Madalin Bucur [Wed, 22 Jan 2020 14:15:14 +0000 (16:15 +0200)]
net: fsl/fman: rename IF_MODE_XGMII to IF_MODE_10G
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses a HW erratum on some QorIQ DPAA devices.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
When the issue was present, one could see such errors
during boot:
mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER]
bit may be falsely set when reading internal PCS registers.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Wed, 22 Jan 2020 09:43:38 +0000 (01:43 -0800)]
qlcnic: Fix CPU soft lockup while collecting firmware dump
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com> Tested-by: Yonggen Xu <Yonggen.Xu@dell.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 23 Jan 2020 19:37:19 +0000 (11:37 -0800)]
Merge tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"Primarily bugfixes, mostly around handling index wrap-around
correctly.
A couple of doc fixes and adding missing APIs.
I had an oops live on stage at linux.conf.au this year, and it turned
out to be a bug in xas_find() which I can't prove isn't triggerable in
the current codebase. Then in looking for the bug, I spotted two more
bugs.
The bots have had a few days to chew on this with no problems
reported, and it passes the test-suite (which now has more tests to
make sure these problems don't come back)"
* tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax:
XArray: Add xa_for_each_range
XArray: Fix xas_find returning too many entries
XArray: Fix xa_find_after with multi-index entries
XArray: Fix infinite loop with entry at ULONG_MAX
XArray: Add wrappers for nested spinlocks
XArray: Improve documentation of search marks
XArray: Fix xas_pause at ULONG_MAX
Linus Torvalds [Thu, 23 Jan 2020 19:23:37 +0000 (11:23 -0800)]
Merge tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for
multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and
calling trace_set_default_clock()
- A fix to a bug found with the double perf_event linking patch"
* tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobe: Fix to make trace_uprobe_filter alignment safe
tracing: Do not set trace clock if tracefs lockdown is in effect
tracing: Fix histogram code when expression has same var as value
tracing: trigger: Replace unneeded RCU-list traversals
tracing/uprobe: Fix double perf_event linking on multiprobe uprobe
tracing: xen: Ordered comparison of function pointers
Linus Torvalds [Thu, 23 Jan 2020 19:10:21 +0000 (11:10 -0800)]
Merge tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Prevent the kernel from crashing during resume from hibernation if
free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko)"
* tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: fix crashes with init_on_free=1
Linus Torvalds [Wed, 22 Jan 2020 20:37:25 +0000 (12:37 -0800)]
readdir: make user_access_begin() use the real access range
In commit 9f79b78ef744 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I changed filldir to not do individual __put_user()
accesses, but instead use unsafe_put_user() surrounded by the proper
user_access_begin/end() pair.
That make them enormously faster on modern x86, where the STAC/CLAC
games make individual user accesses fairly heavy-weight.
However, the user_access_begin() range was not really the exact right
one, since filldir() has the unfortunate problem that it needs to not
only fill out the new directory entry, it also needs to fix up the
previous one to contain the proper file offset.
It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the
file offset of the directory entry itself - it's the offset of the next
one. So we end up backfilling the offset in the previous entry as we
walk along.
But since x86 didn't really care about the exact range, and used to be
the only architecture that did anything fancy in user_access_begin() to
begin with, the filldir[64]() changes did something lazy, and even
commented on it:
/*
* Note! This range-checks 'previous' (which may be NULL).
* The real range was checked in getdents
*/
if (!user_access_begin(dirent, sizeof(*dirent)))
goto efault;
and it all worked fine.
But now 32-bit ppc is starting to also implement user_access_begin(),
and the fact that we faked the range to only be the (possibly not even
valid) previous directory entry becomes a problem, because ppc32 will
actually be using the range that is passed in for more than just "check
that it's user space".
This is a complete rewrite of Christophe's original patch.
By saving off the record length of the previous entry instead of a
pointer to it in the filldir data structures, we can simplify the range
check and the writing of the previous entry d_off field. No need for
any conditionals in the user accesses themselves, although we retain the
conditional EINTR checking for the "was this the first directory entry"
signal handling latency logic.
