NeilBrown [Sat, 4 May 2019 10:24:57 +0000 (20:24 +1000)]
mmc: mtk-sd: enable internal card-detect logic.
The mtk-sd silicon has integrated card-detect logic that is
enabled on the MT7621. The circuit is phased out on newer hardware so
we should be careful to only enabled it on hardware known to support
it. This a new "use_internal_cd" flag in struct mtk_mmc_compatible.
If the sdhci isn't marked non-removable and doesn't have a
cd-gpio configured, and if use_internal_cd is set, then assume the
internal cd logic should be used as recommended by
Documentation/devicetree/bindings/mmc/mmc.txt
NeilBrown [Sat, 4 May 2019 10:24:56 +0000 (20:24 +1000)]
mmc: mtk-sd: don't hard-code interrupt trigger type
When using devicetree for configuration, interrupt trigger type
should be described in the dts file, not hard-coded in the C code.
The mtk-sd silicon in the mt7621 soc uses an active-high interrupt
and so cannot be used with the current code.
So replace IRQF_TRIGGER_LOW with IRQF_TRIGGER_NONE.
Also IRQF_ONESHOT is not needed - it is used for threaded interrupt
handlers, and this driver does not used a threaded interrupt handler.
So remove that setting.
Raul E Rangel [Thu, 2 May 2019 19:07:14 +0000 (13:07 -0600)]
mmc: core: Fix tag set memory leak
The tag set is allocated in mmc_init_queue but never freed. This results
in a memory leak. This change makes sure we free the tag set when the
queue is also freed.
mmc: mmci: Prevent polling for busy detection in IRQ context
The IRQ handler, mmci_irq(), loops until all status bits have been cleared.
However, the status bit signaling busy in variant->busy_detect_flag, may be
set even if busy detection isn't monitored for the current request.
This may be the case for the CMD11 when switching the I/O voltage, which
leads to that mmci_irq() busy loops in IRQ context. Fix this problem, by
clearing the status bit for busy, before continuing to validate the
condition for the loop. This is safe, because the busy status detection has
already been taken care of by mmci_cmd_irq().
mmc: usdhi6rol0: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
In file included from drivers/mmc/host/usdhi6rol0.c:9:
drivers/mmc/host/usdhi6rol0.c: In function ‘usdhi6_timeout_work’:
./include/linux/device.h:1483:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/usdhi6rol0.c:1689:3: note: in expansion of macro ‘dev_err’
dev_err(mmc_dev(host->mmc), "Invalid state %u\n", host->wait);
^~~~~~~
drivers/mmc/host/usdhi6rol0.c:1691:2: note: here
case USDHI6_WAIT_FOR_CMD:
^~~~
drivers/mmc/host/usdhi6rol0.c:1711:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
usdhi6_sg_unmap(host, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/usdhi6rol0.c:1716:2: note: here
case USDHI6_WAIT_FOR_DATA_END:
^~~~
CC [M] drivers/isdn/hisax/hisax_isac.o
drivers/mmc/host/usdhi6rol0.c: In function ‘usdhi6_stop_cmd’:
drivers/mmc/host/usdhi6rol0.c:1338:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (mrq->stop->opcode == MMC_STOP_TRANSMISSION) {
^
drivers/mmc/host/usdhi6rol0.c:1343:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD Physical Layer Spec says the following: Since the SD Memory Card
shall support at least the two bus modes 1-bit or 4-bit width, then any SD
Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").
This change verifies the card has specified a bus width.
AMD SDHC Device 7806 can get into a bad state after a card disconnect
where anything transferred via the DATA lines will always result in a
zero filled buffer. Currently the driver will continue without error if
the HC is in this condition. A block device will be created, but reading
from it will result in a zero buffer. This makes it seem like the SD
device has been erased, when in actuality the data is never getting
copied from the DATA lines to the data buffer.
SCR is the first command in the SD initialization sequence that uses the
DATA lines. By checking that the response was invalid, we can abort
mounting the card.
mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
Add HS400 support for iMX7ULP B0.
