During socket close, if there is a open record with tx context, it needs
to be be freed apart from freeing up plaintext and encrypted scatter
lists. This patch frees up the open record if present in tx context.
Also tls_free_both_sg() has been renamed to tls_free_open_rec() to
indicate that the free record in tx context is being freed inside the
function.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tls: Fix socket mem accounting error under async encryption
Current async encryption implementation sometimes showed up socket
memory accounting error during socket close. This results in kernel
warning calltrace. The root cause of the problem is that socket var
sk_forward_alloc gets corrupted due to access in sk_mem_charge()
and sk_mem_uncharge() being invoked from multiple concurrent contexts
in multicore processor. The apis sk_mem_charge() and sk_mem_uncharge()
are called from functions alloc_plaintext_sg(), free_sg() etc. It is
required that memory accounting apis are called under a socket lock.
The plaintext sg data sent for encryption is freed using free_sg() in
tls_encryption_done(). It is wrong to call free_sg() from this function.
This is because this function may run in irq context. We cannot acquire
socket lock in this function.
We remove calling of function free_sg() for plaintext data from
tls_encryption_done() and defer freeing up of plaintext data to the time
when the record is picked up from tx_list and transmitted/freed. When
tls_tx_records() gets called, socket is already locked and thus there is
no concurrent access problem.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Simek [Tue, 25 Sep 2018 06:32:50 +0000 (08:32 +0200)]
net: macb: Clean 64b dma addresses if they are not detected
Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The check for pci_is_pcie() is redundant here because all
chip versions >=18 are PCIe only anyway. In addition use
dma_set_mask_and_coherent() instead of separate calls to
pci_set_dma_mask() and pci_set_consistent_dma_mask().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be slightly simplified by acking even events we're not
interested in. In addition add a comment making clear that the
read has no functional purpose and is just a PCI commit.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nine obvious bug fixes mostly in individual drivers. The target fix
is of particular importance because it's CVE related."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: don't crash the host on invalid commands
scsi: ipr: System hung while dlpar adding primary ipr adapter back
scsi: target: iscsi: Use bin2hex instead of a re-implementation
scsi: target: iscsi: Use hex2bin instead of a re-implementation
scsi: lpfc: Synchronize access to remoteport via rport
scsi: ufs: Disable blk-mq for now
scsi: sd: Contribute to randomness when running rotational device
scsi: ibmvscsis: Ensure partition name is properly NUL terminated
scsi: ibmvscsis: Fix a stringop-overflow warning
Merge tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
I wrote:
"USB fixes for 4.19-rc6
Here are some small USB core and driver fixes for reported issues for
4.19-rc6.
The most visible is the oops fix for when the USB core is built into the
kernel that is present in 4.18. Turns out not many people actually do
that so it went unnoticed for a while. The rest is some tiny typec,
musb, and other core fixes.
All have been in linux-next with no reported issues."
* tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: mux: Take care of driver module reference counting
usb: core: safely deal with the dynamic quirk lists
usb: roles: Take care of driver module reference counting
USB: handle NULL config in usb_find_alt_setting()
USB: fix error handling in usb_driver_claim_interface()
USB: remove LPM management from usb_driver_claim_interface()
USB: usbdevfs: restore warning for nonsensical flags
USB: usbdevfs: sanitize flags more
Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
usb: musb: dsps: do not disable CPPI41 irq in driver teardown
Merge tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
I wrote:
"TTY/Serial driver fixes for 4.19-rc6
Here are a number of small tty and serial driver fixes for reported
issues for 4.19-rc6.
One should hopefully resolve a much-reported issue that syzbot has found
in the tty layer. Although there are still more issues there, getting
this fixed is nice to see finally happen.
All of these have been in linux-next for a while with no reported
issues."
* tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: imx: restore handshaking irq for imx1
tty: vt_ioctl: fix potential Spectre v1
tty: Drop tty->count on tty_reopen() failure
serial: cpm_uart: return immediately from console poll
tty: serial: lpuart: avoid leaking struct tty_struct
serial: mvebu-uart: Fix reporting of effective CSIZE to userspace
Revert "uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name"
This changes UAPI, breaking iwd and libell:
ell/key.c: In function 'kernel_dh_compute':
ell/key.c:205:38: error: 'struct keyctl_dh_params' has no member named 'private'; did you mean 'dh_private'?
struct keyctl_dh_params params = { .private = private,
^~~~~~~
dh_private
Fixes: 8a2336e549d3 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name") Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: James Morris <jmorris@namei.org>
cc: "Serge E. Hallyn" <serge@hallyn.com>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: <stable@vger.kernel.org> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) Fix multiqueue handling of coalesce timer in stmmac, from Jose
Abreu.
2) Fix memory corruption in NFC, from Suren Baghdasaryan.
3) Don't write reserved bits in ravb driver, from Kazuya Mizuguchi.
4) SMC bug fixes from Karsten Graul, YueHaibing, and Ursula Braun.
5) Fix TX done race in mvpp2, from Antoine Tenart.
6) ipv6 metrics leak, from Wei Wang.
7) Adjust firmware version requirements in mlxsw, from Petr Machata.
8) Fix autonegotiation on resume in r8169, from Heiner Kallweit.
9) Fixed missing entries when dumping /proc/net/if_inet6, from Jeff
Barnhill.
10) Fix double free in devlink, from Dan Carpenter.
11) Fix ethtool regression from UFO feature removal, from Maciej
Żenczykowski.
12) Fix drivers that have a ndo_poll_controller() that captures the
cpu entirely on loaded hosts by trying to drain all rx and tx
queues, from Eric Dumazet.
13) Fix memory corruption with jumbo frames in aquantia driver, from
Friedemann Gerold."
Until now, the Rx flow hash key was a 5-tuple (IP src, IP dst,
IP nextproto, L4 src port, L4 dst port) fixed value that we
configured at probe.
Add support for configuring this hash key at runtime.
We support all standard header fields configurable through ethtool,
but cannot differentiate between flow types, so the same hash key
is applied regardless of protocol.
We also don't support the discard option.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 24 Sep 2018 14:56:13 +0000 (16:56 +0200)]
net: mvneta: fix the remaining Rx descriptor unmapping issues
With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.
The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 24 Sep 2018 13:48:19 +0000 (15:48 +0200)]
ip_tunnel: be careful when accessing the inner header
Cong noted that we need the same checks introduced by commit 76c0ddd8c3a6
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The SPI protocol for the QCA7000 doesn't have any fault detection.
In order to increase the drivers reliability in noisy environments,
we could implement a write verification inspired by the enc28j60.
This should avoid situations were the driver wrongly assumes the
receive interrupt is enabled and miss all incoming packets.
This function is disabled per default and can be controlled via module
parameter wr_verify.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In tls_sw_sendmsg() and tls_sw_sendpage(), it is possible that the
uninitialised variable 'ret' gets passed to sk_stream_error(). So
initialise local variable 'ret' to '0. The warnings were detected by
'smatch' tool.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On processors with multi-engine crypto accelerators, it is possible that
multiple records get encrypted in parallel and their encryption
completion is notified to different cpus in multicore processor. This
leads to the situation where tls_encrypt_done() starts executing in
parallel on different cores. In current implementation, encrypted
records are queued to tx_ready_list in tls_encrypt_done(). This requires
addition to linked list 'tx_ready_list' to be protected. As
tls_decrypt_done() could be executing in irq content, it is not possible
to protect linked list addition operation using a lock.
To fix the problem, we remove linked list addition operation from the
irq context. We do tx_ready_list addition/removal operation from
application context only and get rid of possible multiple access to
the linked list. Before starting encryption on the record, we add it to
the tail of tx_ready_list. To prevent tls_tx_records() from transmitting
it, we mark the record with a new flag 'tx_ready' in 'struct tls_rec'.
When record encryption gets completed, tls_encrypt_done() has to only
update the 'tx_ready' flag to true & linked list add operation is not
required.
The changed logic brings some other side benefits. Since the records
are always submitted in tls sequence number order for encryption, the
tx_ready_list always remains sorted and addition of new records to it
does not have to traverse the linked list.
