Gregory CLEMENT [Fri, 15 Nov 2019 15:57:52 +0000 (16:57 +0100)]
pinctrl: armada-37xx: Fix irq mask access in armada_37xx_irq_set_type()
As explained in the following commit a9a1a4833613 ("pinctrl:
armada-37xx: Fix gpio interrupt setup") the armada_37xx_irq_set_type()
function can be called before the initialization of the mask field.
That means that we can't use this field in this function and need to
workaround it using hwirq.
Fixes: 30ac0d3b0702 ("pinctrl: armada-37xx: Add edge both type gpio irq support") Cc: stable@vger.kernel.org Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Link: https://lore.kernel.org/r/20191115155752.2562-1-gregory.clement@bootlin.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rahul Tanwar [Fri, 15 Nov 2019 09:25:07 +0000 (17:25 +0800)]
pinctrl: Add pinmux & GPIO controller driver for a new SoC
Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
controls pin multiplexing & configuration including GPIO functions selection &
GPIO attributes configuration.
This IP is not based on & does not have anything in common with Chassis
specification. The pinctrl drivers under pinctrl/intel/* are all based upon
Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
Add a new GPIO & pin control framework based driver for this IP.
Matti Vaittinen [Wed, 13 Nov 2019 07:10:45 +0000 (09:10 +0200)]
pinctrl: rza1: remove unnecessary static inline function
Having static inline oneliner does not benefit too much when it is
only called from another oneliner function. Remove some of the
'onion'. This simplifies also the coming usage of the gpiolib
defines. We can do conversion from chip bits to gpiolib direction
defines as last step in the get_direction callback. Drivers can
use chip specific values in driver internal functions and do
conversion only once.
Qianggui Song [Fri, 15 Nov 2019 12:03:48 +0000 (20:03 +0800)]
pinctrl: meson: add pinctrl driver support for Meson-A1 SoC
Meson A1 SoC share the same register layout of pinmux with previous
Meson-G12A, however there is difference for gpio and pin config register
in A1. The main difference is that registers before A1 are grouped by
function while those of A1 are by bank. The new register layout is as
below:
/* first bank */ /* addr */
- P_PADCTRL_GPIOP_I base + 0x00 << 2
- P_PADCTRL_GPIOP_O base + 0x01 << 2
- P_PADCTRL_GPIOP_OEN base + 0x02 << 2
- P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2
- P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2
- P_PADCTRL_GPIOP_DS base + 0x05 << 2
/* second bank */
- P_PADCTRL_GPIOB_I base + 0x10 << 2
- P_PADCTRL_GPIOB_O base + 0x11 << 2
- P_PADCTRL_GPIOB_OEN base + 0x12 << 2
- P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2
- P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2
- P_PADCTRL_GPIOB_DS base + 0x15 << 2
Each bank contains at least 6 registers to be configured, if one bank
has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included.
Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that
is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24
,0x25 according to above register layout. For previous chips, registers
are grouped according to their functions while registers of A1 are
according to bank.Also note that there is no AO bank any more in A1.
Current Meson pinctrl driver can cover such change by using base address
of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen
make wrong value to reg_ds for Socs that do not support drive-strength
like AXG.To make things simple, add an extra dt parser function for
a1 and remain the old dt parser function for only reg parsing.
Qianggui Song [Fri, 15 Nov 2019 12:03:47 +0000 (20:03 +0800)]
pinctrl: meson: add a new callback for SoCs fixup
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and
SoC relative fixup for AO. Several fixups in the same code make it hard
to maintain, so move all fixups to each SoC's callback and make
meson_pinctrl_parse_dt just do the reg parsing, separate these two
parts.Overview of all current Meson SoCs fixup is as below:
+------+--------------------------------------+--------------------------+
| | | |
| SoC | EE domain | AO domain |
+------+--------------------------------------+--------------------------+
|m8 | parse regs: | parse regs: |
|m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)|
|gxl | fixup: | fixup: |
|gxbb | no | pull-enable = pull; |
|axg | | |
+------+--------------------------------------+--------------------------+
|g12a | parse regs: | parse regs: |
|sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds |
| | fixup: | fixup: |
| | no | pull = gpio; |
| | | pull-enable = gpio; |
+------+--------------------------------------+--------------------------+
|a1 or | parse regs: |
|later | gpio/mux (without ao domain) |
|SoCs | fixup: |
| | pull = gpio; pull-enable = gpio; ds = gpio; |
+------+-----------------------------------------------------------------+
Since m8-axg share the same ao fixup, make a common function
meson8_aobus_parse_dt_extra to do the job.
