms5611: oversampling rate support
Add support for setting and retrieving OverSampling Rate independently for
each of the temperature and pressure channels. This allows userspace to
fine tune hardware sampling process according to the following tradeoffs :
* the higher the OSR, the finer the resolution ;
* the higher the OSR, the lower the noise ;
BUT:
* the higher the OSR, the larger the drift ;
* the higher the OSR, the longer the response time, i.e. less samples per
unit of time.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Liang Zhen [Wed, 2 Mar 2016 23:53:30 +0000 (18:53 -0500)]
staging: lustre: do less intense allocating retry for ko2iblnd
ko2iblnd may retry too frequent for growing pools, all schedulers
are spinning if another thread is in progress of allocating a new
pool and can't finish right away because of high system load.
Liang Zhen [Wed, 2 Mar 2016 23:53:29 +0000 (18:53 -0500)]
staging: lustre: avoid intensive reconnecting for ko2iblnd
When there is a connection race between two nodes and one side
of the connection is rejected by the other side. o2iblnd will
reconnect immediately, this is going to generate a lot of
trashes if:
- race winner is slow and can't send out connecting request
in short time.
- remote side leaves a cmid in TIMEWAIT state, which will reject
future connection requests
To resolve this problem, this patch changed the reconnection
behave: reconnection is submitted by connd only if a zombie
connection is being destroyed and there is a pending
reconnection request for the corresponding peer.
Also, after a few rejections, reconnection will have a time
interval between each attempt.
Liang Zhen [Wed, 2 Mar 2016 23:53:28 +0000 (18:53 -0500)]
staging: lustre: check wr_id returned by ib_poll_cq
If ib_poll_cq returned +ve without initialising ib_wc::wr_id (bug
in driver), then o2iblnd will run into unpredictable situation
because ib_wc::wr_id may refer to stale tx/rx pointer in stack.
It indicates bug in HCA driver if this happened, ko2iblnd should
output console error then close current connection.
Doug Oucharek [Wed, 2 Mar 2016 23:53:27 +0000 (18:53 -0500)]
staging: lustre: Change connect peer failed cleanup order
A race condition has been found where connd is cleaning up failed
connections, the peer ref counter goes to zero, but we stil have
a connecting counter > 0.
One possible race is when we are retrying a connection by
calling kiblnd_connect_peer() which itself fails and decrements
the peer ref counter and gets swapped out before it can decrement
the connecting counter. connd swaps in and cleans up the
connection where it sees a peer ref counter of 1 and a connecting
counter of 1. This will trigger the assert seen in LU-7210 when
it decrements the peer counter.
The solution: be sure to decrement the connecting counter
before decrementing the peer counter in the peer connect
failure path.
Liang Zhen [Wed, 2 Mar 2016 23:53:26 +0000 (18:53 -0500)]
staging: lustre: take extra refcount in kiblnd_connreq_done
refcount taken by cmid is not reliable after kiblnd_connreq_done
released the glock because this connection is visible to other
threads, another thread can find and close this connection right
after kiblnd_connreq_done released the glock, if kiblnd_cm_callback
for RDMA_CM_EVENT_DISCONNECTED is called, it can release the
connection refcount taken by cmid. It means the connection could be
destroyed before kiblnd_connreq_done() finish operations on it.
Amir Shehata [Wed, 2 Mar 2016 23:53:25 +0000 (18:53 -0500)]
staging: lustre: make ko2iblnd connect parameters persistent
Store map-on-demand and peertx credits in the peer, since the peer
is persistent. Also made sure that when assigning the parameters
received on the connection to the peer structure through create,
that if another peer is added before grabbing the lock we assign
these parameters to it as well.
Bhumika Goyal [Wed, 2 Mar 2016 19:16:37 +0000 (00:46 +0530)]
Staging: lustre: lnet: Remove and rename struct typedefs
Remove typedefs from structures stt_timer_t and lst_ping_data_t as typedef
for a structure type is not preferred. The suffix '_t' and the typedefs
are removed using coccinelle.
