Eric Dumazet [Wed, 5 Dec 2018 22:24:31 +0000 (14:24 -0800)]
tcp: Do not underestimate rwnd_limited
If available rwnd is too small, tcp_tso_should_defer()
can decide it is worth waiting before splitting a TSO packet.
This really means we are rwnd limited.
Fixes: 5615f88614a4 ("tcp: instrument how long TCP is limited by receive window") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 4 Dec 2018 17:37:57 +0000 (17:37 +0000)]
net: use skb_list_del_init() to remove from RX sublists
list_del() leaves the skb->next pointer poisoned, which can then lead to
a crash in e.g. OVS forwarding. For example, setting up an OVS VXLAN
forwarding bridge on sfc as per:
Fixes: 9af86f933894 ("net: core: fix use-after-free in __netif_receive_skb_list_core") Fixes: 7da517a3bc52 ("net: core: Another step of skb receive list processing") Fixes: a4ca8b7df73c ("net: ipv4: fix drop handling in ip_list_rcv() and ip_list_rcv_finish()") Fixes: d8269e2cbf90 ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 5 Dec 2018 23:51:41 +0000 (15:51 -0800)]
Merge tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes/updates from Vineet Gupta
- Missing reads{x}()/writes{x}() getting in the way of some drivers [Jose Abreu]
- Builds defaulting to ARCv2 ISA based configsa [Kevin Hilman]
- Misc fixes
* tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: io.h: Implement reads{x}()/writes{x}()
ARC: change defconfig defaults to ARCv2
arc: [devboards] Add support of NFSv3 ACL
ARC: mm: fix uninitialised signal code in do_page_fault
ARC: [plat-hsdk] Enable DW APB GPIO support
ARCv2: boot log unaligned access in use
ARC: IOC: panic if kernel was started with previously enabled IOC
ARC: remove redundant 'default n' from Kconfig
David Rientjes [Wed, 5 Dec 2018 23:45:54 +0000 (15:45 -0800)]
mm, thp: restore node-local hugepage allocations
This is a full revert of ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for
MADV_HUGEPAGE mappings") and a partial revert of 89c83fb539f9 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask").
By not setting __GFP_THISNODE, applications can allocate remote hugepages
when the local node is fragmented or low on memory when either the thp
defrag setting is "always" or the vma has been madvised with
MADV_HUGEPAGE.
Remote access to hugepages often has much higher latency than local pages
of the native page size. On Haswell, ac5b2c18911f was shown to have a
13.9% access regression after this commit for binaries that remap their
text segment to be backed by transparent hugepages.
The intent of ac5b2c18911f is to address an issue where a local node is
low on memory or fragmented such that a hugepage cannot be allocated. In
every scenario where this was described as a fix, there is abundant and
unfragmented remote memory available to allocate from, even with a greater
access latency.
If remote memory is also low or fragmented, not setting __GFP_THISNODE was
also measured on Haswell to have a 40% regression in allocation latency.
Restore __GFP_THISNODE for thp allocations.
Fixes: ac5b2c18911f ("mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings") Fixes: 89c83fb539f9 ("mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask") Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Mon, 3 Dec 2018 18:30:25 +0000 (10:30 -0800)]
acpi/nfit: Fix user-initiated ARS to be "ARS-long" rather than "ARS-short"
A "short" ARS (address range scrub) instructs the platform firmware to
return known errors. In contrast, a "long" ARS instructs platform
firmware to arrange every data address on the DIMM to be read / checked
for poisoned data.
The conversion of the flags in commit d3abaf43bab8 "acpi, nfit: Fix
Address Range Scrub completion tracking", changed the meaning of passing
'0' to acpi_nfit_ars_rescan(). Previously '0' meant "not short", now '0'
is ARS_REQ_SHORT. Pass ARS_REQ_LONG to restore the expected scrub-type
behavior of user-initiated ARS sessions.
Fixes: d3abaf43bab8 ("acpi, nfit: Fix Address Range Scrub completion tracking") Reported-by: Jacek Zloch <jacek.zloch@intel.com> Cc: Vishal Verma <vishal.l.verma@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Sat, 24 Nov 2018 18:47:04 +0000 (10:47 -0800)]
libnvdimm, pfn: Pad pfn namespaces relative to other regions
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
[1]: https://github.com/pmem/ndctl/issues/76
Fixes: cfe30b872058 ("libnvdimm, pmem: adjust for section collisions with...") Cc: <stable@vger.kernel.org> Reported-by: Patrick Geary <patrickg@supermicro.com> Tested-by: Patrick Geary <patrickg@supermicro.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 5 Dec 2018 22:11:48 +0000 (14:11 -0800)]
tools/testing/nvdimm: Align test resources to 128M
In preparation for libnvdimm growing new restrictions to detect section
conflicts between persistent memory regions, enable nfit_test to
allocate aligned resources. Use a gen_pool to allocate nfit_test's fake
resources in a separate address space from the virtual translation of
the same.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Tested-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Wed, 5 Dec 2018 21:28:01 +0000 (13:28 -0800)]
Merge tag 'for-linus-20181205' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A bit earlier in the week as usual, but there's a fix here that should
go in sooner rather than later.
