drm/i915: Apply correct ddi translation table for AML device
Amber Lake used the same gen graphics as Kaby Lake. Kernel driver
should configure KBL's DDI buffer setting for AML ULX as well.
So far, driver would load DDI translation table that used for
KBL H/S platform and apply it on AML devices. But AML is belong to
ULX series. This change will lead driver to apply KBL-Y's DDI table
for AML devices to avoid unexpected eDP/DP signal quality issue.
commit 'b9be78531d27 ("drm/i915/whl: Introducing
Whiskey Lake platform")' introduced WHL by moving some
of CFL IDs here and using the Spec information of "U43" for
most of IDs what appeared to be GT3.
However when propagating the change to Mesa, Lionel noticed
that based on number of execution unities the classification
here seems at least strange.
So, let's move for now with the information we trust more:
the number of EUs. So we are able to propagate this change
across the stack without getting stuck forever.
Reference: https://patchwork.freedesktop.org/patch/246695/ Fixes: b9be78531d27 ("drm/i915/whl: Introducing Whiskey Lake platform") Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180924234312.15017-1-rodrigo.vivi@intel.com
Ville Syrjälä [Thu, 4 Oct 2018 12:15:27 +0000 (15:15 +0300)]
drm/i915: Fix ILK-IVB sprite enable delays
Sprite enable on ILK-IVB may take two frames to complete
when the hardware is in big FIFO mode (LP1+). That is
not entirely great as it means the sprite enable may
actually happen one frame after we've already signalled
flip completion. At the very least crc checks may fail
due to the sprite not yet being visible when we expect it.
We already have code to deal with big FIFO mode when it
comes to the sprite scaling on IVB
(WaCxSRDisabledForSpriteScaling:ivb). Let's extend that
workaround to kick in whenever the sprite is in the process
of being enabled. Also ILK/SNB bspec has some notes to
indicate that we should most likely also do the sprite
scaling w/a on all three platforms, so let's do that as well.
Pretty easy to reproduce on SNB/IVB. ILK has proved more
elusive, but let's trust the spec and include it as well.
v2: Make sure the pipe is active before the vblank wait
drm/i915: Get rid of crtc->config in chv_data_lane_soft_reset
Fixing chv_set_phy_signal_level() still requires too many levels of
indirection to pass crtc_state along, but chv_data_lane_soft_reset()
already has a crtc_state we can use.
drm/i915: Get rid of crtc->config dereference in intel_dp_retrain_link
We're already using crtc_state here and made sure no modeset is
occurring by looking at conn_state->commit->hw_done, so there's
no need to dereference crtc->config.
drm/i915: Use crtc->state in intel_fbdev_init_bios
fbdev init shouldn't race with userspace since it's called from
intel_modeset_init, so it's safe to dereference crtc->state and
assume nothing changed yet.
drm/i915: Get rid of crtc->config from icl_pll_to_ddi_pll_sel
Pass the full state to intel_ddi_clk_select, so we can pass it
to icl_pll_to_ddi_pll_sel instead of passign the crtc and having
to dereference crtc->config
drm/i915: Make shared dpll functions take crtc_state, v3.
Do not rely on crtc->config any more. Remove the assertion from
ibx_pch_dpll_disable, because we the dpll state tracking should
already handle this case correctly.
Changes since v1:
- Fixup accidental early return in intel_prepare_shared_dpll, oops!
Changes since v2:
- Don't use the freed crtc_state in intel_crtc_disable_noatomic()
If we look at the correct state instead of crtc->config, we can nuke the
force parameter, and we cleanup a few more users of crtc->config at the
same time.
Chris Wilson [Fri, 5 Oct 2018 08:03:00 +0000 (09:03 +0100)]
drm/i915: Remove the global cache shrink & rcu barrier on allocation failure
Earlier, we reasoned that having idled the gpu under mempressure, that
would be a good time to trim our request slabs in order to perform the
next request allocation. We have stopped performing the global operation
on the device (no idling) and wish to make the allocation failure
handling more local, so out with the global barrier that may take a long
time.