Script 1:
//Drop typedefs and '_t'
@r1@
type T;
@@
typedef struct { ... } T;
@script:python c1@
T2;
T << r1.T;
@@
if T[-2:] =="_t":
coccinelle.T2 = T[:-2];
print T
else:
coccinelle.T2=T;
staging: lustre: llite: Remove unnecessary test in if condition
Remove unnecessary test on `rc` variable since it has already been
tested previously.
Fixes following smatch warning:
drivers/staging/lustre/lustre/llite/llite_lib.c:1331 ll_setattr_raw()
warn: we tested 'rc' before and it was 'false'
James Simmons [Wed, 2 Mar 2016 22:01:59 +0000 (17:01 -0500)]
staging: lustre: reverse LNet and infinband header order
LNet is an abstraction built on top of network APIs such
as infiniband or TCP/IP layer. Since LNet is dependent
on these other layers we should ensure LNet headers
should always come after the infiniband header since the
infiniband headers can influence the LNet header
definitions.
Dmitry Eremin [Wed, 2 Mar 2016 22:01:58 +0000 (17:01 -0500)]
staging: lustre: fix framework.c issues found by Klocwork Insight tool
The functions sfw_test_buffers() and sfw_unload_test() from LNet
selftest both assume sfw_test_instance_t being passed in is never
null. This is corrected here.
Signed-off-by: Dmitry Eremin <dmitry.eremin@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4629
Reviewed-on: http://review.whamcloud.com/9386 Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Isaac Huang <he.huang@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Eremin [Wed, 2 Mar 2016 22:01:57 +0000 (17:01 -0500)]
staging: lustre: fix conctl.c issues found by Klocwork Insight tool
The function lst_test_add_ioctl is always copying lstio_tes_param
from userland even if the user doesn't send this data to LNet
selftest. Only consider lstio_tes_param data if lstio_tes_param_len
is not zero.
Signed-off-by: Dmitry Eremin <dmitry.eremin@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4629
Reviewed-on: http://review.whamcloud.com/9386 Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Isaac Huang <he.huang@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Eremin [Wed, 2 Mar 2016 22:01:56 +0000 (17:01 -0500)]
staging: lustre: fix api-ni.c issues found by Klocwork Insight tool
Pointer 'ni' checked for NULL at line 1569 may be passed to
function and may be dereferenced there by passing argument 1 to
function 'lnet_ni_notify_locked' at line 1621.
Signed-off-by: Dmitry Eremin <dmitry.eremin@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-4629
Reviewed-on: http://review.whamcloud.com/9386 Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Isaac Huang <he.huang@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Simmons [Wed, 2 Mar 2016 22:01:54 +0000 (17:01 -0500)]
staging: lustre: bind socklnd peers to a specific CPT
Currently the socklnd driver doesn't support
CPT affinity for its peers. Binding peers to
a specific CPT and memory allocated to the
NUMA node belonging to the CPT should give a
performance boost.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7245
Reviewed-on: http://review.whamcloud.com/16710 Reviewed-by: Olaf Weber <olaf@sgi.com> Reviewed-by: Amir Shehata <amir.shehata@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jian Yu [Wed, 2 Mar 2016 22:01:53 +0000 (17:01 -0500)]
staging: lustre: replace direct LNet HZ access with kernel APIs
On some customers' systems, the kernel was compiled with HZ defined
to 100, instead of 1000. This improves performance for HPC applications.
However, to use these systems with Lustre, customers have to re-build
Lustre for the kernel because Lustre directly uses the defined constant
HZ.
Since kernel 2.6.21, some non-HZ dependent timing APIs become non-
inline functions, which can be used in Lustre codes to replace the
direct HZ access.