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle
On some SoCs such as i.MX7ULP, there is no busfreq
driver, but cpuidle has some levels which may disable
system/bus clocks, so need to add pm_qos to prevent
cpuidle from entering low level idles and make sure
system/bus clocks are enabled when usdhc is active.
Use signal resampling tuning for the UHS and HS200 modes.
Instead of trying to get the *best* resampling setting with complex
window calculation, we just stop on the first working setting.
If the tuning setting later proves unstable, we will just continue the
tuning where we left it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This remove all the code related to phase settings. Using the Rx phase
for tuning has not been reliable. We had several issues over the past
months, on both v2 and v3 mmc chips After discussing the issue matter
with Amlogic, They suggested to set a phase shift of 180 between Core and
Tx and use signal resampling for the tuning.
Since we won't be playing with the phase anymore, let's remove all the
clock code related to it and set the appropriate value on init.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: meson-gx: avoid clock glitch when switching to DDR modes
Activating DDR in the Amlogic mmc controller, among other things, will
divide the output clock by 2. So by activating it with clock on, we are
creating a glitch on the output.
Instead, let's deal with DDR when the clock output is off, when setting
the clock.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the moment, all our attempts to enable HS400 on Amlogic chipsets have
been unsuccessful or unreliable. Until we can figure out how to enable this
mode safely and reliably, let's force it off.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason for another device to request the MMC irq. It should
only be used the MMC device, so remove IRQ_SHARED and replace by
IRQ_ONESHOT as we don't the irq to fire again until the irq thread is
done
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Drake [Mon, 29 Apr 2019 05:14:26 +0000 (13:14 +0800)]
mmc: alcor: work with multiple-entry sglists
DMA on this hardware is limited to dealing with a 4096 bytes at a
time. Previously, the driver was set up accordingly to request single-page
DMA buffers, however that had the effect of generating a large number
of small MMC requests for data I/O.
Improve the driver to accept multi-entry scatter-gather lists. The size of
each entry is already capped to 4096 bytes (AU6601_MAX_DMA_BLOCK_SIZE),
matching the hardware requirements. Existing driver code already iterates
through remaining sglist entries after each DMA transfer is complete.
Also add some comments to help clarify the situation, and clear up
some of the confusion I had regarding DMA vs PIO.
Testing with dd, this increases write performance from 2mb/sec to
10mb/sec, and increases read performance from 4mb/sec to 14mb/sec.
Usage of the DMA page iterator was problematic here because
we were not considering offset & length of entries in the scatterlist.
Also, after further discussion, the suggested revised approach is much
more similar to the driver implementation before this commit was
applied, so revert it.
Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
memstick: tifm: remove set but not used variable 'data'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/memstick/host/tifm_ms.c: In function 'tifm_ms_issue_cmd':
drivers/memstick/host/tifm_ms.c:259:17: warning:
variable 'data' set but not used [-Wunused-but-set-variable]
It's not used any more since commit 92b22d935fed ("tifm: fix the
MemoryStick host fifo handling code")
Pan Bian [Wed, 17 Apr 2019 08:28:37 +0000 (16:28 +0800)]
mmc: core: fix possible use after free of host
In the function mmc_alloc_host, the function put_device is called to
release allocated resources when mmc_gpio_alloc fails. Finally, the
function pointed by host->class_dev.class->dev_release (i.e.,
mmc_host_classdev_release) is used to release resources including the
host structure. However, after put_device, host is used and released
again. Resulting in a use-after-free bug.
Fixes: 1ed217194488 ("mmc: core: fix error path in mmc_host_alloc") Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* pm-devfreq:
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
PM / devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.
PM / devfreq: rockchip-dfi: Move GRF definitions to a common place.
