Olof Johansson [Fri, 1 Sep 2017 23:41:42 +0000 (16:41 -0700)]
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
Olof Johansson [Wed, 30 Aug 2017 16:58:03 +0000 (09:58 -0700)]
Merge tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.14, take 3
One new board, and a revert of a patch relying on a binding not stable
enough so that we can commit to it.
* tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3
Maxime Ripard [Fri, 25 Aug 2017 18:36:48 +0000 (20:36 +0200)]
arm: dts: sunxi: Revert EMAC changes
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Fri, 25 Aug 2017 18:36:48 +0000 (20:36 +0200)]
arm64: dts: allwinner: Revert EMAC changes
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Arnd Bergmann [Thu, 24 Aug 2017 13:49:06 +0000 (15:49 +0200)]
Merge tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "second round of Rockchip dts32 changes for 4.14" from Heiko Stübner:
A lot of attention for the rv1108 soc targetted at media-processing
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
* tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: rockchip: add cpu power supply for rv1108 evb
ARM: dts: rockchip: add cpu opp table for rv1108
ARM: dts: rockchip: add rk322x iommu nodes
ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evb
ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evb
ARM: dts: rockchip: add pwm backlight for rv1108 evb
ARM: dts: rockchip: add pwm dt nodes for rv1108
ARM: dts: rockchip: add spi dt node for rv1108
ARM: dts: rockchip: add saradc support for rv1108
ARM: dts: rockchip: add watchdog dt node for rv1108
ARM: dts: rockchip: add i2c dt nodes for rv1108
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
ARM: dts: rockchip: add more iommu nodes on rk3288
ARM: dts: rockchip: convert rk3288 device tree files to 64 bits
ARM: dts: rockchip: add spi node and spi pinctrl on rk3228/rk3229
Arnd Bergmann [Thu, 24 Aug 2017 11:10:12 +0000 (13:10 +0200)]
Merge tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "Aspeed devicetree updates for 4.14" from Joel Stanley:
- fix to expose the full flash windows on ast2400.
* tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
Frank Wang [Mon, 21 Aug 2017 08:39:28 +0000 (16:39 +0800)]
ARM: dts: rockchip: enable usb for rv1108-evb
Rockchip's rv1108-evb board has one usb otg controller and one usb
host controller, each usb controller connect with one usb-phy port
through UTMI+ interface. This patch enables them to support usb on
rv1108-evb board.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Arnd Bergmann [Tue, 22 Aug 2017 15:46:18 +0000 (17:46 +0200)]
Merge tag 'davinci-for-v4.14/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "Add device-tree node for display on Lego Mindstorms EV3" from Sekhar Nori:
* tag 'davinci-for-v4.14/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lego-ev3: Add node for LCD display
Arnd Bergmann [Tue, 22 Aug 2017 13:31:38 +0000 (15:31 +0200)]
Merge tag 'zynq-dt-for-4.14' of https://github.com/Xilinx/linux-xlnx into next/dt
Pull "arm: Xilinx Zynq DT fixes for v4.14" from Michal Simek:
- Remove earlycon
- Use C pre-processor
- Add fpga full region
- Add ethernet-phy as device-type
- Add adv7511 nodes to zc70x
* tag 'zynq-dt-for-4.14' of https://github.com/Xilinx/linux-xlnx:
arm: zynq: Remove earlycon from bootargs
arm: zynq: Use C pre-processor for includes in dts
arm: zynq: Label whole PL part as fpga_full region
arm: zynq: Add device-type property for zynq ethernet phy nodes
arm: zynq: Add adv7511 on i2c bus for zc70x
Linus Walleij [Tue, 22 Aug 2017 07:28:20 +0000 (09:28 +0200)]
ARM: dts: augment Ux500 to use DT cpufreq
This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.
