Olof Johansson [Sat, 7 Dec 2019 22:49:53 +0000 (14:49 -0800)]
ALSA: echoaudio: simplify get_audio_levels
The loop optimizer seems to go astray here, and produces some warnings
that don't seem valid.
Still, the code can be simplified -- just clear the whole array at the
beginning, and fill in whatever values are valid on the platform.
Warnings before this change (GCC 8.2.0 ARM allmodconfig):
In file included from ../sound/pci/echoaudio/gina24.c:115:
../sound/pci/echoaudio/echoaudio.c: In function 'snd_echo_vumeters_get':
../sound/pci/echoaudio/echoaudio_dsp.c:647:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
In file included from ../sound/pci/echoaudio/layla24.c:112:
../sound/pci/echoaudio/echoaudio.c: In function 'snd_echo_vumeters_get':
../sound/pci/echoaudio/echoaudio_dsp.c:658:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
../sound/pci/echoaudio/echoaudio_dsp.c:647:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
Takashi Iwai [Wed, 4 Dec 2019 14:48:24 +0000 (15:48 +0100)]
ALSA: pcm: oss: Avoid potential buffer overflows
syzkaller reported an invalid access in PCM OSS read, and this seems
to be an overflow of the internal buffer allocated for a plugin.
Since the rate plugin adjusts its transfer size dynamically, the
calculation for the chained plugin might be bigger than the given
buffer size in some extreme cases, which lead to such an buffer
overflow as caught by KASAN.
Fix it by limiting the max transfer size properly by checking against
the destination size in each plugin transfer callback.
Takashi Iwai [Tue, 3 Dec 2019 15:41:05 +0000 (16:41 +0100)]
ALSA: hda: hdmi - Keep old slot assignment behavior for Intel platforms
The commit 609f5485344b ("ALSA: hda: hdmi - preserve non-MST PCM
routing for Intel platforms") tried to restore the old behavior wrt
assignment of the PCM slot for Intel platforms, but this didn't do it
right. As found in the later discussion, a positive pipe id on Intel
platforms can be passed for single monitor attachment case.
This patch reverts the previous attempt and applies a simpler
workaround instead. Actually, for Intel platforms, we can handle as
if per_pin->dev_id=0, assign the primary slot at the first try. This
assures the compatible behavior with the previous versions regarding
the slot assignment.
Takashi Iwai [Mon, 2 Dec 2019 07:49:47 +0000 (08:49 +0100)]
ALSA: hda: Modify stream stripe mask only when needed
The recent commit in HD-audio stream management for changing the
stripe control seems causing a regression on some platforms. The
stripe control is currently used only by HDMI codec, and applying the
stripe mask unconditionally may lead to scratchy and static noises as
seen on some MacBooks.
For addressing the regression, this patch changes the stream
management code to apply the stripe mask conditionally only when the
codec driver requested.
Jaroslav Kysela [Fri, 29 Nov 2019 14:40:27 +0000 (15:40 +0100)]
ALSA: hda - fixup for the bass speaker on Lenovo Carbon X1 7th gen
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
Commit 5398e94fb753 ("ALSA: hda - Add DP-MST support for NVIDIA codecs")
introduced a slight change of behaviour how non-MST monitors are
assigned to PCMs on Intel platforms.
In the drm_audio_component.h interface, the third parameter
to pin_eld_notify() is pipe number. On Intel platforms, this value
is -1 for MST. On other platforms, a non-zero pipe id is used to
signal MST use.
This difference leads to some subtle differences in hdmi_find_pcm_slot()
with regards to how non-MST monitors are assigned to PCMs.
This patch restores the original behaviour on Intel platforms while
keeping the new allocation policy on other platforms.
Add additional check in hdmi_find_pcm_slot() to not return
a pcm index that points to unallocated pcm. This could happen
if codec driver is set up in codec->mst_no_extra_pcms mode.
On some platforms, this leads to a kernel oops in snd_ctl_notify(),
called via update_eld().
We've added the bass speaker support on Acer 8951G by the commit 00066e9733f6 ("Add Acer Aspire Ethos 8951G model quirk"), but it seems
that the GPIO pin was wrongly set: while the commit turns off the bit
to power up the amp, the actual hardware reacts other way round,
i.e. GPIO bit on = amp on.
So this patch fixes the bug, turning on the GPIO bit 0x02 as default.
Since turning on the GPIO bit can be more easily managed with
alc_setup_gpio() call, we simplify the quirk code by integrating the
GPIO setup into the existing alc662_fixup_aspire_ethos_hp() and
dropping the whole ALC669_FIXUP_ACER_ASPIRE_ETHOS_SUBWOOFER quirk.