Linus Torvalds [Thu, 23 Jan 2020 18:05:05 +0000 (10:05 -0800)]
readdir: be more conservative with directory entry names
Commit 8a23eb804ca4 ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Kristian Evensen [Thu, 23 Jan 2020 12:20:18 +0000 (13:20 +0100)]
fou: Fix IPv6 netlink policy
When submitting v2 of "fou: Support binding FoU socket" (1713cb37bf67),
I accidentally sent the wrong version of the patch and one fix was
missing. In the initial version of the patch, as well as the version 2
that I submitted, I incorrectly used ".type" for the two V6-attributes.
The correct is to use ".len".
Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 1713cb37bf67 ("fou: Support binding FoU socket") Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Jan 2020 13:30:20 +0000 (14:30 +0100)]
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jan 2020 17:07:35 +0000 (09:07 -0800)]
tun: add mutex_unlock() call and napi.skb clearing in tun_get_user()
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Petar Penkov <ppenkov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 22 Jan 2020 18:09:52 +0000 (20:09 +0200)]
mlxsw: spectrum_acl: Fix use-after-free during reload
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200dead000000000100dead000000000122ffff888236403500
[ 123.734646] raw: 0000000000000000000000000010001000000001ffffffff0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc/mm/hash: Fix sharing context ids between kernel & userspace
Commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in
the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT.
The result is that the context id used for the vmemmap and the lowest
context id handed out to userspace are the same. The context id is
essentially the process identifier as far as the first stage of the
MMU translation is concerned.
This can result in multiple SLB entries with the same VSID (Virtual
Segment ID), accessible to the kernel and some random userspace
process that happens to get the overlapping id, which is not expected
eg:
Even though the user process and the kernel use the same VSID, the
permissions in the hash page table prevent the user process from
reading or writing to any kernel mappings.
It can also lead to SLB entries with different base page size
encodings (LLP), eg:
This happens with 256MB segments and 64K pages, as the duplicate VSID
is hit with the first vmemmap segment and the first user segment, and
older 32-bit userspace maps things in the first user segment.
On other CPUs a machine check is not seen. Instead the userspace
process can get stuck continuously faulting, with the fault never
properly serviced, due to the kernel not understanding that there is
already a HPTE for the address but with inaccessible permissions.
On machines with 1T segments we've not seen the bug hit other than by
deliberately exercising it. That seems to be just a matter of luck
though, due to the typical layout of the user virtual address space
and the ranges of vmemmap that are typically populated.
To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest
context given to userspace doesn't overlap with the VMEMMAP context,
or with the context for INVALID_REGION_ID.
Fixes: 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range") Cc: stable@vger.kernel.org # v5.2+ Reported-by: Christian Marillat <marillat@debian.org> Reported-by: Romain Dolbeau <romain@dolbeau.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Account for INVALID_REGION_ID, mostly rewrite change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
Hayes Wang [Wed, 22 Jan 2020 08:02:13 +0000 (16:02 +0800)]
r8152: disable DelayPhyPwrChg
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Wed, 22 Jan 2020 08:02:12 +0000 (16:02 +0800)]
r8152: avoid the MCU to clear the lanwake
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pablo Neira <pablo@netfilter.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jan 2020 06:47:29 +0000 (22:47 -0800)]
net: rtnetlink: validate IFLA_MTU attribute in rtnl_create_link()
rtnl_create_link() needs to apply dev->min_mtu and dev->max_mtu
checks that we apply in do_setlink()
Otherwise malicious users can crash the kernel, for example after
an integer overflow :
BUG: KASAN: use-after-free in memset include/linux/string.h:365 [inline]
BUG: KASAN: use-after-free in __alloc_skb+0x37b/0x5e0 net/core/skbuff.c:238
Write of size 32 at addr ffff88819f20b9c0 by task swapper/0/0
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Ellerman [Wed, 22 Jan 2020 04:07:28 +0000 (15:07 +1100)]
airo: Add missing CAP_NET_ADMIN check in AIROOLDIOCTL/SIOCDEVPRIVATE
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Ellerman [Wed, 22 Jan 2020 04:07:27 +0000 (15:07 +1100)]
airo: Fix possible info leak in AIROOLDIOCTL/SIOCDEVPRIVATE
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The optee driver uses specific page table types to verify if a memory
region is normal. These types are not defined in nommu systems. Trying
to compile the driver in these systems results in a build error:
linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’:
linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared
(first use in this function); did you mean ‘PREEMPT_MASK’?
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~
PREEMPT_MASK
linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is
reported only once for each function it appears in
linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared
(first use in this function)
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~~~~~~~
Make the optee driver depend on MMU to fix the compilation issue.