Chris Wilson [Thu, 4 Oct 2018 08:21:19 +0000 (09:21 +0100)]
drm/i915: Only reset seqno if actually idle
Before we can reset the seqno, we have to be sure the engines are idle.
In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves
to be interrupted. We should only proceed to reset the seqno then if we
were not interrupted, and so also avoid overwriting the error status.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108133 Fixes: 6b048706f407 ("drm/i915: Forcibly flush unwanted requests in drop-caches") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181004082119.24970-1-chris@chris-wilson.co.uk
Ville Syrjälä [Wed, 3 Oct 2018 14:50:52 +0000 (17:50 +0300)]
drm/i915: Clean up early plane debugs
Print the plane hw state readout results in the common format
we already use for pipes and encoders. Also print some clearer
debug messages when we disable planes during the early phases
of state readout/sanitization.
Ville Syrjälä [Wed, 3 Oct 2018 14:50:17 +0000 (17:50 +0300)]
drm/i915: Use the correct crtc when sanitizing plane mapping
When we decide that a plane is attached to the wrong pipe we try
to turn off said plane. However we are passing around the crtc we
think that the plane is supposed to be using rather than the crtc
it is currently using. That doesn't work all that well because
we may have to do vblank waits etc. and the other pipe might
not even be enabled here. So let's pass the plane's current crtc to
intel_plane_disable_noatomic() so that it can its job correctly.
To do that semi-cleanly we also have to change the plane readout
to record the plane's visibility into the bitmasks of the crtc
where the plane is currently enabled rather than to the crtc
we want to use for the plane.
One caveat here is that our active_planes bitmask will get confused
if both planes are enabled on the same pipe. Fortunately we can use
plane_mask to reconstruct active_planes sufficiently since
plane_mask still has the same meaning (is the plane visible?)
during readout. We also have to do the same during the initial
plane readout as the second plane could clear the active_planes
bit the first plane had already set.
v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel)
Add Daniel's proposed comment to better document why we do this
Drop the redundant intel_set_plane_visible() call
Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe Cc: stable@vger.kernel.org Cc: Dennis <dennis.nezic@utoronto.ca> Cc: Daniel Vetter <daniel@ffwll.ch> Tested-by: Dennis <dennis.nezic@utoronto.ca> Tested-by: Peter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637 Fixes: b1e01595a66d ("drm/i915: Redo plane sanitation during readout") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181003145017.4527-1-ville.syrjala@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 3 Oct 2018 18:42:10 +0000 (21:42 +0300)]
drm/i915: Provide more clues as to why MST is/is not used
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
drm/i915/guc: Don't clear the cookie on doorbell destroy
If the HW has not processed the db invalidation request yet, clearing
the cookie can generate a db ring. We clear the cookie when we
(re-)allocate the doorbell so no need to do it on destroy as well as no
one is going to look at it while the doorbell is inactive
GuC stores some data in there, which might be stale after a reset.
We already reset the WQ head and tail, but more things are being moved
to the descriptor with the interface updates. Instead of trying to track
them one by one, always memset and init the descriptors from scratch
after GuC is loaded.
The code is also reorganized so that the above operations and the
doorbell creation are grouped as "client enabling"
v2: add proc_desc_fini for symmetry (Daniele), remove unneeded var init,
add guc_is_alive() (Michal)
Chris Wilson [Wed, 3 Oct 2018 11:09:41 +0000 (12:09 +0100)]
drm/i915/execlists: Flush the CS events before unpinning
Inside the execlists submission tasklet, we often make the mistake of
assuming that everything beneath the request is available for use.
