We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Johannes Berg [Wed, 7 Jun 2017 07:31:13 +0000 (09:31 +0200)]
iwlwifi: mvm: byte-swap constant instead of variable
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Thu, 8 Jun 2017 07:42:28 +0000 (09:42 +0200)]
iwlwifi: mvm: check family instead of new TX API for workarounds
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Fri, 2 Jun 2017 13:15:53 +0000 (15:15 +0200)]
iwlwifi: reorganize firmware API
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The cast here is wrong. We want to cast the pointer but we accidentally
do a no-op cast of the value. We normally want to set us_nav_upper to
WIFI_NAV_UPPER_US (30000) but because of this bug we instead set it to
184 on little endian systems and 0 on big endian ones.
Fixes: 3c05bedb5fef ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtlwifi: Fix memory leak when firmware request fails
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtlwifi: Uses addr1 instead DA to determine broadcast and multicast addr.
We should check addr1 to indicate a packet as broadcast or multicast
in tx desc. An obvious example, a STA transmit an *unicast* ARP packet
where addr1 and DA are the addresses of AP and broadcast respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Williams [Wed, 12 Jul 2017 16:47:02 +0000 (11:47 -0500)]
ipw2100: don't return positive values to PCI probe on error
Causes the PCI stack to complain, and then eventually call the
PCI remove function, which ipw2100 is not expecting. It then
tries to unregister an already-released netdev and other nasty
things, leading to a panic.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1185518 Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Fri, 21 Jul 2017 09:57:37 +0000 (09:57 +0000)]
mwifiex: disable uapsd in tdls config
Tdls uapsd support capability is default disabled during
tdls setup, correspondingly it should also been disabled
in tdls config.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Zhiyuan Yang <yangzy@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Mon, 10 Jul 2017 07:21:15 +0000 (10:21 +0300)]
mwifiex: usb: unlock on error in mwifiex_usb_tx_aggr_tmo()
We need to unlock if mwifiex_usb_prepare_tx_aggr_skb() fails.
Fixes: a2ca85ad721d ("mwifiex: usb: add timer to flush aggregation packets") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We inited wakeup info at the beginning of mwifiex_add_card, so we need
to uninit it in the error handling.
It's much the same as what we did in: 36908c4 mwifiex: uninit wakeup info when removing device
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Shawn Lin [Thu, 6 Jul 2017 07:50:33 +0000 (15:50 +0800)]
mwifiex: fix compile warning of unused variable
We got a compile warning shows below:
drivers/net/wireless/marvell/mwifiex/sdio.c: In function
'mwifiex_sdio_remove':
drivers/net/wireless/marvell/mwifiex/sdio.c:377:6: warning: variable
'ret' set but not used [-Wunused-but-set-variable]
Per the code, it didn't check if mwifiex_sdio_read_fw_status
finish successfully. We should at least check the return of
mwifiex_sdio_read_fw_status, otherwise the following check of
firmware_stat and adapter->mfg_mode is pointless as the device
is probably dead.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:34 +0000 (18:13 -0700)]
mwifiex: pcie: remove unnecessary 'pdev' check
'card->dev' is initialized once and is never cleared. Drop the
unnecessary "safety" check, as it simply obscures things, and we don't
do this check everywhere (and therefore it's not really "safe").
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:33 +0000 (18:13 -0700)]
mwifiex: pcie: disable device DMA before unmapping/freeing buffers
In testing the mwifiex reset code path, I've noticed KASAN complaining
about some "overwritten poison values" in our RX buffer descriptors.
Because KASAN didn't notice this at the time of a CPU write, this seems
to suggest that the device is writing to this memory.
This makes a little sense, because when resetting, we don't necessarily
expect the device to be responsive, so we don't have a chance to disable
everything cleanly.
We can at least take the precaution of disabling DMA for the device
though, and in my testing that seems to clear up this particular issue.
This patch reorders the removal path so that we disable the device
*before* releasing our last PCIe buffers, and it clears/sets the bus
master feature from the PCI device when resetting.
Along the way, remove the insufficient (and confusing) error path in
mwifiex_pcie_up_dev() (it doesn't unwind things well enough, and it
doesn't propagate its errors upward anyway).
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:32 +0000 (18:13 -0700)]
mwifiex: debugfs: allow card_reset() to cancel things
The card_reset() implementation should be setting our state flags and
cancelling commands for us (i.e., in mwifiex_shutdown_drv()), so let's
not do it here.
