mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
Now that most of the raw NAND API is consistent and has almost all its
helpers and hooks using a single nand_chip object instead of an mtd_info
one (or both), let's do the same cleanup in the raw NAND vendors
drivers.
Apply this change to the Toshiba driver so that the internal helper to
retrieve the ECC status does only take a nand_chip object.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Boris Brezillon [Tue, 4 Sep 2018 14:23:28 +0000 (16:23 +0200)]
mtd: rawnand: Allow selection of ECC byte ordering at runtime
Currently, the selection of ECC byte ordering for software hamming is
done at compilation time, which doesn't make sense when ECC byte
calculation is done in hardware and byte ordering is forced by the
hardware engine.
In this case, only the correction is done in software and we want to
force the byte-ordering no matter the value of CONFIG_MTD_NAND_ECC_SMC.
This is typically the case for the FSMC (Smart Media ordering), TMIO and
TXX9NDFMC (regular byte ordering) blocks.
For all other use cases (pure software implementation, SM FTL and
nandecctest), we keep selecting the byte ordering based on the
CONFIG_MTD_NAND_ECC_SMC value. It might not be ideal for SM FTL (I'd
expect Smart Media ordering to be employed by the Smart Media FTL), but
this option doesn't seem to be enabled in the existing _defconfig, so
I can't tell setting sm_order to true is the right choice.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd: rawnand: sh_flctl: Use proper enum for flctl_dma_fifo0_transfer
Clang warns when one enumerated type is converted implicitly to another:
drivers/mtd/nand/raw/sh_flctl.c:483:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/mtd/nand/raw/sh_flctl.c:542:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
mtd: rawnand: ams-delta: Set port direction when needed
In its current shape, the driver sets data port direction before each
byte read/write operation, even during multi-byte transfers. Improve
performance of the driver by setting the port direction only when
needed.
This optimisation will become particularly important as soon as
planned conversion of the driver to GPIO API for data I/O will be
implemented.
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a driver private structure and allocate it on device probe.
Use it for storing nand_chip structure, GPIO descriptors prevoiusly
stored in static variables as well as io_base pointer previously passed
as nand controller data or platform driver data. Subsequent patches
may populate the structure with more members as needed.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now as Amstrad Delta board - the only user of this driver - provides
GPIO lookup tables, switch from GPIO numbers to GPIO descriptors and
use the table to locate required GPIO pins.
Declare static variables for storing GPIO descriptors and replace
gpio_ function calls with their gpiod_ equivalents.
Pin naming used by the driver should be followed while respective GPIO
lookup table is initialized by a board init code.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value") Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd: rawnand: ESMT: retrieve ECC requirements from 5th id byte
This patch enables support to read the ECC level from the NAND flash
using ESMT SLC NAND ID byte 5 information as documented e.g. in the
following data sheet:
Boris Brezillon [Thu, 6 Sep 2018 22:38:42 +0000 (00:38 +0200)]
mtd: rawnand: Move function prototypes after struct declarations
Move nand_scan[_with_ids]() and nand_wait_ready() at the end of the
file where all function prototype lies. This will also allow us to get
rid of the nand_flash_dev forward declaration.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 22:38:41 +0000 (00:38 +0200)]
mtd: rawnand: Deprecate ->chip_delay
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 22:38:39 +0000 (00:38 +0200)]
mtd: rawnand: Deprecate ->erase()
The ->erase() hook have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should have
been an MTD driver (docg4), or the driver uses a specific path for the
ERASE operation (denali), instead of implementing it generically.
In any case, we should discourage people from overloading this method
and encourage them to implement ->exec_op() instead.
Move the ->erase() hook to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should
have been an MTD driver (docg4), or it was not properly implementing
the OOB read/write request or had a weird layout where BBM are trashed.
In any case, we should discourage people from overloading those
methods and encourage them to fix their driver instead.
Move the ->block_{bad,markbad}() hooks to the nand_legacy struct to
make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 22:38:34 +0000 (00:38 +0200)]
mtd: rawnand: Create a legacy struct and move ->IO_ADDR_{R, W} there
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Sat, 4 Aug 2018 20:59:23 +0000 (22:59 +0200)]
mtd: rawnand: Do not treat !maxchips specially in nand_scan_with_ids()
The only reason we were skipping nand_scan_ident() when maxchips == 0
was to make the docg4 to work. Now that this driver is gone we can
remove this special case and return an error when maxchips is 0.