However, the submission and the request live on two separate timelines,
and the request contents may be freed from an early retirement before we
have had a chance to run the submission tasklet (think ksoftirqd). To
safeguard ourselves against any mistakes, flush the tasklet before we
unpin the context if execlists still has a reference to this context.
v2: Pull hw_context->active tracking into schedule_in and schedule_out.
Chris Wilson [Mon, 1 Oct 2018 19:44:46 +0000 (20:44 +0100)]
drm/i915: Clear the error PTE just once on finish
We do not need to continually clear our dedicated PTE for error capture
as it will be updated and invalidated to the next object. Only at the
end do we wish to be sure that the PTE doesn't point back to any buffer.
Chris Wilson [Wed, 3 Oct 2018 08:24:22 +0000 (09:24 +0100)]
drm/i915: Handle incomplete Z_FINISH for compressed error states
The final call to zlib_deflate(Z_FINISH) may require more output
space to be allocated and so needs to re-invoked. Failure to do so in
the current code leads to incomplete zlib streams (albeit intact due to
the use of Z_SYNC_FLUSH) resulting in the occasional short object
capture.
v2: Check against overrunning our pre-allocated page array
v3: Drop Z_SYNC_FLUSH entirely
We have new tests and fixes in place since the feature was last
disabled. Try again for gen-9+ hardware and enable only PSR1 by default as
a first step.
v2: Remove typo fix and comment improvements (Rodrigo)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Jose Roberto de Souza <jose.souza@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: commit 2ee7dc497e34 ("drm/i915: disable PSR by default on HSW/BDW")
References: commit dcb2e993f3c0 ("Revert "drm/i915: Enable PSR by default on Valleyview and Cherryview."") Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Tested-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180928061117.12394-1-dhinakaran.pandiyan@intel.com
Andi Shyti [Tue, 2 Oct 2018 09:20:47 +0000 (12:20 +0300)]
drm/i915: fix wrong error number report
During driver load it's considered that the i915_driver_create()
function fails only in case of insufficient memory. Indeed, in
case of failure of i915_driver_create(), the load function
returns indiscriminately -ENOMEM ignoring the real cause of
failure.
In i915_driver_create() get the consistent error value from
drm_dev_init() and embed it in the pointer return value.
Chris Wilson [Tue, 2 Oct 2018 11:32:21 +0000 (12:32 +0100)]
drm/i915: Show actual alongside requested frequency in debugfs/i915_rps_boost_info
Previously we hesitated in adding the hw probe for the actual GPU
frequency for rps_boost as it is quite cumbersome, but given some
surprising HW behaviour it would be useful to know both the RPS boost
state and the actual HW state in one location.
Add plane alpha blending support with the different blend modes.
This has been tested on a icl to show the correct results,
on earlier platforms small rounding errors cause issues. But this
already happens case with fully transparant or fully opaque RGB8888
fb's.
The recommended HW workaround is to disable alpha blending when the
plane alpha is 0 (transparant, hide plane) or 0xff (opaque, disable blending).
This is easy to implement on any platform, so just do that.
The tests for userspace are also available, and pass on gen11.
Changes since v1:
- Change mistaken < 0xff0 to 0xff00.
- Only set PLANE_KEYMSK_ALPHA_ENABLE when plane alpha < 0xff00, ignore blend mode.
- Rework disabling FBC when per pixel alpha is used.
As DMC Package contain DMC FW for multiple steppings including default
stepping. This patch will help to load FW for that particular stepping,
if FW for that stepping is available, instead of loading default FW.
Chris Wilson [Mon, 1 Oct 2018 14:47:55 +0000 (15:47 +0100)]
drm/i915: Priority boost for waiting clients
Latency is in the eye of the beholder. In the case where a client stops
and waits for the gpu, give that request chain a small priority boost
(not so that it overtakes higher priority clients, to preserve the
external ordering) so that ideally the wait completes earlier.
v2: Tvrtko recommends to keep the boost-from-user-stall as small as
possible and to allow new client flows to be preferred for interactivity
over stalls.