Michal Simek [Tue, 16 Feb 2016 08:49:27 +0000 (09:49 +0100)]
arm: zynq: Remove earlycon from bootargs
Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 7 Apr 2016 09:28:12 +0000 (11:28 +0200)]
arm: zynq: Use C pre-processor for includes in dts
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Chen-Yu Tsai [Thu, 17 Aug 2017 03:40:48 +0000 (11:40 +0800)]
ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:
- 2GB LPDDR3 DRAM
- 8GB eMMC
- Micro-SD card slot
- HDMI output
- Headset (stereo + mic) jack
- Onboard mic
- Gigabit Ethernet with RTL8211E transceiver
- Ampak AP6212 WiFi + BT
- USB OTG connector
- USB-to-SATA bridge connected through a USB 2.0 hub
- Consumer IR receiver
- MIPI DSI LCD panel connector
- Camera interface (parallel and MIPI CSI) connector
- 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
- Raspberry Pi 2 compatible GPIO header
Arnd Bergmann [Fri, 18 Aug 2017 21:12:30 +0000 (23:12 +0200)]
Merge tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Add RZ/G1M (r8a7743) binding to apmu driver
This allows SMP to be supported on the RZ/G1M SoC
* Add bindings for iW-RainboW-G22D-SODIMM RZ/G1E SODIMM development kit
This is in preparation for adding DTS to support this hardware
* tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: apmu: Document r8a7743 support
ARM: shmobile: document iW-RainboW-G22D SODIMM SOM Development Platform
ARM: shmobile: document iW-RainboW-G22M-SM SODIMM System on Module
Arnd Bergmann [Fri, 18 Aug 2017 21:10:31 +0000 (23:10 +0200)]
Merge tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Enable second CPU core on RZ/G1M (r8a7743)
The RZ/G1M has two CA15 cores running at up to 1.5GHz
* Enable frequency scaling on RZ/G1M (r8a7743)
* Add six I2C cores to RZ/G1M (r8a7743) SoC DT
This is a step towards enabling these cores on boards that use this SoC
* Add CEC clock for HDMI transmitter to R-Car M2-W (r8a7791) Koelsch
Hans Verkuil says "The adv7511 on the Koelsch board has a 12 MHz fixed
clock for the CEC block. Specify this in the dts to enable CEC support."
* Add PFC support to RZ/G1E (r8a7745) SoC and add Ethernet and SCIF2
pins to SK-RZG1E board.
This allows the kernel to control multiplexed pins for Ethernet
and SCIF2 rather than relying on setup inherited at boot.
* tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat string
ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat string
ARM: dts: r8a7743: Add OPP table for frequency scaling
ARM: dts: r8a7743: Add APMU node and second CPU core
ARM: dts: koelsch: Add CEC clock for HDMI transmitter
ARM: dts: sk-rzg1e: add Ether pins
ARM: dts: sk-rzg1e: add SCIF2 pins
ARM: dts: r8a7745: add PFC support
ARM: dts: r8a7743: Add I2C DT support
Arnd Bergmann [Fri, 18 Aug 2017 21:02:58 +0000 (23:02 +0200)]
Merge tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.14-rc1" from Thierry Reding:
One fix for Tegra124 to hook the host1x device up with the SMMU.
The remainder of this enables USB device mode on a couple of boards
where the port is currently unused.
* tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable UDC on AC100
ARM: tegra: Enable UDC on Jetson TK1
ARM: tegra: Enable UDC on Dalmore
ARM: tegra: Enable UDC on Beaver
ARM: tegra: Register host1x node with IOMMU binding on Tegra124
Arnd Bergmann [Fri, 18 Aug 2017 21:00:27 +0000 (23:00 +0200)]
Merge tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.14" from Shawn Guo:
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
* tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-bx50v3: Enable i2c recovery mechanism
ARM: dts: imx6q-apalis-eval: add support for Apalis Evaluation Board
ARM: dts: imx6: add support for Toradex Ixora V1.1 carrier board
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: use i2c from dwc hdmi
ARM: dts: imx6q-apalis-ixora: add camera i2c bus definition
ARM: dts: imx6q-apalis-ixora: get rid of obsolete fusion comment
ARM: dts: imx6qdl-apalis: reword cam i2c comment
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: get rid of tegra legacy gen1_i2c comment
ARM: dts: imx6q-apalis-ixora: combine aliases
ARM: dts: imx6qdl-apalis: split usdhc1 pinctrl to support 4- and 8-bit
ARM: dts: imx6q-apalis-ixora: fix usdhc2 pinctrl property
ARM: dts: imx6ul-liteboard: Support poweroff
ARM: dts: imx: add CX9020 Embedded PC device tree
ARM: dts: imx53: add alternative UART2 configuration
ARM: dts: imx53: add srtc node
dt-bindings: arm: Add entry for Beckhoff CX9020
ARM: dts: i.MX25: add RNGB node to dtsi
ARM: dts: imx6ul-14x14-evk: Remove unrelated pin from ENET group
ARM: dts: imx7d-sdb: Add flexcan support
ARM: dts: imx7-colibri: add NAND support
...