Under a combination of circumstance, the direct issue path in blk-mq
could corrupt data. This wasn't easy to hit, but the ones that are
affected by it, seem to hit it pretty easily. Full explanation in the
patch. None of the regular filesystem and storage testing has
triggered it, even though it's been around since 4.19-rc1.
Outside of that, whitelist trim tweak for certain Samsung devices for
libata"
* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
blk-mq: fix corruption with direct issue
libata: whitelist all SAMSUNG MZ7KM* solid-state disks
David S. Miller [Wed, 5 Dec 2018 19:46:06 +0000 (11:46 -0800)]
Merge tag 'mac80211-for-davem-2018-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg:
====================
As it's been a while, we have various fixes for
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 5 Dec 2018 17:58:17 +0000 (09:58 -0800)]
Merge tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"A patch in 4.19 introduced a sanity check that was too strict and a
filesystem cannot be mounted.
This happens for filesystems with more than 10 devices and has been
reported by a few users so we need the fix to propagate to stable"
* tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable
Linus Torvalds [Wed, 5 Dec 2018 17:51:10 +0000 (09:51 -0800)]
Merge tag 'pm-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Revert a problematic recent commit that attempted to fix a system-wide
suspend issue related to the freezer"
* tag 'pm-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "exec: make de_thread() freezable"
Chris Chiu [Wed, 5 Dec 2018 06:48:56 +0000 (14:48 +0800)]
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G
Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Chris Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chris Chiu [Wed, 5 Dec 2018 06:48:55 +0000 (14:48 +0800)]
ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G
Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Chris Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chris Chiu [Wed, 5 Dec 2018 06:48:54 +0000 (14:48 +0800)]
ALSA: hda/realtek - Add support for Acer Aspire C24-860 headset mic
The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Chris Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chris Chiu [Wed, 5 Dec 2018 06:48:53 +0000 (14:48 +0800)]
ALSA: hda/realtek: ALC286 mic and headset-mode fixups for Acer Aspire U27-880
Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.
Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Chris Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of devm_thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Trond Myklebust [Mon, 3 Dec 2018 23:49:00 +0000 (18:49 -0500)]
SUNRPC: Don't force a redundant disconnection in xs_read_stream()
If the connection is broken, then xs_tcp_state_change() will take care
of scheduling the socket close as soon as appropriate. xs_read_stream()
just needs to report the error.
Trond Myklebust [Tue, 4 Dec 2018 12:52:11 +0000 (07:52 -0500)]
SUNRPC: Fix RPC receive hangs
The RPC code is occasionally hanging when the receive code fails to
empty the socket buffer due to a partial read of the data. When we
convert that to an EAGAIN, it appears we occasionally leave data in the
socket. The fix is to just keep reading until the socket returns
EAGAIN/EWOULDBLOCK.
Jouni Malinen [Wed, 5 Dec 2018 10:55:54 +0000 (12:55 +0200)]
cfg80211: Fix busy loop regression in ieee80211_ie_split_ric()
This function was modified to support the information element extension
case (WLAN_EID_EXTENSION) in a manner that would result in an infinite
loop when going through set of IEs that include WLAN_EID_RIC_DATA and
contain an IE that is in the after_ric array. The only place where this
can currently happen is in mac80211 ieee80211_send_assoc() where
ieee80211_ie_split_ric() is called with after_ric[].
This can be triggered by valid data from user space nl80211
association/connect request (i.e., requiring GENL_UNS_ADMIN_PERM). The
only known application having an option to include WLAN_EID_RIC_DATA in
these requests is wpa_supplicant and it had a bug that prevented this
specific contents from being used (and because of that, not triggering
this kernel bug in an automated test case ap_ft_ric) and now that this
bug is fixed, it has a workaround to avoid this kernel issue.
WLAN_EID_RIC_DATA is currently used only for testing purposes, so this
does not cause significant harm for production use cases.
Fixes: 2512b1b18d07 ("mac80211: extend ieee80211_ie_split to support EXTENSION") Cc: stable@vger.kernel.org Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: ignore NullFunc frames in the duplicate detection
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
CC: <stable@vger.kernel.org> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Wed, 28 Nov 2018 21:39:16 +0000 (22:39 +0100)]
mac80211: fix reordering of buffered broadcast packets
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 13 Nov 2018 19:32:13 +0000 (20:32 +0100)]
mac80211: ignore tx status for PS stations in ieee80211_tx_status_ext
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0cf4 ("mac80211: add ieee80211_tx_status_noskb") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Peter Shih [Tue, 27 Nov 2018 04:49:50 +0000 (12:49 +0800)]
tty: serial: 8250_mtk: always resume the device in probe.