Chris Wilson [Mon, 1 Oct 2018 14:47:54 +0000 (15:47 +0100)]
drm/i915: Pull scheduling under standalone lock
Currently, the backend scheduling code abuses struct_mutex into order to
have a global lock to manipulate a temporary list (without widespread
allocation) and to protect against list modifications. This is an
extraneous coupling to struct_mutex and further can not extend beyond
the local device.
Pull all the code that needs to be under the one true lock into
i915_scheduler.c, and make it so.
Chris Wilson [Mon, 1 Oct 2018 14:47:53 +0000 (15:47 +0100)]
drm/i915: Priority boost for new clients
Taken from an idea used for FQ_CODEL, we give the first request of a
new request flows a small priority boost. These flows are likely to
correspond with short, interactive tasks and so be more latency sensitive
than the longer free running queues. As soon as the client has more than
one request in the queue, further requests are not boosted and it settles
down into ordinary steady state behaviour. Such small kicks dramatically
help combat the starvation issue, by allowing each client the opportunity
to run even when the system is under heavy throughput load (within the
constraints of the user selected priority).
v2: Mark the preempted request as the start of a new flow, to prevent a
single client being continually gazumped by its peers.
Chris Wilson [Mon, 1 Oct 2018 12:32:04 +0000 (13:32 +0100)]
drm/i915: Combine multiple internal plists into the same i915_priolist bucket
As we are about to allow ourselves to slightly bump the user priority
into a few different sublevels, packthose internal priority lists
into the same i915_priolist to keep the rbtree compact and avoid having
to allocate the default user priority even after the internal bumping.
The downside to having an requests[] rather than a node per active list,
is that we then have to walk over the empty higher priority lists. To
compensate, we track the active buckets and use a small bitmap to skip
over any inactive ones.
v2: Use MASK of internal levels to simplify our usage.
v3: Prevent overflow when SHIFT is zero.
Chris Wilson [Mon, 1 Oct 2018 12:32:03 +0000 (13:32 +0100)]
drm/i915: Reserve some priority bits for internal use
In the next few patches, we will want to give a small priority boost to
some requests/queues but not so much that we perturb the user controlled
order. As such we will shift the user priority bits higher leaving
ourselves a few low priority bits for our internal bumping.
Jani Nikula [Wed, 5 Sep 2018 09:53:21 +0000 (12:53 +0300)]
drm/i915/dp: optimize eDP 1.4+ link config fast and narrow
We've opted to use the maximum link rate and lane count for eDP panels,
because typically the maximum supported configuration reported by the
panel has matched the native resolution requirements of the panel, and
optimizing the link has lead to problems.
With eDP 1.4 rate select method and DSC features, this is decreasingly
the case. There's a need to optimize the link parameters. Moreover,
already eDP 1.3 states fast link with fewer lanes is preferred over the
wide and slow. (Wide and slow should still be more reliable for longer
cable lengths.)
Additionally, there have been reports of panels failing on arbitrary
link configurations, although arguably all configurations they claim to
support should work.
Optimize eDP 1.4+ link config fast and narrow.
Side note: The implementation has a near duplicate of the link config
function, with just the two inner for loops turned inside out. Perhaps
there'd be a way to make this, say, more table driven to reduce the
duplication, but seems like that would lead to duplication in the table
generation. We'll also have to see how the link config optimization for
DSC turns out.
drm/i915/dp: Do not grab crtc modeset lock in intel_dp_detect()
A crtc modeset lock was added for link retraining but
intel_dp_retrain_link() knows to take the necessary locks since
commit c85d200e8321 ("drm/i915: Move SST DP link retraining into the
->post_hotplug() hook")
v2: Drop AUX power domain reference in the early return path
Fixes: c85d200e8321 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-4-dhinakaran.pandiyan@intel.com
drm/i915/dp: Restrict link retrain workaround to external monitors
Commit '3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check,
unconditionally during long pulse"")' applies a work around for sinks
that don't signal link loss. The work around does not need to have to be
that broad as the issue was seen with only one particular monitor; limit
this only for external displays as eDP features like PSR turn off the link
and the driver ends up retraining the link seeeing that link is not
synchronized.