Kai Vehmanen [Wed, 27 Nov 2019 16:12:40 +0000 (18:12 +0200)]
ALSA: hda: hdmi - fix regression in connect list handling
Fix regression in how intel_haswell_fixup_connect_list()
results are used in hda_read_pin_conn(). Use of
snd_hda_get_raw_connections() in hda_read_pin_conn() bypasses
the cache and thus also bypasses the overridden pin connection
list. On platforms that require the connection list fixup,
mux list will be empty and HDMI playback will fail to -EBUSY
at open.
Fix the regression in hda_read_pinn_conn(). Simplify code
as suggested by Takashi Iwai to remove old
intel_haswell_fixup_connect_list() and copy the cvt_nid list
directly and not use snd_hda_override_conn_list() at all.
Andrew Gabbasov [Wed, 27 Nov 2019 11:06:22 +0000 (05:06 -0600)]
ALSA: aloop: Avoid pointer dereference before null-check
Static analysis tools (cppcheck and PVS Studio) report an error
in loopback_snd_timer_period_elapsed() regarding dpcm_play pointer
dereference earlier than its null-check. And although this is a result
of a formal check, and the pointer correctness is also protected
by having a corresponding bit set in the "running" mask, re-ordering
of the lines can imake the code even formally correct and eliminate
those static analysis error reports.
Fixes: 26c53379f98d ("ALSA: aloop: Support selection of snd_timer instead of jiffies") Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Link: https://lore.kernel.org/r/20191127110622.26105-1-andrew_gabbasov@mentor.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alex Deucher [Fri, 22 Nov 2019 21:43:50 +0000 (16:43 -0500)]
ALSA: hda/hdmi - fix vgaswitcheroo detection for AMD
Only enable the vga_switcheroo logic on systems with the
ATPX ACPI method. This logic is not needed for asics
that are not part of a PX (PowerXpress)/HG (Hybrid Graphics)
platform.
The Scarlett 6i6 has no padding on rear inputs 3/4 but a gainstage.
This patch introduces this functionality as to be seen in the mac
or windows scarlett control.
The correct address could already be found in the dump info, but was
never used. Without this patch inputs 3/4 are quite unusable else.
Jian-Hong Pan [Mon, 25 Nov 2019 09:34:06 +0000 (17:34 +0800)]
ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC
Laptops like ASUS UX431FLC and UX431FL can share the same audio quirks.
But UX431FLC needs one more step to enable the internal speaker: Pull
the GPIO from CODEC to initialize the AMP.
Fixes: 60083f9e94b2 ("ALSA: hda/realtek - Enable internal speaker & headset mic of ASUS UX431FL") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191125093405.5702-1-jian-hong@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nilkanth Ahirrao [Thu, 21 Nov 2019 11:10:23 +0000 (12:10 +0100)]
ASoC: rsnd: fix DALIGN register for SSIU
The current driver only sets 0x76543210 and 0x67452301 for DALIGN.
This doesn’t work well for TDM split and ex-split mode for all SSIU.
This patch programs the DALIGN registers based on the SSIU number.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Fixes: a914e44693d41b ("ASoC: rsnd: more clear rsnd_get_dalign() for DALIGN") Signed-off-by: Nilkanth Ahirrao <anilkanth@jp.adit-jv.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20191121111023.10976-1-erosca@de.adit-jv.com Signed-off-by: Mark Brown <broonie@kernel.org>
loopback_snd_timer_close_cable() function waits until all
scheduled tasklets are completed, but the timer is closed after that
and can generate more event callbacks, scheduling new tasklets,
that will not be synchronized with cable closing.
Move tasklet_kill() call to be executed after snd_timer_close()
call to avoid such case.
Andrew Gabbasov [Fri, 22 Nov 2019 17:52:17 +0000 (11:52 -0600)]
ALSA: aloop: Remove redundant locking in timer open function
loopback_parse_timer_id() uses snd_card_ref(), that can lock on mutex,
also snd_timer_instance_new() uses non-atomic allocation, that can sleep.
So, both functions can not be called from loopback_snd_timer_open()
with cable->lock spinlock locked.
Moreover, most part of loopback_snd_timer_open() function body works
when the opposite stream of the same cable does not yet exist, and
the current stream is not yet completely open and can't be running,
so existing locking of loopback->cable_lock mutex is enough to protect
from conflicts with simultaneous opening or closing.
Locking of cable->lock spinlock is not needed in this case.
Takashi Iwai [Thu, 21 Nov 2019 19:07:08 +0000 (20:07 +0100)]
ASoC: pcm: Make ioctl ops optional
Now PCM core accepts the NULL ioctl ops as default, and passing a proper
ioctl ops is no longer mandatory. Adjust soc_new_pcm() to allow also
the NULL for component ioctl ops, too.
The old Nvidia chips have multiple HD-audio codecs on the same
HD-audio controller, and this doesn't work as expected with the current
audio component binding that is implemented under the one-codec-per-
controller assumption; at the probe time, the driver leads to several
kernel WARNING messages.