Lastly, we renamed tx_ready_list in 'struct tls_sw_context_tx' to
'tx_list'. This is because now, the some of the records at the tail are
not ready to transmit.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption") Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Sep 2018 19:21:33 +0000 (12:21 -0700)]
Merge branch 'few-NTF_ROUTER-related-updates'
Roopa Prabhu says:
====================
few NTF_ROUTER related updates
This series allows setting of NTF_ROUTER by an external
entity (eg BGP E-VPN control plane). Also fixes missing
netlink notification on neigh NTF_ROUTER flag changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
neighbour: send netlink notification if NTF_ROUTER changes
send netlink notification if neigh_update results in NTF_ROUTER
change and if NEIGH_UPDATE_F_ISROUTER is on. Also move the
NTF_ROUTER change function into a helper.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows admin setting of NTF_ROUTER flag
on a neighbour entry. This enables external control
plane (like bgp evpn) to manage neigh entries with
NTF_ROUTER flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saif Hasan [Fri, 21 Sep 2018 21:30:05 +0000 (14:30 -0700)]
mpls: allow routes on ip6gre devices
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
====================
net/sched: Add hardware specific counters to TC actions
Add hardware specific counters to TC actions which will be exported
through the netlink API. This makes troubleshooting TC flower offload
easier, as it possible to differentiate the packets being offloaded.
v2 - Rebased on latest net-next
====================
Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: Add hardware specific counters to TC actions
Add additional counters that will store the bytes/packets processed by
hardware. These will be exported through the netlink interface for
displaying by the iproute2 tc tool
Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several fixes for BPF sockmap to only allow sockets being attached in
ESTABLISHED state, from John.
2) Fix up the license to LGPL/BSD for the libc compat header which contains
fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Sep 2018 17:01:10 +0000 (10:01 -0700)]
Merge branch 'mvpp2-Add-txq-to-CPU-mapping'
Maxime Chevallier says:
====================
net: mvpp2: Add txq to CPU mapping
This short series adds XPS support to the mvpp2 driver, by mapping
txqs and CPUs. This comes with a patch using round-robin scheduling
for the HW to pick the next txq to transmit from, instead of the default
fixed-priority scheduling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: use round-robin scheduling for TX queues on the same CPU
This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: Yan Markman <ymarkman@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: support XPS by mapping TX queues to CPUs
Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.
Suggested-by : Yan Markman <ymarkman@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Reported-by: Friedemann Gerold <f.gerold@b-c-s.de> Reported-by: Michael Rauch <michael@rauch.be> Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de> Tested-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).
This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :
Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch series take care of the first round, we will
handle other drivers in future rounds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:52 +0000 (15:27 -0700)]
tun: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:51 +0000 (15:27 -0700)]
nfp: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:50 +0000 (15:27 -0700)]
bnxt: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:49 +0000 (15:27 -0700)]
bnx2x: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:48 +0000 (15:27 -0700)]
mlx5: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:47 +0000 (15:27 -0700)]
mlx4: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:46 +0000 (15:27 -0700)]
i40evf: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:45 +0000 (15:27 -0700)]
ice: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:44 +0000 (15:27 -0700)]
igb: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:43 +0000 (15:27 -0700)]
ixgb: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit af3e0fcf7887 ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:42 +0000 (15:27 -0700)]
fm10k: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:41 +0000 (15:27 -0700)]
ixgbevf: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:40 +0000 (15:27 -0700)]
ixgbe: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: Song Liu <songliubraving@fb.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Song Liu <songliubraving@fb.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:39 +0000 (15:27 -0700)]
bonding: use netpoll_poll_dev() helper
We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.
team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:38 +0000 (15:27 -0700)]
netpoll: make ndo_poll_controller() optional
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller().
NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch allows netpoll_poll_dev() to process NAPI
contexts even for drivers not providing ndo_poll_controller(),
allowing for following patches in NAPI drivers.
Also we export netpoll_poll_dev() so that it can be called
by bonding/team drivers in following patches.