Boris Brezillon [Sat, 4 Aug 2018 20:59:20 +0000 (22:59 +0200)]
mtd: rawnand: Remove docg4
The diskonchip G4 driver does not fit very well in the raw/parallel
NAND framework simply because such chips have an internal controller
translating DoC-specific commands into NAND ones.
Keeping such a driver in the raw NAND framework is a real burden for
NAND maintainers.
Not to mention that some parts of this driver are a bit worrisome:
- writes are done by subpages, even though we're interfacing with an MLC
chip which are known to not support subpage writes very well (it might
be that the FTL handles the complexity for us though)
- some part of the code are simply ignoring return codes of function that
can fail in a few occasions
- there's a hack to support OOB writes when no data is provided. This
operation is not supported by the chip and should have been rejected,
and nandwrite and other userspace tools should have been patched to
deal with such devices
- the driver is apparently broken when ignore_badblocks module param
is not set to 1 and nobody noticed that (don't know since when this
is the case, but it's not a recent change)
http://lists.infradead.org/pipermail/linux-mtd/2018-July/082472.html
Add to that the fact that we already have a docg3 driver in
drivers/mtd/devices/docg3.c and, looking at the code (and regs), it
seems docg3 and docg4 have a lot in common (even the author of this
driver seemed to have realized that interfacing with the raw NAND
framework might have been a bad idea
http://lists.infradead.org/pipermail/linux-mtd/2012-January/039517.html).
For all these reasons, I'm proposing to remove this driver. If anyone
ever wants to add support for this chip back, I'd suggest extending
the docg3 driver instead of adding a completely new driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Cc: Mike Dunn <mikedunn@newsguy.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Sergey Larin <cerg2010cerg2010@mail.ru> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd: rawnand: marvell: support 8b/512B strength for 2kiB pages layout
Add support for the layout used by 2kiB page NAND chips requesting at
least 8-bit of correction per 512 bytes. This layout requires a bit of
handling as:
1/ It can only fit if the NAND chip has at least 128 OOB bytes.
2/ The Bad Block Markers are located in the middle of the data bytes
and shall not be used.
3/ It has been experimentally observed that, for certain layouts, the ECC
engine tries to correct data while it should not because the errors
are uncorrectable. While this is harmless for truly bad pages, it
creates bitflips in empty pages. To avoid such scenario that
augments artificially the number of bitflips we re-read in raw mode
the entire page instead of just the ECC bytes. This is done only
for this layout to avoid an unneeded penalty with other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:35 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object nand_erase_nand()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_erase_nand() helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:34 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to all nand_xxx_bbt() helpers
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_xxx_bbt() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:33 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->setup_data_interface()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_data_interface() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:32 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->setup_read_retry()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_read_retry() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:31 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->{get, set}_features()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->{get,set}_features() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:30 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->erase()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->erase() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:29 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->waitfunc()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->waitfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:28 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->cmdfunc()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmdfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:27 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->dev_ready()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:26 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->cmd_ctrl()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:25 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->block_xxx() hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->block_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:24 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->select_chip()
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:23 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->write_xxx() hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:22 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:21 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to ecc->write_xxx() hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:20 +0000 (14:05 +0200)]
mtd: rawnand: Pass a nand_chip object to ecc->read_xxx() hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Thu, 6 Sep 2018 12:05:13 +0000 (14:05 +0200)]
mtd: rawnand: plat_nand: Pass a nand_chip object to all platform_nand_ctrl hooks
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Krzysztof Halasa <khalasa@piap.pl> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd: rawnand: atmel: use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
mtd: rawnand: jz4780: use struct_size() in devm_kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Masahiro Yamada [Mon, 20 Aug 2018 03:26:36 +0000 (12:26 +0900)]
mtd: rawnand: denali: use SPDX-License-Identifier and fix license mismatch
Use SPDX-License-Identifier instead of the license boilerplates.
This conversion makes it easier for us to scan the license, then
I notice license mismatch problems.
