qed: Do not add VLAN 0 tag to untagged frames in multi-function mode.
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Fix populating the invalid stag value in multi function mode.
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Hellstrom [Fri, 14 Sep 2018 07:24:19 +0000 (09:24 +0200)]
drm/vmwgfx: Fix buffer object eviction
Commit 19be55701071 ("drm/ttm: add operation ctx to ttm_bo_validate v2")
introduced a regression where the vmwgfx driver refused to evict a
buffer that was still busy instead of waiting for it to become idle.
Fix this.
Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Christian König <christian.koenig@amd.com>
drm/vmwgfx: limit screen size to stdu_max during check_modeset
For STDU individual screen target size is limited by
SVGA_REG_SCREENTARGET_MAX_WIDTH/HEIGHT registers so add that limit
during atomic check_modeset.
An additional limit is placed in the update_layout ioctl to avoid
requesting layouts that current user-space typically can't support.
Also modified the comments to reflect current limitation on topology.
Signed-off-by: Deepak Rawat <drawat@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
drm/vmwgfx: don't check for old_crtc_state enable status
During atomic check to prepare the new topology no need to check if
old_crtc_state was enabled or not. This will cause atomic_check to fail
because due to connector routing a crtc can be in atomic_state even if
there was no change to enable status.
powerpc/powernv/ioda2: Reduce upper limit for DMA window size (again)
mpe: This was fixed originally in commit d3d4ffaae439
("powerpc/powernv/ioda2: Reduce upper limit for DMA window size"), but
contrary to what the merge commit says was inadvertently lost by me in
commit ce57c6610cc2 ("Merge branch 'topic/ppc-kvm' into next") which
brought in changes that moved the code to a new file. So reapply it to
the new file.
Original commit message follows:
We use PHB in mode1 which uses bit 59 to select a correct DMA window.
However there is mode2 which uses bits 59:55 and allows up to 32 DMA
windows per a PE.
Even though documentation does not clearly specify that, it seems that
the actual hardware does not support bits 59:55 even in mode1, in
other words we can create a window as big as 1<<58 but DMA simply
won't work.
This reduces the upper limit from 59 to 55 bits to let the userspace
know about the hardware limits.
Fixes: ce57c6610cc2 ("Merge branch 'topic/ppc-kvm' into next") Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Antoine Tenart [Wed, 19 Sep 2018 13:29:06 +0000 (15:29 +0200)]
net: mvneta: fix the Rx desc buffer DMA unmapping
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 19 Sep 2018 13:02:07 +0000 (15:02 +0200)]
ip6_tunnel: be careful when accessing the inner header
the ip6 tunnel xmit ndo assumes that the processed skb always
contains an ip[v6] header, but syzbot has found a way to send
frames that fall short of this assumption, leading to the following splat:
This change addresses the issue adding the needed check before
accessing the inner header.
The ipv4 side of the issue is apparently there since the ipv4 over ipv6
initial support, and the ipv6 side predates git history.
Fixes: c4d3efafcc93 ("[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+3fde91d4d394747d6db4@syzkaller.appspotmail.com Tested-by: Alexander Potapenko <glider@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Sep 2018 03:32:46 +0000 (20:32 -0700)]
Merge tag 'batadv-net-for-davem-20180919' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
pull request for net: batman-adv 2018-09-19
here are some bugfixes which we would like to see integrated into net.
We forgot to bump the version number in the last round for net-next, so
the belated patch to do that is included - we hope you can adopt it.
This will most likely create a merge conflict later when merging into
net-next with this rounds net-next patchset, but net-next should keep
the 2018.4 version[1].
Dave Airlie [Thu, 20 Sep 2018 00:00:31 +0000 (10:00 +1000)]
Merge tag 'drm-misc-fixes-2018-09-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.19-rc5:
- Fix crash in vgem in drm_drv_uses_atomic_modeset.
- Allow atomic drivers that don't set DRIVER_ATOMIC to create debugfs entries.
- Fix compiler warning for unused connector_funcs.
- Fix null pointer deref on UDL unplug.
- Disable DRM support for sun4i's R40 for now.
(Not all patches went in for v4.19, so it has to wait a cycle.)
- NULL-terminate the of_device_id table in pl111.
- Make sure vc4 NV12 planar format works when displaying an unscaled fb.
Drew Schmitt [Mon, 20 Aug 2018 17:32:15 +0000 (10:32 -0700)]
KVM: x86: Control guest reads of MSR_PLATFORM_INFO
Add KVM_CAP_MSR_PLATFORM_INFO so that userspace can disable guest access
to reads of MSR_PLATFORM_INFO.