Reported-by: Song Liu <songliubraving@fb.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Song Liu <songliubraving@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 23 Sep 2018 14:48:55 +0000 (17:48 +0300)]
mlxsw: Make MLXSW_SP1_FWREV_MINOR a hard requirement
Up until now, mlxsw tolerated firmware versions that weren't exactly
matching the required version, if the branch number matched. That
allowed the users to test various firmware versions as long as they were
on the right branch.
On the other hand, it made it impossible for mlxsw to put a hard lower
bound on a version that fixes all problems known to date. If a user had
a somewhat older FW version installed, mlxsw would start up just fine,
possibly performing non-optimally as it would use features that trigger
problematic behavior.
Therefore tweak the check to accept any FW version that is:
- on the same branch as the preferred version, and
- the same as or newer than the preferred version.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee writes:
"MFD fixes for v4.19
- Fix Dialog DA9063 regulator constraints issue causing failure in
probe
- Fix OMAP Device Tree compatible strings to match DT"
* tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: omap-usb-host: Fix dts probe of children
mfd: da9063: Fix DT probing with constraints
Merge tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"A set of fixes for x86:
- Resolve the kvmclock regression on AMD systems with memory
encryption enabled. The rework of the kvmclock memory allocation
during early boot results in encrypted storage, which is not
shareable with the hypervisor. Create a new section for this data
which is mapped unencrypted and take care that the later
allocations for shared kvmclock memory is unencrypted as well.
- Fix the build regression in the paravirt code introduced by the
recent spectre v2 updates.
- Ensure that the initial static page tables cover the fixmap space
correctly so early console always works. This worked so far by
chance, but recent modifications to the fixmap layout can -
depending on kernel configuration - move the relevant entries to a
different place which is not covered by the initial static page
tables.
- Address the regressions and issues which got introduced with the
recent extensions to the Intel Recource Director Technology code.
- Update maintainer entries to document reality"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Expand static page table for fixmap space
MAINTAINERS: Add X86 MM entry
x86/intel_rdt: Add Reinette as co-maintainer for RDT
MAINTAINERS: Add Borislav to the x86 maintainers
x86/paravirt: Fix some warning messages
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Fix exclusive mode handling of MBA resource
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
x86/intel_rdt: Fix unchecked MSR access
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
x86/intel_rdt: Global closid helper to support future fixes
x86/intel_rdt: Fix size reporting of MBA resource
x86/intel_rdt: Fix data type in parsing callbacks
x86/kvm: Use __bss_decrypted attribute in shared variables
x86/mm: Add .bss..decrypted section to hold shared variables
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"- Provide a strerror_r wrapper so lib/bpf can be built on systems
without _GNU_SOURCE
- Unbreak the man page generator when building out of tree"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf Documentation: Fix out-of-tree asciidoctor man page generation
tools lib bpf: Provide wrapper for strerror_r to build in !_GNU_SOURCE systems
====================
hv_netvsc: Support LRO/RSC in the vSwitch
The patch adds support for LRO/RSC in the vSwitch feature. It reduces
the per packet processing overhead by coalescing multiple TCP segments
when possible. The feature is enabled by default on VMs running on
Windows Server 2019 and later.
The patch set also adds ethtool command handler and documents.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO/RSC in the vSwitch is a feature available in Windows Server 2019
hosts and later. It reduces the per packet processing overhead by
coalescing multiple TCP segments when possible. This patch adds netvsc
driver support for this feature.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(userns)$ tcpdump -i usb_rndis0
tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted
Warning: Kernel filter failed: Bad file descriptor
tcpdump: can't remove kernel filter: Bad file descriptor
With this change it returns EOPNOTSUPP instead of EPERM.
