Olof Johansson [Sat, 2 Nov 2019 20:29:36 +0000 (13:29 -0700)]
Merge tag 'sunxi-fixes-for-5.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
One fix for the A83t powerdown, and one for the TBS A711 tablet wifi suspend
* tag 'sunxi-fixes-for-5.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
Olof Johansson [Sat, 2 Nov 2019 20:28:56 +0000 (13:28 -0700)]
Merge tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 2nd round:
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da5d ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
* tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
Ondrej Jirman [Mon, 28 Oct 2019 21:49:14 +0000 (22:49 +0100)]
ARM: sunxi: Fix CPU powerdown on A83T
PRCM_PWROFF_GATING_REG has CPU0 at bit 4 on A83T. So without this
patch, instead of gating the CPU0, the whole cluster was power gated,
when shutting down first CPU in the cluster.
Fixes: 6961275e72a8c1 ("ARM: sun8i: smp: Add support for A83T") Signed-off-by: Ondrej Jirman <megous@megous.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Cc: stable@vger.kernel.org Signed-off-by: Maxime Ripard <mripard@kernel.org>
Olof Johansson [Mon, 28 Oct 2019 15:20:05 +0000 (08:20 -0700)]
Merge tag 'reset-fixes-for-v5.5' of git://git.pengutronix.de/git/pza/linux into arm/fixes
Reset controller fixes for v5.5
This tag fixes a memory leak in reset_control_array_put(), which is
called by reset_control_put() for reset array controls. The other
patches are small kerneldoc comment fixes to avoid documentation build
warnings.
Randy Dunlap [Wed, 23 Oct 2019 03:57:06 +0000 (20:57 -0700)]
reset: fix reset_control_ops kerneldoc comment
Add a missing short description to the reset_control_ops documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[p.zabel@pengutronix.de: rebased and updated commit message] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adam Ford [Wed, 16 Oct 2019 14:40:05 +0000 (09:40 -0500)]
ARM: dts: imx6-logicpd: Re-enable SNVS power key
The baseboard of the Logic PD i.MX6 development kit has a power
button routed which can both power down and power up the board.
It can also wake the board from sleep. This functionality was
marked as disabled by default in imx6qdl.dtsi, so it needs to
be explicitly enabled for each board.
This patch enables the snvs power key again.
Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design") Cc: stable <stable@vger.kernel.org> #5.3+ Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.
The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.
The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.
Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.
Yuantian Tang [Thu, 10 Oct 2019 08:33:34 +0000 (16:33 +0800)]
arm64: dts: ls1028a: fix a compatible issue
The I2C multiplexer used on ls1028aqds is PCA9547, not PCA9847.
If the wrong compatible was used, this chip will not be able to
be probed correctly and hence fail to work.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing parentheses to correctly hyperlink the reference to
reset_control_get_shared().
Fixes: 0b52297f2288 ("reset: Add support for shared reset controls") Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a newline and remove a superfluous kerneldoc marker before the
of_reset_control_get_count kerneldoc comment, to fix documentation
build warnings:
./drivers/reset/core.c:832: warning: Incorrect use of kernel-doc format: * of_reset_control_get_count - Count number of resets available with a device
./drivers/reset/core.c:840: warning: Function parameter or member 'node' not described in 'of_reset_control_get_count'
Fixes: 17c82e206d2a ("reset: Add APIs to manage array of resets") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Olof Johansson [Thu, 24 Oct 2019 03:01:24 +0000 (20:01 -0700)]
Merge tag 'arm-soc/for-5.5/maintainers' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains MAINTAINERS file updates for Broadcom SoCs
for the 5.5 kernel, please pull the following:
- Simon adds a .mailmap alias for his old email
- Stefan updates the existing BCM2835 with BCM2711 which is the chip
name for the Raspberry Pi 4
- Florian removes Gregory and Brian from the MAINTAINERS file for
BRCMSTB SoCs
* tag 'arm-soc/for-5.5/maintainers' of https://github.com/Broadcom/stblinux:
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
mailmap: Add Simon Arlott (replacement for expired email address)
MAINTAINERS: Add BCM2711 to BCM2835 ARCH
Florian Fainelli [Fri, 18 Oct 2019 17:18:35 +0000 (10:18 -0700)]
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
The last time Gregory and Brian did a review was sometime around 2015,
since then, they have not been active for ARCH_BRCMSTB changes.
