Tin Huynh [Thu, 10 Nov 2016 02:56:33 +0000 (09:56 +0700)]
i2c: designware: Implement support for SMBus block read and write
Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Signed-off-by: Tin Huynh <tnhuynh@apm.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Julia Lawall [Sat, 15 Oct 2016 17:32:01 +0000 (19:32 +0200)]
i2c: constify i2c_adapter_quirks structures
Check for i2c_adapter_quirks structures that are only stored in the
quirks field of an i2c_adapter structure. This field is declared
const, so i2c_adapter_quirks structures that have this property can be
declared as const also.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ray Jui <ray.jui@broadcom.com> # for bcm-iproc Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Vadim Pasternak [Thu, 10 Nov 2016 21:26:23 +0000 (21:26 +0000)]
i2c: mux: mellanox: add driver
This driver allows I2C routing controlled through CPLD select registers on
a wide range of Mellanox systems (CPLD Lattice device).
MUX selection is provided by digital and analog HW. Analog part is not
under SW control.
Digital part is under CPLD control (channel selection/de-selection).
Connectivity schema.
.---. .-------------.
| l | | |-- i2cx1 -- i2cx8
| i |-- i2cn --+--| mlxcpld mux |
| n | | | |-- i2cy1 -- i2cy8
| u | | '-------------'
| x | | |
'---' '---------'
i2c-mux-mlxpcld does not necessarily require i2c-mlxcpld. It can be used
along with another bus driver, and still control i2c routing through CPLD
mux selection, in case the system is equipped with CPLD capable of mux
selection control.
The Kconfig currently controlling compilation of this code is:
drivers/i2c/muxes/Kconfig:config I2C_MUX_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com> Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:44 +0000 (12:47 +0000)]
mfd: 88pm860x: Move over to new I2C device .probe() call
As part of an effort to rid the mostly unused second parameter for I2C
related .probe() functions and to conform to other existing frameworks
we're moving over to a temporary replacement .probe() call-back.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:41 +0000 (12:47 +0000)]
i2c: Provide a temporary .probe_new() call-back type
This will aid the seamless removal of the current probe()'s, more
commonly unused than used second parameter. Most I2C drivers can
simply switch over to the new interface, others which have DT
support can use its own matching instead and others can call
i2c_match_id() themselves. This brings I2C's device probe method
into line with other similar interfaces in the kernel and prevents
the requirement to pass an i2c_device_id table.
Suggested-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: fix rebase conflicts and adapt for dev_pm_domain_{attach,detach}] Tested-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:40 +0000 (12:47 +0000)]
i2c: Export i2c_match_id() for direct use by device drivers
When there was no other way to match a I2C device to driver i2c_match_id()
was exclusively used. However, now there are other types of tables which
are commonly supplied, matching on an i2c_device_id table is used less
frequently. Instead of _always_ calling i2c_match_id() from within the
framework, we only need to do so from drivers which have no other way of
matching. This patch makes i2c_match_id() available to the aforementioned
device drivers.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Tested-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:39 +0000 (12:47 +0000)]
i2c: Make I2C ID tables non-mandatory for DT'ed devices
Currently the I2C framework insists on devices supplying an I2C ID
table. Many of the devices which do so unnecessarily adding quite a
few wasted lines to kernel code. This patch allows drivers a means
to 'not' supply the aforementioned table and match on DT match tables
instead.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Tested-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:38 +0000 (12:47 +0000)]
i2c: Match using traditional OF methods, then by vendor-less compatible strings
This function provides a single call for all I2C devices which need to
match firstly using traditional OF means i.e by of_node, then if that
fails we attempt to match using the supplied I2C client name with a
list of supplied compatible strings with the '<vendor>,' string
removed. The latter is required due to the unruly naming conventions
used currently by I2C devices.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: Fix static inline usage on !CONFIG_OF] Tested-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:37 +0000 (12:47 +0000)]
i2c: Add the ability to match device to compatible string without an of_node
A great deal of I2C devices are currently matched via DT node name, and
as such the compatible naming convention of '<vendor>,<device>' has gone
somewhat awry - some nodes don't supply one, some supply an arbitrary
string and others the correct device name with an arbitrary vendor prefix.
In an effort to correct this problem we have to supply a mechanism to
match a device by compatible string AND by simple device name. This
function strips off the '<vendor>,' part of a supplied compatible string
and attempts to match without it.
It is also used for sysfs, where a user can choose to instantiate a
device on an i2c bus using the sysfs interface by providing a string and
address to match and communicate with the device on the bus. Presently
this string is only matched against the old i2c device id style strings,
even in the presence of full device tree compatible strings with vendor
prefixes.
Providing a vendor-prefixed string to the sysfs interface will not match
against the device tree of_match_device() calls as there is no device
tree node to parse from the sysfs interface.