The license blocks in denali* indicate GPL-2.0 "only", while the
MODULE_LICENSE in denali.c and denali_dt.c is GPL-2.0 "or later"
as explained in include/linux/module.h as follows:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
I fixed the MODULE_LICENSE tags, assuming the license blocks are
the authors' intention.
Also, add missing MODULE_DESCRIPTION/AUTHOR to denali.c
While I am touching the license things, I added my credit to denali.c
because this driver was largely re-written by me in 2017.
Kurt Kanzenbach [Mon, 13 Aug 2018 07:18:46 +0000 (09:18 +0200)]
mtd: rawnand: fsl_ifc: fixup SRAM init for newer ctrl versions
Newer versions of the IFC controller use a different method of initializing the
internal SRAM: Instead of reading from flash, a bit in the NAND configuration
register has to be set in order to trigger the self-initializing process.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Kurt Kanzenbach [Mon, 13 Aug 2018 07:18:45 +0000 (09:18 +0200)]
mtd: rawnand: fsl_ifc: check result of SRAM initialization
The SRAM initialization might fail. If that happens further NAND operations
won't be successful. Therefore, the chip init routine should fail if the SRAM
initialization didn't work.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Miquel Raynal [Sun, 5 Aug 2018 14:52:57 +0000 (16:52 +0200)]
Documentation: mtd: remove stale pxa3xx NAND controller documentation
It is preferred to have the documentation about the drivers directly
embedded in the driver itself. Remove this file now that the most
important information from this file have been re-written in
marvell_nand.c.
Miquel Raynal [Sun, 5 Aug 2018 14:52:56 +0000 (16:52 +0200)]
mtd: rawnand: marvell: document a bit more the driver
A stale document about the old pxa3cc_nand.c driver is available in
Documentation/mtd/nand/. Rewrite the parts that explain the IP itself
and some non-trivial choices made in the driver directly in
marvell_nand.c to then be able to remove this file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
mtd: rawnand: toshiba: Add support for Toshiba Memory BENAND (Built-in ECC NAND)
This patch is a patch to support TOSHIBA MEMORY CORPORATION BENAND
memory devices. Check the status of the built-in ECC with the Read
Status command without using the vendor specific command. The Read
Status command only knows whether there was bitflips above the
threshold and can not get accurate bitflips. For now, I set
max_bitflips mtd->bitflip_threshold.
mtd: rawnand: marvell: use regmap_update_bits() for syscon access
The marvell_nfc_init() function fiddles with some bits of a system
controller on Armada 7K/8K. However, it does a read/modify/write
sequence on GENCONF_CLK_GATING_CTRL and GENCONF_ND_CLK_CTRL, which
isn't safe from a concurrency point of view, as the regmap lock isn't
taken accross the read/modify/write sequence. To solve this issue, use
regmap_update_bits().
While at it, since the "reg" variable is no longer needed for the
read/modify/write sequences, get rid of it for the regmap_write() to
GENCONF_SOC_DEVICE_MUX, and directly pass the value to be written as
argument.
Boris Brezillon [Fri, 27 Jul 2018 21:05:42 +0000 (23:05 +0200)]
mtd: rawnand: Get rid of the ->read_word() hook
Commit c120e75e0e7d ("mtd: nand: use read_oob() instead of cmdfunc()
for bad block check") removed this only user of the ->read_word()
method but kept the hook in place. Remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Fri, 27 Jul 2018 07:44:18 +0000 (09:44 +0200)]
mtd: rawnand: Add the nand_wait_rdy_op() helper and use it
In order to make sure we use ->exec_op() to wait for chip readiness
when it's available we provide an helper that does the selection
between ->exec_op(), udelay(chip->chip_delay) and nand_wait_ready()
based on what's implemented by the controller driver.