Andrew Lunn [Wed, 22 Jan 2020 19:23:15 +0000 (20:23 +0100)]
MAINTAINERS: Make Russell King designated reviewer of phylib
phylink and phylib are interconnected. It makes sense for phylib and
phy driver patches to be also reviewed by the phylink maintainer.
So add Russell King as a designed reviewer of phylib.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 22 Jan 2020 20:56:19 +0000 (12:56 -0800)]
Merge tag 'leds-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED fixes from Pavel Machek:
"Jacek's fix for an uninitialized gpio label is why I'm requesting this
pull; it fixes regression in debugging output in sysfs. Others are
just bugfixes that should be safe.
Everything has been in -next for while"
* tag 'leds-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lm3532: add pointer to documentation and fix typo
leds: rb532: cleanup whitespace
ledtrig-pattern: fix email address quoting in MODULE_AUTHOR()
led: max77650: add of_match table
leds-as3645a: Drop fwnode reference on ignored node
leds: gpio: Fix uninitialized gpio label for fwnode based probe
Linus Torvalds [Wed, 22 Jan 2020 20:38:10 +0000 (12:38 -0800)]
Merge tag 'hwmon-for-v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- In hwmon core, do not use the hwmon parent device for device managed
memory allocations, since parent device lifetime may not match hwmon
device lifetime.
- Fix discrepancy between read and write values in adt7475 driver.
- Fix alarms and voltage limits in nct7802 driver.
* tag 'hwmon-for-v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (core) Do not use device managed functions for memory allocations
hwmon: (adt7475) Make volt2reg return same reg as reg2volt input
hwmon: (nct7802) Fix non-working alarm on voltages
hwmon: (nct7802) Fix voltage limits to wrong registers
William Dauchy [Tue, 21 Jan 2020 20:49:54 +0000 (21:49 +0100)]
net, ip6_tunnel: fix namespaces move
in the same manner as commit d0f418516022 ("net, ip_tunnel: fix
namespaces move"), fix namespace moving as it was broken since commit 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for
ipv6 this time; there is no reason to keep it for ip6_tunnel.
Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnel") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Williem reported that after commit 0d4a6608f68c ("udp: do rmem bulk
free even if the rx sk queue is empty") the memory allocated by
an almost idle system with many UDP sockets can grow a lot.
For stable kernel keep the solution as simple as possible and revert
the offending commit.
Reported-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 0d4a6608f68c ("udp: do rmem bulk free even if the rx sk queue is empty") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sakari Ailus [Wed, 4 Dec 2019 07:56:42 +0000 (09:56 +0200)]
leds-as3645a: Drop fwnode reference on ignored node
If a node is ignored, do not get a reference to it. Fix the bug by moving
fwnode_handle_get() where a reference to an fwnode is saved for clarity.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Pavel Machek <pavel@ucw.cz>
leds: gpio: Fix uninitialized gpio label for fwnode based probe
When switching to using generic LED name composition mechanism via
devm_led_classdev_register_ext() API the part of code initializing
struct gpio_led's template name property was removed alongside.
It was however overlooked that the property was also passed to
devm_fwnode_get_gpiod_from_child() in place of "label" parameter,
which when set to NULL, results in gpio label being initialized to '?'.
It could be observed in debugfs and failed to properly identify
gpio association with LED consumer.
Fix this shortcoming by updating the GPIO label after the LED is
registered and its final name is known.
Fixes: d7235f5feaa0 ("leds: gpio: Use generic support for composing LED names") Cc: Russell King <linux@armlinux.org.uk> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[fixed comment] Signed-off-by: Pavel Machek <pavel@ucw.cz>
net: Fix packet reordering caused by GRO and listified RX cooperation
Commit 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0df ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL skbs") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Cc: Alexander Lobakin <alobakin@dlink.ru> Cc: Edward Cree <ecree@solarflare.com> Acked-by: Alexander Lobakin <alobakin@dlink.ru> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can, slip: Protect tty->disc_data in write_wakeup and close with RCU
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21b1 ("slip: Fix deadlock in write_wakeup") Fixes: a8e83b17536a ("slcan: Port write_wakeup deadlock fix from slip") Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Tyler Hall <tylerwhall@gmail.com> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Tue, 21 Jan 2020 12:31:47 +0000 (13:31 +0100)]
net, sk_msg: Don't check if sock is locked when tearing down psock
As John Fastabend reports [0], psock state tear-down can happen on receive
path *after* unlocking the socket, if the only other psock user, that is
sockmap or sockhash, releases its psock reference before tcp_bpf_recvmsg
does so:
Remove the lockdep check for socket lock in psock tear-down that got
introduced in 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during
tear down").