This function can match both vendor prefixed and stripped compatible
strings on the sysfs interface.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Mon, 7 Nov 2016 12:47:36 +0000 (12:47 +0000)]
i2c: Add pointer dereference protection to i2c_match_id()
Here we're providing dereference protection for i2c_match_id(), which
saves us having to do it each time it's called. We're also stripping
out the (now) needless checks in i2c_device_match(). This patch paves
the way for other, similar code trimming.
Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Tested-by: Kieran Bingham <kieran@bingham.xyz> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:12 +0000 (22:06 +0200)]
i2c: bcm2835: Add support for Repeated Start Condition
Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.
This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
of using polling. There is no interrupt for Transfer Active, but by
not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
CLEAR to the control register instead of just zero.
Using just zero gave many errors. This might be the reason why
downstream had to disable this feature and make it available with a
module parameter.
I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:11 +0000 (22:06 +0200)]
i2c: bcm2835: Can't support I2C_M_IGNORE_NAK
The controller can't support this flag, so remove it.
Documentation/i2c/i2c-protocol states that all of the message is sent:
I2C_M_IGNORE_NAK:
Normally message is interrupted immediately if there is [NA] from the
client. Setting this flag treats any [NA] as [A], and all of
message is sent.
>From the BCM2835 ARM Peripherals datasheet:
The ERR field is set when the slave fails to acknowledge either
its address or a data byte written to it.
So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:10 +0000 (22:06 +0200)]
i2c: bcm2835: Use dev_dbg logging on transfer errors
Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:09 +0000 (22:06 +0200)]
i2c: bcm2835: Protect against unexpected TXW/RXR interrupts
If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.
(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.
Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.
Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Noralf Trønnes [Mon, 3 Oct 2016 20:06:08 +0000 (22:06 +0200)]
i2c: bcm2835: Fix hang for writing messages larger than 16 bytes
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.
The BCM2835 ARM Peripherals datasheet has this to say about the flags:
TXD: is set when the FIFO has space for at least one byte of data.
RXD: is set when the FIFO contains at least one byte of data.
TXW: is set during a write transfer and the FIFO is less than full.
RXR: is set during a read transfer and the FIFO is or more full.
Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sat, 5 Nov 2016 18:46:02 +0000 (11:46 -0700)]
Merge branches 'sched-urgent-for-linus' and 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull stack vmap fixups from Thomas Gleixner:
"Two small patches related to sched_show_task():
- make sure to hold a reference on the task stack while accessing it
- remove the thread_saved_pc printout
.. and add a sanity check into release_task_stack() to catch problems
with task stack references"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Remove pointless printout in sched_show_task()
sched/core: Fix oops in sched_show_task()
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fork: Add task stack refcounting sanity check and prevent premature task stack freeing
Linus Torvalds [Sat, 5 Nov 2016 18:34:07 +0000 (11:34 -0700)]
Merge tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"There are several bug fixes queued:
- fix raid5-cache recovery bugs
- fix discard IO error handling for raid1/10
- fix array sync writes bogus position to superblock
- fix IO error handling for raid array with external metadata"
* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: be careful not lot leak internal curr_resync value into metadata. -- (all)
raid1: handle read error also in readonly mode
raid5-cache: correct condition for empty metadata write
md: report 'write_pending' state when array in sync
md/raid5: write an empty meta-block when creating log super-block
md/raid5: initialize next_checkpoint field before use
RAID10: ignore discard error
RAID1: ignore discard error
Linus Torvalds [Sat, 5 Nov 2016 18:28:21 +0000 (11:28 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
Linus Torvalds [Sat, 5 Nov 2016 18:15:09 +0000 (11:15 -0700)]
Merge tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
Linus Torvalds [Sat, 5 Nov 2016 18:11:31 +0000 (11:11 -0700)]
Merge tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix for a Qualcomm driver issue that causes a use-before-set crash
- fix for DesignWare iATU unroll support that causes external aborts
when enabling the host bridge
* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
Linus Torvalds [Sat, 5 Nov 2016 17:52:29 +0000 (10:52 -0700)]
Merge tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates to reflect some new maintainers/submaintainers.
We have some great volunteers who've been developing and reviewing
already. We're going to try a group maintainership model, so
eventually you'll probably see pull requests from people besides me.
- NAND fixes from Boris:
"Three simple fixes:
- fix a non-critical bug in the gpmi driver
- fix a bug in the 'automatic NAND timings selection' feature
introduced in 4.9-rc1
- fix a false positive uninitialized-var warning"
* tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd:
mtd: mtk: avoid warning in mtk_ecc_encode
mtd: nand: Fix data interface configuration logic
mtd: nand: gpmi: disable the clocks on errors
MAINTAINERS: add more people to the MTD maintainer team
MAINTAINERS: add a maintainer for the SPI NOR subsystem
Linus Torvalds [Sat, 5 Nov 2016 17:42:20 +0000 (10:42 -0700)]
Merge tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.9 series:
- Fix a nasty file descriptor leak when getting line handles.