Following the position of other maintainers and Harald Welte's position
here:
Olof Johansson [Wed, 23 Oct 2019 17:08:11 +0000 (10:08 -0700)]
Merge tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Three fixes for omaps for v5.4-rc cycle
Two regression fixes for omap3 iommu. I missed applying two omap3
related iommu pdata quirks patches earlier because the kbuild test
robot produced errors on them for missing dependencies.
Fix ti-sysc interconnect target module driver handling for watchdog
quirk. I must have tested this earlier only with watchdog service
running, but clearly it does not do what it needs to do.
* tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
Olof Johansson [Wed, 23 Oct 2019 15:34:08 +0000 (08:34 -0700)]
Merge tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
reset: Fix memory leak in reset_control_array_put()
Memory allocated for 'struct reset_control_array' in
of_reset_control_array_get() is never freed in
reset_control_array_put() resulting in kmemleak showing
the following backtrace.
Fixes: 17c82e206d2a ("reset: Add APIs to manage array of resets") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Olof Johansson [Mon, 21 Oct 2019 19:07:35 +0000 (12:07 -0700)]
Merge tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci fixes for v5.4
======================
* fix GPIO backlight support on DA850 by enabling the needed config
in davinci_all_defconfig. This is a fix because the driver and board
support got converted to use BACKLIGHT_GPIO driver, but defconfig update
is still missing in v5.4.
* fix for McBSP DMA on DM365
* tag 'davinci-fixes-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
Olof Johansson [Mon, 21 Oct 2019 19:07:27 +0000 (12:07 -0700)]
Merge tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of fixes for individual boards like the rockpro64, and Hugsun X99
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
Olof Johansson [Mon, 21 Oct 2019 19:07:13 +0000 (12:07 -0700)]
Merge tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Olof Johansson [Mon, 21 Oct 2019 19:06:46 +0000 (12:06 -0700)]
Merge tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
More fixes for omap variants:
- Update more panel options in omap2plus_defconfig that got changed
as we moved to use generic LCD panels
- Remove unused twl_keypad for logicpd-torpedo-som to avoid boot
time warnings. This is only a cosmetic fix, but at least dmesg output
is now getting more readable after all the fixes to remove pointless
warnings
- Fix gpu_cm node name as we still have a non-standard node name
dependency for clocks. This should eventually get fixed by use
of domain specific compatible property
- Fix use of i2c-mux-idle-disconnect for m3874-iceboard
- Use level interrupt for omap4 & 5 wlcore to avoid lost edge
interrupts
* tag 'omap-for-v5.4/fixes-rc3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use level interrupt for omap4 & 5 wlcore
ARM: dts: am3874-iceboard: Fix 'i2c-mux-idle-disconnect' usage
ARM: dts: omap5: fix gpu_cm clock provider name
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
bcm2835-rpi.dtsi defines the behavior of the ACT LED, which is available
on all Raspberry Pi boards. But there is no driver for this particual
GPIO on CM3 in mainline yet, so this node was left incomplete without
the actual GPIO definition. Since commit 025bf37725f1 ("gpio: Fix return
value mismatch of function gpiod_get_from_of_node()") this causing probe
issues of the leds-gpio driver for users of the CM3 dtsi file.
leds-gpio: probe of leds failed with error -2
Until we have the necessary GPIO driver hide the ACT node for CM3
to avoid this.
Reported-by: Fredrik Yhlen <fredrik.yhlen@endian.se> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Fixes: a54fe8a6cf66 ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board") Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Suman Anna [Tue, 27 Aug 2019 00:14:52 +0000 (19:14 -0500)]
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
The OMAP3 ISP IOMMU does not have any reset lines, so it didn't
need any pdata previously. The OMAP IOMMU driver now requires the
platform data ops for device_enable/idle on all the IOMMU devices
after commit db8918f61d51 ("iommu/omap: streamline enable/disable
through runtime pm callbacks") to enable/disable the clocks properly
and maintain the reference count and the omap_hwmod state machine.