Also, this debugfs file is useful for testing and debugging the reset
feature, so we shouldn't do extra preparatory steps here, as that might
cause different reset behavior, which could either cause new bugs or
paper over existing ones that this debug feature should otherwise help
us catch.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:31 +0000 (18:13 -0700)]
mwifiex: pcie: unify MSI-X / non-MSI-X interrupt process
After removing the interrupt loop in commit 5d5ddb5e0d9b ("mwifiex:
pcie: don't loop/retry interrupt status checks"), there is practically
zero difference between mwifiex_process_pcie_int() (which handled legacy
PCI interrupts and MSI interrupts) and mwifiex_process_msix_int() (which
handled MSI-X interrupts). Let's add the one relevant line to
mwifiex_process_pcie_int() and kill the copy-and-paste.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:30 +0000 (18:13 -0700)]
mwifiex: pcie: remove unnecessary masks
After removing the interrupt loop in commit 5d5ddb5e0d9b ("mwifiex:
pcie: don't loop/retry interrupt status checks"), we don't need to keep
track of the cleared interrupts (actually, we didn't need to do that
before, but we *really* don't need to now).
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:25 +0000 (18:13 -0700)]
mwifiex: fix misnomers in mwifiex_free_lock_list()
Despite the name (and meticulous comments), this function frees no
memory and does not touch any locks. All it does is "delete" the list
heads -- which just means they'll be dangling, and we'll need to re-init
them if we use them again.
It seems like this code would work OK as a sort of canary for using the
list after we've torn everything down, so it's fine to keep the code;
let's just get the name and comments to match what's actually happening.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:24 +0000 (18:13 -0700)]
mwifiex: ensure "disable auto DS" struct is initialized
The .idle_time field *should* be unused, but technically, we're allowing
unitialized stack garbage to pass all the way through to the firmware
host command. Let's zero it out instead.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:23 +0000 (18:13 -0700)]
mwifiex: fixup init_channel_scan_gap error case
In reading through _mwifiex_fw_dpc(), I noticed that after we've
registered our wiphy, we still have error paths that don't free it back
up. Let's do that.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:22 +0000 (18:13 -0700)]
mwifiex: don't short-circuit netdev notifiers on interface deletion
When we leave the delete interface function, there are still netdev
hooks that might try to process the device. We're short-circuiting some
of that by changing the interface type and clearing ieee80211_ptr. This
means we skip NETDEV_UNREGISTER_FINAL in cfg80211. Fortunately, that is
currently a no-op.
We don't need most of the cleanup here anyway:
* the connection state will get (un)set as part of the disconnect
process (which cfg80211 already initiates for us)
* the interface type doesn't actually need to be cleared at all (it'll
trigger a WARN_ON() in cfg80211 if we do)
* the iee80211_ptr isn't really "ours" to clear anyway
So stop resetting those 3 things.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:21 +0000 (18:13 -0700)]
mwifiex: unregister wiphy before freeing resources
It's possible for some control interfaces (e.g., scans, set freq) to be
active after we've stopped our main work queue and the netif TX queues.
These don't get completely shut out until we've unregistered the wdevs
and wiphy.
So let's only free command buffers and poison our lists after
wiphy_unregister().
This resolves various use-after-free issues seen when resetting the
device.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:20 +0000 (18:13 -0700)]
mwifiex: re-register wiphy across reset
In general, it's helpful to use the same code for device removal as for
device reset, as this tends to have fewer bugs. Let's move the wiphy
unregistration code into the common reset and removal code.
In particular, it's very hard to properly handle the reset sequence when
something fails. Currently, if mwifiex_reinit_sw() fails, we've failed
to unregister the associated wiphy, and so running something as simple
as "iw phy" can trigger an OOPS, as the wiphy still has hooks back into
freed mwifiex data structures. For example, KASAN complained:
[... see reset fail for other reasons ...]
[ 1184.821158] mwifiex_pcie 0000:01:00.0: info: dnld wifi firmware from 174948 bytes
[ 1186.870914] mwifiex_pcie 0000:01:00.0: info: FW download over, size 608396 bytes
[ 1187.685990] mwifiex_pcie 0000:01:00.0: WLAN FW is active
[ 1187.692673] mwifiex_pcie 0000:01:00.0: cmd_wait_q terminated: -512
[ 1187.699075] mwifiex_pcie 0000:01:00.0: info: _mwifiex_fw_dpc: unregister device
[ 1187.713476] mwifiex: Failed to bring up adapter: -5
[ 1187.718644] mwifiex_pcie 0000:01:00.0: reinit failed: -5
Brian Norris [Tue, 25 Jul 2017 01:13:19 +0000 (18:13 -0700)]
mwifiex: pcie: don't allow cmd buffer reuse after reset
In rogue cases (due to other bugs) it's possible we try to process an
old command response *after* resetting the device. This could trigger a
double-free (or the SKB can get reallocated elsewhere...causing other
memory corruptions) in mwifiex_pcie_process_cmd_complete().