Arnd Bergmann [Fri, 18 Aug 2017 20:57:43 +0000 (22:57 +0200)]
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
Arnd Bergmann [Fri, 18 Aug 2017 20:55:20 +0000 (22:55 +0200)]
Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
ARM: dts: am57xx-beagle-x15: Add support for rev C
ARM: dts: dra71-evm: Add pinmux configuration for MMC
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
ARM: dts: dra72-evm: Add pinmux configuration for MMC
ARM: dts: am572x-idk: Add pinmux configuration for MMC
ARM: dts: am571x-idk: Add pinmux configuration for MMC
ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
ARM: dts: dra7-evm: Add pinmux configuration for MMC
ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
Chen-Yu Tsai [Thu, 3 Aug 2017 08:14:11 +0000 (16:14 +0800)]
ARM: sun8i: a83t: h8homlet-v2: Enable USB ports
The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed
to a USB host port on the board. The other USB host port is routed to
USB OTG controller.
Chen-Yu Tsai [Thu, 3 Aug 2017 08:14:10 +0000 (16:14 +0800)]
ARM: sun8i: a83t: cubietruck-plus: Enable onboard USB peripherals
The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0,
and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C
control interface is not connected.
This patch enables both EHCI controllers, adds a device node for the
USB hub, and includes sunxi-common-regulators.dtsi for the VBUS
regulators. The existing reg_vcc3v3 is dropped as it is also available
in the set of common regulators. Other unused regulators are disabled.
Chen-Yu Tsai [Thu, 3 Aug 2017 08:14:08 +0000 (16:14 +0800)]
ARM: sun8i: a83t: Add USB PHY and host device nodes
The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for
USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is
the host controller for HSIC. OTG is not added yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rafał Miłecki [Thu, 17 Aug 2017 09:05:14 +0000 (11:05 +0200)]
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
This uses trigger-sources documented in commit 80dc6e1cd85fc ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
Jason Uy [Tue, 15 Aug 2017 17:26:00 +0000 (10:26 -0700)]
ARM: dts: cygnus: Enable Performance Monitoring Unit
Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Robert Nelson [Wed, 16 Aug 2017 16:50:53 +0000 (11:50 -0500)]
ARM: dts: am57xx-beagle-x15: Add support for rev C
Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.
This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]
Rev C is now in full production and boards are available for end users.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Nishanth Menon <nm@ti.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Arnd Bergmann [Thu, 17 Aug 2017 08:58:50 +0000 (10:58 +0200)]
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit DT changes for v4.14" from Kevin Hilman:
- update clock controler for use as reset controller
- misc. updates/fixups/improvements
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson6: use stable UART bindings
ARM: dts: meson: mark the clock controller also as reset controller
ARM: dts: meson: add a node which describes the SRAM
ARM: dts: meson8b: use the existing wdt node to override the compatible
ARM: dts: meson8: add the PWM controller nodes
ARM: dts: move the pwm_ab and pwm_cd nodes to meson.dtsi
Arnd Bergmann [Thu, 17 Aug 2017 08:56:37 +0000 (10:56 +0200)]
Merge tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS for 4.14" from Santosh Shilimkar:
Contents:
- ti-sci power domain, clock and reset controller support
- DSP nodes for k2h/k2l/k2e evms
- DSP CMA memory pools for k2h/k2l/k2e/keg evms
- MMC/hsmmc suport for k2g
- eDMA support for k2g
- DCAN support for k2g
* tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (22 commits)
ARM: dts: keystone-k2g-ice: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2g: Add DSP node
ARM: dts: k2g: Add DCAN nodes
dt-bindings: net: c_can: Update binding for clock and power-domains property
ARM: dts: keystone-k2g-evm: Enable MMC0 and MMC1
ARM: dts: keystone-k2g: add MMC0 and MMC1 nodes
ARM: dts: keystone-k2g: Add eDMA nodes
dt-bindings: ti,omap-hsmmc: Add 66AK2G mmc controller
dt-bindings: ti,edma: Add 66AK2G specific information
ARM: dts: keystone-k2g: Add gpio nodes
ARM: dts: keystone-k2e-evm: Add and enable DSP CMA memory pool
ARM: dts: keystone-k2l-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2hk-evm: Add and enable common DSP CMA memory pool
ARM: dts: keystone-k2e: Add DSP node
ARM: dts: keystone-k2l: Add DSP nodes
ARM: dts: keystone-k2hk: Add DSP nodes
ARM: dts: keystone-k2g: Add TI SCI reset-controller node
ARM: dts: keystone-k2g: Add ti-sci clock provider node
ARM: dts: keystone-k2g: Add ti-sci power domain node
...