- A fix for a cleanup that seemed innocent but created a problem for
drivers instantiating several gpiochips for one single OF node.
- Fix a unpredictable problem using irq_domain_simple() in the mvebu
driver by converting it to a lineas irqdomain"
* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/mvebu: Use irq_domain_add_linear
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak
Linus Torvalds [Sat, 5 Nov 2016 03:12:10 +0000 (20:12 -0700)]
Merge tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fixes for some recent regressions including fallout from the vmalloc'd
stack change (after which we can no longer encrypt stuff on the
stack)"
* tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix general protection fault in release_lock_stateid()
svcrdma: backchannel cannot share a page for send and rcv buffers
sunrpc: fix some missing rq_rbuffer assignments
sunrpc: don't pass on-stack memory to sg_set_buf
nfsd: move blocked lock handling under a dedicated spinlock
Linus Torvalds [Sat, 5 Nov 2016 03:08:16 +0000 (20:08 -0700)]
Merge branch 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from Chris Mason:
"Some fixes that Dave Sterba collected. We held off on these last week
because I was focused on the memory corruption testing"
* 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix WARNING in btrfs_select_ref_head()
Btrfs: remove some no-op casts
btrfs: pass correct args to btrfs_async_run_delayed_refs()
btrfs: make file clone aware of fatal signals
btrfs: qgroup: Prevent qgroup->reserved from going subzero
Btrfs: kill BUG_ON in do_relocation
Linus Torvalds [Sat, 5 Nov 2016 03:03:14 +0000 (20:03 -0700)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix two more POSIX ACL bugs introduced in 4.8 and add a missing fsync
during copy up to prevent possible data loss"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fsync after copy-up
ovl: fix get_acl() on tmpfs
ovl: update S_ISGID when setting posix ACLs
Linus Torvalds [Fri, 4 Nov 2016 20:30:13 +0000 (13:30 -0700)]
Merge tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for amdgpu, radeon, intel, imx and virtio-gpu.
This is a bit larger than I'd like, but I had some stuff I meant to
send for -rc3 but was waiting for the PAT regression fix to land. So
this is really fixes for rc3 and rc4 in one go.
There are a set of fixes for an oops we've been seeing around MST
display unplug, along with more suspend/resume and shutdown fixes for
amdgpu, one power management follow on fix for nouveau, and set of imx
fixes, and a single virtio-gpu regression fix"
* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
virtio-gpu: fix vblank events
drm/nouveau/acpi: fix check for power resources support
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
drm/amdgpu/si_dpm: workaround for SI kickers
drm/radeon/si_dpm: workaround for SI kickers
drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
...
Niklas Cassel [Fri, 14 Oct 2016 21:54:55 +0000 (23:54 +0200)]
PCI: designware: Check for iATU unroll support after initializing host
dw_pcie_iatu_unroll_enabled() reads a dbi_base register. Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init. Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.
Fixes: a0601a470537 ("PCI: designware: Add iATU Unroll feature") Tested-by: James Le Cuirot <chewi@gentoo.org> Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Joao Pinto <jpinto@synopsys.com> Acked-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 4 Nov 2016 20:08:05 +0000 (13:08 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One NULL pointer dereference, and two fixes for regressions introduced
during the merge window.
The rest are fixes for MIPS, s390 and nested VMX"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: Check memopp before dereference (CVE-2016-8630)
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
KVM: x86: fix wbinvd_dirty_mask use-after-free
kvm/x86: Show WRMSR data is in hex
kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
KVM: document lock orders
KVM: fix OOPS on flush_work
KVM: s390: Fix STHYI buffer alignment for diag224
KVM: MIPS: Precalculate MMIO load resume PC
KVM: MIPS: Make ERET handle ERL before EXL
KVM: MIPS: Fix lazy user ASID regenerate for SMP
Linus Torvalds [Fri, 4 Nov 2016 20:03:57 +0000 (13:03 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A set of MIPS fixes for 4.9:
- lots of fixes for printk continuations
- six fixes for FP related code.
- fix max_low_pfn with disabled highmem
- fix KASLR handling of NULL FDT and KASLR for generic kernels
- fix build of compressed image
- provide default mips_cpc_default_phys_base to ignore CPC
- fix reboot on Malta"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix max_low_pfn with disabled highmem
MIPS: Correct MIPS I FP sigcontext layout
MIPS: Fix ISA I/II FP signal context offsets
MIPS: Remove FIR from ISA I FP signal context
MIPS: Fix ISA I FP sigcontext access violation handling
MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
MIPS: dump_tlb: Fix printk continuations
MIPS: Fix __show_regs() output
MIPS: traps: Fix output of show_code
MIPS: traps: Fix output of show_stacktrace
MIPS: traps: Fix output of show_backtrace
MIPS: Fix build of compressed image
MIPS: generic: Fix KASLR for generic kernel.