Cc: Lyude Paul <lyude@redhat.com> Cc: Jan-Marek Glogowski <glogow@fbihome.de> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
References: 3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"") Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-2-dhinakaran.pandiyan@intel.com
drm/i915/dp: Fix link retraining comment in intel_dp_long_pulse()
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"") Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
Chris Wilson [Tue, 25 Sep 2018 08:31:59 +0000 (09:31 +0100)]
drm/i915/execlists: Avoid kicking priority on the current context
If the request is currently on the HW (in port 0), then we do not need
to kick the submission tasklet to evaluate whether we should be
preempting itself in order to execute it again.
We are bumping the priority of the first of a pair of requests running
in the current context. Then when evaluating preempt, we would see that
that our priority request is higher than the last executing request in
ELSP0 and so trigger preemption, not realising that our intended request
was already executing.
v2: As we assume state of the execlists->port[] that is only valid while
we hold the timeline lock we have to repeat some earlier tests that on
the validity of the node.
v3: Wrap guc submission under the timeline.lock as is now the way of all
things.
Use uniform prefixes for firmware path, version and size. Unify
alignments. Order macro groups as in the if ladder using them. Add
platform specific max firmware size macros for all platforms for clarity
in the if ladder. Place the max firmware size macros in the platform
specific macro groups.
Hans de Goede [Sun, 9 Sep 2018 13:34:56 +0000 (15:34 +0200)]
drm/i915: Check for panel orientation quirks on eDP panels
So far we have only been calling
drm_connector_init_panel_orientation_property(), which checks for
panel orientation quirks in the drm_panel_orientation_quirks.c file,
for DSI panels as so far only devices with DSI panels have had panels
which are not mounted up right.
The new GPD win2 device uses a portrait screen in a landscape case,
so now we've a device with an eDP panel which needs the panel-orientation
property to let the fbcon code and userspace know that the image needs to
be fixed-up.
This commit makes intel_edp_init_connector() call
drm_connector_init_panel_orientation_property() so that the property
gets added.
Chris Wilson [Wed, 26 Sep 2018 20:12:22 +0000 (21:12 +0100)]
drm/i915: Remove i915.enable_ppgtt override
Now that we are confident in providing full-ppgtt where supported,
remove the ability to override the context isolation.
v2: Remove faked aliasing-ppgtt for testing as it no longer is accepted.
v3: s/USES/HAS/ to match usage and reject attempts to load the module on
old GVT-g setups that do not provide support for full-ppgtt.
v4: Insulate ABI ppGTT values from our internal enum (later plans
involve moving ppGTT depth out of the enum, thus potentially breaking
ABI unless we document the current values).
Partial views are small but there can be many of them, and since the sg
list space for them is allocated pessimistically, we can save some slab by
trimming the unused tail entries.
Chris Wilson [Tue, 25 Sep 2018 08:31:58 +0000 (09:31 +0100)]
drm/i915/selftests: Smoketest preemption
Very light stress test to bombard the submission backends with a large
stream with requests of randomly assigned priorities. Preemption will be
occasionally requested, but unlikely to ever succeed! (Although we may
build a long queue of requests and so may trigger an attempt to inject a
preempt context, as we emit no batch, the arbitration window is limited
to between requests inside the ringbuffer. The likelihood of actually
causing a preemption event is therefore very small. A later variant
should try to improve the likelihood of preemption events!)
v2: Include a second pattern with more frequent preemption
Jani Nikula [Wed, 26 Sep 2018 13:34:14 +0000 (16:34 +0300)]
drm/i915/csr: bypass firmware request on i915.dmc_firmware_path=""
With i915.dmc_firmware_path="" it's obvious the intention is to disable
CSR firmware loading. Bypass the firmware request altogether in this
case, with more obvious debug logging.