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling") Signed-off-by: Peter Shih <pihsun@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Cc: stable <stable@vger.kernel.org> # 4.18 Cc: Florian Zumbiehl <florz@florz.de> Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
Harry Pan [Wed, 28 Nov 2018 16:40:41 +0000 (00:40 +0800)]
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Wed, 28 Nov 2018 16:25:58 +0000 (11:25 -0500)]
USB: Fix invalid-free bug in port_over_current_notify()
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Young Xiao [Wed, 28 Nov 2018 08:06:53 +0000 (08:06 +0000)]
staging: rtl8712: Fix possible buffer overrun
In commit 8b7a13c3f404 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
Fixes: 8b7a13c3f404 ("staging: r8712u: Fix possible buffer overrun") Signed-off-by: Young Xiao <YangX92@hotmail.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Mon, 12 Nov 2018 15:43:22 +0000 (09:43 -0600)]
dmaengine: cppi41: delete channel from pending list when stop channel
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes: 975faaeb9985 ("dma: cppi41: start tear down only if channel is busy") Cc: stable@vger.kernel.org # v3.15+ Signed-off-by: Bin Liu <b-liu@ti.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:37 +0000 (03:40 +0000)]
dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
DMA buffer descriptors aren't allocated from atomic context, so they
can use the less heavyweigth GFP_NOWAIT.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Robin Gong <yibin.gong@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:33 +0000 (03:40 +0000)]
dmaengine: imx-sdma: implement channel termination via worker
The dmaengine documentation states that device_terminate_all may be
asynchronous and need not wait for the active transfers to stop.
This allows us to move most of the functionality currently implemented
in the sdma channel termination function to run in a worker, outside
of any atomic context. Moving this out of atomic context has two
benefits: we can now sleep while waiting for the channel to terminate,
instead of busy waiting and the freeing of the dma descriptors happens
with IRQs enabled, getting rid of a warning in the dma mapping code.
As the termination is now async, we need to implement the
device_synchronize dma engine function which simply waits for the
worker to finish its execution.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Robin Gong <yibin.gong@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:28 +0000 (03:40 +0000)]
Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
This reverts commit fe5b85c656bc. The SDMA engine needs the descriptors to
be contiguous in memory. As the dma pool API is only able to provide a
single descriptor per alloc invocation there is no guarantee that multiple
descriptors satisfy this requirement. Also the code in question is broken
as it only allocates memory for a single descriptor, without looking at the
number of descriptors required for the transfer, leading to out-of-bounds
accesses when the descriptors are written.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Robin Gong <yibin.gong@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lucas Stach [Tue, 6 Nov 2018 03:40:25 +0000 (03:40 +0000)]
Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"
This reverts commit c1199875d327, as this depends on another commit
that is going to be reverted.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Robin Gong <yibin.gong@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Masahiro Yamada [Wed, 5 Dec 2018 06:27:19 +0000 (15:27 +0900)]
x86/build: Fix compiler support check for CONFIG_RETPOLINE
It is troublesome to add a diagnostic like this to the Makefile
parse stage because the top-level Makefile could be parsed with
a stale include/config/auto.conf.
Once you are hit by the error about non-retpoline compiler, the
compilation still breaks even after disabling CONFIG_RETPOLINE.
The easiest fix is to move this check to the "archprepare" like
this commit did:
829fe4aa9ac1 ("x86: Allow generating user-space headers without a compiler")
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Zhenzhong Duan <zhenzhong.duan@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com> Fixes: 4cd24de3a098 ("x86/retpoline: Make CONFIG_RETPOLINE depend on compiler support") Link: http://lkml.kernel.org/r/1543991239-18476-1-git-send-email-yamada.masahiro@socionext.com Link: https://lkml.org/lkml/2018/12/4/206 Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Wilcox [Fri, 30 Nov 2018 16:05:06 +0000 (11:05 -0500)]
dax: Fix unlock mismatch with updated API
Internal to dax_unlock_mapping_entry(), dax_unlock_entry() is used to
store a replacement entry in the Xarray at the given xas-index with the
DAX_LOCKED bit clear. When called, dax_unlock_entry() expects the unlocked
value of the entry relative to the current Xarray state to be specified.
In most contexts dax_unlock_entry() is operating in the same scope as
the matched dax_lock_entry(). However, in the dax_unlock_mapping_entry()
case the implementation needs to recall the original entry. In the case
where the original entry is a 'pmd' entry it is possible that the pfn
performed to do the lookup is misaligned to the value retrieved in the
Xarray.