PM / devfreq: exynos-bus: Suspend all devices on system shutdown
PM / devfreq: Fix static checker warning in try_then_request_governor
PM / devfreq: Restart previous governor if new governor fails to start
PM / devfreq: tegra: remove unneeded variable
PM / devfreq: rockchip-dfi: remove unneeded semicolon
PM / devfreq: rk3399_dmc: remove unneeded semicolon
PM / devfreq: consistent indentation
PM / devfreq: fix missing check of return value in devfreq_add_device()
PM / devfreq: fix mem leak in devfreq_add_device()
PM / devfreq: Use of_node_name_eq for node name comparisons
* pm-domains:
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
PM / Domains: remove unnecessary unlikely()
* pm-misc:
firmware/psci: add support for SYSTEM_RESET2
drivers: firmware: psci: Announce support for OS initiated suspend mode
drivers: firmware: psci: Simplify error path of psci_dt_init()
drivers: firmware: psci: Split psci_dt_cpu_init_idle()
MAINTAINERS: Update files for PSCI
drivers: firmware: psci: Move psci to separate directory
* pm-cpuidle:
PM / Domains: Add genpd governor for CPUs
cpuidle: Export the next timer expiration for CPUs
PM / Domains: Add support for CPU devices to genpd
PM / Domains: Add generic data pointer to struct genpd_power_state
cpuidle: exynos: Unify target residency for AFTR and coupled AFTR states
* pm-sleep:
PM / core: Propagate dev->power.wakeup_path when no callbacks
PM / core: Introduce dpm_async_fn() helper
PM / core: fix kerneldoc comment for device_pm_wait_for_dev()
PM / core: fix kerneldoc comment for dpm_watchdog_handler()
PM / sleep: Measure the time of filesystems syncing
PM / sleep: Refactor filesystems sync to reduce duplication
PM / wakeup: Use pm_pr_dbg() instead of pr_debug()
* acpi-doc: (25 commits)
Documentation: ACPI: move video_extension.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move ssdt-overlays.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move lpit.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move cppc_sysfs.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move apei/einj.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move apei/output_format.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move aml-debugger.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move method-tracing.txt to firmware-guide/acpi and convert to rsST
Documentation: ACPI: move debug.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/data-node-references.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/graph.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move acpi-lid.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move i2c-muxes.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsdt-override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move initrd_table_override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move method-customizing.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move gpio-properties.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move DSD-properties-rules.txt to firmware-guide/acpi and covert to reST
Documentation: ACPI: move scan_handlers.txt to driver-api/acpi and convert to reST
Documentation: ACPI: move linuxized-acpica.txt to driver-api/acpi and convert to reST
...
Merge branches 'acpi-utils', 'acpi-video', 'acpi-soc' and 'acpi-button'
* acpi-utils:
gpio: merrifield: Fix build err without CONFIG_ACPI
ACPI / utils: Remove deprecated function since no user left
ASoC: Intel: cht_bsw_rt5672: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: cht_bsw_rt5645: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcr_rt5651: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcr_rt5640: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcht_es8316: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcht_da7213: Convert to use acpi_dev_get_first_match_dev()
gpio: merrifield: Convert to use acpi_dev_get_first_match_dev()
extcon: axp288: Convert to use acpi_dev_get_first_match_dev()
ACPI / utils: Introduce acpi_dev_get_first_match_dev() helper
* acpi-video:
ACPI: video: Use vendor backlight on Sony VPCEH3U1E
* acpi-soc:
ACPI / LPSS: Use acpi_lpss_* instead of acpi_subsys_* functions for hibernate
* acpi-button:
ACPI: button: reinitialize button state upon resume
* acpica:
ACPICA: Update version to 20190405
ACPICA: Namespace: add check to avoid null pointer dereference
ACPICA: Update version to 20190329
ACPICA: utilities: fix spelling of PCC to platform_comm_channel
ACPICA: Rename nameseg length macro/define for clarity
ACPICA: Rename nameseg compare macro for clarity
ACPICA: Rename nameseg copy macro for clarity
Andrii Nakryiko [Mon, 6 May 2019 00:10:33 +0000 (17:10 -0700)]
kbuild: tolerate missing pahole when generating BTF
When BTF generation is enabled through CONFIG_DEBUG_INFO_BTF,
scripts/link-vmlinux.sh detects if pahole version is too old and
gracefully continues build process, skipping BTF generation build step.
But if pahole is not available, build will still fail. This patch adds
check for whether pahole exists at all and bails out gracefully, if not.
Cc: Alexei Starovoitov <ast@fb.com> Reported-by: Yonghong Song <yhs@fb.com> Fixes: e83b9f55448a ("kbuild: add ability to generate BTF type info for vmlinux") Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
x86/fpu: Fault-in user stack if copy_fpstate_to_sigframe() fails
In the compacted form, XSAVES may save only the XMM+SSE state but skip
FP (x87 state).