Jani Nikula [Wed, 26 Sep 2018 13:34:13 +0000 (16:34 +0300)]
drm/i915/csr: keep max firmware size together with firmare name and version
Move max firmware size to the same if ladder with firmware name and
required version. This allows us to detect the missing max size for a
platform without actually loading the firmware, and makes the whole
thing easier to maintain.
We need to move the power get earlier to allow for early return in the
missing platform case. While at it, extend the comment on why we return
with the reference held on errors.
We also need to move the module parameter override later to reuse the
max firmware size, which is independent of the override.
v2: Add comment on why we leak the wakeref on errors (Chris)
SKL has IPC but it should not be set according to the WA, so lets
just mark as it don't have it to simply the code and avoid
unnecessary MMIO writes at every call to intel_enable_ipc().
drm/i915: Unset reset pch handshake when PCH is not present in one place
Right now RESET_PCH_HANDSHAKE_ENABLE is enabled all the times inside
of intel_power_domains_init_hw() and if PCH is NOP it is unsed in
i915_gem_init_hw().
So making skl_pch_reset_handshake() handle both cases and calling
it for the missing gens in intel_power_domains_init_hw().
Ivybridge have a different register and bits but with the same
objective so moving it too.
v2(Rodrigo):
- handling IVYBRIDGE case inside intel_pch_reset_handshake()
v4(Rodrigo and Ville):
- moving the enable/disable decision to callers
drm/i915/runtime_pm: Share code to enable/disable PCH reset handshake
Instead of have the same code spread into 4 platforms lets share it.
BXT do not have a PCH so here also handling this case by unseting
RESET_PCH_HANDSHAKE_ENABLE.
v2(Rodrigo):
- renamed to intel_pch_reset_handshake()
- added comment about why BXT need the bit to be unset
v3(Rodrigo and Ville):
- added bool have_pch to intel_pch_reset_handshake()
- added back BXT comment
Chris Wilson [Wed, 26 Sep 2018 10:47:18 +0000 (11:47 +0100)]
drm/i915: Avoid compiler warning for maybe unused gu_misc_iir
/kisskb/src/drivers/gpu/drm/i915/i915_irq.c: warning: 'gu_misc_iir' may be used uninitialized in this function [-Wuninitialized]: => 3120:10
Silence the compiler warning by ensuring that the local variable is
initialised and removing the guard that is confusing the older gcc.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Fixes: df0d28c185ad ("drm/i915/icl: GSE interrupt moves from DE_MISC to GU_MISC") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180926104718.17462-1-chris@chris-wilson.co.uk
Chris Wilson [Wed, 26 Sep 2018 10:47:07 +0000 (11:47 +0100)]
drm/i915: Convert to BITS_PER_TYPE
In commit 9144d75e22ca ("include/linux/bitops.h: introduce BITS_PER_TYPE"),
we made BITS_PER_TYPE available to all and now we can use the macro to
replace some open-coded computation of sizeof(T) * BITS_PER_BYTE.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180926104707.17410-1-chris@chris-wilson.co.uk
Ville Syrjälä [Tue, 18 Sep 2018 14:02:43 +0000 (17:02 +0300)]
drm/i915: Check fb stride against plane max stride
commit 4e0b83a567e2 ("drm/i915: Extract per-platform plane->check()
functions") removed the plane max stride check for sprite planes.
I was going to add it back when introducing GTT remapping for the
display, but after further thought it seems better to re-introduce
it separately.
So let's add the max stride check back. And let's do it in a nicer
form than what we had before and do it for all plane types (easy
now that we have the ->max_stride() plane vfunc).
Only sprite planes really need this for now since primary planes
are capable of scanning out the current max fb size we allow, and
cursors have more stringent stride checks elsewhere.
drm/i915: Enable RGB565 90/270 plane rotation for gen11 onwards.