For the proper support, we may change the pin2port and port2pin to
traverse the codec list per the given pin number, but this needs more
development and testing.
As a quick workaround, instead, this patch drops the binding in the
audio side for these legacy chips since the audio component support in
nouveau graphics driver is still not merged (hence it's basically
unused).
Colin Ian King [Fri, 22 Nov 2019 13:13:54 +0000 (13:13 +0000)]
ALSA: cs4236: fix error return comparison of an unsigned integer
The return from pnp_irq is an unsigned integer type resource_size_t
and hence the error check for a positive non-error code is always
going to be true. A check for a non-failure return from pnp_irq
should in fact be for (resource_size_t)-1 rather than >= 0.
Takashi Iwai [Fri, 22 Nov 2019 11:28:40 +0000 (12:28 +0100)]
ALSA: usb-audio: Fix NULL dereference at parsing BADD
snd_usb_mixer_controls_badd() that parses UAC3 BADD profiles misses a
NULL check for the given interfaces. When a malformed USB descriptor
is passed, this may lead to an Oops, as spotted by syzkaller.
Skip the iteration if the interface doesn't exist for avoiding the
crash.
The s6i6_gen2_info.ports[] array had the Mixer and PCM port type
entries in the wrong place. Use designators to explicitly specify the
array elements being set.
Fixes: 9e4d5c1be21f ("ALSA: usb-audio: Scarlett Gen 2 mixer interface") Signed-off-by: Geoffrey D. Bennett <g@b4.vu> Tested-by: Alex Fellows <alex.fellows@gmail.com> Tested-by: Markus Schroetter <project.m.schroetter@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191110134356.GA31589@b4.vu Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hui Wang [Thu, 21 Nov 2019 02:26:44 +0000 (10:26 +0800)]
ALSA: hda/realtek - Move some alc236 pintbls to fallback table
We have a new Dell machine which needs to apply the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, try to use the fallback table
to fix it this time. And we could remove all pintbls of alc236
for applying DELL1_MIC_NO_PRESENCE on Dell machines.
Hui Wang [Thu, 21 Nov 2019 02:26:43 +0000 (10:26 +0800)]
ALSA: hda/realtek - Move some alc256 pintbls to fallback table
We have a new Dell machine which needs to apply the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, try to use the fallback table
to fix it this time. And we could remove all pintbls of alc256
for applying DELL1_MIC_NO_PRESENCE on Dell machines.
Takashi Iwai [Sun, 17 Nov 2019 08:53:07 +0000 (09:53 +0100)]
ALSA: pcm: Add card sync_irq field
Many PCI and other drivers performs snd_pcm_period_elapsed() simply in
its interrupt handler, so the sync_stop operation is just to call
synchronize_irq(). Instead of putting this call multiple times,
introduce the common card->sync_irq field. When this field is set,
PCM core performs synchronize_irq() for sync-stop operation. Each
driver just needs to copy its local IRQ number to card->sync_irq, and
that's all we need.
Takashi Iwai [Sun, 17 Nov 2019 08:53:06 +0000 (09:53 +0100)]
ALSA: pcm: Add the support for sync-stop operation
The standard programming model of a PCM sound driver is to process
snd_pcm_period_elapsed() from an interrupt handler. When a running
stream is stopped, PCM core calls the trigger-STOP PCM ops, sets the
stream state to SETUP, and moves on to the next step. This is
performed in an atomic manner -- this could be called from the interrupt
context, after all.
The problem is that, if the stream goes further and reaches to the
CLOSE state immediately, the stream might be still being processed in
snd_pcm_period_elapsed() in the interrupt context, and hits a NULL
dereference. Such a crash happens because of the atomic operation,
and we can't wait until the stream-stop finishes.
For addressing such a problem, this commit adds a new PCM ops,
sync_stop. This gets called at the appropriate places that need a
sync with the stream-stop, i.e. at hw_params, prepare and hw_free.
Some drivers already have a similar mechanism implemented locally, and
we'll refactor the code later.
Takashi Iwai [Sun, 17 Nov 2019 08:53:03 +0000 (09:53 +0100)]
ALSA: pcm: Allow NULL ioctl ops
Currently PCM ioctl ops is a mandatory field but almost all drivers
simply pass snd_pcm_lib_ioctl. For simplicity, allow to set NULL in
the field and call snd_pcm_lib_ioctl() as default.
This patch adds the support for the feature to automatically allocate
and free PCM buffers, so called "managed buffer allocation" mode.