Disabling access to reads of this MSR gives userspace the control to "expose"
this platform-dependent information to guests in a clear way. As it exists
today, guests that read this MSR would get unpopulated information if userspace
hadn't already set it (and prior to this patch series, only the CPUID faulting
information could have been populated). This existing interface could be
confusing if guests don't handle the potential for incorrect/incomplete
information gracefully (e.g. zero reported for base frequency).
Signed-off-by: Drew Schmitt <dasch@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drew Schmitt [Mon, 20 Aug 2018 17:32:14 +0000 (10:32 -0700)]
KVM: x86: Turbo bits in MSR_PLATFORM_INFO
Allow userspace to set turbo bits in MSR_PLATFORM_INFO. Previously, only
the CPUID faulting bit was settable. But now any bit in
MSR_PLATFORM_INFO would be settable. This can be used, for example, to
convey frequency information about the platform on which the guest is
running.
Signed-off-by: Drew Schmitt <dasch@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nVMX x86: Check VPID value on vmentry of L2 guests
According to section "Checks on VMX Controls" in Intel SDM vol 3C, the
following check needs to be enforced on vmentry of L2 guests:
If the 'enable VPID' VM-execution control is 1, the value of the
of the VPID VM-execution control field must not be 0000H.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Krish Sadhukhan [Fri, 24 Aug 2018 00:03:03 +0000 (20:03 -0400)]
nVMX x86: check posted-interrupt descriptor addresss on vmentry of L2
According to section "Checks on VMX Controls" in Intel SDM vol 3C,
the following check needs to be enforced on vmentry of L2 guests:
- Bits 5:0 of the posted-interrupt descriptor address are all 0.
- The posted-interrupt descriptor address does not set any bits
beyond the processor's physical-address width.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Reviewed-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: nVMX: Wake blocked vCPU in guest-mode if pending interrupt in virtual APICv
In case L1 do not intercept L2 HLT or enter L2 in HLT activity-state,
it is possible for a vCPU to be blocked while it is in guest-mode.
According to Intel SDM 26.6.5 Interrupt-Window Exiting and
Virtual-Interrupt Delivery: "These events wake the logical processor
if it just entered the HLT state because of a VM entry".
Therefore, if L1 enters L2 in HLT activity-state and L2 has a pending
deliverable interrupt in vmcs12->guest_intr_status.RVI, then the vCPU
should be waken from the HLT state and injected with the interrupt.
In addition, if while the vCPU is blocked (while it is in guest-mode),
it receives a nested posted-interrupt, then the vCPU should also be
waken and injected with the posted interrupt.
To handle these cases, this patch enhances kvm_vcpu_has_events() to also
check if there is a pending interrupt in L2 virtual APICv provided by
L1. That is, it evaluates if there is a pending virtual interrupt for L2
by checking RVI[7:4] > VPPR[7:4] as specified in Intel SDM 29.2.1
Evaluation of Pending Interrupts.
Note that this also handles the case of nested posted-interrupt by the
fact RVI is updated in vmx_complete_nested_posted_interrupt() which is
called from kvm_vcpu_check_block() -> kvm_arch_vcpu_runnable() ->
kvm_vcpu_running() -> vmx_check_nested_events() ->
vmx_complete_nested_posted_interrupt().
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions
kvm_load_guest_fpu()
kvm_put_guest_fpu()
are only used locally, make them static. This requires also that both
functions are moved because they are used before their implementation.
Those functions were exported (via EXPORT_SYMBOL) before commit e5bb40251a920 ("KVM: Drop kvm_{load,put}_guest_fpu() exports").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These structures are going to be used from KVM code so let's make
their names reflect their Hyper-V origin.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Roman Kagan <rkagan@virtuozzo.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: VMX: use preemption timer to force immediate VMExit
A VMX preemption timer value of '0' is guaranteed to cause a VMExit
prior to the CPU executing any instructions in the guest. Use the
preemption timer (if it's supported) to trigger immediate VMExit
in place of the current method of sending a self-IPI. This ensures
that pending VMExit injection to L1 occurs prior to executing any
instructions in the guest (regardless of nesting level).
When deferring VMExit injection, KVM generates an immediate VMExit
from the (possibly nested) guest by sending itself an IPI. Because
hardware interrupts are blocked prior to VMEnter and are unblocked
(in hardware) after VMEnter, this results in taking a VMExit(INTR)
before any guest instruction is executed. But, as this approach
relies on the IPI being received before VMEnter executes, it only
works as intended when KVM is running as L0. Because there are no
architectural guarantees regarding when IPIs are delivered, when
running nested the INTR may "arrive" long after L2 is running e.g.