From gen11 onwards RGB565 90/270 plane rotation is supported on hardware.
IGT: https://patchwork.freedesktop.org/series/48756/ Signed-off-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Rebase on top of current dinq (self), fix grammar (Ville).] Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1535373473-3594-3-git-send-email-juhapekka.heikkila@gmail.com
Chris Wilson [Sat, 22 Sep 2018 14:18:03 +0000 (15:18 +0100)]
drm/i915: Match code to comment and enforce ppgtt for execlists
Our execlist dispatch code requires a ppGTT so make sure we enforce that
option in intel_sanitize_enable_ppgtt(). The comment already tries to
explain that execlists requires ppgtt, but was written when gen8 may
have also taken the legacy path; so rewrite the code to match the
comment by using HAS_EXECLISTS() feature instead of the gen.
drm/i915: use for_each_pipe loop to assign crtc_mask
This cleanup patch makes changes to use for_each_pipe loop
during bit-mask assignment of allowed crtc with encoder.
changes:
- use BIT(i) macro instead of (1 << i) (Chris)
changes from V2:
- use int for consistency (Jani)
changes from V3:
- instead use enum pipe (Ville)
changes from V4:
- drop DP/HDMI changes, as already part of patch from ville
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180919083126.31805-1-mahesh1.kumar@intel.com
we are missing the execlists_submission_tasklet() invocation before the
execlists_reset_fini() implying that either the queue is empty, or we
failed to schedule and run the tasklet on finish. Add an assert so we
are sure that on unsubmitting the incomplete request after reset, the
queue is indeed populated.
This patch setup voltage swing before enabling
combo PHY DDI (shared with DSI).
Note that DSI voltage swing programming is for
high speed data buffers. HW automatically handles
the voltage swing for the low power data buffers.
v2: Rebase
v3: Address various review comments related to VSWING
programming (Jani N)
drm/i915/icl: Configure lane sequencing of combo phy transmitter
This patch set the loadgen select and latency optimization for
aux and transmit lanes of combo phy transmitters. It will be
used for MIPI DSI HS operations.
v2: Rebase
v3: Add empty line to make code more legible (Ville).
On skylake we can switch to a high quality scaler mode when only 1 out
of 2 scalers are used, but on GLK and later bit 28 has a different
meaning. Don't set it, and make clear the distinction between
SKL and later PS values.
drm/i915: Replace call to commit_planes_on_crtc with internal update, v2.
drm_atomic_helper_commit_planes_on_crtc calls begin_commit,
then plane_update hooks, then flush_commit. Because we keep our own
visibility tracking through plane_state->visible there's no need to
rely on the atomic hooks for this.
By explicitly writing our own helper, we can update visible planes
as needed, which is useful to make NV12 support work as intended.
Changes since v1:
- Reword commit message. (Matt Roper)
- Rename to intel_update_planes_on_crtc(). (Matt)
drm/i915: Make intel_crtc_disable_planes() use active planes mask.
This will only disable planes we actually had marked as visible in
crtc_state->visible_planes and cleans up intel_crtc_disable_plane()
slightly.
This is also useful for when we start enabling NV12 support for gen11,
in which we will make the separate Y plane visible, but ignore the
Y plane's state.
We need to assume the plane has been visible before, even if no CRTC
is assigned to the plane. This is because when enabling a nv12 plane
on gen11, we will have to enable an extra plane and make it visible
by marking it in crtc_state->active_planes for
intel_update_planes_on_crtc().
Additionally, clear visible flag in intel_plane_atomic_check, in case
we ever hit a bug with visibility. Our code implicitly assumes that
plane_state->visible is only true when crtc and fb are set,
so we will either null deref in intel_fbc_choose_crtc() or
do something bad during the actual commit which cares even more.
Changes since v1:
- Unconditionally clear crtc_state->active_planes as well.