It's set up via new PCM helpers, snd_pcm_set_managed_buffer() and
snd_pcm_set_managed_buffer_all(), both of which correspond to the
existing preallocator helpers, snd_pcm_lib_preallocate_pages() and
snd_pcm_lib_preallocate_pages_for_all(). When the new helper is used,
it not only performs the pre-allocation of buffers, but also it
manages to call snd_pcm_lib_malloc_pages() before the PCM hw_params
ops and snd_lib_pcm_free() after the PCM hw_free ops inside PCM core,
respectively. This allows drivers to drop the explicit calls of the
memory allocation / release functions, and it will be a good amount of
code reduction in the end of this patch series.
When the PCM substream is set to the managed buffer allocation mode,
the managed_buffer_alloc flag is set in the substream object. Since
some drivers want to know when a buffer is newly allocated or
re-allocated at hw_params callback (e.g. want to set up the additional
stuff for the given buffer only at allocation time), now PCM core
turns on buffer_changed flag when the buffer has changed.
The standard conversions to use the new API will be straightforward:
- Replace snd_pcm_lib_preallocate*() calls with the corresponding
snd_pcm_set_managed_buffer*(); the arguments should be unchanged
- Drop superfluous snd_pcm_lib_malloc() and snd_pcm_lib_free() calls;
the check of snd_pcm_lib_malloc() returns should be replaced with
the check of runtime->buffer_changed flag.
- If hw_params or hw_free becomes empty, drop them from PCM ops
Andrew Gabbasov [Wed, 20 Nov 2019 17:49:55 +0000 (11:49 -0600)]
ALSA: aloop: Support runtime change of snd_timer via info interface
Show and change sound card timer source with read-write info
file in proc filesystem. Initial string can still be set as
module parameter.
The timer source string value can be changed at any time,
but it is latched by PCM substream open callback (the first one
for a particular cable). At this point it is actually used, that
is the string is parsed, and the timer is looked up and opened.
The timer source is set for a loopback card (the same as initial
setting by module parameter), but every cable uses the value,
current at the moment of open.
Setting the value to empty string switches the timer to jiffies.
Timo Wischer [Wed, 20 Nov 2019 17:49:54 +0000 (11:49 -0600)]
ALSA: aloop: Support selection of snd_timer instead of jiffies
to do synchronous audio forwarding between hardware sound card and aloop
devices. Such an audio route could look like the following:
Sound card -> Loopback application -> ALSA loop device -> arecord
In this case the loopback device should use the sound timer of the sound
card. Without this patch the loopback application has to implement an
adaptive sample rate converter to align the different clocks of the
different ALSA devices.
The used timer can be selected by referring to a sound card, its device
and subdevice, when loading the module:
$ modprobe snd_aloop enable=1 timer_source=[<card>[.<dev>[.<subdev>]]]
<card> is the name (id) of the sound card or a card number.
<dev> and <subdev> are device and subdevice numbers (defaults are 0).
Empty string as a value of timer_source= parameter enables previous
functionality (using jiffies timer).
Shengjiu Wang [Tue, 12 Nov 2019 10:46:42 +0000 (18:46 +0800)]
ASoC: soc-pcm: check symmetry before hw_params
This reverts commit 957ce0c6b8a1f (ASoC: soc-pcm: check symmetry after
hw_params).
That commit cause soc_pcm_params_symmetry can't take effect.
cpu_dai->rate, cpu_dai->channels and cpu_dai->sample_bits
are updated in the middle of soc_pcm_hw_params, so move
soc_pcm_params_symmetry to the end of soc_pcm_hw_params is
not a good solution, for judgement of symmetry in the function
is always true.
FIXME:
According to the comments of that commit, I think the case
described in the commit should disable symmetric_rates
in Back-End, rather than changing the position of
soc_pcm_params_symmetry.
Jaroslav Kysela [Tue, 19 Nov 2019 17:49:32 +0000 (18:49 +0100)]
ASoC: add control components management
This ASCII string can carry additional information about
soundcard components or configuration. Add the possibility
to set this string via the ASoC card.
soc-topology adds extra dai_link by using snd_soc_add_dai_link(),
and removes it by snd_soc_romove_dai_link().
This snd_soc_add/remove_dai_link() and/or its related
functions are unbalanced before, and now, these are balance-uped.
But, it finds the random operation issue, and it is reported by
Pierre-Louis.
When card was released, topology will call snd_soc_remove_dai_link()
via (A).
/* This should be called before snd_card_free() */
(A) soc_remove_link_components(card);
/* free the ALSA card at first; this syncs with pending operations */
if (card->snd_card) {
(B) snd_card_free(card->snd_card);
card->snd_card = NULL;
}
/* remove and free each DAI */
(X) soc_remove_link_dais(card);
/* need to sync the delayed work before releasing resources */
flush_delayed_work(&rtd->delayed_work);
snd_soc_pcm_component_free(rtd);
}
Here, it gets rtd via pcm->private_data.
But, topology related rtd are already freed at (A).
Normal sound card has no damage, becase it frees rtd at (C).
These are finalizing rtd related data.
Thus, these should be called when rtd was freed, not sound card
was freed. It is very natural and understandable.