This is denoted by header->xfeatures = 6. The fastpath
(copy_fpregs_to_sigframe()) does that but _also_ initialises the FP
state (cwd to 0x37f, mxcsr as we do, remaining fields to 0).
The slowpath (copy_xstate_to_user()) leaves most of the FP
state untouched. Only mxcsr and mxcsr_flags are set due to
xfeatures_mxcsr_quirk(). Now that XFEATURE_MASK_FP is set
unconditionally, see
04944b793e18 ("x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext"),
on return from the signal, random garbage is loaded as the FP state.
Instead of utilizing copy_xstate_to_user(), fault-in the user memory
and retry the fast path. Ideally, the fast path succeeds on the second
attempt but may be retried again if the memory is swapped out due
to memory pressure. If the user memory can not be faulted-in then
get_user_pages() returns an error so we don't loop forever.
Fault in memory via get_user_pages_unlocked() so
copy_fpregs_to_sigframe() succeeds without a fault.
Fixes: 69277c98f5eef ("x86/fpu: Always store the registers in copy_fpstate_to_sigframe()") Reported-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de> Suggested-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Hansen <dave.hansen@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jann Horn <jannh@google.com> Cc: "linux-mm@kvack.org" <linux-mm@kvack.org> Cc: Qian Cai <cai@lca.pw> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190502171139.mqtegctsg35cir2e@linutronix.de
Dan Carpenter [Tue, 23 Apr 2019 10:40:20 +0000 (13:40 +0300)]
i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
The problem here is that addr can be I3C_BROADCAST_ADDR (126). That
means we're shifting by (126 * 2) % 64 which is 60. The
I3C_ADDR_SLOT_STATUS_MASK is an enum which is an unsigned int in GCC
so shifts greater than 31 are undefined.
Fixes: 3a379bbcea0a ("i3c: Add core I3C infrastructure") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
====================
r8169: replace some magic with more speaking functions
Based on info from Realtek replace some magic with speaking functions
even though the exact meaning of certain values isn't known.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset from Jiri allows users to enable loopback feature for
individual ports using ethtool. The loopback feature is useful for
testing purposes and will also be used by upcoming patchsets to enable
the monitoring of buffer drops.
Patch #1 adds the relevant device register.
Patch #2 Implements support in the driver.
Patch #3 adds a selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 4 May 2019 18:43:42 +0000 (11:43 -0700)]
sch_htb: redefine htb qdisc overlimits
In commit 3c75f6ee139d ("net_sched: sch_htb: add per class overlimits counter")
we added an overlimits counter for each HTB class which could
properly reflect how many times we use up all the bandwidth
on each class. However, the overlimits counter in HTB qdisc
does not, it is way bigger than the sum of each HTB class.
In fact, this qdisc overlimits counter increases when we have
no skb to dequeue, which happens more often than we run out of
bandwidth.
It makes more sense to make this qdisc overlimits counter just
be a sum of each HTB class, in case people still get confused.
I have verified this patch with one single HTB class, where HTB
qdisc counters now always match HTB class counters as expected.
Eric suggested we could fold this field into 'direct_pkts' as
we only use its 32bit on 64bit CPU, this saves one cache line.
Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Traffic support for SJA1105 DSA driver
This patch set is a continuation of the "NXP SJA1105 DSA driver" v3
series, which was split in multiple pieces for easier review.
Supporting a fully-featured (traffic-capable) driver for this switch
requires some rework in DSA and also leaves behind a more generic
infrastructure for other dumb switches that rely on 802.1Q pseudo-switch
tagging for port separation. Among the DSA changes required are:
* Generic xmit and rcv functions for pushing/popping 802.1Q tags on
skb's. These are modeled as a tagging protocol of its own but which
must be customized by drivers to fit their own hardware possibilities.
* Permitting the .setup callback to invoke switchdev operations that
will loop back into the driver through the switchdev notifier chain.