MIPS: KASLR: Fix handling of NULL FDT
MIPS: Malta: Fixup reboot
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Linus Torvalds [Fri, 4 Nov 2016 20:01:13 +0000 (13:01 -0700)]
Merge branch 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The first three patches are trivial and add some required KERN_CONT,
ignore the new pkey syscalls on parisc and use the LINUX_GATEWAY_ADDR
define instead of hardcoded values.
The two patches from Dave Anglin are important.
The first one avoids trashing the sr2 and sr3 space registers in the
Light-weight syscall path. Especially the usage of sr3 is critical
since it may get trashed by the interrupt handler.
The second patch is even more important and tagged for stable series.
It protects one critical section in the syscall entry path by
disabling local interrupts. Without disabling interrupts, the sr7
space register may not be in sync with the current stack setup and
thus an incoming hardware interrupt may destroy memory in random
userspace areas"
* 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Ignore the pkey system calls for now
parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
parisc: Ensure consistent state when switching to kernel stack at syscall entry
parisc: Avoid trashing sr2 and sr3 in LWS code
parisc: use KERN_CONT when printing device inventory
i2c: core: fix NULL pointer dereference under race condition
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
James Hogan [Tue, 1 Nov 2016 13:59:09 +0000 (13:59 +0000)]
MIPS: Fix max_low_pfn with disabled highmem
When low memory doesn't reach HIGHMEM_START (e.g. up to 256MB at PA=0 is
common) and highmem is present above HIGHMEM_START (e.g. on Malta the
RAM overlayed by the IO region is aliased at PA=0x90000000), max_low_pfn
will be initially calculated very large and then clipped down to
HIGHMEM_START.
This causes crashes when reading /sys/kernel/mm/page_idle/bitmap
(i.e. CONFIG_IDLE_PAGE_TRACKING=y) when highmem is disabled. pfn_valid()
will compare against max_mapnr which is derived from max_low_pfn when
there is no highend_pfn set up, and will return true for PFNs right up
to HIGHMEM_START, even though they are beyond the end of low memory and
no page structs will actually exist for these PFNs.
This is fixed by skipping high memory regions when initially calculating
max_low_pfn if highmem is disabled, so it doesn't get clipped too high.
We also clip regions which overlap the highmem boundary when highmem is
disabled, so that max_pfn doesn't extend into highmem either.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14490/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit 80cbfad79096 ("MIPS: Correct MIPS I FP context
layout") and correct the way Floating Point General registers are stored
in a signal context with MIPS I hardware.
Use the S.D and L.D assembly macros to have pairs of SWC1 instructions
and pairs of LWC1 instructions produced, respectively, in an arrangement
which makes the memory representation of floating-point data passed
compatible with that used by hardware SDC1 and LDC1 instructions, where
available, regardless of the hardware endianness used. This matches the
layout used by r4k_fpu.S, ensuring run-time compatibility for MIPS I
software across all o32 hardware platforms.
Define an EX2 macro to handle exceptions from both hardware instructions
implicitly produced from S.D and L.D assembly macros.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14477/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a regression introduced with commit 2db9ca0a3551 ("MIPS: Use struct
mips_abi offsets to save FP context") for MIPS I/I FP signal contexts,
by converting save/restore code to the updated internal API. Start FGR
offsets from 0 rather than SC_FPREGS from $a0 and use $a1 rather than
the offset of SC_FPC_CSR from $a0 for the Floating Point Control/Status
Register (FCSR).
Document the new internal API and adjust assembly code formatting for
consistency.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14476/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit e50c0a8fa60d ("Support the MIPS32 / MIPS64 DSP ASE.")
and remove the Floating Point Implementation Register (FIR) from the FP
register set recorded in a signal context with MIPS I processors too, in
line with the change applied to r4k_fpu.S.
The `sc_fpc_eir' slot is unused according to our current ABI and the FIR
register is read-only and always directly accessible from user software.
[ralf@linux-mips.org: This is also required because the next commit depends
on it.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14475/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: Fix ISA I FP sigcontext access violation handling
Complement commit 0ae8dceaebe3 ("Merge with 2.3.10.") and use the local
`fault' handler to recover from FP sigcontext access violation faults,
like corresponding code does in r4k_fpu.S. The `bad_stack' handler is
in syscall.c and is not suitable here as we want to propagate the error
condition up through the caller rather than killing the thread outright.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14474/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* commit 443c44032a54 ("MIPS: Always clear FCSR cause bits after
emulation"),
* commit 64bedffe4968 ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),
* commit b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause
bits"),
* commit b54d2901517d ("Properly handle branch delay slots in connection
with signals.").
Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume. Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits. Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed. Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
Complement commit ac9ad83bc318 ("MIPS: prevent FP context set via ptrace
being discarded") and also initialize the FP context whenever FCSR alone
is written with a PTRACE_POKEUSR request addressing FPC_CSR, rather than
along with the full FPU register set in the case of the PTRACE_SETFPREGS
request.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14459/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 21 Oct 2016 19:06:40 +0000 (20:06 +0100)]
MIPS: dump_tlb: Fix printk continuations
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from TLB dumps on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Continuation is also used for the second line of each TLB entry printed
in dump_tlb.c even though it has a newline, since it is a continuation
of the interpretation of the same TLB entry. For example:
Paul Burton [Wed, 19 Oct 2016 13:33:23 +0000 (14:33 +0100)]
MIPS: Fix __show_regs() output
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from __show_regs() on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected register output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14432/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:22 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_code
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_code on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14431/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:21 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_stacktrace
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_stacktrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output. Also
start a new line with printk such that the presence of timing
information does not interfere with output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14430/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:20 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_backtrace
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_backtrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14429/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 17 Oct 2016 09:09:39 +0000 (10:09 +0100)]
MIPS: Fix build of compressed image
Changes introduced to arch/mips/Makefile for the generic kernel resulted
in build errors when making a compressed image if platform-y has multiple
values, like this:
make[2]: *** No rule to make target `alchemy/'.
make[1]: *** [vmlinuz] Error 2
make[1]: Target `_all' not remade because of errors.
make: *** [sub-make] Error 2
make: Target `_all' not remade because of errors.
Fix this by quoting $(platform-y) as it is passed to the Makefile in
arch/mips/boot/compressed/Makefile
Matt Redfearn [Mon, 17 Oct 2016 16:25:24 +0000 (17:25 +0100)]
MIPS: generic: Fix KASLR for generic kernel.
The KASLR code requires that the plat_get_fdt() function return the
address of the device tree, and it must be available early in the boot,
before prom_init() is called. Move the code determining the address of
the device tree into plat_get_fdt, and call that from prom_init().
The fdt pointer will be set up by plat_get_fdt() called from
relocate_kernel initially and once the relocated kernel has started,
prom_init() will use it again to determine the address in the relocated
image.
Matt Redfearn [Mon, 17 Oct 2016 16:21:46 +0000 (17:21 +0100)]
MIPS: KASLR: Fix handling of NULL FDT
If platform code returns a NULL pointer to the FDT, initial_boot_params
will not get set to a valid pointer and attempting to find the /chosen
node in it will cause a NULL pointer dereference and the kernel to crash
immediately on startup - with no output to the console.
Fix this by checking that initial_boot_params is valid before using it.
Paul Burton [Fri, 14 Oct 2016 09:17:32 +0000 (10:17 +0100)]
MIPS: Malta: Fixup reboot
Commit 10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot")
converted the Malta board to use the generic syscon-reboot driver to
handle reboots, but incorrectly used the value 0x4d rather than 0x42 as
the magic to write to the reboot register.
I also incorrectly believed that syscon/regmap would default to native
endianness, but this isn't the case. Force this by specifying with a
native-endian property in the devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot") Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14396/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Sat, 15 Oct 2016 22:03:43 +0000 (23:03 +0100)]
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Provide a default implementation of mips_cpc_default_phys_base() which
simply returns 0, and adjust mips_cpc_phys_base() to allow for
mips_cpc_default_phys_base() returning 0. This allows kernels which
include CPC support to be built without platform code & simply ignore
the CPC if it wasn't already enabled by the bootloader.
This fixes link failures such as the following from generic defconfigs:
arch/mips/built-in.o: In function `mips_cpc_phys_base':
arch/mips/kernel/mips-cpc.c:47: undefined reference to `mips_cpc_default_phys_base'
[ralf@linux-mips.org: changed prototype for coding style compliance.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14401/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Cc: stable@vger.kernel.org Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 29 Oct 2016 19:28:18 +0000 (21:28 +0200)]
firewire: net: guard against rx buffer overflows
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
Linus Torvalds [Tue, 1 Nov 2016 23:47:18 +0000 (17:47 -0600)]
sched/core: Remove pointless printout in sched_show_task()
In sched_show_task() we print out a useless hex number, not even a
symbol, and there's a big question mark whether this even makes sense
anyway, I suspect we should just remove it all.
Tetsuo Handa [Wed, 2 Nov 2016 10:50:29 +0000 (19:50 +0900)]
sched/core: Fix oops in sched_show_task()
When CONFIG_THREAD_INFO_IN_TASK=y, it is possible that an exited thread
remains in the task list after its stack pointer was already set to NULL.
Therefore, thread_saved_pc() and stack_not_used() in sched_show_task()
will trigger NULL pointer dereference if an attempt to dump such thread's
traces (e.g. SysRq-t, khungtaskd) is made.
Since show_stack() in sched_show_task() calls try_get_task_stack() and
sched_show_task() is called from interrupt context, calling
try_get_task_stack() from sched_show_task() will be safe as well.