L0 KVM doesn't force an immediate switch to L1 to deliver an INTR.
For the most part, this unintended delay is not an issue since the
events being injected to L1 also do not have architectural guarantees
regarding their timing. The notable exception is the VMX preemption
timer[1], which is architecturally guaranteed to cause a VMExit prior
to executing any instructions in the guest if the timer value is '0'
at VMEnter. Specifically, the delay in injecting the VMExit causes
the preemption timer KVM unit test to fail when run in a nested guest.
Note: this approach is viable even on CPUs with a broken preemption
timer, as broken in this context only means the timer counts at the
wrong rate. There are no known errata affecting timer value of '0'.
[1] I/O SMIs also have guarantees on when they arrive, but I have
no idea if/how those are emulated in KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Use a hook for SVM instead of leaving the default in x86.c - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: VMX: modify preemption timer bit only when arming timer
Provide a singular location where the VMX preemption timer bit is
set/cleared so that future usages of the preemption timer can ensure
the VMCS bit is up-to-date without having to modify unrelated code
paths. For example, the preemption timer can be used to force an
immediate VMExit. Cache the status of the timer to avoid redundant
VMREAD and VMWRITE, e.g. if the timer stays armed across multiple
VMEnters/VMExits.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: VMX: immediately mark preemption timer expired only for zero value
A VMX preemption timer value of '0' at the time of VMEnter is
architecturally guaranteed to cause a VMExit prior to the CPU
executing any instructions in the guest. This architectural
definition is in place to ensure that a previously expired timer
is correctly recognized by the CPU as it is possible for the timer
to reach zero and not trigger a VMexit due to a higher priority
VMExit being signalled instead, e.g. a pending #DB that morphs into
a VMExit.
Whether by design or coincidence, commit f4124500c2c1 ("KVM: nVMX:
Fully emulate preemption timer") special cased timer values of '0'
and '1' to ensure prompt delivery of the VMExit. Unlike '0', a
timer value of '1' has no has no architectural guarantees regarding
when it is delivered.
Modify the timer emulation to trigger immediate VMExit if and only
if the timer value is '0', and document precisely why '0' is special.
Do this even if calibration of the virtual TSC failed, i.e. VMExit
will occur immediately regardless of the frequency of the timer.
Making only '0' a special case gives KVM leeway to be more aggressive
in ensuring the VMExit is injected prior to executing instructions in
the nested guest, and also eliminates any ambiguity as to why '1' is
a special case, e.g. why wasn't the threshold for a "short timeout"
set to 10, 100, 1000, etc...
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Lei Yang [Wed, 29 Aug 2018 07:04:08 +0000 (15:04 +0800)]
kvm: selftests: use -pthread instead of -lpthread
I run into the following error
testing/selftests/kvm/dirty_log_test.c:285: undefined reference to `pthread_create'
testing/selftests/kvm/dirty_log_test.c:297: undefined reference to `pthread_join'
collect2: error: ld returned 1 exit status
my gcc version is gcc version 4.8.4
"-pthread" would work everywhere
Signed-off-by: Lei Yang <Lei.Yang@windriver.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wei Yang [Fri, 7 Sep 2018 11:59:47 +0000 (19:59 +0800)]
KVM: x86: don't reset root in kvm_mmu_setup()
Here is the code path which shows kvm_mmu_setup() is invoked after
kvm_mmu_create(). Since kvm_mmu_setup() is only invoked in this code path,
this means the root_hpa and prev_roots are guaranteed to be invalid. And
it is not necessary to reset it again.
x86/kvm/lapic: always disable MMIO interface in x2APIC mode
When VMX is used with flexpriority disabled (because of no support or
if disabled with module parameter) MMIO interface to lAPIC is still
available in x2APIC mode while it shouldn't be (kvm-unit-tests):
PASS: apic_disable: Local apic enabled in x2APIC mode
PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set
FAIL: apic_disable: *0xfee00030: 50014
The issue appears because we basically do nothing while switching to
x2APIC mode when APIC access page is not used. apic_mmio_{read,write}
only check if lAPIC is disabled before proceeding to actual write.
When APIC access is virtualized we correctly manipulate with VMX controls
in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes
in x2APIC mode so there's no issue.
Disabling MMIO interface seems to be easy. The question is: what do we
do with these reads and writes? If we add apic_x2apic_mode() check to
apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will
go to userspace. When lAPIC is in kernel, Qemu uses this interface to
inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This
somehow works with disabled lAPIC but when we're in xAPIC mode we will
get a real injected MSI from every write to lAPIC. Not good.