These kernel APIs include:
jiffies_to_msecs()
jiffies_to_usecs()
jiffies_to_timespec()
msecs_to_jiffies()
usecs_to_jiffies()
timespec_to_jiffies()
And here are some samples of the replacement:
HZ -> msecs_to_jiffies(MSEC_PER_SEC)
n * HZ -> msecs_to_jiffies(n * MSEC_PER_SEC)
HZ / n -> msecs_to_jiffies(MSEC_PER_SEC / n)
n / HZ -> jiffies_to_msecs(n) / MSEC_PER_SEC
n / HZ * 1000 -> jiffies_to_msecs(n)
This patch replaces the direct HZ access in lnet module.
John L. Hammond [Wed, 2 Mar 2016 22:01:52 +0000 (17:01 -0500)]
staging: lustre: set task state before scheduling in lnet_sock_accept
In the original code change when libcfs_sock_accept() was made
into lnet_sock_accept() a call to set_current_state(TASK_INTERRUPTIBLE)
got dropped which was restored. For upstream this is an
optimization of calling init_waitqueue_entry() only if
accept() return -EAGAIN. Also we can remove setting the
task to TASK_RUNNING that is not needed.
Signed-off-by: John L. Hammond <john.hammond@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6407
Reviewed-on: http://review.whamcloud.com/14265 Reviewed-by: James Simmons <uja.ornl@yahoo.com> Reviewed-by: Amir Shehata <amir.shehata@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: lustre: fix 'copy into fixed size buffer' errors
Fix 'copy into fixed size buffer' defects found by Coverity
version 6.0.3:
Copy into fixed size buffer (STRING_OVERFLOW)
The fixed-size string might be overrun by copying without
checking the length.
Olaf Weber [Wed, 2 Mar 2016 22:01:49 +0000 (17:01 -0500)]
staging: lustre: Use after free in lnet_ptl_match_delay()
In lnet_ptl_match_delay() we check msg->msg_rx_delayed to see whether
the message has been added to the delay queue. But this check is done
after lnet_ptl_unlock() and lnet_res_unlock(), and the message can be
processed and freed before the check.
Replace the check with checking rc against LNET_MATCHMD_NONE, which
is how the callers of lnet_ptl_match_delay() know whether the message
was added to the delay queue. To make this work we reset rc in the
loop when there was no match and the message hasn't been delayed. In
addition reorganize the code and add comments to clarify the logic.
In lnet_ptl_match_md() a similar msg->msg_rx_delayed is replaced for
the same reason.
Li Xi [Wed, 2 Mar 2016 22:01:48 +0000 (17:01 -0500)]
staging: lustre: remove annoying message in parse_nidrange
When setting TBF rules of jobid, parse_nidrange() prints warning
messages. However, this is unnecessary and annoying since paring
a TBF rule will always try to parse the jobid like a nid.
Signed-off-by: Li Xi <lixi@ddn.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7647
Reviewed-on: http://review.whamcloud.com/17916 Reviewed-by: Emoly Liu <emoly.liu@intel.com> Reviewed-by: Bobi Jam <bobijam@hotmail.com> Reviewed-by: Lai Siyao <lai.siyao@intel.com> Reviewed-by: James Simmons <uja.ornl@yahoo.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amir Shehata [Wed, 2 Mar 2016 22:01:46 +0000 (17:01 -0500)]
staging: lustre: Ignore hops if not explicitly set
Since the # of hops is not a mandatory parameter the LU-6060
patch will cause problems to already existing systems since it
changes the behavior by which a route is determined down.
To fix this case the # of hops now defaults to LNET_UNDEFINED_HOPS
if no hop count is specified.
LNET_UNDEFINED_HOPS is defined to ((__u32)-1). When it's printed as
%d, it displays as -1.
__u32 is used through out the call stack for hop count to explicitly
define the size of the hop count and to avoid any sizing issues when
passing data to and from the kernel.
To keep existing behavior both lnet_compare_routes() and LNetDist()
will treat undefined hop count as hop count 1.
When executing the logic in lnet_parse_rc_info() there is no
longer an assumption that the default hop count is 1. If
the hop count is 1 then it must've been explicitly set by
the user.