Stephan Gerhold [Sun, 17 Nov 2019 20:54:39 +0000 (21:54 +0100)]
pinctrl: nomadik: db8500: Add mc0_a_2 pin group without direction control
Some devices do not make use of the CMD0/DAT0/DAT2 direction control
pins of the MMC/SD card 0 interface. In this case we should leave
those pins unconfigured.
A similar case already exists for "mc1_a_1" vs "mc1_a_2"
when the MC1_FBCLK pin is not used.
Add a new "mc0_a_2" pin group which is equal to "mc0_a_1" except
with the MC0_CMDDIR, MC0_DAT0DIR and MC0_DAT2DIR pins removed.
Linus Walleij [Wed, 13 Nov 2019 22:11:09 +0000 (23:11 +0100)]
Merge tag 'intel-pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.5-1
* Intel Tigerlake pin controller support has been added.
* Miscellaneous fixes to the main and Cherryview drivers.
* Refactoring of the context restoring in the main driver.
The following is an automated git shortlog grouped by driver:
cherryview:
- Missed type change to unsigned int
- Allocate IRQ chip dynamic
- Fix spelling mistake in the comment
- Fix irq_valid_mask calculation
intel:
- Missed type change to unsigned int
- Add Intel Tiger Lake pin controller support
- Use helper to restore register values on ->resume()
- Drop level from warning to debug in intel_restore_hostown()
- Introduce intel_restore_intmask() helper
- Introduce intel_restore_hostown() helper
- Introduce intel_restore_padcfg() helper
- Avoid potential glitches if pin is in GPIO mode
Rob Herring [Thu, 7 Nov 2019 22:42:54 +0000 (16:42 -0600)]
dt-bindings: pinctrl: Convert generic pin mux and config properties to schema
As pinctrl bindings have a flexible structure and no standard child node
naming convention, creating a single pinctrl schema doesn't work. Instead,
create schemas for the pin mux and config nodes which device pinctrl schema
can reference.
YueHaibing [Mon, 4 Nov 2019 14:26:54 +0000 (22:26 +0800)]
pinctrl: use devm_platform_ioremap_resource() to simplify code
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
lijiazi [Fri, 1 Nov 2019 11:43:52 +0000 (19:43 +0800)]
pinctrl: just return if no valid maps
If there is a problem with a pinctrl node of a device,
for example, config child node do not have prop specified in
dt_params, num_maps maybe 0. On this condition, no need remember
this map.
Qianggui Song [Fri, 25 Oct 2019 11:49:24 +0000 (19:49 +0800)]
pinctrl: add compatible for Amlogic Meson A1 pin controller
Add new compatible name for Amlogic's Meson-A1 pin controller
add a dt-binding header file which document the detail pin names.
Note that A1 doesn't need DS bank reg any more, use gpio reg as
base.
Chris Packham [Mon, 4 Nov 2019 00:18:19 +0000 (13:18 +1300)]
pinctrl: bcm: nsp: implement get_direction
The get_direction api is strongly recommended to be implemented. In fact
if it is not implemented gpio-hogs will not get the correct direction.
Add an implementation of get_direction for the nsp-gpio driver.
Chris Packham [Mon, 4 Nov 2019 00:18:18 +0000 (13:18 +1300)]
pinctrl: bcm: nsp: use gpiolib infrastructure for interrupts
Use more of the gpiolib infrastructure for handling interrupts. The
root interrupt still needs to be handled manually as it is shared with
other peripherals on the SoC.
This will allow multiple instances of this driver to be supported and
will clean up gracefully on failure thanks to the device managed APIs.
Rajendra Nayak [Mon, 21 Oct 2019 14:15:07 +0000 (19:45 +0530)]
pinctrl: qcom: sc7180: Add missing tile info in SDC_QDSD_PINGROUP/UFS_RESET
The SDC_QDSD_PINGROUP/UFS_RESET macros are missing the .tile info needed to
calculate the right register offsets. Adding them here and also
adjusting the offsets accordingly.
pinctrl: at91: Enable slewrate by default on SAM9X60
On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.
This patch changes the ABI. However, the slewrate macros are only used
by SAM9X60 and, at this moment, there are no device-tree files available
for this platform.