The simplest solution seems to be to just ignore writes to the region
and return ~0 for all reads when we're in x2APIC mode. This is what this
patch does. However, this approach is inconsistent with what currently
happens when flexpriority is enabled: we allocate APIC access page and
create KVM memory region so in x2APIC modes all reads and writes go to
this pre-allocated page which is, btw, the same for all vCPUs.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently there are two separate ways to free the OPP table based on how
it is created in the first place.
We call _dev_pm_opp_remove_table() to free the static and/or dynamic
OPP, OPP list devices, etc. This is done for the case where the OPP
table is added while initializing the OPPs, like via the path
dev_pm_opp_of_add_table().
We also call dev_pm_opp_put_opp_table() in some cases which eventually
frees the OPP table structure once the reference count reaches 0. This
is used by the first case as well as other cases like
dev_pm_opp_set_regulators() where the OPPs aren't necessarily
initialized at this point.
This whole thing is a bit unclear and messy and obstruct any further
cleanup/fixup of OPP core.
This patch tries to streamline this by keeping a single path for OPP
table destruction, i.e. dev_pm_opp_put_opp_table().
All the cleanup happens in _opp_table_kref_release() now after the
reference count reaches 0. _dev_pm_opp_remove_table() is removed as it
isn't required anymore.
We don't drop the reference to the OPP table after creating it from
_of_add_opp_table_v{1|2}() anymore and the same is dropped only when we
try to remove them.
OPP: Don't remove dynamic OPPs from _dev_pm_opp_remove_table()
Only one platform was depending on this feature and it is already
updated now. Stop removing dynamic OPPs from _dev_pm_opp_remove_table().
This simplifies lot of paths and removes unnecessary parameters.
cpufreq: mvebu: Remove OPPs using dev_pm_opp_remove()
dev_pm_opp_cpumask_remove_table() is going to change in the next commit
and will not remove dynamic OPPs automatically. They must be removed
with a call to dev_pm_opp_remove().
The static OPPs don't always get freed with the OPP table, it can happen
before that as well. For example, if the OPP table is first created
using helpers like dev_pm_opp_set_supported_hw() and the OPPs are
created at a later point. Now when the OPPs are removed, the OPP table
stays until the time dev_pm_opp_put_supported_hw() is called.
Later patches will streamline the freeing of OPP table and that requires
the static OPPs to get freed with help of a separate kernel reference.
This patch prepares for that by creating a separate kref for static OPPs
list.
Viresh Kumar [Thu, 2 Aug 2018 08:53:09 +0000 (14:23 +0530)]
OPP: Don't take OPP table's kref for static OPPs
The reference count is only required to be incremented for every call
that may lead to adding the OPP table. For static OPPs the same should
be done from the parent routine which adds all static OPPs together and
so only one refcount for all static OPPs.
Update code to reflect that.
The refcount is incremented every time a dynamic OPP is created (as that
can lead to creating the OPP table) and the same is dropped when the OPP
is removed.
Viresh Kumar [Thu, 14 Jun 2018 06:34:43 +0000 (12:04 +0530)]
OPP: Parse OPP table's DT properties from _of_init_opp_table()
Parse the DT properties present in the OPP table from
_of_init_opp_table(), which is a dedicated routine for DT parsing.
Minor relocation of helpers is required for this.
It is possible now for _managed_opp() to return a partially initialized
OPP table if the OPP table is created via the helpers like
dev_pm_opp_set_supported_hw() and we need another flag to indicate if
the static OPP are already parsed or not to make sure we don't
incorrectly skip initializing the static OPPs.
This is a preparatory patch required for the next commit which will
start using OPP table's node pointer in _of_init_opp_table(), which
requires the index in order to read the OPP table's phandle.
This commit adds the index argument in the call chains in order to get
it delivered to _of_init_opp_table().
Viresh Kumar [Fri, 3 Aug 2018 01:35:21 +0000 (07:05 +0530)]
OPP: Protect dev_list with opp_table lock
The dev_list needs to be protected with a lock, else we may have
simultaneous access (addition/removal) to it and that would be racy.
Extend scope of the opp_table lock to protect dev_list as well.
OPP: Don't try to remove all OPP tables on failure
dev_pm_opp_of_cpumask_add_table() creates the OPP table for all CPUs
present in the cpumask and on errors it should revert all changes it has
done.
It actually is doing a bit more than that. On errors, it tries to free
all the OPP tables, even the one it hasn't created yet. This may also
end up freeing the OPP tables which were created from separate path,
like dev_pm_opp_set_supported_hw().