The SJA1105 driver then proceeds to extend this 8021q switch tagging
protocol while adding its own (tag_sja1105). This is done because
the driver actually implements a "dual tagger":
* For normal traffic it uses 802.1Q tags
* For management (multicast DMAC) frames the switch has native support
for recognizing and annotating these with source port and switch id
information.
Because this is a "dual tagger", decoding of management frames should
still function when regular traffic can't (under a bridge with VLAN
filtering).
There was intervention in the DSA receive hotpath, where a new
filtering function called from eth_type_trans() is needed. This is
useful in the general sense for switches that might actually have some
limited means of source port decoding, such as only for management
traffic, but not for everything.
In order for the 802.1Q tagging protocol (which cannot be enabled under
all conditions, unlike the management traffic decoding) to not be an
all-or-nothing choice, the filtering function matches everything that
can be decoded, and everything else is left to pass to the master
netdevice.
Lastly, DSA core support was added for drivers to request skb deferral.
SJA1105 needs this for SPI intervention during transmission of link-local
traffic. This is not done from within the tagger.
Some patches were carried over unchanged from the previous patchset
(01/09). Others were slightly reworked while adapting to the recent
changes in "Make DSA tag drivers kernel modules" (02/09).
The introduction of some structures (DSA_SKB_CB, dp->priv) may seem a
little premature at this point and the new structures under-utilized.
The reason is that traffic support has been rewritten with PTP
timestamping in mind, and then I removed the timestamping code from the
current submission (1. it is a different topic, 2. it does not work very
well yet). On demand I can provide the timestamping patchset as a RFC
though.
"NXP SJA1105 DSA driver" v3 patchset can be found at:
https://lkml.org/lkml/2019/4/12/978
v1 patchset can be found at:
https://lkml.org/lkml/2019/5/3/877
Changes in v2:
* Made the deferred xmit workqueue also be drained on the netdev suspend
callback, not just on ndo_stop.
* Added clarification about how other netdevices may be bridged with the
switch ports.
v2 patchset can be found at:
https://www.spinics.net/lists/netdev/msg568818.html
Changes in v3:
* Exported the dsa_port_vid_add and dsa_port_vid_del symbols to fix an
error reported by the kbuild test robot
* Fixed the following checkpatch warnings in 05/10:
Macro argument reuse 'skb' - possible side-effects?
Macro argument reuse 'clone' - possible side-effects?
* Added a commit description to the documentation patch (10/10)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:29 +0000 (13:19 +0300)]
Documentation: net: dsa: sja1105: Add info about supported traffic modes
This adds a table which illustrates what combinations of management /
regular traffic work depending on the state the switch ports are in.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:28 +0000 (13:19 +0300)]
net: dsa: sja1105: Add support for Spanning Tree Protocol
While not explicitly documented as supported in UM10944, compliance with
the STP states can be obtained by manipulating 3 settings at the
(per-port) MAC config level: dynamic learning, inhibiting reception of
regular traffic, and inhibiting transmission of regular traffic.
In all these modes, transmission and reception of special BPDU frames
from the stack is still enabled (not inhibited by the MAC-level
settings).
On ingress, BPDUs are classified by the MAC filter as link-local
(01-80-C2-00-00-00) and forwarded to the CPU port. This mechanism works
under all conditions (even without the custom 802.1Q tagging) because
the switch hardware inserts the source port and switch ID into bytes 4
and 5 of the MAC-filtered frames. Then the DSA .rcv handler needs to put
back zeroes into the MAC address after decoding the source port
information.
On egress, BPDUs are transmitted using management routes from the xmit
worker thread. Again this does not require switch tagging, as the switch
port is programmed through SPI to hold a temporary (single-fire) route
for a frame with the programmed destination MAC (01-80-C2-00-00-00).