Change the api to return the unlock cookie from dax_lock_page() and pass
it to dax_unlock_page(). This fixes a bug where dax_unlock_page() was
assuming that the page was PMD-aligned if the entry was a PMD entry with
signatures like:
Link: https://lkml.kernel.org/r/20181130154902.GL10377@bombadil.infradead.org Fixes: 9f32d221301c ("dax: Convert dax_lock_mapping_entry to XArray") Reported-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Matthew Wilcox <willy@infradead.org> Tested-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Russell King [Fri, 9 Nov 2018 17:01:05 +0000 (17:01 +0000)]
thermal: armada: fix legacy resource fixup
When the armada thermal module is inserted, removed and then reinserted,
the system panics as per the messages below. The reason is that "edit"
a live resource in the resource tree twice, and end up with it pointing
to some other hardware.
Editing live resources (resources that are part of the registered
resource tree) is not permissible - the resource tree is an ordered
set of resources, sorted by start address, and when a new resource is
inserted, it is validated that it (a) fits within its parent resource
and (b) does not overlap a neighbouring resource.
Get rid of this resource editing. We can instead adjust the return
value from ioremap() as ioremap() deals with the creation of page-
based mappings - provided the adjustment does not cross a page
boundary.
Baruch Siach [Tue, 4 Dec 2018 14:03:53 +0000 (16:03 +0200)]
net: mvpp2: fix phylink handling of invalid PHY modes
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Tue, 4 Dec 2018 14:03:52 +0000 (16:03 +0200)]
net: mvpp2: fix detection of 10G SFP modules
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab000b ("net: mvpp2: 1000baseX support") Cc: Maxime Chevallier <maxime.chevallier@bootlin.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 9 Nov 2018 16:44:14 +0000 (16:44 +0000)]
thermal: armada: fix legacy validity test sense
Commit 8c0e64ac4075 ("thermal: armada: get rid of the ->is_valid()
pointer") removed the unnecessary indirection through a function
pointer, but in doing so, also removed the negation operator too:
- if (priv->data->is_valid && !priv->data->is_valid(priv)) {
+ if (armada_is_valid(priv)) {
which results in:
armada_thermal f06f808c.thermal: Temperature sensor reading not valid
armada_thermal f2400078.thermal: Temperature sensor reading not valid
armada_thermal f4400078.thermal: Temperature sensor reading not valid
at boot, or whenever the "temp" sysfs file is read. Replace the
negation operator.
Fixes: 8c0e64ac4075 ("thermal: armada: get rid of the ->is_valid() pointer") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
ethernet: fman: fix wrong of_node_put() in probe function
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e7762 ("fsl/fman: Add FMan support") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jens Axboe [Wed, 5 Dec 2018 03:06:48 +0000 (20:06 -0700)]
blk-mq: fix corruption with direct issue
If we attempt a direct issue to a SCSI device, and it returns BUSY, then
we queue the request up normally. However, the SCSI layer may have
already setup SG tables etc for this particular command. If we later
merge with this request, then the old tables are no longer valid. Once
we issue the IO, we only read/write the original part of the request,
not the new state of it.
This causes data corruption, and is most often noticed with the file
system complaining about the just read data being invalid:
[ 235.934465] EXT4-fs error (device sda1): ext4_iget:4831: inode #7142: comm dpkg-query: bad extra_isize 24937 (inode size 256)
because most of it is garbage...
This doesn't happen from the normal issue path, as we will simply defer
the request to the hardware queue dispatch list if we fail. Once it's on
the dispatch list, we never merge with it.
Fix this from the direct issue path by flagging the request as
REQ_NOMERGE so we don't change the size of it before issue.
See also:
https://bugzilla.kernel.org/show_bug.cgi?id=201685
Tested-by: Guenter Roeck <linux@roeck-us.net> Fixes: 6ce3dd6eec1 ("blk-mq: issue directly if hw queue isn't busy in case of 'none'") Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
While trying to use the dma_mmap_*() interface, it was noticed that this
interface returns strange values when passed an incorrect length.
If neither of the if() statements fire then the return value is
uninitialized. In the worst case it returns 0 which means the caller
will think the function succeeded.
Fixes: 1655cf8829d8 ("ARM: dma-mapping: Remove traces of NOMMU code") Signed-off-by: Nathan Jones <nathanj439@gmail.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Vladimir Murzin [Fri, 23 Nov 2018 11:25:21 +0000 (12:25 +0100)]
ARM: 8815/1: V7M: align v7m_dma_inv_range() with v7 counterpart
Chris has discovered and reported that v7_dma_inv_range() may corrupt
memory if address range is not aligned to cache line size.
Since the whole cache-v7m.S was lifted form cache-v7.S the same
observation applies to v7m_dma_inv_range(). So the fix just mirrors
what has been done for v7 with a little specific of M-class.
Cc: Chris Cole <chris@sageembedded.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Chris Cole [Fri, 23 Nov 2018 11:20:45 +0000 (12:20 +0100)]
ARM: 8814/1: mm: improve/fix ARM v7_dma_inv_range() unaligned address handling
This patch addresses possible memory corruption when
v7_dma_inv_range(start_address, end_address) address parameters are not
aligned to whole cache lines. This function issues "invalidate" cache
management operations to all cache lines from start_address (inclusive)
to end_address (exclusive). When start_address and/or end_address are
not aligned, the start and/or end cache lines are first issued "clean &
invalidate" operation. The assumption is this is done to ensure that any
dirty data addresses outside the address range (but part of the first or
last cache lines) are cleaned/flushed so that data is not lost, which
could happen if just an invalidate is issued.