Biju Das [Tue, 8 Aug 2017 10:56:33 +0000 (11:56 +0100)]
ARM: dts: r8a7743: Add OPP table for frequency scaling
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- clock-latency = 300 us
Approximate worst-case latency to do clock transition for every
OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since DVS is not supported in RZ/G1 Soc.
Note:This also fixes the below errors seen on kernel logs
[ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
[ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Biju Das [Tue, 8 Aug 2017 10:56:32 +0000 (11:56 +0100)]
ARM: dts: r8a7743: Add APMU node and second CPU core
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Wed, 9 Aug 2017 11:27:39 +0000 (12:27 +0100)]
ARM: shmobile: document iW-RainboW-G22M-SM SODIMM System on Module
Document the iW-RainboW-G22M-SM SODIMM System on Module device tree
bindings. It is just a placeholder for the time being, the actual
implementation is not available yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Arnd Bergmann [Wed, 16 Aug 2017 21:32:28 +0000 (23:32 +0200)]
Merge tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Pull "Qualcomm Device Tree Changes for v4.14" from Andy Gross:
* Fixup XO, timer nodes, and pinctrl on IPQ4019
* Add IPQ4019 RNG and wifi blocks
* Update MSM8974 coresight node
* Add IPQ8074 bindings
* tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: add and enable both wifi blocks on the IPQ4019
ARM: dts: qcom-msm8974: dts: Update coresight replicator
ARM: dts: qcom: add pseudo random number generator on the IPQ4019
ARM: dts: ipq4019: Move xo and timer nodes to SoC dtsi
ARM: dts: ipq4019: Fix pinctrl node name
dt-bindings: qcom: Add IPQ8074 bindings
Arnd Bergmann [Wed, 16 Aug 2017 21:12:39 +0000 (23:12 +0200)]
Merge tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:
* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: add pin control set-up for the SoC
ARM: dts: Add DTS file for D-Link DIR-685
ARM: dts: gemini: Switch to using macros
Arnd Bergmann [Wed, 16 Aug 2017 21:07:06 +0000 (23:07 +0200)]
Merge tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.14" from Heiko Stübner:
Removal of the deprectated num-slots property from all Rockchip dw-mmc
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).
The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)
But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.
[0] https://github.com/OP-TEE/optee_os/pull/1666
* tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
ARM: dts: rockchip: fix property-ordering in rv1108 mmc nodes
ARM: dts: rockchip: enable sdmmc for rv1108 evb
ARM: dts: rockchip: add efuse device node for rk3228
ARM: dts: rockchip: add gpio power-key for rk3229-evb
ARM: dts: rockchip: enable tsadc for rk3229-evb
ARM: dts: rockchip: enable eMMC for rk3229-evb
ARM: dts: rockchip: enable io-domain for rk3229-evb
ARM: dts: rockchip: add cpu-supply property for cpu node of rk3229-evb
ARM: dts: rockchip: add regulator nodes for rk3229-evb
ARM: dts: rockchip: add sdmmc and sdio nodes for rk3228 SoC
ARM: dts: rockchip: fix compatible string for eMMC node of rk3228 SoC
ARM: dts: rockchip: add cpu enable method for rk3228 SoC
ARM: dts: rockchip: remove num-slots from all platforms
ARM: dts: rockchip: Add io-domain node for rk3228
ARM: dts: rockchip: add basic dtsi file for RK3229 SoC
ARM: dts: rockchip: enable adc key for rk3288-evb
ARM: dts: rockchip: enable saradc for rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-fennec
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-tinker
...