For safety (and symmetry) let's always NULL out the command buffer as we
free it up. We're already doing this for the command response buffer.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 25 Jul 2017 01:13:18 +0000 (18:13 -0700)]
mwifiex: reset interrupt status across device reset
When resetting the device, we might have queued up interrupts that
didn't get a chance to finish processing. We really don't need to handle
them at this point; we just want to make sure they don't cause us to try
to process old commands from before the device was reset.
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIe FLR code was added, it explicitly copy-and-pasted much of
mwifiex_remove_card() into mwifiex_shutdown_sw(). This is unnecessary,
as almost all of the code should be reused.
Let's reunite what we can for now.
The only functional changes for now:
* call netif_device_detach() in the remove() code path -- this wasn't
done before, but it really should be a no-op, when the device is
getting totally unregistered soon anyway
* call the ->down_dev() driver callback only after we've finished all
SW teardown -- this should have no significant effect, since the only
user (pcie.c) does very minimal work there, and it doesn't matter
that we reorder this
Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Below regulatory changes are included this patch
* Country code is saved as it will be used in bgscan.
* Region codes are mapped according to RSI region codes.
* Radar flag settings are moved under the check if 5GHZ band
is enabled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device specific descriptor for each TX packet is prepared on top of
skb data address. This descriptor should be pulled out before
indicating the TX status to mac80211.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_channel is modified to use common
descriptor structure. Also DFS channel indication to firmware
is added in the descriptor for dfs channels configuration.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: remove unnecessary check for 802.11 management packet
The function rsi_mgmt_pkt_to_core() is for passing the 802.11
management frames to mac80211. So, it is unnecessary to check
again for the frame type 802.11 management in this function.
It can be checked before passing to this function.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: Update in tx command frame radio capabilities
Radio capabilities frame is updated to use common descriptor
structure. Also, few changes to this frame is done like hardware
queues are increase to 12 from 8, default channel number is included.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: immediate wakeup bit and priority for TX command packets
For all TX command packets immediate wakeup bit needs to be
set in descriptor. This will make sure device will wakeup if it
is in any sleep state. Priority of the packet is also set.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: add common structures needed for command packets
All internal management packets (command packets) use some common
fields and some packet specific fields for packet descriptors.
This patch adds some common structures which are needed for all
command packets.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer firmware sends information about number of blocks through
interrupt only. We don't need to read extra register for this.
This patch adds needed driver changes for this enhancment. The
change here is backward compatible
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO host is already claimed in our interrupt handler. Some lower
level APIs claims host while performing SDIO read or write operations.
Let's use sdio_irq_task variable to check if we are in interrupt
context and claim/release the host accordingly.
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB headroom is added while submitting the data to URB as per
firmware's requirement. This logic is moved to rsi_usb_card_write() so
that caller need not worry about it.
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for this
reset configuration for USB.
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes it's observed that we get interrupt/Rx frame when device is
already detached from mac80211. In this case couple of error messages
are displayed in dmesg log. This patch corrects the order so that
disconnection will happen cleanly
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for
this reset configuration for SDIO.
Signed-off-by: Karun Eagalapati <karun256@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
EEPROM read frame is sent during device initialization to read mac address.
The format of the frame is modified in firmware to include eeprom length
and offset. This frame does not return firmware version now. Also same
frame is sent again to read rf type and band information.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever new fsm_state enum element is added, fsm_state array
also needs to be updated. If this change is missed, we may end
up doing invalid access in array. BUILD_BUG_ON check will help
to avoid this problem.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cong Wang [Thu, 6 Jul 2017 22:00:37 +0000 (15:00 -0700)]
wl1251: add a missing spin_lock_init()
This fixes the following kernel warning:
[ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
[ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
.owner_cpu: 0
[ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W 4.12.0-03002-gec979a4-dirty #40
[ 5668.772796] Hardware name: Nokia RX-51 board
[ 5668.773071] Workqueue: phy1 wl1251_irq_work
[ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
(show_stack+0x10/0x14)
[ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
(do_raw_spin_lock+0x6c/0xa0)
[ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
(_raw_spin_lock_irqsave+0x10/0x18)
[ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
(wl1251_op_tx+0x38/0x5c)
[ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
(ieee80211_tx_frags+0x188/0x1c0)
[ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
(__ieee80211_tx+0x6c/0x130)
[ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
(ieee80211_tx+0xdc/0x104)
[ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
(__ieee80211_subif_start_xmit+0x454/0x8c8)
[ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
[<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
[ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
[<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...
by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Florian Fainelli [Fri, 30 Jun 2017 19:02:57 +0000 (12:02 -0700)]
bcma: gpio: Correct number of GPIOs for BCM53573
Broadcom BCM53573 SoCs actually have 32 GPIOs, and not 16.
Fixes: 3f37ec79dd21 ("bcma: support BCM53573 series of wireless SoCs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>