See also https://github.com/the-tcpdump-group/libpcap/issues/689
Fixes: 08a00fea6de2 "net: Remove references to NETIF_F_UFO from ethtool." Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two additional fixes that are required in order for SGMII to
work correctly. This was discovered with using a copper SFP which would
make us use SGMII mode, we would actually leave the HW configured in its
default mode: Fiber.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: b53: Also include SGMII for mac_config and mac_link_state
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
net/decnet/dn_dev.c:1366:10: warning: address of array 'dev->name' will
always evaluate to 'true' [-Wpointer-bool-conversion]
dev->name ? dev->name : "???",
~~~~~^~~~ ~
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/116 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Oskolkov [Fri, 21 Sep 2018 18:17:16 +0000 (11:17 -0700)]
net/ipfrag: let ip[6]frag_high_thresh in ns be higher than in init_net
Currently, ip[6]frag_high_thresh sysctl values in new namespaces are
hard-limited to those of the root/init ns.
There are at least two use cases when it would be desirable to
set the high_thresh values higher in a child namespace vs the global hard
limit:
- a security/ddos protection policy may lower the thresholds in the
root/init ns but allow for a special exception in a child namespace
- testing: a test running in a namespace may want to set these
thresholds higher in its namespace than what is in the root/init ns
RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats
Clang warns when two declarations' section attributes don't match.
net/rds/ib_stats.c:40:1: warning: section does not match previous
declaration [-Wsection]
DEFINE_PER_CPU_SHARED_ALIGNED(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:142:2: note: expanded from macro
'DEFINE_PER_CPU_SHARED_ALIGNED'
DEFINE_PER_CPU_SECTION(type, name,
PER_CPU_SHARED_ALIGNED_SECTION) \
^
./include/linux/percpu-defs.h:93:9: note: expanded from macro
'DEFINE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name;
\
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
net/rds/ib.h:446:1: note: previous attribute is here
DECLARE_PER_CPU(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:111:2: note: expanded from macro
'DECLARE_PER_CPU'
DECLARE_PER_CPU_SECTION(type, name, "")
^
./include/linux/percpu-defs.h:87:9: note: expanded from macro
'DECLARE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name
^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
^
1 warning generated.
The initial definition was added in commit ec16227e1414 ("RDS/IB:
Infiniband transport") and the cache aligned definition was added in
commit e6babe4cc4ce ("RDS/IB: Stats and sysctls") right after. The
definition probably should have been updated in net/rds/ib.h, which is
what this patch does.
Link: https://github.com/ClangBuiltLinux/linux/issues/114 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 17:58:07 +0000 (10:58 -0700)]
net/ipv4: avoid compile error in fib_info_nh_uses_dev
net/ipv4/fib_frontend.c: In function 'fib_info_nh_uses_dev':
net/ipv4/fib_frontend.c:322:6: error: unused variable 'ret' [-Werror=unused-variable]
cc1: all warnings being treated as errors
Fixes: 78f2756c5fc0 ("net/ipv4: Move device validation to helper") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tcp: switch to Early Departure Time model
In the early days, pacing has been implemented in sch_fq (FQ)
in a generic way :
- SO_MAX_PACING_RATE could be used by any sockets.
- TCP would vary effective pacing rate based on CWND*MSS/SRTT
- FQ would ensure delays between packets based on current
sk->sk_pacing_rate, but with some quantum based artifacts.
(inflating RPC tail latencies)
- BBR then tweaked the pacing rate in its various phases
(PROBE, DRAIN, ...)
This worked reasonably well, but had the side effect that TCP RTT
samples would be inflated by the sojourn time of the packets in FQ.
Also note that when FQ is not used and TCP wants pacing, the
internal pacing fallback has very different behavior, since TCP
emits packets at the time they should be sent (with unreasonable
assumptions about scheduling costs)
Van Jacobson gave a talk at Netdev 0x12 in Montreal, about letting
TCP (or applications for UDP messages) decide of the Earliest
Departure Time, instead of letting packet schedulers derive it
from pacing rate.
Recent additions in linux provided SO_TXTIME and a new ETF qdisc
supporting the new skb->tstamp role
This patch series converts TCP and FQ to the same model.
This might in the future allow us to relax tight TSQ limits
(if FQ is present in the output path), and thus lower
number of callbacks to tcp_write_xmit(), thanks to batching.