Fixes: 7e81a3530206 ("bpf: Sockmap, ensure sock lock held during tear down") Reported-by: syzbot+d73682fcf7fee6982fe3@syzkaller.appspotmail.com Suggested-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Murzin [Mon, 20 Jan 2020 14:07:46 +0000 (15:07 +0100)]
ARM: 8955/1: virt: Relax arch timer version check during early boot
Updates to the Generic Timer architecture allow ID_PFR1.GenTimer to
have values other than 0 or 1 while still preserving backward
compatibility. At the moment, Linux is quite strict in the way it
handles this field at early boot and will not configure arch timer if
it doesn't find the value 1.
Since here use ubfx for arch timer version extraction (hyb-stub build
with -march=armv7-a, so it is safe)
To help backports (even though the code was correct at the time of writing)
Fixes: 8ec58be9f3ff ("ARM: virt: arch_timers: enable access to physical timers") Acked-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
iwlwifi: mvm: don't send the IWL_MVM_RXQ_NSSN_SYNC notif to Rx queues
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831ac12356b695ff054bef641b9e99593:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873
https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831ac ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues") CC: <stable@vger.kernel.org> # 5.3+ Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linus Torvalds [Wed, 22 Jan 2020 16:30:09 +0000 (08:30 -0800)]
Merge tag 'io_uring-5.5-2020-01-22' of git://git.kernel.dk/linux-block
Pull io_uring fix from Jens Axboe:
"This was supposed to have gone in last week, but due to a brain fart
on my part, I forgot that we made this struct addition in the 5.5
cycle. So here it is for 5.5, to prevent having a 32 vs 64-bit
compatability issue with the files_update command"
* tag 'io_uring-5.5-2020-01-22' of git://git.kernel.dk/linux-block:
io_uring: fix compat for IORING_REGISTER_FILES_UPDATE
Masami Hiramatsu [Wed, 22 Jan 2020 03:23:25 +0000 (12:23 +0900)]
tracing/uprobe: Fix to make trace_uprobe_filter alignment safe
Commit 99c9a923e97a ("tracing/uprobe: Fix double perf_event
linking on multiprobe uprobe") moved trace_uprobe_filter on
trace_probe_event. However, since it introduced a flexible
data structure with char array and type casting, the
alignment of trace_uprobe_filter can be broken.
This changes the type of the array to trace_uprobe_filter
data strucure to fix it.
Frederic Barrat [Mon, 13 Jan 2020 13:01:18 +0000 (14:01 +0100)]
powerpc/xive: Discard ESB load value when interrupt is invalid
A load on an ESB page returning all 1's means that the underlying
device has invalidated the access to the PQ state of the interrupt
through mmio. It may happen, for example when querying a PHB interrupt
while the PHB is in an error state.
In that case, we should consider the interrupt to be invalid when
checking its state in the irq_get_irqchip_state() handler.
Fixes: da15c03b047d ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
[clg: wrote a commit log, introduced XIVE_ESB_INVALID ] Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200113130118.27969-1-clg@kaod.org
Jeff Layton [Wed, 3 Apr 2019 17:16:01 +0000 (13:16 -0400)]
ceph: hold extra reference to r_parent over life of request
Currently, we just assume that it will stick around by virtue of the
submitter's reference, but later patches will allow the syscall to
return early and we can't rely on that reference at that point.
While I'm not aware of any reports of it, Xiubo pointed out that this
may fix a use-after-free. If the wait for a reply times out or is
canceled via signal, and then the reply comes in after the syscall
returns, the client can end up trying to access r_parent without a
reference.
Take an extra reference to the inode when setting r_parent and release
it when releasing the request.
Boris Brezillon [Thu, 16 Jan 2020 02:15:54 +0000 (20:15 -0600)]
drm/panfrost: Add the panfrost_gem_mapping concept
With the introduction of per-FD address space, the same BO can be mapped
in different address space if the BO is globally visible (GEM_FLINK)
and opened in different context or if the dmabuf is self-imported. The
current implementation does not take case into account, and attaches the
mapping directly to the panfrost_gem_object.