In other words, pcm->private_free = soc_pcm_private_free()
is no longer needed.
Extra issue is that there is zero chance to call
soc_remove_dai() for topology related dai at (X).
Because (A) removes rtd connection from card too, and,
(X) is based on card connected rtd.
This means, (X) need to be called before (C) (= for normal sound)
and (A) (= for topology).
Now, I want to focus this patch which is the reason why
snd_card_free() = (B) is located there.
Original snd_card_free() was called last of this function.
But moved to top to avoid use-after-free issue.
The issue was happen at soc_pcm_free() which was pcm->private_free,
today it is updated/renamed to soc_pcm_private_free().
In other words, (B) need to be called before (C) (= for normal sound)
and (A) (= for topology), because it needs (not yet freed) rtd.
But, (A) need to be called before (B),
because it needs card->snd_card pointer.
If we call flush_delayed_work() and snd_soc_pcm_component_free()
(= same as soc_pcm_private_free()) when rtd was freed (= (C), (A)),
there is no reason to call snd_card_free() at top of this function.
It can be called end of this function, again.
But, in such case, it will likely break unbind again, as Takashi-san
reported. When unbind is performed in a busy state, the code may
release still-in-use resources.
At least we need to call snd_card_disconnect_sync() at the first place.
When the Acer Switch 10 SW5-012 quirk was added we did not have
jack-detection support yet; and the builtin microphone selection of
the original quirk is wrong too.
Fix the microphone-input quirk and add jack-detection info so that the
internal-microphone and headphone/set jack on the Switch 10 work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191119145138.59162-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org>
Nikhil Mahale [Tue, 19 Nov 2019 08:47:10 +0000 (14:17 +0530)]
ALSA: hda - Add DP-MST support for NVIDIA codecs
This patch adds DP-MST support for GK104+ NVIDIA codecs.
GK104+ NVIDIA codecs support DP-MST audio. These codecs have 4
output converters and 4 pin widgets, with 4 device entries per pin
widget for a total of 16 device entries.
This patch moves the existing patch_nvhdmi() definition to
patch_nvhdmi_legacy(), used by pre-GK104 NVIDIA codecs. Redefine
patch_nvhdmi() to enable DP-MST support by setting codec->dp_mst and
spec->dyn_pcm_assign.
Introduce fresh logic for dynamic pcm assignment, making
sure that new pcm assignments are compatible with the legacy static
per_pin-pmc assignment that existed in the days before DP-MST.
Nikhil Mahale [Tue, 19 Nov 2019 08:47:09 +0000 (14:17 +0530)]
ALSA: hda - Add DP-MST support for non-acomp codecs
This patch make it possible for non-acomp codecs to set
dyn_pcm_assign/dp_mst and get DP-MST audio support.
Document change notification HDA040-A for the Intel High Definition
Audio 1.0a specification introduces a Device Select verb for Digital
Display Pin Widgets that are multi-stream capable. This verb selects
a Device Entry that is used by subsequent Pin Widget verbs.
Once the Device Entry is selected, all subsequent Pin Widget verbs
controlling the sink device will be directed to the selected Device
Entry until the Device Select verb is updated with a new value.
These Pin Widget verbs include:
* Connection Select
* Get Connection List Entry
* Amplifier Gain/Mute
* Power State
* Pin Widget Control
* ELD Data
* DIP-Size
* DIP-Index
* DIP-Data
* DIP-XmitCtrl
* Content Protection Control
* ASP Channel Mapping
This patch adds calls to snd_hda_set_dev_select() to direct each of
these Pin Widget control verbs to the correct Device Entry.
snd_hda_get_connections() does not return per-device connection
list, therefore make use snd_hda_get_raw_connections() instead of
snd_hda_get_connections().
Nikhil Mahale [Tue, 19 Nov 2019 08:47:08 +0000 (14:17 +0530)]
ALSA: hda - Add DP-MST jack support
This patch adds DP-MST jack support which will be used on NVIDIA
platforms. Today, DP-MST audio is supported only if the codec has
acomp support. This patch makes it possible to add DP-MST support
for non-acomp codecs.
For the codecs supporting DP-MST audio, each pin can contain several
device entries. Each device entry is a virtual pin, described by
pin_nid and dev_id in struct hdmi_spec_per_pin. For monitor hotplug
event handling, non-acomp codecs enable and register jack-detection
for every hdmi_spec_per_pin.
This patch updates every relevant function in hda_jack.h and its
implementation in hda_jack.c, to consider dev_id along with pin_nid.
Changes to the HD Audio specification to support DP-MST audio are
described in the Intel Document Change Notification (DCN) number
HDA040-A.