So, add these callbacks through iommu pdata quirks for the OMAP3
ISP IOMMU.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Tue, 27 Aug 2019 00:14:51 +0000 (19:14 -0500)]
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
The OMAP IOMMU driver requires the device_enable/idle platform
data ops on all the IOMMU devices to be able to enable and disable
the clocks after commit db8918f61d51 ("iommu/omap: streamline
enable/disable through runtime pm callbacks"). Plug in these
pdata ops for all the existing IOMMUs through pdata quirks to
maintain functionality.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
DA850 EVM has been converted to use GPIO backlight device
for display backlight GPIO control.
Enable the GPIO backlight module in davinci_all_defconfig
to keep backlight support working.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: edits to commit message for context] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Stefan Wahren [Mon, 23 Sep 2019 18:21:22 +0000 (20:21 +0200)]
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
The commit e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at
board level") accidently dropped the bus width for the sdhci on the
RPi Zero W, because the board file was relying on the defaults
from bcm2835-rpi.dtsi. So fix this performance regression by adding
the bus width to the board file.
Fixes: e7774049ff25 ("ARM: dts: bcm283x: Define MMC interfaces at board level") Reported-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Anson Huang [Mon, 7 Oct 2019 00:43:42 +0000 (08:43 +0800)]
ARM: dts: imx7s: Correct GPT's ipg clock source
i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.
Fixes: 3ef79ca6bd1d ("ARM: dts: imx7d: use imx7s.dtsi as base device tree") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify 'i2c-mux-idle-disconnect' for both I2C switches present on the
board, since both are connected to the same parent bus and all of
their children have the same I2C address.
Fixes: ca4b4d373fcc ("ARM: dts: vf610: Add ZII SCU4 AIB board") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Jeff White <jeff.white@zii.aero> Cc: Rick Ramstetter <rick@anteaterllc.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 2 Oct 2019 00:20:29 +0000 (19:20 -0500)]
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
A previous patch disabled the SNVS power key by default which
breaks the ability for the imx6q-logicpd board to wake from sleep.
This patch re-enables this feature for this board.
Fixes: 770856f0da5d ("ARM: dts: imx6qdl: Enable SNVS power key according to board design") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ran Wang [Tue, 17 Sep 2019 07:33:56 +0000 (15:33 +0800)]
arm64: dts: lx2160a: Correct CPU core idle state name
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Fixes: 00c5ce8ac023 ("arm64: dts: lx2160a: add cpu idle support") Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
When I re-posted Sean's original commit to add the override mode for
the kevin panel, for some reason I didn't notice that the pixel clock
wasn't quite right. Looking at /sys/kernel/debug/clk/clk_summary on
downstream kernels it can be seen that the VOP clock is supposed to be
266,666,667 Hz achieved by dividing the 800 MHz PLL by 3.
Looking at history, it seems that even Sean's first patch [1] had this
funny clock rate. I'm not sure where it came from since the commit
message specifically mentioned 26666 kHz and the Chrome OS tree [2]
can be seen to request 266667 kHz.
In any case, let's fix it up. This together with my patch [3] to do
the proper rounding when setting the clock rate makes the VOP clock
more proper as seen in /sys/kernel/debug/clk/clk_summary.
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is
connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed
property of the sdmmc controller, since no mmc card can be connected here.
Tony Lindgren [Wed, 9 Oct 2019 22:11:27 +0000 (15:11 -0700)]
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Commit 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.
However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().
And with commit e6818d29ea15 ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.
Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.
Fixes: 572cf7d7b07d ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29ea15 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup") Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Eyal Reizer <eyalr@ti.com> Cc: Guy Mishol <guym@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
According to
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt,
i2c-mux-idle-disconnect is a property of a parent node since it
pertains to the mux/switch as a whole, so move it there and drop all
of the concurrences in child nodes.
Fixes: d031773169df ("ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Benoît Cousson <bcousson@baylibre.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Graeme Smecher <gsmecher@threespeedlogic.com> Cc: linux-omap@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Tested-by: Graeme Smecher <gsmecher@threespeedlogic.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tero Kristo [Tue, 8 Oct 2019 07:56:42 +0000 (10:56 +0300)]
ARM: dts: omap5: fix gpu_cm clock provider name
The clkctrl code searches for the parent clockdomain based on the name
of the CM provider node. The introduction of SGX node for omap5 made
the node name for the gpu_cm to be clock-controller. There is no
clockdomain named like this, so the lookup fails. Fix by changing
the node name properly.