Arnd Bergmann [Wed, 16 Aug 2017 21:05:39 +0000 (23:05 +0200)]
Merge tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
Changes of note:
* Add pin controller support to the RZ/G1M (r8a7743) SoC and
RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.
* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
is availabe in v4.13-rc1.
* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
controller support noted above.
* Use R-Car Gen 2 fallback binding for vin nodes
This makes binding use consistent across R-Car Gen 2 SoCs.
It does not have any run-time effect
* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs
Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
bringup needs to copy a jump stub to on-SoC SRAM. Currently it uses a
hardcoded address pointing to ICRAM1."
* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs
Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
blocks of SRAM, which can be used for several purposes. One such purpose
is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
and koelsch board.
This is part of a tree-wide cleanup by Javier Martinez Canillas
* tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (38 commits)
ARM: dts: iwg20m: Correct indentation of mmcif0 properties
ARM: dts: rskrza1: Add LED0 pin support
ARM: dts: rskrza1: Add SDHI1 pin group
ARM: dts: rskrza1: Add Ethernet pin group
ARM: dts: rskrza1: Add SCIF2 pin group
ARM: dts: genmai: Add ethernet pin group
ARM: dts: genmai: Add user led device nodes
ARM: dts: genmai: Add RIIC2 pin group
ARM: dts: genmai: Add SCIF2 pin group
ARM: dts: r7s72100: Add pin controller node
ARM: dts: iwg20m: Add MMCIF0 support
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7743: Add MMCIF0 support
ARM: dts: r8a7794: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7793: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7792: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7791: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7790: Reserve SRAM for the SMP jump stub
...
Arnd Bergmann [Wed, 16 Aug 2017 21:04:23 +0000 (23:04 +0200)]
Merge tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:
* Document R-Car D3 (r8a77995) SoC and Draak board
* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs
Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
piece of SRAM for the jump stub +for secondary CPU bringup and CPU
hotplug. +This memory is reserved by adding a child node to a
"mmio-sram" node..."
* Add a VSP channel index to DU vsps
Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
bindings don't support specifying that kind of SoC integration scheme.
Extend them with a VSP channel index."
* Add R-Car M3-W (r8a7796) HDMI TX DT bindings
This is compatible with existing R-Car H3 (r8a7795) support
* tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Document Renesas Draak board DT bindings
ARM: shmobile: Document R-Car D3 SoC DT bindings
dt-bindings: display: rcar-du: Add a VSP channel index to the vsps DT property
dt-bindings: sram: Document renesas,smp-sram
dt-bindings: display: renesas: Add R-Car M3-W HDMI TX DT bindings
Arnd Bergmann [Wed, 16 Aug 2017 21:00:53 +0000 (23:00 +0200)]
Merge tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.14, round 1" from Alexandre Torgue:
Highlights:
----------
-Add DMA support on STM32F746
-Add DMA support on STM32H743
-Add DAC support on STM32H743
-Add DAC support on STM32F429
-Add ADC support on STM32H743
-Enable ADC on stm32h743i-eval board
-Add CEC support on STM32F7xx MCUs
-Enable CEC on stm32f769-disco board
-Remove rdinit from stm32f4 boards
* tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add DMA support for STM32H743 SoC
ARM: dts: stm32: Add DMA support for STM32F746 SoC
ARM: dts: stm32: enable ADC on stm32h743i-eval board
ARM: dts: stm32: add ADC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32f429
ARM: dts: stm32: enable CEC for stm32f769 discovery
ARM: dts: stm32: add CEC for stm32f7 family
ARM: dts: stm32: reorder stm32h743 nodes
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429-disco
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429i-eval
ARM: dts: stm32: Remove rdinit from bootargs on stm32f469-disco
Arnd Bergmann [Wed, 16 Aug 2017 20:54:36 +0000 (22:54 +0200)]
Merge tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.13" from Krzysztof Kozłowski:
Remove deprecated and unneeded properties from Exynos boards.
* tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove num-slots from exynos platforms
ARM: dts: exynos: Remove the OF graph from DSI node
ARM: dts: dra71-evm: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra72-evm: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am572x-idk: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am571x-idk: Add pinmux configuration for MMC
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: dra7-evm: Add pinmux configuration for MMC
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
projects / linux.git / log