OPP: Free OPP table properly on performance state irregularities
The OPP table was freed, but not the individual OPPs which is done from
_dev_pm_opp_remove_table(). Fix it by calling _dev_pm_opp_remove_table()
as well.
Cc: 4.18 <stable@vger.kernel.org> # v4.18 Fixes: 3ba98324e81a ("PM / OPP: Get performance state using genpd helper") Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Jakub Kicinski [Tue, 18 Sep 2018 17:13:59 +0000 (10:13 -0700)]
tools: bpf: fix license for a compat header file
libc_compat.h is used by libbpf so make sure it's licensed under
LGPL or BSD license. The license change should be OK, I'm the only
author of the file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
Use different loop variables for the inner and outer loop. This avoids
that an infinite loop occurs if there are more RDMA channels than
target->req_ring_size.
Fixes: d92c0da71a35 ("IB/srp: Add multichannel support") Cc: <stable@vger.kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
xen: issue warning message when out of grant maptrack entries
When a driver domain (e.g. dom0) is running out of maptrack entries it
can't map any more foreign domain pages. Instead of silently stalling
the affected domUs issue a rate limited warning in this case in order
to make it easier to detect that situation.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Sync syscall to DAX file needs to flush processor cache, but it
currently does not flush to existing DAX files. This is because
'ext2_da_aops' is set to address_space_operations of existing DAX
files, instead of 'ext2_dax_aops', since S_DAX flag is set after
ext2_set_aops() in the open path.
Similar to ext4, change ext2_iget() to initialize i_flags before
ext2_set_aops().
Fixes: fb094c90748f ("ext2, dax: introduce ext2_dax_aops") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Suggested-by: Jan Kara <jack@suse.cz> Cc: Jan Kara <jack@suse.cz> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Andreas Dilger <adilger.kernel@dilger.ca> Cc: <stable@vger.kernel.org> Signed-off-by: Jan Kara <jack@suse.cz>
Merge tag 'perf-urgent-for-mingo-4.19-20180918' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix the build on !_GNU_SOURCE libc systems such as Alpine Linux/musl
libc due to usage of strerror_r glibc variant on libbpf (Arnaldo Carvalho de Melo)
- Fix out-of-tree asciidoctor man page generation (Ben Hutchings)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Crypto stuff from Herbert:
"This push fixes a potential boot hang in ccp and an incorrect
CPU capability check in aegis/morus on x86."
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/aegis,morus - Do not require OSXSAVE for SSE2
crypto: ccp - add timeout support in the SEV command
Merge tag 'trace-v4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Steven writes:
"Vaibhav Nagarnaik found that modifying the ring buffer size could cause
a huge latency in the system because it does a while loop to free pages
without releasing the CPU (on non preempt kernels). In a case where there
are hundreds of thousands of pages to free it could actually cause a system
stall. A properly place cond_resched() solves this issue."
Merge tag 'platform-drivers-x86-v4.19-2' of git://git.infradead.org/linux-platform-drivers-x86
Darren writes:
"platform-drivers-x86 for v4.19-2
Free allocated ACPI buffers in two drivers.
The following is an automated git shortlog grouped by driver:
alienware-wmi:
- Correct a memory leak
dell-smbios-wmi:
- Correct a memory leak"
* tag 'platform-drivers-x86-v4.19-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: alienware-wmi: Correct a memory leak
platform/x86: dell-smbios-wmi: Correct a memory leak
====================
ipv6: fix issues on accessing fib6_metrics
The latest fix on the memory leak of fib6_metrics still causes
use-after-free.
This patch series first revert the previous fix and propose a new fix
that is more inline with ipv4 logic and is tested to fix the
use-after-free issue reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Tue, 18 Sep 2018 20:45:00 +0000 (13:45 -0700)]
ipv6: fix memory leak on dst->_metrics
When dst->_metrics and f6i->fib6_metrics share the same memory, both
take reference count on the dst_metrics structure. However, when dst is
destroyed, ip6_dst_destroy() only invokes dst_destroy_metrics_generic()
which does not take care of READONLY metrics and does not release refcnt.
This causes memory leak.
Similar to ipv4 logic, the fix is to properly release refcnt and free
the memory space pointed by dst->_metrics if refcnt becomes 0.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change causes use-after-free on dst->_metrics.