We then use it in nand_wait_readrdy().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Boris Brezillon [Fri, 27 Jul 2018 07:44:17 +0000 (09:44 +0200)]
mtd: rawnand: Add the nand_wait_readrdy() helper and use it
The logic to wait for chip readiness after a page read has been
duplicated in nand_do_read_ops() and nand_do_read_oob(). Provide an
helper that does the right thing and call it where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to
new panel bindings. The platforms were moved from legacy
framebuffers to DRM and some development board panels hadn't yet
been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing
some register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged
this window (AM6)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: Enable TI's AM6 SoC platform
ARM: defconfig: Update the ARM Versatile defconfig
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Speculation:
- Make the microcode check more robust
- Make the L1TF memory limit depend on the internal cache physical
address space and not on the CPUID advertised physical address
space, which might be significantly smaller. This avoids disabling
L1TF on machines which utilize the full physical address space.
- Fix the GDT mapping for EFI calls on 32bit PTI
- Fix the MCE nospec implementation to prevent #GP
Fixes and robustness:
- Use the proper operand order for LSL in the VDSO
- Prevent NMI uaccess race against CR3 switching
- Add a lockdep check to verify that text_mutex is held in
text_poke() functions
- Repair the fallout of giving native_restore_fl() a prototype
- Prevent kernel memory dumps based on usermode RIP
- Wipe KASAN shadow stack before rewinding the stack to prevent false
positives
- Move the AMS GOTO enforcement to the actual build stage to allow
user API header extraction without a compiler
- Fix a section mismatch introduced by the on demand VDSO mapping
change
Miscellaneous:
- Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Fix section mismatch warning/error
x86/vdso: Fix lsl operand order
x86/mce: Fix set_mce_nospec() to avoid #GP fault
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
x86/nmi: Fix NMI uaccess race against CR3 switching
x86: Allow generating user-space headers without a compiler
x86/dumpstack: Don't dump kernel memory based on usermode RIP
x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
x86/irqflags: Mark native_restore_fl extern inline
x86/build: Remove jump label quirk for GCC older than 4.5.2
x86/Kconfig: Fix trivial typo
x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
x86/spectre: Add missing family 6 check to microcode check
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A small set of updates for core code:
- Prevent tracing in functions which are called from trace patching
via stop_machine() to prevent executing half patched function trace
entries.
- Remove old GCC workarounds
- Remove pointless includes of notifier.h"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Remove workaround for unreachable warnings from old GCC
notifier: Remove notifier header file wherever not used
watchdog: Mark watchdog touch functions as notrace
Randy Dunlap [Sun, 2 Sep 2018 04:01:28 +0000 (21:01 -0700)]
x86/pti: Fix section mismatch warning/error
Fix the section mismatch warning in arch/x86/mm/pti.c:
WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.
Fixes: 85900ea51577 ("x86/pti: Map the vsyscall page if needed") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org
Olof Johansson [Sun, 2 Sep 2018 01:22:19 +0000 (18:22 -0700)]
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Samuel Neves [Sat, 1 Sep 2018 20:14:52 +0000 (21:14 +0100)]
x86/vdso: Fix lsl operand order
In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.
Fixes: a582c540ac1b ("x86/vdso: Use RDPID in preference to LSL when available") Signed-off-by: Samuel Neves <sneves@dei.uc.pt> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two small fixes, one for the x86 Stoney SoC to get a more accurate clk
frequency and the other to fix a bad allocation in the Nuvoton NPCM7XX
driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: x86: Set default parent to 48Mhz
clk: npcm7xx: fix memory allocation
LuckTony [Fri, 31 Aug 2018 16:55:06 +0000 (09:55 -0700)]
x86/mce: Fix set_mce_nospec() to avoid #GP fault
The trick with flipping bit 63 to avoid loading the address of the 1:1
mapping of the poisoned page while the 1:1 map is updated used to work when
unmapping the page. But it falls down horribly when attempting to directly
set the page as uncacheable.
The problem is that when the cache mode is changed to uncachable, the pages
needs to be flushed from the cache first. But the decoy address is
non-canonical due to bit 63 flipped, and the CLFLUSH instruction throws a
#GP fault.
Add code to change_page_attr_set_clr() to fix the address before calling
flush.
Fixes: 284ce4011ba6 ("x86/memory_failure: Introduce {set, clear}_mce_nospec()") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Anvin <hpa@zytor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Jiang <dave.jiang@intel.com> Link: https://lkml.kernel.org/r/20180831165506.GA9605@agluck-desk
Linus Torvalds [Fri, 31 Aug 2018 16:20:30 +0000 (09:20 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A few arm64 fixes came in this week, specifically fixing some nasty
truncation of return values from firmware calls and resolving a
VM_BUG_ON due to accessing uninitialised struct pages corresponding to
NOMAP pages.