Dave Airlie [Thu, 3 Nov 2016 00:18:20 +0000 (10:18 +1000)]
Merge tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel into drm-fixes
batch of scattered i915 fixes.
* tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
Dave Airlie [Thu, 3 Nov 2016 00:17:50 +0000 (10:17 +1000)]
Merge tag 'imx-drm-fixes-20161021' of git://git.pengutronix.de/pza/linux into drm-fixes
imx-drm plane, build warning, and error handling fixes
- some fixes for active plane reconfiguration support
- hide unused label in case of disabled CONFIG_DRM_FBDEV_EMULATION,
which caused a build warning
- fixed error handling in imx_drm_bind
- disallow odd x/y plane offsets for chroma subsampled formats
- disable local alpha when switching from a format with alpha
channel to an opaque format
* tag 'imx-drm-fixes-20161021' of git://git.pengutronix.de/pza/linux:
drm/imx: ipuv3-plane: disable local alpha for planes without alpha channel
drm/imx: ipuv3-plane: make sure x/y offsets are even in case of chroma subsampling
drm/imx: ipuv3-plane: Access old u/vbo properly in ->atomic_check for YU12/YV12
drm/imx: drm_dev_alloc() returns error pointers
drm/imx: ipuv3-plane: Skip setting u/vbo only when we don't need modeset
drm/imx: ipuv3-plane: Switch EBA buffer only when we don't need modeset
gpu: ipu-v3: Use ERR_CAST instead of ERR_PTR(PTR_ERR())
drm/imx: hide an unused label
Gerd Hoffmann [Tue, 18 Oct 2016 17:32:30 +0000 (15:32 -0200)]
virtio-gpu: fix vblank events
virtio-gpu sends vblank events in virtio_gpu_crtc_atomic_flush, and
because of that it must be called for disabled planes too. Ask
drm_atomic_helper_commit_planes to do that.
v2: update to use new drm_atomic_helper_commit_planes() API.
parisc: Ensure consistent state when switching to kernel stack at syscall entry
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Cc: <stable@vger.kernel.org> Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
There is no need to trash sr2 and sr3 in the Light-weight syscall (LWS). sr2
already points to kernel space (it's zero in userspace, otherwise syscalls
wouldn't work), and since the LWS code is executed in userspace, we can simply
ignore to preload sr3.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
Owen Hofmann [Thu, 27 Oct 2016 18:25:52 +0000 (11:25 -0700)]
kvm: x86: Check memopp before dereference (CVE-2016-8630)
Commit 41061cdb98 ("KVM: emulate: do not initialize memopp") removes a
check for non-NULL under incorrect assumptions. An undefined instruction
with a ModR/M byte with Mod=0 and R/M-5 (e.g. 0xc7 0x15) will attempt
to dereference a null pointer here.
Jim Mattson [Fri, 28 Oct 2016 15:29:39 +0000 (08:29 -0700)]
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
After a successful VM-entry with the "VMCS shadowing" VM-execution
control set, the shadow VMCS referenced by the VMCS link pointer field
in the current VMCS becomes active on the logical processor.
A VMCS that is made active on more than one logical processor may become
corrupted. Therefore, before an active VMCS can be migrated to another
logical processor, the first logical processor must execute a VMCLEAR
for the active VMCS. VMCLEAR both ensures that all VMCS data are written
to memory and makes the VMCS inactive.
Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-By: David Matlack <dmatlack@google.com>
Message-Id: <1477668579-22555-1-git-send-email-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 31 Oct 2016 23:39:48 +0000 (00:39 +0100)]
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
Since commit a545ab6a0085 ("kvm: x86: add tsc_offset field to struct
kvm_vcpu_arch", 2016-09-07) the offset between host and L1 TSC is
cached and need not be fished out of the VMCS or VMCB. This means
that we can implement adjust_tsc_offset_guest and read_l1_tsc
entirely in generic code. The simplification is particularly
significant for VMX code, where vmx->nested.vmcs01_tsc_offset
was duplicating what is now in vcpu->arch.tsc_offset. Therefore
the vmcs01_tsc_offset can be dropped completely.
More importantly, this fixes KVM_GET_CLOCK/KVM_SET_CLOCK
which, after commit 108b249c453d ("KVM: x86: introduce get_kvmclock_ns",
2016-09-01) called read_l1_tsc while the VMCS was not loaded.
It thus returned bogus values on Intel CPUs.
Fixes: 108b249c453dd7132599ab6dc7e435a7036c193f Reported-by: Roman Kagan <rkagan@virtuozzo.com> Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Tue, 1 Nov 2016 23:48:46 +0000 (17:48 -0600)]
Merge tag 'gcc-plugins-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin fixes from Kees Cook:
- make sure required exports from gcc plugins are visible to gcc
- switch latent_entropy to unsigned long to avoid stack frame bloat
* tag 'gcc-plugins-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Fix wrong gcc code generation with 64 bit variables
gcc-plugins: Export symbols needed by gcc
Linus Torvalds [Tue, 1 Nov 2016 22:56:05 +0000 (16:56 -0600)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Tests, fixes and cleanups.