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
pinctrl: sh-pfc: Rename PINCTRL_PFC_R8A7796 to PINCTRL_PFC_R8A77960
Rename CONFIG_PINCTRL_PFC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_PINCTRL_PFC_R8A77960, to avoid confusion with R-Car M3-W+
(R8A77961), which will use CONFIG_PINCTRL_PFC_R8A77961.
Extend the dependency of CONFIG_PINCTRL_PFC_R8A77960 from
CONFIG_ARCH_R8A7796 to CONFIG_ARCH_R8A77960, to relax dependencies for a
future rename of the SoC configuration symbol.
Rename r8a7796_pinmux_info to r8a77960_pinmux_info, as it contains an
r8a77960-based name.
pinctrl: sh-pfc: Do not use platform_get_irq() to count interrupts
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Andy Shevchenko [Mon, 21 Oct 2019 16:45:28 +0000 (19:45 +0300)]
pinctrl: intel: Add Intel Tiger Lake pin controller support
This driver adds pinctrl/GPIO support for Intel Tiger Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Tue, 22 Oct 2019 10:00:04 +0000 (13:00 +0300)]
pinctrl: intel: Use helper to restore register values on ->resume()
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Andy Shevchenko [Tue, 22 Oct 2019 10:00:03 +0000 (13:00 +0300)]
pinctrl: intel: Drop level from warning to debug in intel_restore_hostown()
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Andy Shevchenko [Thu, 24 Oct 2019 13:34:41 +0000 (16:34 +0300)]
pinctrl: cherryview: Allocate IRQ chip dynamic
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543 Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Andy Shevchenko [Wed, 23 Oct 2019 13:32:03 +0000 (16:32 +0300)]
pinctrl: cherryview: Fix spelling mistake in the comment
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c55 ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Mon, 14 Oct 2019 09:51:04 +0000 (12:51 +0300)]
pinctrl: intel: Avoid potential glitches if pin is in GPIO mode
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip") Cc: stable@vger.kernel.org Cc: fei.yang@intel.com Reported-by: Oliver Barta <oliver.barta@aptiv.com> Reported-by: Malin Jonsson <malin.jonsson@ericsson.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Linus Torvalds [Sun, 27 Oct 2019 11:14:40 +0000 (07:14 -0400)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two fixes for the VMWare guest support:
- Unbreak VMWare platform detection which got wreckaged by converting
an integer constant to a string constant.
- Fix the clang build of the VMWAre hypercall by explicitely
specifying the ouput register for INL instead of using the short
form"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/vmware: Fix platform detection VMWARE_PORT macro
x86/cpu/vmware: Use the full form of INL in VMWARE_HYPERCALL, for clang/llvm
Linus Torvalds [Sun, 27 Oct 2019 11:04:22 +0000 (07:04 -0400)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(keeping):
- Add a missing include to prevent compiler warnings.
- Make the VDSO implementation of clock_getres() POSIX compliant
again. A recent change dropped the NULL pointer guard which is
required as NULL is a valid pointer value for this function.
- Fix two function documentation typos"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Fix two trivial comments
timers/sched_clock: Include local timekeeping.h for missing declarations
lib/vdso: Make clock_getres() POSIX compliant again
Linus Torvalds [Sun, 27 Oct 2019 10:59:34 +0000 (06:59 -0400)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of perf fixes:
kernel:
- Unbreak the tracking of auxiliary buffer allocations which got
imbalanced causing recource limit failures.
- Fix the fallout of splitting of ToPA entries which missed to shift
the base entry PA correctly.
- Use the correct context to lookup the AUX event when unmapping the
associated AUX buffer so the event can be stopped and the buffer
reference dropped.
tools:
- Fix buildiid-cache mode setting in copyfile_mode_ns() when copying
/proc/kcore
- Fix freeing id arrays in the event list so the correct event is
closed.
- Sync sched.h anc kvm.h headers with the kernel sources.
- Link jvmti against tools/lib/ctype.o to have weak strlcpy().
- Fix multiple memory and file descriptor leaks, found by coverity in
perf annotate.