Let's create a panfrost_gem_mapping struct and allow multiple mappings
per BO.
The mappings are refcounted which helps solve another problem where
mappings were torn down (GEM handle closed by userspace) while GPU
jobs accessing those BOs were still in-flight. Jobs now keep a
reference on the mappings they use.
v2 (robh):
- Minor review comment clean-ups from Steven
- Use list_is_singular helper
- Just WARN if we add a mapping when madvise state is not WILLNEED.
With that, drop the use of object_name_lock.
v3 (robh):
- Revert returning list iterator in panfrost_gem_mapping_get()
Fixes: a5efb4c9a562 ("drm/panfrost: Restructure the GEM object creation") Fixes: 7282f7645d06 ("drm/panfrost: Implement per FD address spaces") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Steven Price <steven.price@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200116021554.15090-1-robh@kernel.org
William Dauchy [Tue, 21 Jan 2020 14:26:24 +0000 (15:26 +0100)]
net, ip_tunnel: fix namespaces move
in the same manner as commit 690afc165bb3 ("net: ip6_gre: fix moving
ip6gre between namespaces"), fix namespace moving as it was broken since
commit 2e15ea390e6f ("ip_gre: Add support to collect tunnel metadata.").
Indeed, the ip6_gre commit removed the local flag for collect_md
condition, so there is no reason to keep it for ip_gre/ip_tunnel.
this patch will fix both ip_tunnel and ip_gre modules.
Fixes: 2e15ea390e6f ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Theodore Dubois [Mon, 20 Jan 2020 22:10:53 +0000 (14:10 -0800)]
tcp: remove redundant assigment to snd_cwnd
Not sure how this got in here. git blame says the second assignment was
added in 3a9a57f6, but that commit also removed the first assignment.
Signed-off-by: Theodore Dubois <tblodt@icloud.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Hughes [Mon, 20 Jan 2020 11:12:40 +0000 (11:12 +0000)]
net: usb: lan78xx: Add .ndo_features_check
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Mon, 20 Jan 2020 10:04:56 +0000 (18:04 +0800)]
tcp_bbr: improve arithmetic division in bbr_update_bw()
do_div() does a 64-by-32 division. Use div64_long() instead of it
if the divisor is long, to avoid truncation to 32-bit.
And as a nice side effect also cleans up the function a bit.
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Eric Dumazet <edumazet@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jouni Hogander [Mon, 20 Jan 2020 07:51:03 +0000 (09:51 +0200)]
net-sysfs: Fix reference count leak
Netdev_register_kobject is calling device_initialize. In case of error
reference taken by device_initialize is not given up.
Drivers are supposed to call free_netdev in case of error. In non-error
case the last reference is given up there and device release sequence
is triggered. In error case this reference is kept and the release
sequence is never started.
Fix this by setting reg_state as NETREG_UNREGISTERED if registering
fails.
This is the rootcause for couple of memory leaks reported by Syzkaller:
v3 -> v4:
Set reg_state to NETREG_UNREGISTERED if registering fails
v2 -> v3:
* Replaced BUG_ON with WARN_ON in free_netdev and netdev_release
v1 -> v2:
* Relying on driver calling free_netdev rather than calling
put_device directly in error path
Reported-by: syzbot+ad8ca40ecd77896d51e2@syzkaller.appspotmail.com Cc: David Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuki Taguchi [Mon, 20 Jan 2020 04:48:37 +0000 (13:48 +0900)]
ipv6: sr: remove SKB_GSO_IPXIP6 on End.D* actions
After LRO/GRO is applied, SRv6 encapsulated packets have
SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after
decapulation procedure.
Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which
creates inconsistent packet state, that is, a normal TCP/IP packets
have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected
fallback to GSO on routing to netdevices that do not support
SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated
packets separated into small packets by GSO because VRF devices do not
support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades
forwarding performance.
This patch removes encapsulation related GSO flags from the skb right
after the End.D* action is applied.