From HDA040-A, "For the case of multi stream capable Digital Display
Pin Widget, [the Get Pin Sense verb] can be used to read a specific
Device Entry state as reported in Get Device List Entry verb." This
patch updates the read_pin_sense() function to take the dev_id as an
argument and pass it as a parameter to the Get Pin Sense verb.
Bits 15 through 20 from the Unsolicited Response for intrinsic
events contain the index of the Device Entry that generated the
event. This patch updates the Unsolicited Response event handlers to
extract the device entry index from the response and pass it to
snd_hda_jack_tbl_get_from_tag().
This patch updates snd_hda_jack_tbl_new() to take a dev_id argument
and store it in the jack structure, and to make sure not to generate
a different tag when called more than once for the same nid.
Li Xu [Fri, 15 Nov 2019 19:54:13 +0000 (13:54 -0600)]
ASoC: wm_adsp: Expose mixer control API
Expose mixer control API for reading and writing controls from the kernel.
This API can be used by ALSA kernel drivers with ADSP support to
read and write firmware-defined memory regions.
Lucas Stach [Mon, 18 Nov 2019 15:12:06 +0000 (16:12 +0100)]
ASoC: tlv320aic31xx: configure output common-mode voltage
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Mark Brown [Mon, 18 Nov 2019 15:52:47 +0000 (15:52 +0000)]
ASoC: SOF: Intel: Fix build break
Commit 130d3e9077 (Fix CFL and CML FW nocodec binary names.) broke the
build in some configurations as it depends on changes in the development
branch, revert it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 15 Nov 2019 10:27:03 +0000 (15:57 +0530)]
ALSA: compress: add flac decoder params
The current design of sending codec parameters assumes that decoders
will have parsers so they can parse the encoded stream for parameters
and configure the decoder.
But this assumption may not be universally true and we know some DSPs
which do not contain the parsers so additional parameters are required
to be passed.
So add these parameters starting with FLAC decoder. The size of
snd_codec_options is still 120 bytes after this change (due to this
being a union)
Shuming Fan [Mon, 18 Nov 2019 09:16:24 +0000 (17:16 +0800)]
ASoC: rt5682: fix the charge pump capacitor discharges
Due to switching the HV to LV mode while stopping playback,
the charge pump capacitor will be discharged to the source of the pump circuit.
Therefore, this patch removed the event control.
Linus Torvalds [Sun, 17 Nov 2019 19:27:44 +0000 (11:27 -0800)]
Merge tag 'iommu-fixes-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix for Intel IOMMU to correct invalidation commands when in SVA
mode.
- Update MAINTAINERS entry for Intel IOMMU
* tag 'iommu-fixes-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix QI_DEV_IOTLB_PFSID and QI_DEV_EIOTLB_PFSID macros
MAINTAINERS: Update for INTEL IOMMU (VT-d) entry
Linus Torvalds [Sun, 17 Nov 2019 16:15:41 +0000 (08:15 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"An I2C core fix to prevent a use-after-free in a rare error path,
and an I2C ACPI addition to work around broken HW/firmware related
to touchscreens"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: fix use after free in of_i2c_notify
i2c: acpi: Force bus speed to 400KHz if a Silead touchscreen is present
Linus Torvalds [Sun, 17 Nov 2019 02:14:32 +0000 (18:14 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This reverts a number of changes to the khwrng thread which feeds the
kernel random number pool from hwrng drivers. They were trying to fix
issues with suspend-and-resume but ended up causing regressions"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "hwrng: core - Freeze khwrng thread during suspend"
Herbert Xu [Sun, 17 Nov 2019 00:48:17 +0000 (08:48 +0800)]
Revert "hwrng: core - Freeze khwrng thread during suspend"
This reverts commit 03a3bb7ae631 ("hwrng: core - Freeze khwrng
thread during suspend"), ff296293b353 ("random: Support freezable
kthreads in add_hwgenerator_randomness()") and 59b569480dc8 ("random:
Use wait_event_freezable() in add_hwgenerator_randomness()").
These patches introduced regressions and we need more time to
get them ready for mainline.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1) Fix memory leak in xfrm_state code, from Steffen Klassert.
2) Fix races between devlink reload operations and device
setup/cleanup, from Jiri Pirko.
3) Null deref in NFC code, from Stephan Gerhold.
4) Refcount fixes in SMC, from Ursula Braun.
5) Memory leak in slcan open error paths, from Jouni Hogander.
6) Fix ETS bandwidth validation in hns3, from Yonglong Liu.
7) Info leak on short USB request answers in ax88172a driver, from
Oliver Neukum.
8) Release mem region properly in ep93xx_eth, from Chuhong Yuan.
9) PTP config timestamp flags validation, from Richard Cochran.
10) Dangling pointers after SKB data realloc in seg6, from Andrea Mayer.