Fixes: 394534cb07d8 ("ARM: dts: Configure sgx for omap5") Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Maxime Ripard [Thu, 3 Oct 2019 15:48:42 +0000 (17:48 +0200)]
ARM: dts: sun7i: Drop the module clock from the device tree
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Maxime Ripard [Thu, 3 Oct 2019 15:48:41 +0000 (17:48 +0200)]
dt-bindings: media: sun4i-csi: Drop the module clock
It turns out that what was thought to be the module clock was actually the
clock meant to be used by the sensor, and isn't playing any role with the
CSI controller itself. Let's drop that clock from our binding.
Lucas Stach [Fri, 6 Sep 2019 17:06:01 +0000 (19:06 +0200)]
arm64: dts: zii-ultra: fix ARM regulator states
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
soc: imx: imx-scu: Getting UID from SCU should have response
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is
connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module.
So the data strobe cannot be used for its intended purpose on this board,
and so the HS400 eMMC mode is not functional. Limit the controller to HS200.
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a
max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an
additional note that the pwm parameter needs to be modified.
From the schematics a voltage range of 0.8V to 1.7V can be calculated.
Additional voltage measurements on the board show that this fix indeed
leads to the correct voltage, while without this fix the voltage was set
too high.
Adam Ford [Fri, 16 Aug 2019 22:58:12 +0000 (17:58 -0500)]
ARM: dts: logicpd-torpedo-som: Remove twl_keypad
The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed. This patch disables the twl_keypad driver
to remove some splat during boot:
twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps] Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming convention for the existing Theobroma boards is
soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel
devicetrees also follow that scheme.
For some reason in the binding a wrong or outdated naming slipped
in which does not match the used devicetrees and makes the dt-schema
complain now.
Fix this by using the names used in the wild by actual boards.
Fixes: a323a513c712 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema")
[although the issue was also present in the old txt file] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
arm64: dts: rockchip: fix Rockpro64 RK808 interrupt line
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the
Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt
line PMIC_INT_L from the RK808, and there's a note which translates as:
"PMU termination GPIO1_C5 changed to this".
Tested by setting an RTC wakealarm and checking /proc/interrupts counters.
Without this patch, neither the rockchip_gpio_irq counter for the RK808,
nor the RTC alarm counter increment when the alarm time is reached.
With this patch, both interrupt counters increment by 1 as expected.
Tony Lindgren [Thu, 3 Oct 2019 16:44:10 +0000 (09:44 -0700)]
ARM: omap2plus_defconfig: Fix selected panels after generic panel changes
The old omapdrm panels got removed for v5.4 in favor of generic panels,
and the Kconfig options changed. Let's update omap2plus_defconfig
accordingly so the same panels are still enabled.
Cc: Jyri Sarha <jsarha@ti.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Thu, 3 Oct 2019 16:15:17 +0000 (09:15 -0700)]
Merge tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Linus Walleij [Tue, 1 Oct 2019 07:46:28 +0000 (09:46 +0200)]
ARM: dts: ux500: Fix up the CPU thermal zone
This fixes up the default ux500 CPU thermal zone:
- Set polling delay to 0 and explain why
- Set passive polling delay to 250
- Remove restrictions from the CPU cooling device,
we should use all cpufreq steps to cool down if
needed.
Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org Fixes: b786a05f6ce4 ("ARM: dts: ux500: Update thermal zone") Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
It turns out that sopine-baseboard needs same fix as pine64-plus
for ethernet PHY. Here too Realtek ethernet PHY chip needs additional
power on delay to properly initialize. Datasheet mentions that chip
needs 30 ms to be properly powered on and that it needs some more time
to be initialized.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Note that issue was found out and fix tested on pine64-lts, but it's
basically the same as sopine-baseboard, only layout and connectors
differ.
Fixes: bdfe4cebea11 ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
Depending on kernel and bootloader configuration, it's possible that
Realtek ethernet PHY isn't powered on properly. According to the
datasheet, it needs 30ms to power up and then some more time before it
can be used.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Fixes: 94dcfdc77fc5 ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i") Suggested-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
Commit 6334150e9a36 ("remoteproc: don't allow modular build")
changes CONFIG_REMOTEPROC to a boolean from a tristate config
option which inhibits all defconfigs marking CONFIG_REMOTEPROC as
a module in compiling the remoteproc and dependent config options.
So fix the configs to have CONFIG_REMOTEPROC built in.
Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com Fixes: 6334150e9a36 ("remoteproc: don't allow modular build") Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Will Deacon <will@kernel.org>
[olof: Fixed up all 4 occurrances in this one commit] Signed-off-by: Olof Johansson <olof@lixom.net>
Merge tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A bunch of fixes that accumulated in recent weeks, mostly material for
stable.
Summary:
- fix for regression from 5.3 that prevents to use balance convert
with single profile
- qgroup fixes: rescan race, accounting leak with multiple writers,
potential leak after io failure recovery
- fix for use after free in relocation (reported by KASAN)
- other error handling fixups"
* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
btrfs: Fix a regression which we can't convert to SINGLE profile
btrfs: relocation: fix use-after-free on dead relocation roots
Btrfs: fix race setting up and completing qgroup rescan workers
Btrfs: fix missing error return if writeback for extent buffer never started
btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
Peter Ujfalusi [Mon, 30 Sep 2019 08:54:50 +0000 (11:54 +0300)]
ARM: dts: am4372: Set memory bandwidth limit for DISPC
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to
avoid underflow errors due to the bandwidth needs of higher resolutions.
am43xx can not provide enough bandwidth to DISPC to correctly handle
'high' resolutions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few more tracing fixes:
- Fix a buffer overflow by checking nr_args correctly in probes
- Fix a warning that is reported by clang
- Fix a possible memory leak in error path of filter processing
- Fix the selftest that checks for failures, but wasn't failing
- Minor clean up on call site output of a memory trace event"
* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Fix same probe error test
mm, tracing: Print symbol name for call_site in trace events
tracing: Have error path in predicate_parse() free its allocated memory
tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
tracing/probe: Fix to check the difference of nr_args before adding probe
Merge tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull more MMC updates from Ulf Hansson:
"A couple more updates/fixes for MMC:
- sdhci-pci: Add Genesys Logic GL975x support
- sdhci-tegra: Recover loss in throughput for DMA
- sdhci-of-esdhc: Fix DMA bug"
* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: host: sdhci-pci: Add Genesys Logic GL975x support
mmc: tegra: Implement ->set_dma_mask()
mmc: sdhci: Let drivers define their DMA mask
mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
mmc: sdhci: improve ADMA error reporting
csky: Move static keyword to the front of declaration
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com> Signed-off-by: Guo Ren <guoren@kernel.org>
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation/process update from Greg KH:
"Here are two small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Clarify disclosure rules
Documentation/process: Volunteer as the ambassador for Intel
Merge tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
"Fixes from the recent SMB3 Test events and Storage Developer
Conference (held the last two weeks).
Here are nine smb3 patches including an important patch for debugging
traces with wireshark, with three patches marked for stable.
Additional fixes from last week to better handle some newly discovered
reparse points, and a fix the create/mkdir path for setting the mode
more atomically (in SMB3 Create security descriptor context), and one
for path name processing are still being tested so are not included
here"
* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix oplock handling for SMB 2.1+ protocols
smb3: missing ACL related flags
smb3: pass mode bits into create calls
smb3: Add missing reparse tags
CIFS: fix max ea value size
fs/cifs/sess.c: Remove set but not used variable 'capabilities'
fs/cifs/smb2pdu.c: Make SMB2_notify_init static
smb3: fix leak in "open on server" perf counter
smb3: allow decryption keys to be dumped by admin for debugging
Mao Han [Wed, 25 Sep 2019 09:23:02 +0000 (17:23 +0800)]
csky: Fixup csky_pmu.max_period assignment
The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.
Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com> Signed-off-by: Guo Ren <ren_guo@c-sky.com>
This is admittedly partly "for discussion". We need to have a way
forward for the boot time deadlocks where user space ends up waiting for
more entropy, but no entropy is forthcoming because the system is
entirely idle just waiting for something to happen.
While this was triggered by what is arguably a user space bug with
GDM/gnome-session asking for secure randomness during early boot, when
they didn't even need any such truly secure thing, the issue ends up
being that our "getrandom()" interface is prone to that kind of
confusion, because people don't think very hard about whether they want
to block for sufficient amounts of entropy.
The approach here-in is to decide to not just passively wait for entropy
to happen, but to start actively collecting it if it is missing. This
is not necessarily always possible, but if the architecture has a CPU
cycle counter, there is a fair amount of noise in the exact timings of
reasonably complex loads.