The problem is that these first/last partial cache lines are issued
"clean & invalidate" and then "invalidate". This second "invalidate" is
not required and worse can cause "lost" writes to addresses outside the
address range but part of the cache line. If another component writes to
its part of the cache line between the "clean & invalidate" and
"invalidate" operations, the write can get lost. This fix is to remove
the extra "invalidate" operation when unaligned addressed are used.
A kernel module is available that has a stress test to reproduce the
issue and a unit test of the updated v7_dma_inv_range(). It can be
downloaded from
http://ftp.sageembedded.com/outgoing/linux/cache-test-20181107.tgz.
v7_dma_inv_range() is call by dmac_[un]map_area(addr, len, direction)
when the direction is DMA_FROM_DEVICE. One can (I believe) successfully
argue that DMA from a device to main memory should use buffers aligned
to cache line size, because the "clean & invalidate" might overwrite
data that the device just wrote using DMA. But if a driver does use
unaligned buffers, at least this fix will prevent memory corruption
outside the buffer.
Signed-off-by: Chris Cole <chris@sageembedded.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
drm/amd/display: Fix overflow/truncation from strncpy.
[Why]
New GCC warnings for stringop-truncation and stringop-overflow help
catch common misuse of strncpy. This patch suppresses these warnings
by fixing bugs identified by them.
[How]
Since the parameter passed for name in amdpgu_dm_create_common_mode has
no fixed length, if the string is >= DRM_DISPLAY_MODE_LEN then
mode->name will not be null-terminated.
The truncation in fill_audio_info won't actually occur (and the string
will be null-terminated since the buffer is initialized to zero), but
the warning can be suppressed by using the proper buffer size.
This patch fixes both issues by using the real size for the buffer and
making use of strscpy (which always terminates).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
wentalou [Mon, 3 Dec 2018 02:49:50 +0000 (10:49 +0800)]
drm/amdgpu: enlarge maximum waiting time of KIQ
KIQ in VF’s init delayed by another VF’s reset,
which would cause late_init failed occasionally.
MAX_KIQ_REG_TRY enlarged from 20 to 80 would fix this issue.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Wentao Lou <Wentao.Lou@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Darrick J. Wong [Sun, 2 Dec 2018 16:38:07 +0000 (08:38 -0800)]
iomap: partially revert 4721a601099 (simulated directio short read on EFAULT)
In commit 4721a601099, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads. This causes infinite
splice() loops and assertion failures on generic/095 on overlayfs
because xfs only permit total success or total failure of a directio
operation. The underlying issue in the pipe splice code has now been
fixed by changing the pipe splice loop to avoid avoid reading more data
than there is space in the pipe.
Therefore, it's no longer necessary to simulate the short directio, so
remove the hack from iomap.
Fixes: 4721a601099 ("iomap: dio data corruption and spurious errors when pipes fill") Reported-by: Murphy Zhou <jencce.kernel@gmail.com> Ranted-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Tue, 4 Dec 2018 17:10:39 +0000 (09:10 -0800)]
Merge branch 'parisc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"On parisc, use -ffunction-sections compiler option when building
32-bit kernel modules to avoid sysfs-warnings when loading such
modules.
This got broken with kernel v4.18"
* 'parisc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Enable -ffunction-sections for modules on 32-bit kernel
Darrick J. Wong [Fri, 30 Nov 2018 18:37:49 +0000 (10:37 -0800)]
splice: don't read more than available pipe space
In commit 4721a601099, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads.
The brokenness is compounded by splice_direct_to_actor immediately
bailing on do_splice_to returning <= 0 without ever calling ->actor
(which empties out the pipe), so if userspace calls back we'll EFAULT
again on the full pipe, and nothing ever gets copied.
Therefore, teach splice_direct_to_actor to clamp its requests to the
amount of free space in the pipe and remove the simulated short read
from the iomap directio code.
Fixes: 4721a601099 ("iomap: dio data corruption and spurious errors when pipes fill") Reported-by: Murphy Zhou <jencce.kernel@gmail.com> Ranted-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Darrick J. Wong [Fri, 30 Nov 2018 20:32:38 +0000 (12:32 -0800)]
vfs: allow some remap flags to be passed to vfs_clone_file_range
In overlayfs, ovl_remap_file_range calls vfs_clone_file_range on the
lower filesystem's inode, passing through whatever remap flags it got
from its caller. Since vfs_copy_file_range first tries a filesystem's
remap function with REMAP_FILE_CAN_SHORTEN, this can get passed through
to the second vfs_copy_file_range call, and this isn't an issue.