STP is activated using the following commands and was tested by
connecting two front-panel ports together and noticing that switching
loops were prevented (one port remains in the blocking state):
$ ip link add name br0 type bridge stp_state 1 && ip link set br0 up
$ for eth in $(ls /sys/devices/platform/soc/2100000.spi/spi_master/spi0/spi0.1/net/);
do ip link set ${eth} master br0 && ip link set ${eth} up; done
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:27 +0000 (13:19 +0300)]
net: dsa: sja1105: Add support for traffic through standalone ports
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:26 +0000 (13:19 +0300)]
net: dsa: Add a private structure pointer to dsa_port
This is supposed to share information between the driver and the tagger,
or used by the tagger to keep some state. Its use is optional.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:25 +0000 (13:19 +0300)]
net: dsa: Add support for deferred xmit
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:24 +0000 (13:19 +0300)]
net: dsa: Keep private info in the skb->cb
Map a DSA structure over the 48-byte control block that will hold
skb info on transmit and receive. This is only for use within the DSA
processing layer (e.g. communicating between DSA core and tagger) and
not for passing info around with other layers such as the master net
device.
Also add a DSA_SKB_CB_PRIV() macro which retrieves a pointer to the
space up to 48 bytes that the DSA structure does not use. This space can
be used for drivers to add their own private info.
One use is for the PTP timestamping code path. When cloning a skb,
annotate the original with a pointer to the clone, which the driver can
then find easily and place the timestamp to. This avoids the need of a
separate queue to hold clones and a way to match an original to a cloned
skb.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:23 +0000 (13:19 +0300)]
net: dsa: Allow drivers to filter packets they can decode source port from
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:22 +0000 (13:19 +0300)]
net: dsa: Optional VLAN-based port separation for switches without tagging
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:21 +0000 (13:19 +0300)]
net: dsa: Export symbols for dsa_port_vid_{add, del}
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 5 May 2019 10:19:20 +0000 (13:19 +0300)]
net: dsa: Call driver's setup callback after setting up its switchdev notifier
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>- Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 May 2019 23:28:22 +0000 (19:28 -0400)]
net: dsa: mv88e6xxx: refine SMI support
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 May 2019 04:49:24 +0000 (21:49 -0700)]
Merge branch 'net-act_police-offload-support'
Jakub Kicinski says:
===================
net: act_police offload support
this set starts by converting cls_matchall to the new flow offload
infrastructure. It so happens that all drivers implementing cls_matchall
offload today also offload cls_flower, so its a little easier for
them to handle the actions in unified flow_rule format, even though
in cls_matchall there is no flow to speak of. If a driver ever appears
which would prefer the old, direct access to TC exts, we can add the
pointer in the offload structure back and support both.
Next the act_police is added to actions supported by flow offload API.
NFP support for act_police offload is added as the final step. The flower
firmware is configured to perform TX rate limiting in a way which matches
act_police's behaviour. It does not use DMA.IN back pressure, and
instead drops packets after they had been already DMAed into the NIC.
IOW it uses our standard traffic policing implementation, future patches
will extend it to other ports and traffic directions.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: add qos offload stats request and reply
Add stats request function that sends a stats request message to hw for
a specific police-filter. Process stats reply from hw and update the
stored qos structure.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: add qos offload install and remove functionality.
Add install and remove offload functionality for qos offloads. We
first check that a police filter can be implemented by the VF rate
limiting feature in hw, then we install the filter via the qos
infrastructure. Finally we implement the mechanism for removing
these types of filters.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce matchall filter offload infrastructure that is needed to
offload qos features like policing. Subsequent patches will make
use of police-filters for ingress rate limiting.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: add block pointer to tc_cls_common_offload structure
Some actions like the police action are stateful and could share state
between devices. This is incompatible with offloading to multiple devices
and drivers might want to test for shared blocks when offloading.
Store a pointer to the tcf_block structure in the tc_cls_common_offload
structure to allow drivers to determine when offloads apply to a shared
block.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: allow stats updates from offloaded police actions
Implement the stats_update callback for the police action that
will be used by drivers for hardware offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: extend matchall offload for hardware statistics
Introduce a new command for matchall classifiers that allows hardware
to update statistics.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: add police action to the hardware intermediate representation
Add police action to the hardware intermediate representation which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: move police action structures to header
Move tcf_police_params, tcf_police and tc_police_compat structures to a
header. Making them usable to other code for example drivers that would
offload police actions to hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: remove unused functions for matchall offload
Cleanup unused functions and variables after porting to the newer
intermediate representation.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa: use intermediate representation for matchall offload
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: use intermediate representation for matchall offload
Updates the Mellanox spectrum driver to use the newer intermediate
representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: use the hardware intermediate representation for matchall
Extends matchall offload to make use of the hardware intermediate
representation. More specifically, this patch moves the native TC
actions in cls_matchall offload to the newer flow_action
representation. This ultimately allows us to avoid a direct
dependency on native TC actions for matchall.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: add sample action to the hardware intermediate representation
Add sample action to the hardware intermediate representation model which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
of_net: Add NVMEM support to of_get_mac_address
this patch series is a continuation of my previous attempt[1], where I've
tried to wire MTD layer into of_get_mac_address, so it would be possible to
load MAC addresses from various NVMEMs as EEPROMs etc.