We may end up tweaking the load and the entropy estimates, but this
should be at least a reasonable starting point.
As part of this, we also revert the revert of the ext4 IO pattern
improvement that ended up triggering the reported lack of external
entropy.
* getrandom() active entropy waiting:
Revert "Revert "ext4: make __ext4_get_inode_loc plug""
random: try to actively add entropy rather than passively wait for it
Instead of waiting forever for entropy that may just not happen, we now
try to actively generate entropy when required, and are thus hopefully
avoiding the problem that caused the nice ext4 IO pattern fix to be
reverted.
So revert the revert.
Cc: Ahmed S. Darwish <darwish.07@gmail.com> Cc: Ted Ts'o <tytso@mit.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Alexander E. Patrakov <patrakov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
random: try to actively add entropy rather than passively wait for it
For 5.3 we had to revert a nice ext4 IO pattern improvement, because it
caused a bootup regression due to lack of entropy at bootup together
with arguably broken user space that was asking for secure random
numbers when it really didn't need to.
See commit 72dbcf721566 (Revert "ext4: make __ext4_get_inode_loc plug").
This aims to solve the issue by actively generating entropy noise using
the CPU cycle counter when waiting for the random number generator to
initialize. This only works when you have a high-frequency time stamp
counter available, but that's the case on all modern x86 CPU's, and on
most other modern CPU's too.
What we do is to generate jitter entropy from the CPU cycle counter
under a somewhat complex load: calling the scheduler while also
guaranteeing a certain amount of timing noise by also triggering a
timer.
I'm sure we can tweak this, and that people will want to look at other
alternatives, but there's been a number of papers written on jitter
entropy, and this should really be fairly conservative by crediting one
bit of entropy for every timer-induced jump in the cycle counter. Not
because the timer itself would be all that unpredictable, but because
the interaction between the timer and the loop is going to be.
Even if (and perhaps particularly if) the timer actually happens on
another CPU, the cacheline interaction between the loop that reads the
cycle counter and the timer itself firing is going to add perturbations
to the cycle counter values that get mixed into the entropy pool.
As Thomas pointed out, with a modern out-of-order CPU, even quite simple
loops show a fair amount of hard-to-predict timing variability even in
the absense of external interrupts. But this tries to take that further
by actually having a fairly complex interaction.
This is not going to solve the entropy issue for architectures that have
no CPU cycle counter, but it's not clear how (and if) that is solvable,
and the hardware in question is largely starting to be irrelevant. And
by doing this we can at least avoid some of the even more contentious
approaches (like making the entropy waiting time out in order to avoid
the possibly unbounded waiting).
Cc: Ahmed Darwish <darwish.07@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Nicholas Mc Guire <hofrat@opentech.at> Cc: Andy Lutomirski <luto@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Willy Tarreau <w@1wt.eu> Cc: Alexander E. Patrakov <patrakov@gmail.com> Cc: Lennart Poettering <mzxreary@0pointer.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sun, 29 Sep 2019 18:19:25 +0000 (11:19 -0700)]
Merge tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Olof Johansson [Sun, 29 Sep 2019 18:19:18 +0000 (11:19 -0700)]
Merge tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARM SCMI fixes for v5.4
Couple of fixes: one in scmi reset driver initialising missed scmi handle
and an other in scmi reset API implementation fixing the assignment of
reset state
* tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
Merge tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
More libnvdimm updates from Dan Williams:
- Complete the reworks to interoperate with powerpc dynamic huge page
sizes
- Fix a crash due to missed accounting for the powerpc 'struct
page'-memmap mapping granularity
- Fix badblock initialization for volatile (DRAM emulated) pmem ranges
- Stop triggering request_key() notifications to userspace when
NVDIMM-security is disabled / not present
- Miscellaneous small fixups
* tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/region: Enable MAP_SYNC for volatile regions
libnvdimm: prevent nvdimm from requesting key when security is disabled
libnvdimm/region: Initialize bad block for volatile namespaces
libnvdimm/nfit_test: Fix acpi_handle redefinition
libnvdimm/altmap: Track namespace boundaries in altmap
libnvdimm: Fix endian conversion issues
libnvdimm/dax: Pick the right alignment default when creating dax devices
powerpc/book3s64: Export has_transparent_hugepage() related functions.
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code