Change the WARN_ON to look only for the DEDUP flag.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Eric Sandeen [Fri, 30 Nov 2018 15:55:57 +0000 (07:55 -0800)]
xfs: fix inverted return from xfs_btree_sblock_verify_crc
xfs_btree_sblock_verify_crc is a bool so should not be returning
a failaddr_t; worse, if xfs_log_check_lsn fails it returns
__this_address which looks like a boolean true (i.e. success)
to the caller.
(interestingly xfs_btree_lblock_verify_crc doesn't have the issue)
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Darrick J. Wong [Tue, 27 Nov 2018 19:01:43 +0000 (11:01 -0800)]
xfs: fix PAGE_MASK usage in xfs_free_file_space
In commit e53c4b598, I *tried* to teach xfs to force writeback when we
fzero/fpunch right up to EOF so that if EOF is in the middle of a page,
the post-EOF part of the page gets zeroed before we return to userspace.
Unfortunately, I missed the part where PAGE_MASK is ~(PAGE_SIZE - 1),
which means that we totally fail to zero if we're fpunching and EOF is
within the first page. Worse yet, the same PAGE_MASK thinko plagues the
filemap_write_and_wait_range call, so we'd initiate writeback of the
entire file, which (mostly) masked the thinko.
Drop the tricky PAGE_MASK and replace it with correct usage of PAGE_SIZE
and the proper rounding macros.
Fixes: e53c4b598 ("xfs: ensure post-EOF zeroing happens after zeroing part of a file") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
David S. Miller [Tue, 4 Dec 2018 16:47:44 +0000 (08:47 -0800)]
phy: Revert toggling reset changes.
This reverts:
ef1b5bf506b1 ("net: phy: Fix not to call phy_resume() if PHY is not attached") 8c85f4b81296 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 4 Dec 2018 16:22:02 +0000 (17:22 +0100)]
Merge branch 'bpf-verifier-resilience'
Alexei Starovoitov says:
====================
Three patches to improve verifier ability to handle pathological bpf
programs with a lot of branches:
- make sure prog_load syscall can be aborted
- improve branch taken analysis
- introduce per-insn complexity limit for unprivileged programs
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
malicious bpf program may try to force the verifier to remember
a lot of distinct verifier states.
Put a limit to number of per-insn 'struct bpf_verifier_state'.
Note that hitting the limit doesn't reject the program.
It potentially makes the verifier do more steps to analyze the program.
It means that malicious programs will hit BPF_COMPLEXITY_LIMIT_INSNS sooner
instead of spending cpu time walking long link list.
The limit of BPF_COMPLEXITY_LIMIT_STATES==64 affects cilium progs
with slight increase in number of "steps" it takes to successfully verify
the programs:
before after
bpf_lb-DLB_L3.o 1940 1940
bpf_lb-DLB_L4.o 3089 3089
bpf_lb-DUNKNOWN.o 1065 1065
bpf_lxc-DDROP_ALL.o 28052 | 28162
bpf_lxc-DUNKNOWN.o 35487 | 35541
bpf_netdev.o 10864 10864
bpf_overlay.o 6643 6643
bpf_lcx_jit.o 38437 38437
But it also makes malicious program to be rejected in 0.4 seconds vs 6.5
Hence apply this limit to unprivileged programs only.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
pathological bpf programs may try to force verifier to explode in
the number of branch states:
20: (d5) if r1 s<= 0x24000028 goto pc+0
21: (b5) if r0 <= 0xe1fa20 goto pc+2
22: (d5) if r1 s<= 0x7e goto pc+0
23: (b5) if r0 <= 0xe880e000 goto pc+0
24: (c5) if r0 s< 0x2100ecf4 goto pc+0
25: (d5) if r1 s<= 0xe880e000 goto pc+1
26: (c5) if r0 s< 0xf4041810 goto pc+0
27: (d5) if r1 s<= 0x1e007e goto pc+0
28: (b5) if r0 <= 0xe86be000 goto pc+0
29: (07) r0 += 16614
30: (c5) if r0 s< 0x6d0020da goto pc+0
31: (35) if r0 >= 0x2100ecf4 goto pc+0
Teach verifier to recognize always taken and always not taken branches.
This analysis is already done for == and != comparison.
Expand it to all other branches.
It also helps real bpf programs to be verified faster:
before after
bpf_lb-DLB_L3.o 2003 1940
bpf_lb-DLB_L4.o 3173 3089
bpf_lb-DUNKNOWN.o 1080 1065
bpf_lxc-DDROP_ALL.o 29584 28052
bpf_lxc-DUNKNOWN.o 36916 35487
bpf_netdev.o 11188 10864
bpf_overlay.o 6679 6643
bpf_lcx_jit.o 39555 38437
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
bpf: check pending signals while verifying programs
Malicious user space may try to force the verifier to use as much cpu
time and memory as possible. Hence check for pending signals
while verifying the program.