The crash trace looks like this:
[ 97.763269] BUG: KASAN: use-after-free in ip6_mtu+0x116/0x140
[ 97.769038] Read of size 4 at addr ffff881781d2cf84 by task svw_NetThreadEv/8801
Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 18 Sep 2018 15:48:53 +0000 (16:48 +0100)]
sfp: fix oops with ethtool -m
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 18 Sep 2018 14:58:47 +0000 (16:58 +0200)]
net: mvpp2: fix a txq_done race condition
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09e2 ("net: mvpp2: replace TX coalescing interrupts with hrtimer") Reported-by: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kernel_sendmsg can return a negative
error code.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don't check a listen socket for pending urgent data in smc_poll().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: enable fallback for connection abort in state INIT
If a linkgroup is terminated abnormally already due to failing
LLC CONFIRM LINK or LLC ADD LINK, fallback to TCP is still possible.
In this case do not switch to state SMC_PEERABORTWAIT and do not set
sk_err.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For a failing smc_listen_rdma_finish() smc_listen_decline() is
called. If fallback is possible, the new socket is already enqueued
to be accepted in smc_listen_decline(). Avoid enqueuing a second time
afterwards in this case, otherwise the smc_create_lgr_pending lock
is released twice:
[ 373.463976] WARNING: bad unlock balance detected!
[ 373.463978] 4.18.0-rc7+ #123 Tainted: G O
[ 373.463979] -------------------------------------
[ 373.463980] kworker/1:1/30 is trying to release lock (smc_create_lgr_pending) at:
[ 373.463990] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.463991] but there are no more locks to release!
[ 373.463991]
other info that might help us debug this:
[ 373.463993] 2 locks held by kworker/1:1/30:
[ 373.463994] #0: 00000000772cbaed ((wq_completion)"events"){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464000] #1: 000000003ad0894a ((work_completion)(&new_smc->smc_listen_work)){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464003]
stack backtrace:
[ 373.464005] CPU: 1 PID: 30 Comm: kworker/1:1 Kdump: loaded Tainted: G O 4.18.0-rc7uschi+ #123
[ 373.464007] Hardware name: IBM 2827 H43 738 (LPAR)
[ 373.464010] Workqueue: events smc_listen_work [smc]
[ 373.464011] Call Trace:
[ 373.464015] ([<0000000000114100>] show_stack+0x60/0xd8)
[ 373.464019] [<0000000000a8c9bc>] dump_stack+0x9c/0xd8
[ 373.464021] [<00000000001dcaf8>] print_unlock_imbalance_bug+0xf8/0x108
[ 373.464022] [<00000000001e045c>] lock_release+0x114/0x4f8
[ 373.464025] [<0000000000aa87fa>] __mutex_unlock_slowpath+0x4a/0x300
[ 373.464027] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.464029] [<0000000000197a68>] process_one_work+0x2a8/0x6b0
[ 373.464030] [<0000000000197ec2>] worker_thread+0x52/0x410
[ 373.464033] [<000000000019fd0e>] kthread+0x15e/0x178
[ 373.464035] [<0000000000aaf58a>] kernel_thread_starter+0x6/0xc
[ 373.464052] [<0000000000aaf584>] kernel_thread_starter+0x0/0xc
[ 373.464054] INFO: lockdep is turned off.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In state SMC_INIT smc_poll() delegates polling to the internal
CLC socket. This means, once the connect worker has finished
its kernel_connect() step, the poll wake-up may occur. This is not
intended. The wake-up should occur from the wake up call in
smc_connect_work() after __smc_connect() has finished.
Thus in state SMC_INIT this patch now calls sock_poll_wait() on the
main SMC socket.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: \91nvm_param.dir_type\92 may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: emac: fix fixed-link setup for the RTL8363SB switch
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to ETSI TS 102 622 specification chapter 4.4 pipe identifier
is 7 bits long which allows for 128 unique pipe IDs. Because
NFC_HCI_MAX_PIPES is used as the number of pipes supported and not
as the max pipe ID, its value should be 128 instead of 127.
nfc_hci_recv_from_llc extracts pipe ID from packet header using
NFC_HCI_FRAGMENT(0x7F) mask which allows for pipe ID value of 127.
Same happens when NCI_HCP_MSG_GET_PIPE() is being used. With
pipes array having only 127 elements and pipe ID of 127 the OOB memory
access will result.
Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Allen Pais <allen.pais@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
NFC: Fix possible memory corruption when handling SHDLC I-Frame commands
When handling SHDLC I-Frame commands "pipe" field used for indexing
into an array should be checked before usage. If left unchecked it
might access memory outside of the array of size NFC_HCI_MAX_PIPES(127).
Malformed NFC HCI frames could be injected by a malicious NFC device
communicating with the device being attacked (remote attack vector),
or even by an attacker with physical access to the I2C bus such that
they could influence the data transfers on that bus (local attack vector).
skb->data is controlled by the attacker and has only been sanitized in
the most trivial ways (CRC check), therefore we can consider the
create_info struct and all of its members to tainted. 'create_info->pipe'
with max value of 255 (uint8) is used to take an offset of the
hdev->pipes array of 127 elements which can lead to OOB write.
Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Allen Pais <allen.pais@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Kevin Deus <kdeus@google.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: pmtu: properly redirect stderr to /dev/null
The cleanup function uses "$CMD 2 > /dev/null", which doesn't actually
send stderr to /dev/null, so when the netns doesn't exist, the error
message is shown. Use "2> /dev/null" instead, so that those messages
disappear, as was intended.
Fixes: d1f1b9cbf34c ("selftests: net: Introduce first PMTU test") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Mon, 17 Sep 2018 08:22:57 +0000 (09:22 +0100)]
net: stmmac: Fixup the tail addr setting in xmit path
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Fixes: f748be531d70 ("stmmac: support new GMAC4") Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Mon, 17 Sep 2018 08:22:56 +0000 (09:22 +0100)]
net: stmmac: Rework coalesce timer and fix multi-queue races
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Fixes: ce736788e8a ("net: stmmac: adding multiple buffers for TX") Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds wakeup function support for egalax touch
screen, if "wakeup-source" is added to device tree's egalax
touch screen node, the wakeup function will be enabled, and
egalax touch screen will be able to wakeup system from suspend.
MAINTAINERS: Update PPC contacts for PCI core error handling
The original PCI error recovery functionality was for the powerpc-specific
IBM EEH feature. PCIe subsequently added some similar features, including
AER and DPC, that can be used on any architecture.
We want the generic PCI core error handling support to work with all of
these features. Driver error recovery callbacks should be independent of
which feature the platform provides.
Add the generic PCI core error recovery files to the powerpc EEH
MAINTAINERS entry so the powerpc folks will be copied on changes to the
generic PCI error handling strategy.
Add Sam and Oliver as maintainers for this area.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Russell Currey <ruscur@russell.cc> Acked-by: Sam Bobroff <sbobroff@linux.ibm.com>
In order to determine a sane default cache allocation for a new CAT/CDP
resource group, all resource groups are checked to determine which cache
portions are available to share. At this time all possible CLOSIDs
that can be supported by the resource is checked. This is problematic
if the resource supports more CLOSIDs than another CAT/CDP resource. In
this case, the number of CLOSIDs that could be allocated are fewer than
the number of CLOSIDs that can be supported by the resource.
Limit the check of closids to that what is supported by the system based
on the minimum across all resources.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H Peter Anvin" <hpa@zytor.com> Cc: "Tony Luck" <tony.luck@intel.com> Cc: "Xiaochen Shen" <xiaochen.shen@intel.com> Cc: "Chen Yu" <yu.c.chen@intel.com> Link: https://lkml.kernel.org/r/1537048707-76280-10-git-send-email-fenghua.yu@intel.com
x86/intel_rdt: Fix exclusive mode handling of MBA resource
It is possible for a resource group to consist out of MBA as well as
CAT/CDP resources. The "exclusive" resource mode only applies to the
CAT/CDP resources since MBA allocations cannot be specified to overlap
or not. When a user requests a resource group to become "exclusive" then it
can only be successful if there are CAT/CDP resources in the group
and none of their CBMs associated with the group's CLOSID overlaps with
any other resource group.
Fix the "exclusive" mode setting by failing if there isn't any CAT/CDP
resource in the group and ensuring that the CBM checking is only done on
CAT/CDP resources.
A loop is used to check if a CAT resource's CBM of one CLOSID
overlaps with the CBM of another CLOSID of the same resource. The loop
is run over all CLOSIDs supported by the resource.
The problem with running the loop over all CLOSIDs supported by the
resource is that its number of supported CLOSIDs may be more than the
number of supported CLOSIDs on the system, which is the minimum number of
CLOSIDs supported across all resources.
Fix the loop to only consider the number of system supported CLOSIDs,
not all that are supported by the resource.
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
A system supporting pseudo-locking may have MBA as well as CAT
resources of which only the CAT resources could support cache
pseudo-locking. When the schemata to be pseudo-locked is provided it
should be checked that that schemata does not attempt to pseudo-lock a
MBA resource.