Fixes: d7a669dd2f8b ("ipv6: sr: add helper functions for seg6local") Signed-off-by: Yuki Taguchi <tagyounit@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tvrtko Ursulin [Thu, 16 Jan 2020 13:45:08 +0000 (13:45 +0000)]
drm/i915: Align engine->uabi_class/instance with i915_drm.h
In our ABI we have defined I915_ENGINE_CLASS_INVALID_NONE and
I915_ENGINE_CLASS_INVALID_VIRTUAL as negative values which creates
implicit coupling with type widths used in, also ABI, struct
i915_engine_class_instance.
One place where we export engine->uabi_class
I915_ENGINE_CLASS_INVALID_VIRTUAL is from our our tracepoints. Because the
type of the former is u8 in contrast to u16 defined in the ABI, 254 will
be returned instead of 65534 which userspace would legitimately expect.
Another place is I915_CONTEXT_PARAM_ENGINES.
Therefore we need to align the type used to store engine ABI class and
instance.
v2:
* Update the commit message mentioning get_engines and cc stable.
(Chris)
Matthew Auld [Fri, 17 Jan 2020 13:24:13 +0000 (13:24 +0000)]
drm/i915/userptr: fix size calculation
If we create a rather large userptr object(e.g 1ULL << 32) we might
shift past the type-width of num_pages: (int)num_pages << PAGE_SHIFT,
resulting in a totally bogus sg_table, which fortunately will eventually
manifest as:
gen8_ppgtt_insert_huge:463 GEM_BUG_ON(iter->sg->length < page_size)
kernel BUG at drivers/gpu/drm/i915/gt/gen8_ppgtt.c:463!
v2: more unsigned long
prefer I915_GTT_PAGE_SIZE
Fixes: 5cc9ed4b9a7a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200117132413.1170563-2-matthew.auld@intel.com
(cherry picked from commit 8e78871bc1e5efec22c950d3fd24ddb63d4ff28a) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Bart Van Assche [Thu, 16 Jan 2020 04:47:37 +0000 (20:47 -0800)]
scsi: RDMA/isert: Fix a recently introduced regression related to logout
iscsit_close_connection() calls isert_wait_conn(). Due to commit e9d3009cb936 both functions call target_wait_for_sess_cmds() although that
last function should be called only once. Fix this by removing the
target_wait_for_sess_cmds() call from isert_wait_conn() and by only calling
isert_wait_conn() after target_wait_for_sess_cmds().
Fixes: e9d3009cb936 ("scsi: target: iscsi: Wait for all commands to finish before freeing a session"). Link: https://lore.kernel.org/r/20200116044737.19507-1-bvanassche@acm.org Reported-by: Rahul Kundu <rahul.kundu@chelsio.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Acked-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Thu, 16 Jan 2020 10:20:53 +0000 (11:20 +0100)]
scsi: fnic: do not queue commands during fwreset
When a link is going down the driver will be calling fnic_cleanup_io(),
which will traverse all commands and calling 'done' for each found command.
While the traversal is handled under the host_lock, calling 'done' happens
after the host_lock is being dropped.
As fnic_queuecommand_lck() is being called with the host_lock held, it
might well be that it will pick the command being selected for abortion
from the above routine and enqueue it for sending, but then 'done' is being
called on that very command from the above routine.
Which of course confuses the hell out of the scsi midlayer.
So fix this by not queueing commands when fnic_cleanup_io is active.
Stephan Gerhold [Fri, 17 Jan 2020 21:40:36 +0000 (13:40 -0800)]
Input: pm8xxx-vib - fix handling of separate enable register
Setting the vibrator enable_mask is not implemented correctly:
For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.
So we usually end up doing nothing when we really wanted
to enable the vibrator.
We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.
io_uring: fix compat for IORING_REGISTER_FILES_UPDATE
fds field of struct io_uring_files_update is problematic with regards
to compat user space, as pointer size is different in 32-bit, 32-on-64-bit,
and 64-bit user space. In order to avoid custom handling of compat in
the syscall implementation, make fds __u64 and use u64_to_user_ptr in
order to retrieve it. Also, align the field naturally and check that
no garbage is passed there.
Fixes: c3a31e605620c279 ("io_uring: add support for IORING_REGISTER_FILES_UPDATE") Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Masami Ichikawa [Thu, 16 Jan 2020 13:12:36 +0000 (22:12 +0900)]
tracing: Do not set trace clock if tracefs lockdown is in effect
When trace_clock option is not set and unstable clcok detected,
tracing_set_default_clock() sets trace_clock(ThinkPad A285 is one of
case). In that case, if lockdown is in effect, null pointer
dereference error happens in ring_buffer_set_clock().