Summary:
- Fix typos in SVE documentation
- Fix type-checking and implicit truncation for SMCCC calls
- Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP
regions"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
arm/arm64: smccc-1.1: Handle function result as parameters
arm/arm64: smccc-1.1: Make return values unsigned long
Documentation/arm64/sve: Couple of improvements and typos
Joerg Roedel [Fri, 31 Aug 2018 08:05:38 +0000 (10:05 +0200)]
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
When PTI is enabled on x86-32 the kernel uses the GDT mapped in the fixmap
for the simple reason that this address is also mapped for user-space.
The efi_call_phys_prolog()/efi_call_phys_epilog() wrappers change the GDT
to call EFI runtime services and switch back to the kernel GDT when they
return. But the switch-back uses the writable GDT, not the fixmap GDT.
When that happened and and the CPU returns to user-space it switches to the
user %cr3 and tries to restore user segment registers. This fails because
the writable GDT is not mapped in the user page-table, and without a GDT
the fault handlers also can't be launched. The result is a triple fault and
reboot of the machine.
Fix that by restoring the GDT back to the fixmap GDT which is also mapped
in the user page-table.
Linus Torvalds [Fri, 31 Aug 2018 15:45:16 +0000 (08:45 -0700)]
Merge tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- minor cleanup avoiding a warning when building with new gcc
- a patch to add a new sysfs node for Xen frontend/backend drivers to
make it easier to obtain the state of a pv device
- two fixes for 32-bit pv-guests to avoid intermediate L1TF vulnerable
PTEs
* tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: remove redundant variable save_pud
xen: export device state to sysfs
x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear
x86/xen: don't write ptes directly in 32-bit PV guests
Linus Torvalds [Fri, 31 Aug 2018 15:38:53 +0000 (08:38 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- regression fixes for i801 and designware
- better API and leak fix for releasing DMA safe buffers
- better greppable strings for the bitbang algorithm
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix leak when using DMA bounce buffer
i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
i2c: refactor function to release a DMA safe buffer
i2c: algos: bit: make the error messages grepable
i2c: designware: Re-init controllers with pm_disabled set on resume
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Andy Lutomirski [Wed, 29 Aug 2018 15:47:18 +0000 (08:47 -0700)]
x86/nmi: Fix NMI uaccess race against CR3 switching
A NMI can hit in the middle of context switching or in the middle of
switch_mm_irqs_off(). In either case, CR3 might not match current->mm,
which could cause copy_from_user_nmi() and friends to read the wrong
memory.
Fix it by adding a new nmi_uaccess_okay() helper and checking it in
copy_from_user_nmi() and in __copy_from_user_nmi()'s callers.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Rik van Riel <riel@surriel.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Jann Horn <jannh@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/dd956eba16646fd0b15c3c0741269dfd84452dac.1535557289.git.luto@kernel.org
Ben Hutchings [Wed, 29 Aug 2018 19:43:17 +0000 (20:43 +0100)]
x86: Allow generating user-space headers without a compiler
When bootstrapping an architecture, it's usual to generate the kernel's
user-space headers (make headers_install) before building a compiler. Move
the compiler check (for asm goto support) to the archprepare target so that
it is only done when building code for the target.
Fixes: e501ce957a78 ("x86: Force asm-goto") Reported-by: Helmut Grohne <helmutg@debian.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180829194317.GA4765@decadent.org.uk
Jann Horn [Tue, 28 Aug 2018 15:49:01 +0000 (17:49 +0200)]
x86/dumpstack: Don't dump kernel memory based on usermode RIP
show_opcodes() is used both for dumping kernel instructions and for dumping
user instructions. If userspace causes #PF by jumping to a kernel address,
show_opcodes() can be reached with regs->ip controlled by the user,
pointing to kernel code. Make sure that userspace can't trick us into
dumping kernel memory into dmesg.