11) Missing free_netdev() in gemini driver, from Chuhong Yuan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (56 commits)
ipmr: Fix skb headroom in ipmr_get_route().
net: hns3: cleanup of stray struct hns3_link_mode_mapping
net/smc: fix fastopen for non-blocking connect()
rds: ib: update WR sizes when bringing up connection
net: gemini: add missed free_netdev
net: dsa: tag_8021q: Fix dsa_8021q_restore_pvid for an absent pvid
seg6: fix skb transport_header after decap_and_validate()
seg6: fix srh pointer in get_srh()
net: stmmac: Use the correct style for SPDX License Identifier
octeontx2-af: Use the correct style for SPDX License Identifier
ptp: Extend the test program to check the external time stamp flags.
mlx5: Reject requests to enable time stamping on both edges.
igb: Reject requests that fail to enable time stamping on both edges.
dp83640: Reject requests to enable time stamping on both edges.
mv88e6xxx: Reject requests to enable time stamping on both edges.
ptp: Introduce strict checking of external time stamp options.
renesas: reject unsupported external timestamp flags
mlx5: reject unsupported external timestamp flags
igb: reject unsupported external timestamp flags
dp83640: reject unsupported external timestamp flags
...
Guillaume Nault [Fri, 15 Nov 2019 17:29:52 +0000 (18:29 +0100)]
ipmr: Fix skb headroom in ipmr_get_route().
In route.c, inet_rtm_getroute_build_skb() creates an skb with no
headroom. This skb is then used by inet_rtm_getroute() which may pass
it to rt_fill_info() and, from there, to ipmr_get_route(). The later
might try to reuse this skb by cloning it and prepending an IPv4
header. But since the original skb has no headroom, skb_push() triggers
skb_under_panic():
Actually the original skb used to have enough headroom, but the
reserve_skb() call was lost with the introduction of
inet_rtm_getroute_build_skb() by commit 404eb77ea766 ("ipv4: support
sport, dport and ip_proto in RTM_GETROUTE").
We could reserve some headroom again in inet_rtm_getroute_build_skb(),
but this function shouldn't be responsible for handling the special
case of ipmr_get_route(). Let's handle that directly in
ipmr_get_route() by calling skb_realloc_headroom() instead of
skb_clone().
Fixes: 404eb77ea766 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 15 Nov 2019 11:39:30 +0000 (12:39 +0100)]
net/smc: fix fastopen for non-blocking connect()
FASTOPEN does not work with SMC-sockets. Since SMC allows fallback to
TCP native during connection start, the FASTOPEN setsockopts trigger
this fallback, if the SMC-socket is still in state SMC_INIT.
But if a FASTOPEN setsockopt is called after a non-blocking connect(),
this is broken, and fallback does not make sense.
This change complements
commit cd2063604ea6 ("net/smc: avoid fallback in case of non-blocking connect")
and fixes the syzbot reported problem "WARNING in smc_unhash_sk".
Reported-by: syzbot+8488cc4cf1c9e09b8b86@syzkaller.appspotmail.com Fixes: e1bbdd570474 ("net/smc: reduce sock_put() for fallback sockets") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dag Moxnes [Fri, 15 Nov 2019 08:56:01 +0000 (09:56 +0100)]
rds: ib: update WR sizes when bringing up connection
Currently WR sizes are updated from rds_ib_sysctl_max_send_wr and
rds_ib_sysctl_max_recv_wr when a connection is shut down. As a result,
a connection being down while rds_ib_sysctl_max_send_wr or
rds_ib_sysctl_max_recv_wr are updated, will not update the sizes when
it comes back up.
Move resizing of WRs to rds_ib_setup_qp so that connections will be setup
with the most current WR sizes.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chuhong Yuan [Fri, 15 Nov 2019 06:24:54 +0000 (14:24 +0800)]
net: gemini: add missed free_netdev
This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 16 Nov 2019 16:08:25 +0000 (18:08 +0200)]
net: dsa: tag_8021q: Fix dsa_8021q_restore_pvid for an absent pvid
This sequence of operations:
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan del dev swp2 vid 1
ip link set dev br0 type bridge vlan_filtering 1
ip link set dev br0 type bridge vlan_filtering 0
apparently fails with the message:
[ 31.305716] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering
[ 31.322161] sja1105 spi0.1: Couldn't determine PVID attributes (pvid 0)
[ 31.328939] sja1105 spi0.1: Failed to setup VLAN tagging for port 1: -2
[ 31.335599] ------------[ cut here ]------------
[ 31.340215] WARNING: CPU: 1 PID: 194 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 31.349981] br0: Commit of attribute (id=6) failed.