Link: http://lkml.kernel.org/r/20200116131236.3866925-1-masami256@gmail.com Cc: stable@vger.kernel.org Fixes: 17911ff38aa58 ("tracing: Add locked_down checks to the open calls of files created for tracefs")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1788488 Signed-off-by: Masami Ichikawa <masami256@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
What I found out is that the expressions clear out the value once it is
resolved. As the variables are resolved in the order listed, when
processing:
delta=common_timestamp-$start
The $start is cleared. When it gets to "start2=$start", it errors out with
"unresolved symbol" (which is silent as this happens at the location of the
trace), and the histogram is dropped.
When processing the histogram for variable references, instead of adding a
new reference for a variable used twice, use the same reference. That way,
not only is it more efficient, but the order will no longer matter in
processing of the variables.
From Tom Zanussi:
"Just to clarify some more about what the problem was is that without
your patch, we would have two separate references to the same variable,
and during resolve_var_refs(), they'd both want to be resolved
separately, so in this case, since the first reference to start wasn't
part of an expression, it wouldn't get the read-once flag set, so would
be read normally, and then the second reference would do the read-once
read and also be read but using read-once. So everything worked and
you didn't see a problem:
from: start2=$start,delta=common_timestamp-$start
In the second case, when you switched them around, the first reference
would be resolved by doing the read-once, and following that the second
reference would try to resolve and see that the variable had already
been read, so failed as unset, which caused it to short-circuit out and
not do the trigger action to generate the synthetic event:
to: delta=common_timestamp-$start,start2=$start
With your patch, we only have the single resolution which happens
correctly the one time it's resolved, so this can't happen."
Link: https://lore.kernel.org/r/20200116154216.58ca08eb@gandalf.local.home Cc: stable@vger.kernel.org Fixes: 067fe038e70f6 ("tracing: Add variable reference handling to hist triggers") Reviewed-by: Tom Zanuss <zanussi@kernel.org> Tested-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Linus Torvalds [Mon, 20 Jan 2020 19:24:13 +0000 (11:24 -0800)]
Merge tag 'fixes_for_v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull reiserfs fix from Jan Kara:
"A fixup of a recently merged reiserfs fix which has caused problem
when xattrs were not compiled in"
* tag 'fixes_for_v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix handling of -EOPNOTSUPP in reiserfs_for_each_xattr
Kadlecsik József [Sun, 19 Jan 2020 21:06:49 +0000 (22:06 +0100)]
netfilter: ipset: use bitmap infrastructure completely
The bitmap allocation did not use full unsigned long sizes
when calculating the required size and that was triggered by KASAN
as slab-out-of-bounds read in several places. The patch fixes all
of them.
xiaofeng.yan [Mon, 20 Jan 2020 06:26:39 +0000 (14:26 +0800)]
hsr: Fix a compilation error
A compliation error happen when building branch 5.5-rc7
In file included from net/hsr/hsr_main.c:12:0:
net/hsr/hsr_main.h:194:20: error: two or more data types in declaration specifiers
static inline void void hsr_debugfs_rename(struct net_device *dev)
So Removed one void.
Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed") Signed-off-by: xiaofeng.yan <yanxiaofeng7@jd.com> Acked-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Wed, 15 Jan 2020 09:54:35 +0000 (10:54 +0100)]
mmc: sdhci: fix minimum clock rate for v3 controller
For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:
mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]
The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.
Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present Cc: <stable@vger.kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Niko Kortstrom [Thu, 16 Jan 2020 09:43:27 +0000 (11:43 +0200)]
net: ip6_gre: fix moving ip6gre between namespaces
Support for moving IPv4 GRE tunnels between namespaces was added in
commit b57708add314 ("gre: add x-netns support"). The respective change
for IPv6 tunnels, commit 22f08069e8b4 ("ip6gre: add x-netns support")
did not drop NETIF_F_NETNS_LOCAL flag so moving them from one netns to
another is still denied in IPv6 case. Drop NETIF_F_NETNS_LOCAL flag from
ip6gre tunnels to allow moving ip6gre tunnel endpoints between network
namespaces.
Signed-off-by: Niko Kortstrom <niko.kortstrom@nokia.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 19 Jan 2020 20:10:28 +0000 (12:10 -0800)]
Merge tag 'riscv/for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Three fixes for RISC-V:
- Don't free and reuse memory containing the code that CPUs parked at
boot reside in.