Note that suspend of sys_bpf(PROG_LOAD) syscall will lead to EAGAIN,
since the kernel has to release the resources used for program verification.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The warning gets triggered by an ancient lockdep check in the freezer:
(gdb) list *0xffffffff812ece06
0xffffffff812ece06 is in flush_old_exec (./include/linux/freezer.h:57).
52 * DO NOT ADD ANY NEW CALLERS OF THIS FUNCTION
53 * If try_to_freeze causes a lockdep warning it means the caller may deadlock
54 */
55 static inline bool try_to_freeze_unsafe(void)
56 {
57 might_sleep();
58 if (likely(!freezing(current)))
59 return false;
60 return __refrigerator(false);
61 }
I reviewed the ->cred_guard_mutex code, and the mutex is held across all
of exec() - and we always did this.
But there's this recent -rc4 commit:
> Chanho Min (1):
> exec: make de_thread() freezable
Qu Wenruo [Fri, 23 Nov 2018 01:06:36 +0000 (09:06 +0800)]
btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
bg_start=12018974720 bg_len=10888413184, invalid block group size, \
have 10888413184 expect (0, 10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
Masami Hiramatsu [Thu, 23 Aug 2018 17:16:12 +0000 (02:16 +0900)]
kprobes/x86: Fix instruction patching corruption when copying more than one RIP-relative instruction
After copy_optimized_instructions() copies several instructions
to the working buffer it tries to fix up the real RIP address, but it
adjusts the RIP-relative instruction with an incorrect RIP address
for the 2nd and subsequent instructions due to a bug in the logic.
This will break the kernel pretty badly (with likely outcomes such as
a kernel freeze, a crash, or worse) because probed instructions can refer
to the wrong data.
For example putting kprobes on cpumask_next() typically hits this bug.
cpumask_next() is normally like below if CONFIG_CPUMASK_OFFSTACK=y
(in this case nr_cpumask_bits is an alias of nr_cpu_ids):
This dump shows that the second MOV accesses *(nr_cpu_ids+3) instead of
the original *nr_cpu_ids. This leads to a kernel freeze because
cpumask_next() always returns 0 and for_each_cpu() never ends.
Fix this by adding 'len' correctly to the real RIP address while
copying.
[ mingo: Improved the changelog. ]
Reported-by: Michael Rodin <michael@rodin.online> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org # v4.15+ Fixes: 63fef14fc98a ("kprobes/x86: Make insn buffer always ROX and use text_poke()") Link: http://lkml.kernel.org/r/153504457253.22602.1314289671019919596.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org>
Saeed Mahameed [Sun, 2 Dec 2018 12:34:37 +0000 (14:34 +0200)]
net/mlx4_en: Fix build break when CONFIG_INET is off
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.
This fixes the following build break:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Sun, 2 Dec 2018 12:34:36 +0000 (14:34 +0200)]
net/mlx4_en: Change min MTU size to ETH_MIN_MTU
NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in
the RFC791 and in the network stack. Remove old mlx4_en only define for
it, which was set to wrong value.
Fixes: b80f71f5816f ("ethernet/mellanox: use core min/max MTU checking") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Fri, 30 Nov 2018 23:26:27 +0000 (00:26 +0100)]
macvlan: return correct error value
A MAC address must be unique among all the macvlan devices with the same
lower device. The only exception is the passthru [sic] mode,
which shares the lower device address.
When duplicate addresses are detected, EBUSY is returned when bringing
the interface up:
# ip link add macvlan0 link eth0 type macvlan
# read addr </sys/class/net/eth0/address
# ip link set macvlan0 address $addr
# ip link set macvlan0 up
RTNETLINK answers: Device or resource busy
Use correct error code which is EADDRINUSE, and do the check also
earlier, on address change:
# ip link set macvlan0 address $addr
RTNETLINK answers: Address already in use
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 30 Nov 2018 17:36:59 +0000 (01:36 +0800)]
sctp: kfree_rcu asoc
In sctp_hash_transport/sctp_epaddr_lookup_transport, it dereferences
a transport's asoc under rcu_read_lock while asoc is freed not after
a grace period, which leads to a use-after-free panic.
This patch fixes it by calling kfree_rcu to make asoc be freed after
a grace period.
Note that only the asoc's memory is delayed to free in the patch, it
won't cause sk to linger longer.
Thanks Neil and Marcelo to make this clear.
Fixes: 7fda702f9315 ("sctp: use new rhlist interface on sctp transport rhashtable") Fixes: cd2b70875058 ("sctp: check duplicate node before inserting a new transport") Reported-by: syzbot+0b05d8aa7cb185107483@syzkaller.appspotmail.com Reported-by: syzbot+aad231d51b1923158444@syzkaller.appspotmail.com Suggested-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 30 Nov 2018 16:59:08 +0000 (10:59 -0600)]
net/ibmvnic: Fix RTNL deadlock during device reset
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset") Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 78139c94dc8c ("net: vhost: lock the vqs one by one") moved the vq
lock to improve scalability, but introduced a possible deadlock in
vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding
the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the
spinlock is taken while holding vq->mutex.