Just minor tweaks, there's nothing major in this cycle"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: mark vring_dma_dev inline
virtio/vhost: add Jason to list of maintainers
virtio_blk: Delete an unnecessary initialisation in init_vq()
virtio_blk: Use kmalloc_array() in init_vq()
virtio: remove config.c
virtio: console: Unlock vqs while freeing buffers
ringtest: poll for new buffers once before updating event index
ringtest: commonize implementation of poll_avail/poll_used
ringtest: use link-time optimization
virtio: update balloon size in balloon "probe"
virtio_ring: Make interrupt suppression spec compliant
virtio_pci: Limit DMA mask to 44 bits for legacy virtio devices
Jeff Layton says:
> Hm...now that I look though, this is a little suspicious:
>
> struct nfs4_openowner *oo = openowner(stp->st_openstp->st_stateowner);
>
> I wonder if it's possible for the openstateid to have already been
> destroyed at this point.
>
> We might be better off doing something like this to get the client pointer:
>
> stp->st_stid.sc_client;
>
> ...which should be more direct and less dependent on other stateids
> staying valid.
With the suggested change, I am no longer able to reproduce the above oops.
v2: Fix unhash_lock_stateid() as well
Fix-suggested-by: Jeff Layton <jlayton@redhat.com> Fixes: 42691398be08 ('nfsd: Fix race between FREE_STATEID and LOCK') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Chuck Lever [Sat, 29 Oct 2016 02:22:33 +0000 (22:22 -0400)]
svcrdma: backchannel cannot share a page for send and rcv buffers
The underlying transport releases the page pointed to by rq_buffer
during xprt_rdma_bc_send_request. When the backchannel reply arrives,
rq_rbuffer then points to freed memory.
Fixes: 68778945e46f ('SUNRPC: Separate buffer pointers for RPC ...') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Jason Gunthorpe [Wed, 19 Oct 2016 21:03:41 +0000 (15:03 -0600)]
gpio/mvebu: Use irq_domain_add_linear
This fixes the irq allocation in this driver to not print:
irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.
Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy
Fixes: ce931f571b6d ("gpio/mvebu: convert to use irq_domain_add_simple()") Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If something goes wrong with task stack refcounting and a stack
refcount hits zero too early, warn and leak it rather than
potentially freeing it early (and silently).
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/f29119c783a9680a4b4656e751b6123917ace94b.1477926663.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Wu [Mon, 31 Oct 2016 22:48:22 +0000 (23:48 +0100)]
drm/nouveau/acpi: fix check for power resources support
Check whether the kernel really supports power resources for a device,
otherwise the power might not be removed when the device is runtime
suspended (DSM should still work in these cases where PR does not).
This is a workaround for a problem where ACPICA and Windows 10 differ in
behavior. ACPICA does not correctly enumerate power resources within a
conditional block (due to delayed execution of such blocks) and as a
result power_resources is set to false even if _PR3 exists.
Fixes: 692a17dcc292 ("drm/nouveau/acpi: fix lockup with PCIe runtime PM") Link: https://bugs.freedesktop.org/show_bug.cgi?id=98398 Reported-and-tested-by: Rick Kerkhof <rick.2889@gmail.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Dave Airlie <airlied@redhat.com>
Masahiro Yamada [Tue, 25 Oct 2016 01:47:44 +0000 (10:47 +0900)]
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
Sylvain Lemieux reports the LPC32xx GPIO driver is broken since
commit 762c2e46c059 ("gpio: of: remove of_gpiochip_and_xlate() and
struct gg_data"). Probably, gpio-etraxfs.c and gpio-davinci.c are
broken too.
Those drivers register multiple gpio_chip that are associated to a
single OF node, and their own .of_xlate() checks if the passed
gpio_chip is valid.
Now, the problem is of_find_gpiochip_by_node() returns the first
gpio_chip found to match the given node. So, .of_xlate() fails,
except for the first GPIO bank.
Reverting the commit could be a solution, but I do not want to go
back to the mess of struct gg_data. Another solution here is to
take the match by a node pointer and the success of .of_xlate().
It is a bit clumsy to call .of_xlate twice; for gpio_chip matching
and for really getting the gpio_desc index. Perhaps, our long-term
goal might be to convert the drivers to single chip registration,
but this commit will solve the problem until then.
When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.
But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.
anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.
Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.
Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.
Linus Torvalds [Mon, 31 Oct 2016 18:54:11 +0000 (11:54 -0700)]
Merge tag 'spi-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown: "A few small fixes for SPI, one core fix
that only applies in cases where we're handling DT overlays and a
couple of driver specific fixes:
- Fix handling of error cases when instantiating DT overlays so we
don't end up just ignoring devices that encountered an error during
instantiation.