Predecessor of this patch which used directly MTD layer has originated in
OpenWrt some time ago and supports already about 497 use cases in 357
device tree files.
During the review process of my 1st attempt I was told, that I shouldn't be
using MTD directly, but that I should rather use new NVMEM subsystem and
during the review process of v2 I was told, that I should handle
EPROBE_DEFFER error as well, during the review process of v3 I was told,
that returning pointer/NULL/ERR_PTR is considered as wrong API design, so
this v4 patch series tries to accommodate all this previous remarks.
First patch is wiring NVMEM support directly into of_get_mac_address as
it's obvious, that adding support for NVMEM into every other driver would
mean adding a lot of repetitive code. This patch allows us to configure MAC
addresses in various devices like ethernet and wireless adapters directly
from of_get_mac_address, which is used by quite a lot of drivers in the
tree already.
Second patch is simply updating documentation with NVMEM bits, and cleaning
up all current binding documentation referencing any of the MAC address
related properties.
Third and fourth patches are simply removing duplicate NVMEM code which is
no longer needed as the first patch has wired NVMEM support directly into
of_get_mac_address.
Patches 5-10 are converting all current users of of_get_mac_address to the
new ERR_PTR encoded error value, as of_get_mac_address could now return
valid pointer, NULL and ERR_PTR.
Just for a better picture, this patch series and one simple patch[2] on top
of it, allows me to configure 8Devices Carambola2 board's MAC addresses
with following DTS (simplified):
Petr Štetiar [Fri, 3 May 2019 14:27:15 +0000 (16:27 +0200)]
powerpc: tsi108: support of_get_mac_address new ERR_PTR error
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:14 +0000 (16:27 +0200)]
ARM: Kirkwood: support of_get_mac_address new ERR_PTR error
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:13 +0000 (16:27 +0200)]
staging: octeon-ethernet: support of_get_mac_address new ERR_PTR error
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:12 +0000 (16:27 +0200)]
net: wireless: support of_get_mac_address new ERR_PTR error
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:11 +0000 (16:27 +0200)]
net: usb: support of_get_mac_address new ERR_PTR error
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:09 +0000 (16:27 +0200)]
net: davinci: support of_get_mac_address new ERR_PTR error
There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:08 +0000 (16:27 +0200)]
net: macb: support of_get_mac_address new ERR_PTR error
There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:07 +0000 (16:27 +0200)]
dt-bindings: doc: reflect new NVMEM of_get_mac_address behaviour
As of_get_mac_address now supports NVMEM under the hood, we need to update
the bindings documentation with the new nvmem-cell* properties, which would
mean copy&pasting a lot of redundant information to every binding
documentation currently referencing some of the MAC address properties.
So I've just removed all the references to the optional MAC address
properties and replaced them with the small note referencing
net/ethernet.txt file.
Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Štetiar [Fri, 3 May 2019 14:27:06 +0000 (16:27 +0200)]
of_net: add NVMEM support to of_get_mac_address
Many embedded devices have information such as MAC addresses stored
inside NVMEMs like EEPROMs and so on. Currently there are only two
drivers in the tree which benefit from NVMEM bindings.
Adding support for NVMEM into every other driver would mean adding a lot
of repetitive code. This patch allows us to configure MAC addresses in
various devices like ethernet and wireless adapters directly from
of_get_mac_address, which is already used by almost every driver in the
tree.