- Fix leaks in error handling paths in 'perf c2c', 'perf kmem', found
by a static analysis tool"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Fix AUX output stopping
perf/aux: Fix tracking of auxiliary trace buffer allocation
perf/x86/intel/pt: Fix base for single entry topa
perf kmem: Fix memory leak in compact_gfp_flags()
tools headers UAPI: Sync sched.h with the kernel
tools headers kvm: Sync kvm.h headers with the kernel sources
tools headers kvm: Sync kvm headers with the kernel sources
tools headers kvm: Sync kvm headers with the kernel sources
perf c2c: Fix memory leak in build_cl_output()
perf tools: Fix mode setting in copyfile_mode_ns()
perf annotate: Fix multiple memory and file descriptor leaks
perf tools: Fix resource leak of closedir() on the error paths
perf evlist: Fix fix for freed id arrays
perf jvmti: Link against tools/lib/ctype.h to have weak strlcpy()
Linus Torvalds [Sun, 27 Oct 2019 10:55:55 +0000 (06:55 -0400)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixes for interrupt controller drivers:
- Skip IRQ_M_EXT entries in the device tree when initializing the
RISCV PLIC controller to avoid a double init attempt.
- Use the correct ITS list when issuing the VMOVP synchronization
command so the operation works only on the ITS instances which are
associated to a VM"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Skip contexts except supervisor in plic_init()
irqchip/gic-v3-its: Use the exact ITSList for VMOVP
Linus Torvalds [Sun, 27 Oct 2019 10:41:52 +0000 (06:41 -0400)]
Merge tag '5.4-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Seven cifs/smb3 fixes, including three for stable"
* tag '5.4-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix cifsInodeInfo lock_sem deadlock when reconnect occurs
CIFS: Fix use after free of file info structures
CIFS: Fix retry mid list corruption on reconnects
cifs: Fix missed free operations
CIFS: avoid using MID 0xFFFF
cifs: clarify comment about timestamp granularity for old servers
cifs: Handle -EINPROGRESS only when noblockcnt is set
Linus Torvalds [Sat, 26 Oct 2019 23:43:12 +0000 (19:43 -0400)]
Merge tag 'mips_fixes_5.4_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes:
- Fix VDSO time-related function behavior for systems where we need
to fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where
they would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address"
* tag 'mips_fixes_5.4_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: tlbex: Fix build_restore_pagemask KScratch restore
MIPS: bmips: mark exception vectors as char arrays
mips: vdso: Fix __arch_get_hw_counter()
MAINTAINERS: Use @kernel.org address for Paul Burton
Linus Torvalds [Sat, 26 Oct 2019 20:36:47 +0000 (16:36 -0400)]
Merge tag 'staging-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix, for the wlan-ng driver, that
resolves a reported issue.
It is been in linux-next for a while with no reported issues"
* tag 'staging-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wlan-ng: fix exit return when sme->key_idx >= NUM_WEPKEYS
Linus Torvalds [Sat, 26 Oct 2019 19:17:54 +0000 (15:17 -0400)]
Merge tag 'char-misc-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull binder fix from Greg KH:
"This is a single binder fix to resolve a reported issue by Jann. It's
been in linux-next for a while with no reported issues"
* tag 'char-misc-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: Don't modify VMA bounds in ->mmap handler
Linus Torvalds [Sat, 26 Oct 2019 19:14:55 +0000 (15:14 -0400)]
Merge tag 'usb-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.4-rc5.
More "fun" with some of the misc USB drivers as found by syzbot, and
there are a number of other small bugfixes in here for reported
issues.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdns3: Error out if USB_DR_MODE_UNKNOWN in cdns3_core_init_role()
USB: ldusb: fix read info leaks
USB: serial: ti_usb_3410_5052: clean up serial data access
USB: serial: ti_usb_3410_5052: fix port-close races
USB: usblp: fix use-after-free on disconnect
usb: udc: lpc32xx: fix bad bit shift operation
usb: cdns3: Fix dequeue implementation.
USB: legousbtower: fix a signedness bug in tower_probe()
USB: legousbtower: fix memleak on disconnect
USB: ldusb: fix memleak on disconnect
Linus Torvalds [Sat, 26 Oct 2019 19:06:58 +0000 (15:06 -0400)]
Merge branch 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A few driver fixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: remove warning when compiling with W=1
i2c: stm32f7: fix a race in slave mode with arbitration loss irq
i2c: stm32f7: fix first byte to send in slave mode
i2c: mt65xx: fix NULL ptr dereference
i2c: aspeed: fix master pending state handling
Linus Torvalds [Sat, 26 Oct 2019 18:59:51 +0000 (14:59 -0400)]
Merge tag 'for-linus-2019-10-26' of git://git.kernel.dk/linux-block
Pull block and io_uring fixes from Jens Axboe:
"A bit bigger than usual at this point in time, mostly due to some good
bug hunting work by Pavel that resulted in three io_uring fixes from
him and two from me. Anyway, this pull request contains:
- Revert of the submit-and-wait optimization for io_uring, it can't
always be done safely. It depends on commands always making
progress on their own, which isn't necessarily the case outside of
strict file IO. (me)
- Series of two patches from me and three from Pavel, fixing issues
with shared data and sequencing for io_uring.