- Avoid reading uninitialized data when handing spurious interrupts
in the espi driver.
- A driver specific fix for the dspi driver to fix a bad interaction
with u-boot"
* tag 'spi-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dspi: clear SPI_SR before enable interrupt
spi: fsl-espi: avoid processing uninitalized data on error
spi: mark device nodes only in case of successful instantiation
Kees Cook [Tue, 18 Oct 2016 22:08:04 +0000 (00:08 +0200)]
latent_entropy: Fix wrong gcc code generation with 64 bit variables
The stack frame size could grow too large when the plugin used long long
on 32-bit architectures when the given function had too many basic blocks.
The gcc warning was:
drivers/pci/hotplug/ibmphp_ebda.c: In function 'ibmphp_access_ebda':
drivers/pci/hotplug/ibmphp_ebda.c:409:1: warning: the frame size of 1108 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This switches latent_entropy from u64 to unsigned long.
Linus Torvalds [Mon, 31 Oct 2016 17:14:09 +0000 (10:14 -0700)]
Merge tag 'regulator-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Fix ramp_delay warnings for v4.9
A new warning was introduced for missing information about the time
that regulators take to power on in v4.9. This is in theory a real
issue but for most practical regulators the communication overhead of
talking to the device is greater than the ramp time so a lot of
drivers don't set it and the warning is far too noisy without
identifying practical issues.
Just remove the warning for now"
* tag 'regulator-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: silence warning: "VDD1: ramp_delay not set"
Linus Torvalds [Mon, 31 Oct 2016 17:12:35 +0000 (10:12 -0700)]
Merge tag 'regmap-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of small build fixes here, nothing major.
The missing include is triggered in some configurations and the
renaming of ret is defensive for the benefit of some drivers people
are in the process of mainlining"
* tag 'regmap-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Rename ret variable in regmap_read_poll_timeout
regmap: include <linux/delay.h> from include/linux/regmap.h
Jarkko Sakkinen [Tue, 4 Oct 2016 06:49:47 +0000 (09:49 +0300)]
tpm: remove invalid min length check from tpm_do_selftest()
Removal of this check was not properly amended to the original commit.
Cc: stable@vger.kernel.org Fixes: 0c541332231e ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull sparc fixes from David Miller:
"Several sparc64 bug fixes here:
1) Make the user copy routines on sparc64 return a properly accurate
residual length when an exception occurs.
2) We can get enormous kernel TLB range flush requests from vmalloc
unmaps, so handle these more gracefully by doing full flushes
instead of going page-by-page.
3) Cope properly with negative branch offsets in sparc jump-label
support, from James Clarke.
4) Some old-style decl GCC warning fixups from Tobias Klauser"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Handle extremely large kernel TLB range flushes more gracefully.
sparc64: Fix illegal relative branches in hypervisor patched TLB cross-call code.
sparc64: Fix instruction count in comment for __hypervisor_flush_tlb_pending.
sparc64: Handle extremely large kernel TSB range flushes sanely.
sparc: Handle negative offsets in arch_jump_label_transform
sparc64: Fix illegal relative branches in hypervisor patched TLB code.
sparc64: Delete now unused user copy fixup functions.
sparc64: Delete now unused user copy assembler helpers.
sparc64: Convert U3copy_{from,to}_user to accurate exception reporting.
sparc64: Convert NG2copy_{from,to}_user to accurate exception reporting.
sparc64: Convert NGcopy_{from,to}_user to accurate exception reporting.
sparc64: Convert NG4copy_{from,to}_user to accurate exception reporting.
sparc64: Convert U1copy_{from,to}_user to accurate exception reporting.
sparc64: Convert GENcopy_{from,to}_user to accurate exception reporting.
sparc64: Convert copy_in_user to accurate exception reporting.
sparc64: Prepare to move to more saner user copy exception handling.
sparc64: Delete __ret_efault.
sparc32: Fix old style declaration GCC warnings
sparc64: Fix old style declaration GCC warnings
sparc64: Setup a scheduling domain for highest level cache.
Miklos Szeredi [Mon, 31 Oct 2016 13:42:14 +0000 (14:42 +0100)]
ovl: fsync after copy-up
Make sure the copied up file hits the disk before renaming to the final
destination. If this is not done then the copy-up may corrupt the data in
the file in case of a crash.
Markus Elfring [Tue, 13 Sep 2016 09:32:22 +0000 (11:32 +0200)]
virtio_blk: Use kmalloc_array() in init_vq()
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Matt Redfearn [Tue, 11 Oct 2016 11:05:15 +0000 (12:05 +0100)]
virtio: console: Unlock vqs while freeing buffers
Commit c6017e793b93 ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b93 ("virtio: console: add locks around buffer removal in port unplug path") Cc: stable@vger.kernel.org Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>