Predecessor of this patch which used directly MTD layer has originated
in OpenWrt some time ago and supports already about 497 use cases in 357
device tree files.
Cc: Alban Bedel <albeu@free.fr> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 May 2019 04:42:17 +0000 (21:42 -0700)]
Merge branch 'bnxt_en-Driver-updates'
Michael Chan says:
====================
bnxt_en: Driver updates.
This patch series adds some extended statistics available with the new
firmware interface, package version from firmware, aRFS support on
57500 chips, new PCI IDs, and some miscellaneous fixes and improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 5 May 2019 11:17:05 +0000 (07:17 -0400)]
bnxt_en: Improve NQ reservations.
bnxt_need_reserve_rings() determines if any resources have changed and
requires new reservation with firmware. The NQ checking is currently
just an approximation. Improve the NQ checking logic to make it
accurate. NQ reservation is only needed on 57500 PFs. This fix will
eliminate unnecessary reservations and will reduce NQ reservations
when some NQs have been released on 57500 PFs.
Fixes: c0b8cda05e1d ("bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Devesh Sharma [Sun, 5 May 2019 11:17:04 +0000 (07:17 -0400)]
bnxt_en: Separate RDMA MR/AH context allocation.
In newer firmware, the context memory for MR (Memory Region)
and AH (Address Handle) to support RDMA are specified separately.
Modify driver to specify and allocate the 2 context memory types
separately when supported by the firmware.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver hard code Clause 45 based on speed supported by the
PHY. Instead read the clause type from the PHY ID provided as input
to the mdio ioctl.
Fixes: 0ca12be99667 ("bnxt_en: Add support for mdio read/write to external PHY") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
HWRM_VER_GET firmware command returns package name that is running
actively on the adapter. Use this version instead of parsing from
the package log in NVRAM.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Check new firmware capability to display extended stats.
Newer firmware now advertises the capability for extended stats
support. Check the new capability in addition to the existing
version check.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reverse the condition of the large "if" block and return early. This
will simplify the follow up patch to add PCIe statistics.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 May 2019 04:40:23 +0000 (21:40 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-05-04
This series contains updates to the ice driver only.
Jesse updated the driver to make more functions consistent in their use
of a local variable for vsi->back. Updates the driver to use bit fields
when possible to avoid wasting lots of storage space to store single bit
values. Optimized the driver to be more memory efficient by moving
structure members around that are not in are hot path.
Michal updates the driver to disable the VF if malicious device driver
(MDD) event is detected by the hardware. Adds checks to validate the
messages coming from the VF driver. Tightens up the sniffing of the
driver so that transmit traffic so that VF's cannot see what is on other
VSIs.
Tony fixed the driver so that receive stripping state won't change every
time transmit insertion is changed. Cleanup the __always_unused
attribute, now that the variable is being used. Fixed the function
which evaluates setting of features to ensure that can evaluate and set
multiple features in a single function call.
Akeem fixes the driver so that we do not attempt to remove a VLAN filter
that does not exist. Adds support for adding a ethertype based filter
rule on VSI and describe it in a very long run-on sentence. :-)
Bruce cleans up static analysis warnings by removing a local variable
initialization that is not needed.
Brett makes the allocate/deallocate more consistent in all the driver
flows for VSI q_vectors. In addition, makes setting/getting coalesce
settings more consistent throughout the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 May 2019 04:38:25 +0000 (21:38 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-05-04
This series contains updates to i40e only.
Grzegorz fixes a bug with promiscuous mode not being kept when the VF
switched to a new VLAN. Fixed a typo in the link mode code, by using
the correct define. Fixed truncation issue, which changed an function
argument to a smaller value that should have been a larger value.
Aleksandr adds support for new x710 devices and the speeds they support.
Sergey adds a check for the number of vectors against the number of MSIx
vectors to ensure one does not exceed the other.
Martyna adds additional input validation on VF messages handled by the
PF. Fixed potential memory leaks in the driver where the error paths
were not freeing allocated memory.
Maciej reverts the double ShadowRAM checksum calculation change because
issues were found in the NVM downgrade situation.
Gustavo Silva changes the i40e driver to use struct_size() in kzalloc()
calls, to avoid type mistakes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log