- Lastly, two timeout sequence fixes for io_uring (zhangyi)
- Two nbd patches fixing races (Josef)
- libahci regulator_get_optional() fix (Mark)"
* tag 'for-linus-2019-10-26' of git://git.kernel.dk/linux-block:
nbd: verify socket is supported during setup
ata: libahci_platform: Fix regulator_get_optional() misuse
nbd: handle racing with error'ed out commands
nbd: protect cmd->status with cmd->lock
io_uring: fix bad inflight accounting for SETUP_IOPOLL|SETUP_SQTHREAD
io_uring: used cached copies of sq->dropped and cq->overflow
io_uring: Fix race for sqes with userspace
io_uring: Fix broken links with offloading
io_uring: Fix corrupted user_data
io_uring: correct timeout req sequence when inserting a new entry
io_uring : correct timeout req sequence when waiting timeout
io_uring: revert "io_uring: optimize submit_and_wait API"
Linus Torvalds [Sat, 26 Oct 2019 10:35:46 +0000 (06:35 -0400)]
Merge tag 's390-5.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Add R_390_GLOB_DAT relocation type support. This fixes boot problem
on linux-next.
- Fix memory leak in zcrypt
* tag 's390-5.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kaslr: add support for R_390_GLOB_DAT relocation type
s390/zcrypt: fix memleak at release
Linus Torvalds [Sat, 26 Oct 2019 10:26:04 +0000 (06:26 -0400)]
Merge tag 'dax-fix-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax fix from Dan Williams:
"Fix a performance regression that followed from a fix to the
conversion of the fsdax implementation to the xarray. v5.3 users
report that they stop seeing huge page mappings on an application +
filesystem layout that was seeing huge pages previously on v5.2"
* tag 'dax-fix-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
fs/dax: Fix pmd vs pte conflict detection
Linus Torvalds [Sat, 26 Oct 2019 00:11:33 +0000 (20:11 -0400)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
If we always compile the get_break_insn_length inline function we can
remove the ifdefs and let dead code elimination take care of the warn
branch that is now unreadable because the report_bug stub always
returns BUG_TRAP_TYPE_BUG.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Linus Torvalds [Fri, 25 Oct 2019 21:31:53 +0000 (17:31 -0400)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A fix for st1232 driver to properly report coordinates for 2nd and
subsequent fingers when more than one is on the surface"
Mike Christie [Thu, 17 Oct 2019 21:27:34 +0000 (16:27 -0500)]
nbd: verify socket is supported during setup
nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.
This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.
Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Tested-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
This driver is using regulator_get_optional() to handle all the supplies
that it handles, and only ever enables and disables all supplies en masse
without ever doing any other configuration of the device to handle missing
power. These are clear signs that the API is being misused - it should only
be used for supplies that may be physically absent from the system and in
these cases the hardware usually needs different configuration if the
supply is missing. Instead use normal regualtor_get(), if the supply is
not described in DT then the framework will substitute a dummy regulator in
so no special handling is needed by the consumer driver.
In the case of the PHY regulator the handling in the driver is a hack to
deal with integrated PHYs; the supplies are only optional in the sense
that that there's some confusion in the code about where they're bound to.
From a code point of view they function exactly as normal supplies so can
be treated as such. It'd probably be better to model this by instantiating
a PHY object for integrated PHYs.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
This was preceded by us timing out everything and shutting down the
sockets for the device. The problem is we had a request in the queue at
the same time, so we completed the request twice. This can actually
happen in a lot of cases, we fail to get a ref on our config, we only
have one connection and just error out the command, etc.
Fix this by checking cmd->status in nbd_read_stat. We only change this
under the cmd->lock, so we are safe to check this here and see if we've
already error'ed this command out, which would indicate that we've
completed it as well.
Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Josef Bacik [Mon, 21 Oct 2019 19:56:27 +0000 (15:56 -0400)]
nbd: protect cmd->status with cmd->lock
We already do this for the most part, except in timeout and clear_req.
For the timeout case we take the lock after we grab a ref on the config,
but that isn't really necessary because we're safe to touch the cmd at
this point, so just move the order around.
For the clear_req cause this is initiated by the user, so again is safe.
Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 25 Oct 2019 20:11:55 +0000 (16:11 -0400)]
Merge tag 'modules-for-v5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules fixes from Jessica Yu:
- Revert __ksymtab_$namespace.$symbol naming scheme back to
__ksymtab_$symbol, as it was causing issues with depmod.
Instead, have modpost extract a symbol's namespace from __kstrtabns
and __ksymtab_strings.
- Fix `make nsdeps` for out of tree kernel builds (make O=...) caused
by unescaped '/'.
Use a different sed delimiter to avoid this problem.
* tag 'modules-for-v5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: use alternative sed delimiter
symbol namespaces: revert to previous __ksymtab name scheme
modpost: make updating the symbol namespace explicit
modpost: delegate updating namespaces to separate function
Linus Torvalds [Fri, 25 Oct 2019 20:00:47 +0000 (16:00 -0400)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
Linus Torvalds [Fri, 25 Oct 2019 19:52:05 +0000 (15:52 -0400)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bugfixes for ARM, PPC and x86, plus selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: Don't leak L1 MMIO regions to L2
KVM: SVM: Fix potential wrong physical id in avic_handle_ldr_update
kvm: clear kvmclock MSR on reset
KVM: x86: fix bugon.cocci warnings
KVM: VMX: Remove specialized handling of unexpected exit-reasons
selftests: kvm: fix sync_regs_test with newer gccs
selftests: kvm: vmx_dirty_log_test: skip the test when VMX is not supported
selftests: kvm: consolidate VMX support checks
selftests: kvm: vmx_set_nested_state_test: don't check for VMX support twice
KVM: Don't shrink/grow vCPU halt_poll_ns if host side polling is disabled
selftests: kvm: synchronize .gitignore to Makefile
kvm: x86: Expose RDPID in KVM_GET_SUPPORTED_CPUID
KVM: arm64: pmu: Reset sample period on overflow handling
KVM: arm64: pmu: Set the CHAINED attribute before creating the in-kernel event
arm64: KVM: Handle PMCR_EL0.LC as RES1 on pure AArch64 systems
KVM: arm64: pmu: Fix cycle counter truncation
KVM: PPC: Book3S HV: XIVE: Ensure VP isn't already in use
Linus Torvalds [Fri, 25 Oct 2019 19:41:14 +0000 (15:41 -0400)]
Merge tag 'drm-fixes-2019-10-25' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Quiet week this week, which I suspect means some people just didn't
get around to sending me fixes pulls in time. This has 2 komeda and a
bunch of amdgpu fixes in it:
komeda:
- typo fixes
- flushing pipes fix
amdgpu:
- Fix suspend/resume issue related to multi-media engines
- Fix memory leak in user ptr code related to hmm conversion
- Fix possible VM faults when allocating page table memory
- Fix error handling in bo list ioctl"
* tag 'drm-fixes-2019-10-25' of git://anongit.freedesktop.org/drm/drm:
drm/komeda: Fix typos in komeda_splitter_validate
drm/komeda: Don't flush inactive pipes
drm/amdgpu/vce: fix allocation size in enc ring test
drm/amdgpu: fix error handling in amdgpu_bo_list_create
drm/amdgpu: fix potential VM faults
drm/amdgpu: user pages array memory leak fix
drm/amdgpu/vcn: fix allocation size in enc ring test
drm/amdgpu/uvd7: fix allocation size in enc ring test (v2)
drm/amdgpu/uvd6: fix allocation size in enc ring test (v2)
Linus Torvalds [Fri, 25 Oct 2019 19:25:51 +0000 (15:25 -0400)]
Merge tag 'mmc-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC host fixes:
- mxs: Fix flags passed to dmaengine_prep_slave_sg
- cqhci: Add a missing memory barrier
- sdhci-omap: Fix tuning procedure for temperatures < -20C"
* tag 'mmc-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: fix flags passed to dmaengine_prep_slave_sg
mmc: cqhci: Commit descriptors before setting the doorbell
mmc: sdhci-omap: Fix Tuning procedure for temperatures < -20C
Jens Axboe [Fri, 25 Oct 2019 16:06:15 +0000 (10:06 -0600)]
io_uring: fix bad inflight accounting for SETUP_IOPOLL|SETUP_SQTHREAD
We currently assume that submissions from the sqthread are successful,
and if IO polling is enabled, we use that value for knowing how many
completions to look for. But if we overflowed the CQ ring or some
requests simply got errored and already completed, they won't be
available for polling.