Liang Zhen [Wed, 2 Mar 2016 22:01:45 +0000 (17:01 -0500)]
staging: lustre: recv could access freed message
When lnet_parse_put calls lnet_ptl_match_md, this function can attach
current message on the delayed list if there is no match. It means
this message can be taken over and freed by another thread who is
posting new MD, then it is not safe for caller of lnet_parse_put to
check this message again.
This patch fixes this issue by adding a local variable "ready_delay"
to store corresponding status of lnet_msg, so lnet doesn't need to
check the message again if lnet_ptl_match_md returned MATCH_NONE for
it.
Liang Zhen [Wed, 2 Mar 2016 22:01:44 +0000 (17:01 -0500)]
staging: lustre: set downis to 1 if there's no NI for remote net
lnet_route_t::lr_downis is marked as zero even if there is no NI to
target network, this is wrong and breaks logic of ARF. This patch
fixes this problem.
Oleg Drokin [Wed, 2 Mar 2016 13:25:39 +0000 (08:25 -0500)]
staging/lustre: Unbreak ll_prep_inode iget result check
commit 020ecc6f3229 ("staging: lustre: llite: Remove IS_ERR tests")
managed to break one of the converted checks by losing a dereference
causing the condition to be wrong and hence leading
to a crash later on in case of actual error.
IS_ERR_OR_NULL(*inode) got converted into !inode.
staging: wilc1000: wilc_wlan: Remove wrapper function
Remove is_tcp_ack_filter() which only returns the value of boolean
variable `enabled` by replacing the only call site with the variable
`enabled` itself.
Variables pcgroup_encrypt_val,pccipher_group,pcwpa_version,
hold different values at different stages of the execution of
connect(), however they are not being used anywhere.
Hence, the unused variables have been removed.
This was done using Coccinelle.
@@ type T; identifier i; constant c; @@
-T i;
<... when != i
-i = c;
...>
Alison Schofield [Fri, 26 Feb 2016 07:03:42 +0000 (23:03 -0800)]
staging: wilc1000: remove code for HOST_IF_MSG_SET_MAC_ADDRESS
The function that sent this message id was previously removed.
Finish the cleanup by removing the call to the message handler,
the message handler, and the #define.
Alison Schofield [Fri, 26 Feb 2016 07:02:59 +0000 (23:02 -0800)]
staging: wilc1000: remove code for HOST_IF_MSG_Q_IDLE
The function that sent this message id was previously removed.
Finish the cleanup by removing the call to the message handler,
the message handler, and the #define.
Alison Schofield [Fri, 26 Feb 2016 07:02:17 +0000 (23:02 -0800)]
staging: wilc1000: remove code for HOST_IF_MSG_FLUSH_CONNECT
The function that sent this message id was previously removed.
Finish the cleanup by removing the call to the message handler,
the message handler, and the #define.
Alison Schofield [Fri, 26 Feb 2016 07:01:13 +0000 (23:01 -0800)]
staging: wilc1000: remove code for HOST_IF_GET_LINKSPEED
The function that sent this message id was previously removed.
Finish the cleanup by removing the call to the message handler,
the message handler, the #define, and the link_speed var.
Alison Schofield [Fri, 26 Feb 2016 07:00:42 +0000 (23:00 -0800)]
staging: wilc1000: remove code for HOST_IF_MSG_GET_CHNL
The function that sent this message id was previously removed.
Finish the cleanup by removing the call to the message handler,
the message handler, the #define, and the channel var.
Bhumika Goyal [Sun, 28 Feb 2016 19:44:33 +0000 (01:14 +0530)]
Staging: lustre: Remove print statement on function failure
The memory allocation functions generates a call stack containing
all the context information on failure, so print statements can be
removed on failure of these functions. Also remove
unwanted {} around if block after removal of these statements.