- Reword commit message, since this is now a preparation patch for
NV12 Y / UV plane linking.
While we may not update new_crtc_state, we may clear active_planes
if the new cursor update state will disable the cursor, but we fail
after. If this is immediately followed by a modeset disable, we may
soon not disable the planes correctly when we start depending on
active_planes.
Changes since v1:
- Clarify why we cannot swap crtc_state. (Matt)
Dave Airlie [Thu, 20 Sep 2018 23:52:34 +0000 (09:52 +1000)]
Merge branch 'drm-next-4.20' of git://people.freedesktop.org/~agd5f/linux into drm-next
This is a new pull for drm-next on top of last weeks with the following
changes:
- Fixed 64 bit divide
- Fixed vram type on vega20
- Misc vega20 fixes
- Misc DC fixes
- Fix GDS/GWS/OA domain handling
Previous changes from last week:
amdgpu/kfd:
- Picasso (new APU) support
- Raven2 (new APU) support
- Vega20 enablement
- ACP powergating improvements
- Add ABGR/XBGR display support
- VCN JPEG engine support
- Initial xGMI support
- Use load balancing for engine scheduling
- Lots of new documentation
- Rework and clean up i2c and aux handling in DC
- Add DP YCbCr 4:2:0 support in DC
- Add DMCU firmware loading for Raven (used for ABM and PSR)
- New debugfs features in DC
- LVDS support in DC
- Implement wave kill for gfx/compute (light weight reset for shaders)
- Use AGP aperture to avoid gart mappings when possible
- GPUVM performance improvements
- Bulk moves for more efficient GPUVM LRU handling
- Merge amdgpu and amdkfd into one module
- Enable gfxoff and stutter mode on Raven
- Misc cleanups
Chris Wilson [Thu, 20 Sep 2018 19:59:48 +0000 (20:59 +0100)]
drm/i915/execlists: Onion unwind for logical_ring_init() failure
Fix up the error unwind for logical_ring_init() failing by moving the
cleanup into the callers who own the various bits of state during
initialisation, so we don't forget to free the state allocated by the
caller.
Chris Wilson [Thu, 20 Sep 2018 16:13:43 +0000 (17:13 +0100)]
drm/i915: Park the GPU on module load
Once we have flushed the first request through the system to both load a
context and record the default state; tell the GPU to park and idle
itself, putting itself immediately (hopefully at least) into a
powersaving state, and allowing ourselves to start from known state
after setting up all our bookkeeping.
Chris Wilson [Thu, 20 Sep 2018 14:49:34 +0000 (15:49 +0100)]
drm/i915/selftests: Live tests emit requests and so require rpm
As we emit requests or touch HW directly for some of the live tests, the
requirement is that we hold the rpm wakeref before doing so. We want a
mix of granularity since we will want to test runtime suspend, so try to
mark up only the critical sections where we need rpm for the live test.
Chris Wilson [Wed, 19 Sep 2018 20:54:32 +0000 (21:54 +0100)]
drm/i915/guc: Restore preempt-context across S3/S4
Stolen memory is lost across S4 (hibernate) or S3-RST as it is a portion
of ordinary volatile RAM. As we allocate our rings from stolen, this may
include the rings used for our preempt context and their breadcrumb
instructions. In order to allow preemption following hibernation and
loss of stolen memory, we therefore need to repopulate the instructions
inside the lost ring upon resume. To handle both module load and resume,
we simply defer constructing the ring to first use.
Chris Wilson [Thu, 20 Sep 2018 10:58:09 +0000 (11:58 +0100)]
drm/i915/selftests: Basic stress test for rapid context switching
We need to exercise the HW and submission paths for switching contexts
rapidly to check that features such as execlists' wa_tail are adequate.
Plus it's an interesting baseline latency metric.
v2: Check the initial request for allocation errors
v3: Use finite waits for more robust handling of broken code