For the case of IO polling and SQTHREAD usage, look at the pending
poll list. If it ever hits empty then we know that we don't have
anymore pollable requests inflight. For that case, simply reset
the inflight count to zero.
Reported-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 25 Oct 2019 16:04:25 +0000 (10:04 -0600)]
io_uring: used cached copies of sq->dropped and cq->overflow
We currently use the ring values directly, but that can lead to issues
if the application is malicious and changes these values on our behalf.
Created in-kernel cached versions of them, and just overwrite the user
side when we update them. This is similar to how we treat the sq/cq
ring tail/head updates.
Reported-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Fri, 25 Oct 2019 09:31:31 +0000 (12:31 +0300)]
io_uring: Fix race for sqes with userspace
io_ring_submit() finalises with
1. io_commit_sqring(), which releases sqes to the userspace
2. Then calls to io_queue_link_head(), accessing released head's sqe
Reorder them.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Fri, 25 Oct 2019 09:31:30 +0000 (12:31 +0300)]
io_uring: Fix broken links with offloading
io_sq_thread() processes sqes by 8 without considering links. As a
result, links will be randomely subdivided.
The easiest way to fix it is to call io_get_sqring() inside
io_submit_sqes() as do io_ring_submit().
Downsides:
1. This removes optimisation of not grabbing mm_struct for fixed files
2. It submitting all sqes in one go, without finer-grained sheduling
with cq processing.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Alan Mikhak [Thu, 24 Oct 2019 16:11:43 +0000 (09:11 -0700)]
irqchip/sifive-plic: Skip contexts except supervisor in plic_init()
Modify plic_init() to skip .dts interrupt contexts other
than supervisor external interrupt.
The .dts entry for plic may specify multiple interrupt contexts.
For example, it may assign two entries IRQ_M_EXT and IRQ_S_EXT,
in that order, to the same interrupt controller. This patch
modifies plic_init() to skip the IRQ_M_EXT context since
IRQ_S_EXT is currently the only supported context.
If IRQ_M_EXT is not skipped, plic_init() will report "handler
already present for context" when it comes across the IRQ_S_EXT
context in the next iteration of its loop.
Without this patch, .dts would have to be edited to replace the
value of IRQ_M_EXT with -1 for it to be skipped.
Dave Airlie [Fri, 25 Oct 2019 04:48:53 +0000 (14:48 +1000)]
Merge tag 'drm-fixes-5.4-2019-10-23' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-10-23:
amdgpu:
- Fix suspend/resume issue related to multi-media engines
- Fix memory leak in user ptr code related to hmm conversion
- Fix possible VM faults when allocating page table memory
- Fix error handling in bo list ioctl
Dave Wysochanski [Wed, 23 Oct 2019 09:02:33 +0000 (05:02 -0400)]
cifs: Fix cifsInodeInfo lock_sem deadlock when reconnect occurs
There's a deadlock that is possible and can easily be seen with
a test where multiple readers open/read/close of the same file
and a disruption occurs causing reconnect. The deadlock is due
a reader thread inside cifs_strict_readv calling down_read and
obtaining lock_sem, and then after reconnect inside
cifs_reopen_file calling down_read a second time. If in
between the two down_read calls, a down_write comes from
another process, deadlock occurs.
Fix the above by changing all down_write(lock_sem) calls to
down_write_trylock(lock_sem)/msleep() loop, which in turn
makes the second down_read call benign since it will never
block behind the writer while holding lock_sem.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Suggested-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed--by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Pavel Shilovsky [Wed, 23 Oct 2019 22:37:19 +0000 (15:37 -0700)]
CIFS: Fix use after free of file info structures
Currently the code assumes that if a file info entry belongs
to lists of open file handles of an inode and a tcon then
it has non-zero reference. The recent changes broke that
assumption when putting the last reference of the file info.
There may be a situation when a file is being deleted but
nothing prevents another thread to reference it again
and start using it. This happens because we do not hold
the inode list lock while checking the number of references
of the file info structure. Fix this by doing the proper
locking when doing the check.