Fixes: 7cccf0725cf7 ("x86/dumpstack: Add a show_ip() function") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: security@kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180828154901.112726-1-jannh@google.com
Rob Herring [Tue, 28 Aug 2018 20:10:48 +0000 (15:10 -0500)]
of: Add device_type access helper functions
In preparation to remove direct access to device_node.type, add
of_node_is_type() and of_node_get_device_type() helpers to check and
retrieve the device type.
Cc: Frank Rowand <frowand.list@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
Mukesh Ojha [Tue, 28 Aug 2018 06:54:54 +0000 (12:24 +0530)]
cpu/hotplug: Remove skip_onerr field from cpuhp_step structure
When notifiers were there, `skip_onerr` was used to avoid calling
particular step startup/teardown callbacks in the CPU up/down rollback
path, which made the hotplug asymmetric.
As notifiers are gone now after the full state machine conversion, the
`skip_onerr` field is no longer required.
James Morse [Thu, 30 Aug 2018 15:05:32 +0000 (16:05 +0100)]
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
Commit 6d526ee26ccd ("arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA")
only enabled HOLES_IN_ZONE for NUMA systems because the NUMA code was
choking on the missing zone for nomap pages. This problem doesn't just
apply to NUMA systems.
If the architecture doesn't set HAVE_ARCH_PFN_VALID, pfn_valid() will
return true if the pfn is part of a valid sparsemem section.
When working with multiple pages, the mm code uses pfn_valid_within()
to test each page it uses within the sparsemem section is valid. On
most systems memory comes in MAX_ORDER_NR_PAGES chunks which all
have valid/initialised struct pages. In this case pfn_valid_within()
is optimised out.
Systems where this isn't true (e.g. due to nomap) should set
HOLES_IN_ZONE and provide HAVE_ARCH_PFN_VALID so that mm tests each
page as it works with it.
Currently non-NUMA arm64 systems can't enable HOLES_IN_ZONE, leading to
a VM_BUG_ON():
Linus Torvalds [Fri, 31 Aug 2018 04:18:05 +0000 (21:18 -0700)]
Merge tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull:
- Mediatek has a bunch of fixes to their RDMA and Overlay engines.
- i915 has some Cannonlake/Geminilake watermark workarounds, LSPCON
fix, HDCP free fix, audio fix and a ppgtt reference counting fix.
- amdgpu has some SRIOV, Kasan, memory leaks and other misc fixes"
* tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm: (35 commits)
drm/i915/audio: Hook up component bindings even if displays are disabled
drm/i915: Increase LSPCON timeout
drm/i915: Stop holding a ref to the ppgtt from each vma
drm/i915: Free write_buf that we allocated with kzalloc.
drm/i915: Fix glk/cnl display w/a #1175
drm/amdgpu: Need to set moved to true when evict bo
drm/amdgpu: Remove duplicated power source update
drm/amd/display: Fix memory leak caused by missed dc_sink_release
drm/amdgpu: fix holding mn_lock while allocating memory
drm/amdgpu: Power on uvd block when hw_fini
drm/amdgpu: Update power state at the end of smu hw_init.
drm/amdgpu: Fix vce initialize failed on Kaveri/Mullins
drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode
drm/amdgpu: Adjust the VM size based on system memory size v2
drm/mediatek: fix connection from RDMA2 to DSI1
drm/mediatek: update some variable name from ovl to comp
drm/mediatek: use layer_nr function to get layer number to init plane
drm/mediatek: add function to return RDMA layer number
drm/mediatek: add function to return OVL layer number
drm/mediatek: add function to get layer number for component
...
Linus Torvalds [Fri, 31 Aug 2018 01:02:02 +0000 (18:02 -0700)]
Merge tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address a corner case in the menu cpuidle governor and fix error
handling in the PM core's generic clock management code.
Specifics:
- Make the menu cpuidle governor avoid stopping the scheduler tick if
the predicted idle duration exceeds the tick period length, but the
selected idle state is shallow and deeper idle states with high
target residencies are available (Rafael Wysocki).
- Make the PM core's generic clock management code use a proper data
type for one variable to make error handling work (Dan Carpenter)"
* tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: menu: Retain tick when shallow state is selected
PM / clk: signedness bug in of_pm_clk_add_clks()