This will be followed by FQ change allowing SO_TXTIME support
so that QUIC servers can let the pacing being done in FQ (or
offloaded if network device permits)
For example, a TCP flow rated at 24Mbps now shows a more meaningful RTT
A nice side effect of this patch series is a reduction of max/p99
latencies of RPC workloads, since the FQ quantum no longer adds
artifact.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:54 +0000 (08:51 -0700)]
net_sched: sch_fq: remove dead code dealing with retransmits
With the earliest departure time model, we no longer plan
special casing TCP retransmits. We therefore remove dead
code (since most compilers understood skb_is_retransmit()
was false)
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:52 +0000 (08:51 -0700)]
tcp: switch tcp and sch_fq to new earliest departure time model
TCP keeps track of tcp_wstamp_ns by itself, meaning sch_fq
no longer has to do it.
Thanks to this model, TCP can get more accurate RTT samples,
since pacing no longer inflates them.
This has the nice effect of removing some delays caused by FQ
quantum mechanism, causing inflated max/P99 latencies.
Also we might relax TCP Small Queue tight limits in the future,
since this new model allow TCP to build bigger batches, since
sch_fq (or a device with earliest departure time offload) ensure
these packets will be delivered on time.
Note that other protocols are not converted (they will probably
never be) so sch_fq has still support for SO_MAX_PACING_RATE
Tested:
Test showing FQ pacing quantum artifact for low-rate flows,
adding unexpected throttles for RPC flows, inflating max and P99 latencies.
The parameters chosen here are to show what happens typically when
a TCP flow has a reduced pacing rate (this can be caused by a reduced
cwin after few losses, or/and rtt above few ms)
MIBS="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
Before :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
19,82.78,5279,3825,482.02
After :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
20,49.94,128,63,3.18
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:50 +0000 (08:51 -0700)]
tcp: provide earliest departure time in skb->tstamp
Switch internal TCP skb->skb_mstamp to skb->skb_mstamp_ns,
from usec units to nsec units.
Do not clear skb->tstamp before entering IP stacks in TX,
so that qdisc or devices can implement pacing based on the
earliest departure time instead of socket sk->sk_pacing_rate
Packets are fed with tcp_wstamp_ns, and following patch
will update tcp_wstamp_ns when both TCP and sch_fq switch to
the earliest departure time mechanism.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:48 +0000 (08:51 -0700)]
net_sched: sch_fq: switch to CLOCK_TAI
TCP will soon provide per skb->tstamp with earliest departure time,
so that sch_fq does not have to determine departure time by looking
at socket sk_pacing_rate.
We chose in linux-4.19 CLOCK_TAI as the clock base for transports,
qdiscs, and NIC offloads.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:46 +0000 (08:51 -0700)]
tcp: switch tcp_clock_ns() to CLOCK_TAI base
TCP pacing is either implemented in sch_fq or internally.
We have the goal of being able to offload pacing on the NICS.
TCP will soon provide per skb skb->tstamp as early departure time.
Like ETF in commit 25db26a91364 ("net/sched: Introduce the ETF Qdisc")
we chose CLOCK_T as the clock base, so that TCP and pacers can share
a common clock, to get better RTT samples (without pacing artificially
inflating these samples).
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Fri, 21 Sep 2018 15:41:48 +0000 (16:41 +0100)]
net: hns3: Remove redundant hclge_get_port_type()
This patch removes hclge_get_port_type which is redundant.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF
Our VF has not implemented the ops for get_port_type. So when we executing
ethtool ethx cmd of VF, hns3_get_link_ksettings will return directly. And
we can not query anything.
To support get_link_ksettings for VF, this patch replaces get_port_type
with get_media_type. If the media type is HNAE3_MEDIA_TYPE_NONE,
hns3_get_link_ksettings will return link information of VF.