Fixes: 487317c99477d ("cifs: add spinlock for the openFileList to cifsInodeInfo") Fixes: cb248819d209d ("cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic") Cc: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Pavel Shilovsky [Tue, 22 Oct 2019 15:41:42 +0000 (08:41 -0700)]
CIFS: Fix retry mid list corruption on reconnects
When the client hits reconnect it iterates over the mid
pending queue marking entries for retry and moving them
to a temporary list to issue callbacks later without holding
GlobalMid_Lock. In the same time there is no guarantee that
mids can't be removed from the temporary list or even
freed completely by another thread. It may cause a temporary
list corruption:
Fix this by obtaining extra references for mids being retried
and marking them as MID_DELETED which indicates that such a mid
has been dequeued from the pending list.
Also move mid cleanup logic from DeleteMidQEntry to
_cifs_mid_q_entry_release which is called when the last reference
to a particular mid is put. This allows to avoid any use-after-free
of response buffers.
The patch needs to be backported to stable kernels. A stable tag
is not mentioned below because the patch doesn't apply cleanly
to any actively maintained stable kernel.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-and-tested-by: David Wysochanski <dwysocha@redhat.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Linus Torvalds [Thu, 24 Oct 2019 19:49:32 +0000 (15:49 -0400)]
Merge tag 'acpi-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix locking issue in the error code path of a function that belongs to
the sysfs interface exposed by the ACPI NFIT handling code (Dan
Carpenter)"
* tag 'acpi-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: NFIT: Fix unlock on error in scrub_show()
Linus Torvalds [Thu, 24 Oct 2019 19:36:11 +0000 (15:36 -0400)]
Merge tag 'pm-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix problems related to frequency limits management in cpufreq
that were introduced during the 5.3 cycle (when PM QoS had started to
be used for that), fix a few issues in the OPP (operating performance
points) library code and fix up the recently added haltpoll cpuidle
driver.
The cpufreq changes are somewhat bigger that I would like them to be
at this stage of the cycle, but the problems fixed by them include
crashes on boot and shutdown in some cases (among other things) and in
my view it is better to address the root of the issue right away.
Specifics:
- Using device PM QoS of CPU devices for managing frequency limits in
cpufreq does not work, so introduce frequency QoS (based on the
original low-level PM QoS) for this purpose, switch cpufreq and
related code over to using it and fix a race involving deferred
updates of frequency limits on top of that (Rafael Wysocki, Sudeep
Holla).
- Avoid calling regulator_enable()/disable() from the OPP framework
to avoid side-effects on boot-enabled regulators that may change
their initial voltage due to performing initial voltage balancing
without all restrictions from the consumers (Marek Szyprowski).
- Avoid a kref management issue in the OPP library code and drop an
incorrectly added lockdep_assert_held() from it (Viresh Kumar).
- Make the recently added haltpoll cpuidle driver take the 'idle='
override into account as appropriate (Zhenzhong Duan)"
* tag 'pm-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Reinitialize the list_kref before adding the static OPPs again
cpufreq: Cancel policy update work scheduled before freeing
cpuidle: haltpoll: Take 'idle=' override into account
opp: core: Revert "add regulators enable and disable"
PM: QoS: Drop frequency QoS types from device PM QoS
cpufreq: Use per-policy frequency QoS
PM: QoS: Introduce frequency QoS
opp: of: drop incorrect lockdep_assert_held()
Linus Torvalds [Thu, 24 Oct 2019 19:31:55 +0000 (15:31 -0400)]
Merge tag 'gfs2-v5.4-rc4.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Andreas Gruenbacher:
"Fix a memory leak introduced in -rc1"
* tag 'gfs2-v5.4-rc4.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix memory leak when gfs2meta's fs_context is freed
Fabrice Gasnier [Tue, 1 Oct 2019 08:51:09 +0000 (10:51 +0200)]
i2c: stm32f7: fix a race in slave mode with arbitration loss irq
When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
remains set until next master xfer (e.g. when STOPIE irq get unmasked).
In this case, completion is generated too early: immediately upon new
transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
stretches the SCL line: the bus gets busy until a future master transfer
triggers the bus busy / recovery mechanism (this can take time... and
may never happen at all)
So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.
i2c: stm32f7: fix first byte to send in slave mode
The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.
projects / linux.git / log