Since calling vhost_poll_queue() doesn't require any lock, avoid the
deadlock by not taking vq->mutex.
Fixes: 78139c94dc8c ("net: vhost: lock the vqs one by one") Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set is for R-Car Gen3 Salvator-XS boards. If we do
the following method, the phy cannot link up correctly.
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
When resolving this issue after I got feedback from Andrew and Heiner,
I found an issue that the phy_device.c didn't call phy_resume()
if the PHY was not attached. So, patch 1 fixes it and add toggling
the phy reset to the micrel phy driver.
Changes from v1 (as RFC):
- No remove the current code of phy_device.c to avoid any side effects.
- Fix the mdio_bus_phy_resume() in phy_device.c.
- Add toggling the phy reset in micrel.c if the PHY is not attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: micrel: add toggling phy reset if PHY is not attached
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: Fix not to call phy_resume() if PHY is not attached
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sandipan Das [Mon, 3 Dec 2018 12:21:04 +0000 (17:51 +0530)]
bpf: powerpc64: optimize JIT passes for bpf function calls
Once the JITed images for each function in a multi-function program
are generated after the first three JIT passes, we only need to fix
the target address for the branch instruction corresponding to each
bpf-to-bpf function call.
This introduces the following optimizations for reducing the work
done by the JIT compiler when handling multi-function programs:
[1] Instead of doing two extra passes to fix the bpf function calls,
do just one as that would be sufficient.
[2] During the extra pass, only overwrite the instruction sequences
for the bpf-to-bpf function calls as everything else would still
remain exactly the same. This also reduces the number of writes
to the JITed image.
[3] Do not regenerate the prologue and the epilogue during the extra
pass as that would be redundant.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Prashant Bhole [Mon, 3 Dec 2018 09:09:24 +0000 (18:09 +0900)]
tun: remove skb access after netif_receive_skb
In tun.c skb->len was accessed while doing stats accounting after a
call to netif_receive_skb. We can not access skb after this call
because buffers may be dropped.
The fix for this bug would be to store skb->len in local variable and
then use it after netif_receive_skb(). IMO using xdp data size for
accounting bytes will be better because input for tun_xdp_one() is
xdp_buff.
Hence this patch:
- fixes a bug by removing skb access after netif_receive_skb()
- uses xdp data size for accounting bytes
Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()") Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It's not the same as in 7fe0ee09 patch described.
As 8139cp uses shared irq mode, other device irq will trigger
cp_interrupt to execute.
cp_change_mtu
-> cp_close
-> cp_open
In cp_close routine just before free_irq(), some interrupt may occur.
In my environment, cp_interrupt exectutes and IntrStatus is 0x4,
exactly TxOk. That will cause cp_tx to wake device queue.
As device queue is started, cp_start_xmit and cp_open will run at same
time which will cause kernel BUG.
For example:
[#] for tx descriptor
At start:
[#][#][#]
num_queued=3
After cp_init_hw->cp_start_hw->netdev_reset_queue:
[#][#][#]
num_queued=0
When 8139cp starts to work then cp_tx will check
num_queued mismatchs the complete_bytes.
The patch will check IntrMask before check IntrStatus in cp_interrupt.
When 8139cp interrupt is disabled, just return.
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 3 Dec 2018 07:19:33 +0000 (08:19 +0100)]
net: phy: don't allow __set_phy_supported to add unsupported modes
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
libata: whitelist all SAMSUNG MZ7KM* solid-state disks
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi> Signed-off-by: Jens Axboe <axboe@kernel.dk>
I noticed that the Android v3.0.8 kernel on droid4 is using different
keypad values from the mainline kernel and does not have issues with
keys occasionally being stuck until pressed again. Turns out there was
an earlier patch posted to fix this as "Input: omap-keypad: errata i689:
Correct debounce time", but it was never reposted to fix use macros
for timing calculations.
This updated version is using macros, and also fixes the use of the
input clock rate to use 32768KiHz instead of 32000KiHz. And we want to
use the known good Android kernel values of 3 and 6 instead of 2 and 6
in the earlier patch.
Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Teika Kazura [Mon, 3 Dec 2018 19:26:03 +0000 (11:26 -0800)]
Input: synaptics - enable SMBus for HP 15-ay000
SMBus works fine for the touchpad with id SYN3221, used in the HP 15-ay000
series,
This device has been reported in these messages in the "linux-input"
mailing list:
* https://marc.info/?l=linux-input&m=152016683003369&w=2
* https://www.spinics.net/lists/linux-input/msg52525.html
Lyude Paul [Sun, 25 Nov 2018 07:28:10 +0000 (23:28 -0800)]
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>