Fixes: 12f46bc1d447 ("net: hns3: Refine hns3_get_link_ksettings()") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Fri, 21 Sep 2018 15:41:46 +0000 (16:41 +0100)]
net: hns3: Add get_media_type ops support for VF
This patch adds the ops of get_media_type support for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are already multiple types packets statistics for error packets,
it's unnecessary to print them, which may affect the rx performance if
print too many.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Add unlikely for dma_mapping_error check
For dma_mapping_error is unlikely happened, this patch adds unlikely for
dma_mapping_error check.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Add nic state check before calling netif_tx_wake_queue
When nic down, it firstly calls netif_tx_stop_all_queues(), then calls
napi_disable(). But napi_disable() will wait current napi_poll finish,
it may call netif_tx_wake_queue(). This patch fixes it by add nic state
checking.
Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few "switch-case" codes missed handle for default case. For
some abnormal case, it should return error code instead of return 0.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix of most functions for vf are hclgevf. This patch renames the
function with inconsistent prefix.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix tqp array traversal condition for vf
There are two tqp_num variables "hdev->tqp_num" and "kinfo->tqp_num"
used in VF. "hdev->tqp_num" is the total tqp number allocated to the
VF, and "kinfo->tqp_num" indicates the tqp number being used by the
VF. Usually the two variables are equal. But for the case hdev->tqp_num
larger than rss_size_max, and num_tc is 1, "kinfo->tqp_num" will be
less than "hdev->tqp_num".
In original codes, "hdev->tqp_num" is always used to traverse the
tqp array of kinfo. It may cause null pointer error when "hdev->tqp_num"
is larger than "kinfo->tqp_num"
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some prefix of tx/rx statistic names are redundant, this patch modifies
these names.
The new prefix looks like below:
rxq#1_ -> rxq1_
txq#1_ -> txq1_
tx_dropped -> dropped
tx_wake -> wake
tx_busy -> busy
rx_dropped -> dropped
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For desc.data is already point to the address of struct member "data[6]",
it's unnecessary to use '&' to get its address. This patch unifies all
the type convert for dest.data, using "req = (struct name *)dest.data".
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a defect in hclge_ets_validate(). If each member of tc_tsa is
not IEEE_8021QAZ_TSA_ETS, the variable total_ets_bw won't be updated.
In this case, the check for value of total_ets_bw will fail. This patch
fixes it by checking total_ets_bw only after it has been updated.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Biju Das [Fri, 21 Sep 2018 14:25:43 +0000 (15:25 +0100)]
dt-bindings: net: ravb: Add support for r8a7744 SoC
Document RZ/G1N (R8A7744) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus Kusche reported that the I/O busy time in /proc/diskstats was not
updating properly on 4.18. This is because we started using ktime to
track elapsed time, and we convert nanoseconds to jiffies when we update
the partition counter. However, this gets rounded down, so any I/Os that
take less than a jiffy are not accounted for. Previously in this case,
the value of jiffies would sometimes increment while we were doing I/O,
so at least some I/Os were accounted for.
Let's convert the stats to use nanoseconds internally. We still report
milliseconds as before, now more accurately than ever. The value is
still truncated to 32 bits for backwards compatibility.
Andrew Lunn [Fri, 21 Sep 2018 13:52:26 +0000 (15:52 +0200)]
ravb: Disable Pause Advertisement
The previous commit to ravb had the side effect of making the PHY
advertise Pause and Asym Pause, which previously did not happen. By
default, phydev->supported has both forms of pause enabled, but
phydev->advertising does not. The new phy_remove_link_mode() copies
phydev->supported to phydev->advertising after removing the requested
link mode. These Pause configuration bits appears it stops the PHY
from completing Auto-Neg and the link remains down. Be explicit and
remove the Pause and Asym Pause modes, so restoring the old behavior.
Fixes: 41124fa64d4b ("net: ethernet: Add helper to remove a supported link mode") Reported-by: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: if_arp: use define instead of hard-coded value
Struct arpreq contains the name of the device. All other places in the
kernel, the define IFNAMSIZ is used to designate its size. But in
if_arp.h, a literal constant is used.
As it could be good reasons to use constants instead of the defines in
include files under uapi, it seems to be OK to use the define here,
without opening a can of worms in user-land.
This because if_arp.h includes netdevice.h, which also uses
IFNAMSIZ. For the distros I have checked, this also holds true for the
use-land side.
The series also fixes some incorrect indents.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>