Fixes: e0bdfe8e3 ("x86/intel_rdt: Support creation/removal of pseudo-locked region") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H Peter Anvin" <hpa@zytor.com> Cc: "Tony Luck" <tony.luck@intel.com> Cc: "Xiaochen Shen" <xiaochen.shen@intel.com> Cc: "Chen Yu" <yu.c.chen@intel.com> Link: https://lkml.kernel.org/r/1537048707-76280-7-git-send-email-fenghua.yu@intel.com
When a new resource group is created, it is initialized with sane
defaults that currently assume the resource being initialized is a CAT
resource. This code path is also followed by a MBA resource that is not
allocated the same as a CAT resource and as a result we encounter the
following unchecked MSR access error:
unchecked MSR access error: WRMSR to 0xd51 (tried to write 0x0000 000000000064) at rIP: 0xffffffffae059994 (native_write_msr+0x4/0x20)
Call Trace:
mba_wrmsr+0x41/0x80
update_domains+0x125/0x130
rdtgroup_mkdir+0x270/0x500
Fix the above by ensuring the initial allocation is only attempted on a
CAT resource.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H Peter Anvin" <hpa@zytor.com> Cc: "Tony Luck" <tony.luck@intel.com> Cc: "Xiaochen Shen" <xiaochen.shen@intel.com> Cc: "Chen Yu" <yu.c.chen@intel.com> Link: https://lkml.kernel.org/r/1537048707-76280-6-git-send-email-fenghua.yu@intel.com
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
When multiple resources are managed by RDT, the number of CLOSIDs used
is the minimum of the CLOSIDs supported by each resource. In the function
rdt_bit_usage_show(), the annotated bitmask is created to depict how the
CAT supporting caches are being used. During this annotated bitmask
creation, each resource group is queried for its mode that is used as a
label in the annotated bitmask.
The maximum number of resource groups is currently assumed to be the
number of CLOSIDs supported by the resource for which the information is
being displayed. This is incorrect since the number of active CLOSIDs is
the minimum across all resources.
If information for a cache instance with more CLOSIDs than another is
being generated we thus encounter a warning like:
invalid mode for closid 8
WARNING: CPU: 88 PID: 1791 at [SNIP]/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
:827 rdt_bit_usage_show+0x221/0x2b0
Fix this by ensuring that only the number of supported CLOSIDs are
considered.
x86/intel_rdt: Global closid helper to support future fixes
The number of CLOSIDs supported by a system is the minimum number of
CLOSIDs supported by any of its resources. Care should be taken when
iterating over the CLOSIDs of a resource since it may be that the number
of CLOSIDs supported on the system is less than the number of CLOSIDs
supported by the resource.
Introduce a helper function that can be used to query the number of
CLOSIDs that is supported by all resources, irrespective of how many
CLOSIDs are supported by a particular resource.
Quoting Chen Yu's report: This is because for MB resource, the
r->cache.cbm_len is zero, thus calculating size in rdtgroup_cbm_to_size()
will trigger the exception.
Fix this issue in the 'size' file by getting correct memory bandwidth value
which is in MBps when MBA software controller is enabled or in percentage
when MBA software controller is disabled.
Each resource is associated with a parsing callback to parse the data
provided from user space when writing schemata file.
The 'data' parameter in the callbacks is defined as a void pointer which
is error prone due to lack of type check.
parse_bw() processes the 'data' parameter as a string while its caller
actually passes the parameter as a pointer to struct rdt_cbm_parse_data.
Thus, parse_bw() takes wrong data and causes failure of parsing MBA
throttle value.
To fix the issue, the 'data' parameter in all parsing callbacks is defined
and handled as a pointer to struct rdt_parse_data (renamed from struct
rdt_cbm_parse_data).
Fixes: 7604df6e16ae ("x86/intel_rdt: Support flexible data to parsing callbacks") Fixes: 9ab9aa15c309 ("x86/intel_rdt: Ensure requested schemata respects mode") Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H Peter Anvin" <hpa@zytor.com> Cc: "Tony Luck" <tony.luck@intel.com> Cc: "Chen Yu" <yu.c.chen@intel.com> Link: https://lkml.kernel.org/r/1537048707-76280-2-git-send-email-fenghua.yu@intel.com
intel_th: Fix resource handling for ACPI glue layer
The core of the driver expects the resource array from the glue layer
to be indexed by even numbers, as is the case for 64-bit PCI resources.
This doesn't hold true for others, ACPI in this instance, which leads
to an out-of-bounds access and an ioremap() on whatever address that
access fetches.
This patch fixes the problem by reading resource array differently based
on whether the 64-bit flag is set, which would indicate PCI glue layer.
Commit a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
brings in new subdevice addition/removal logic that's broken for "host
mode": the SWITCH device has no children to begin with, which is not
handled in the code. This results in a null dereference bug later down
the path.
This patch fixes the subdevice removal code to handle host mode correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices") CC: stable@vger.kernel.org # v4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing vsa.console before using it to index vc_cons
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
projects / linux.git / log