Done using coccinelle:
M. Vefa Bicakci [Sun, 28 Feb 2016 14:26:22 +0000 (09:26 -0500)]
staging: lustre: Use __user for a pointer to a user space address
This commit corrects two sparse warnings caused by the lack of a __user
annotation for the third argument of the libcfs_ioctl_handle function.
module.c:165:68: warning: incorrect type in argument 1
(different address spaces)
module.c:165:68: expected void [noderef] <asn:1>*arg
module.c:165:68: got void *arg
module.c:209:47: warning: incorrect type in argument 3
(different address spaces)
module.c:209:47: expected void *arg
module.c:209:47: got void [noderef] <asn:1>*arg
The need to have the __user annotation is supported by the fact that
libcfs_ioctl_handle passes its third argument to a helper function
(libcfs_ioctl_popdata) which also has a __user annotation for its
corresponding argument.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
M. Vefa Bicakci [Sun, 28 Feb 2016 14:26:21 +0000 (09:26 -0500)]
staging: lustre: Use const static file_operations struct
This commit corrects the following sparse warning regarding a
file_operations structure being non-static and constifies the
structure in question as well.
warning: symbol 'lprocfs_stats_seq_fops' was not declared.
Should it be static?
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: lustre: lnet: Use list_for_each_entry_safe
Doubly linked lists which are iterated using list_empty
and list_entry macros have been replaced with list_for_each_entry_safe macro.
This makes the iteration simpler and more readable.
This patch replaces the while loop containing list_empty and list_entry
with list_for_each_entry_safe.
This was done with Coccinelle.
@@
expression E1;
identifier I1, I2;
type T;
iterator name list_for_each_entry_safe;
@@
T *I1;
+ T *tmp;
...
- while (list_empty(&E1) == 0)
+ list_for_each_entry_safe (I1, tmp, &E1, I2)
{
...when != T *I1;
- I1 = list_entry(E1.next, T, I2);
...
}
Andreas Dilger [Fri, 26 Feb 2016 16:36:06 +0000 (11:36 -0500)]
staging: lustre: update comment for lnet_lib_init/exit
The documentation about the return values for lnet_lib_init
and lnet_lib_exit was in the old style format. Bring it in
sync with the rest of the LNet core. Broken out of patch 16787.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6204
Reviewed-on: http://review.whamcloud.com/16787 Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com> Reviewed-by: Frank Zago <fzago@cray.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Dilger [Fri, 26 Feb 2016 16:36:04 +0000 (11:36 -0500)]
staging: lustre: update the MODULE_DESCRIPTION for all lustre modules
Fixup the MODULE_DESCRIPTION for several lustre modules. Some wrongly
place the version in the string or they are not descriptive enough.
Broken out of patch http://review.whamcloud.com/16787.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6204
Reviewed-on: http://review.whamcloud.com/16787 Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com> Reviewed-by: Frank Zago <fzago@cray.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Simmons [Fri, 26 Feb 2016 16:36:03 +0000 (11:36 -0500)]
staging: lustre: add missing MODULE_AUTHOR for LNet selftest module
For several lustre modules the MODULE_VERSION has the wrong value,
located in the wrong place in the source code, or completely missing.
This patch brings it up to date.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6204
Reviewed-on: http://review.whamcloud.com/16729 Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: Frank Zago <fzago@cray.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: lustre: llite: Replace kmem_cache_alloc with kmem_cache_zalloc
Use kmem_cache_zalloc instead of manually setting kmem_cache_alloc
with flag GFP_ZERO since kmem_alloc_zalloc sets allocated memory
to zero.
The Coccinelle semantic patch used to make this change is as
follows:
// <smpl>
@@
expression e,f;
@@
- kmem_cache_alloc(e, f |__GFP_ZERO)
+ kmem_cache_zalloc(e, f)
// </smpl>
staging: lustre: ldlm: Replace kmem_cache_alloc with kmem_cache_zalloc
Use kmem_cache_zalloc instead of manually setting kmem_cache_alloc
with flag GFP_ZERO since kmem_alloc_zalloc sets allocated memory
to zero.
The Coccinelle semantic patch used to make this change is as
follows:
// <smpl>
@@
expression e,f;
@@
- kmem_cache_alloc(e, f |__GFP_ZERO)
+ kmem_cache_zalloc(e, f)
// </smpl>