[ 31.354890] Modules linked in:
[ 31.357942] CPU: 1 PID: 194 Comm: ip Not tainted 5.4.0-rc6-01792-gf4f632e07665-dirty #2062
[ 31.366167] Hardware name: Freescale LS1021A
[ 31.370437] [<c03144dc>] (unwind_backtrace) from [<c030e184>] (show_stack+0x10/0x14)
[ 31.378153] [<c030e184>] (show_stack) from [<c11d1c1c>] (dump_stack+0xe0/0x10c)
[ 31.385437] [<c11d1c1c>] (dump_stack) from [<c034c730>] (__warn+0xf4/0x10c)
[ 31.392373] [<c034c730>] (__warn) from [<c034c7bc>] (warn_slowpath_fmt+0x74/0xb8)
[ 31.399827] [<c034c7bc>] (warn_slowpath_fmt) from [<c11ca204>] (switchdev_port_attr_set_now+0x9c/0xa4)
[ 31.409097] [<c11ca204>] (switchdev_port_attr_set_now) from [<c117036c>] (__br_vlan_filter_toggle+0x6c/0x118)
[ 31.418971] [<c117036c>] (__br_vlan_filter_toggle) from [<c115d010>] (br_changelink+0xf8/0x518)
[ 31.427637] [<c115d010>] (br_changelink) from [<c0f8e9ec>] (__rtnl_newlink+0x3f4/0x76c)
[ 31.435613] [<c0f8e9ec>] (__rtnl_newlink) from [<c0f8eda8>] (rtnl_newlink+0x44/0x60)
[ 31.443329] [<c0f8eda8>] (rtnl_newlink) from [<c0f89f20>] (rtnetlink_rcv_msg+0x2cc/0x51c)
[ 31.451477] [<c0f89f20>] (rtnetlink_rcv_msg) from [<c1008df8>] (netlink_rcv_skb+0xb8/0x110)
[ 31.459796] [<c1008df8>] (netlink_rcv_skb) from [<c1008648>] (netlink_unicast+0x17c/0x1f8)
[ 31.468026] [<c1008648>] (netlink_unicast) from [<c1008980>] (netlink_sendmsg+0x2bc/0x3b4)
[ 31.476261] [<c1008980>] (netlink_sendmsg) from [<c0f43858>] (___sys_sendmsg+0x230/0x250)
[ 31.484408] [<c0f43858>] (___sys_sendmsg) from [<c0f44c84>] (__sys_sendmsg+0x50/0x8c)
[ 31.492209] [<c0f44c84>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 31.500090] Exception stack(0xedf47fa8 to 0xedf47ff0)
[ 31.505122] 7fa0: 00000002b6f2e06000000003beabd6a40000000000000000
[ 31.513265] 7fc0: 00000002b6f2e0605d6e321300000128000000000000000100000006000619c4
[ 31.521405] 7fe0: 00086078beabd6580005edbcb6e7ce68
Since VID 0 is an invalid pvid from the bridge's point of view, let's
add this check in dsa_8021q_restore_pvid to avoid restoring a pvid that
doesn't really exist.
Fixes: 5f33183b7fdf ("net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer [Sat, 16 Nov 2019 15:05:53 +0000 (16:05 +0100)]
seg6: fix skb transport_header after decap_and_validate()
in the receive path (more precisely in ip6_rcv_core()) the
skb->transport_header is set to skb->network_header + sizeof(*hdr). As a
consequence, after routing operations, destination input expects to find
skb->transport_header correctly set to the next protocol (or extension
header) that follows the network protocol. However, decap behaviors (DX*,
DT*) remove the outer IPv6 and SRH extension and do not set again the
skb->transport_header pointer correctly. For this reason, the patch sets
the skb->transport_header to the skb->network_header + sizeof(hdr) in each
DX* and DT* behavior.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: David S. Miller <davem@davemloft.net>
Nishad Kamdar [Sat, 16 Nov 2019 09:40:59 +0000 (15:10 +0530)]
net: stmmac: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style in
header files related to STMicroelectronics based Multi-Gigabit
Ethernet driver. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nishad Kamdar [Sat, 16 Nov 2019 09:20:45 +0000 (14:50 +0530)]
octeontx2-af: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style in
header files related to Marvell OcteonTX2 network devices.
It uses an expilict block comment for the SPDX License
Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 16 Nov 2019 16:20:43 +0000 (08:20 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"11 fixes"
MM fixes and one xz decompressor fix.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/debug.c: PageAnon() is true for PageKsm() pages
mm/debug.c: __dump_page() prints an extra line
mm/page_io.c: do not free shared swap slots
mm/memory_hotplug: fix try_offline_node()
mm,thp: recheck each page before collapsing file THP
mm: slub: really fix slab walking for init_on_free
mm: hugetlb: switch to css_tryget() in hugetlb_cgroup_charge_cgroup()
mm: memcg: switch to css_tryget() in get_mem_cgroup_from_mm()
lib/xz: fix XZ_DYNALLOC to avoid useless memory reallocations
mm: fix trying to reclaim unevictable lru page when calling madvise_pageout
mm: mempolicy: fix the wrong return value and potential pages leak of mbind