- Fix rv64 build problems for ubsan and some modules by adding
logical and arithmetic shift helpers for 128-bit values. These are
from libgcc and are similar to what's present for ARM64.
- Fix vDSO builds to clean up their own temporary files"
* tag 'riscv/for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Less inefficient gcc tishift helpers (and export their symbols)
riscv: delete temporary files
riscv: make sure the cores stay looping in .Lsecondary_park
1) Fix non-blocking connect() in x25, from Martin Schiller.
2) Fix spurious decryption errors in kTLS, from Jakub Kicinski.
3) Netfilter use-after-free in mtype_destroy(), from Cong Wang.
4) Limit size of TSO packets properly in lan78xx driver, from Eric
Dumazet.
5) r8152 probe needs an endpoint sanity check, from Johan Hovold.
6) Prevent looping in tcp_bpf_unhash() during sockmap/tls free, from
John Fastabend.
7) hns3 needs short frames padded on transmit, from Yunsheng Lin.
8) Fix netfilter ICMP header corruption, from Eyal Birger.
9) Fix soft lockup when low on memory in hns3, from Yonglong Liu.
10) Fix NTUPLE firmware command failures in bnxt_en, from Michael Chan.
11) Fix memory leak in act_ctinfo, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
cxgb4: reject overlapped queues in TC-MQPRIO offload
cxgb4: fix Tx multi channel port rate limit
net: sched: act_ctinfo: fix memory leak
bnxt_en: Do not treat DSN (Digital Serial Number) read failure as fatal.
bnxt_en: Fix ipv6 RFS filter matching logic.
bnxt_en: Fix NTUPLE firmware command failures.
net: systemport: Fixed queue mapping in internal ring map
net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec
net: dsa: sja1105: Don't error out on disabled ports with no phy-mode
net: phy: dp83867: Set FORCE_LINK_GOOD to default after reset
net: hns: fix soft lockup when there is not enough memory
net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()
net/sched: act_ife: initalize ife->metalist earlier
netfilter: nat: fix ICMP header corruption on ICMP errors
net: wan: lapbether.c: Use built-in RCU list checking
netfilter: nf_tables: fix flowtable list del corruption
netfilter: nf_tables: fix memory leak in nf_tables_parse_netdev_hooks()
netfilter: nf_tables: remove WARN and add NLA_STRING upper limits
netfilter: nft_tunnel: ERSPAN_VERSION must not be null
netfilter: nft_tunnel: fix null-attribute check
...
WARNING: CPU: 0 PID: 0 at .../kernel/trace/ftrace.c:1979 ftrace_bug+0x1ad/0x230()
...
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.116-... #1
...
[<c0314e3d>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c051a7f1>] (dump_stack+0x81/0xa8)
[<c051a7f1>] (dump_stack) from [<c0321c5d>] (warn_slowpath_common+0x69/0x90)
[<c0321c5d>] (warn_slowpath_common) from [<c0321cf3>] (warn_slowpath_null+0x17/0x1c)
[<c0321cf3>] (warn_slowpath_null) from [<c038ee9d>] (ftrace_bug+0x1ad/0x230)
[<c038ee9d>] (ftrace_bug) from [<c038f1f9>] (ftrace_process_locs+0x27d/0x444)
[<c038f1f9>] (ftrace_process_locs) from [<c08915bd>] (ftrace_init+0x91/0xe8)
[<c08915bd>] (ftrace_init) from [<c0885a67>] (start_kernel+0x34b/0x358)
[<c0885a67>] (start_kernel) from [<00308095>] (0x308095)
---[ end trace cb88537fdc8fa200 ]---
ftrace failed to modify [<c031266c>] prealloc_fixed_plts+0x8/0x60
actual: 44:f2:e1:36
ftrace record flags: 0
(0) expected tramp: c03143e9
Scenario 2, ARMv4T
==================
ftrace: allocating 14435 entries in 43 pages
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:2029 ftrace_bug+0x204/0x310
CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.5 #1
Hardware name: Cirrus Logic EDB9302 Evaluation Board
[<c0010a24>] (unwind_backtrace) from [<c000ecb0>] (show_stack+0x20/0x2c)
[<c000ecb0>] (show_stack) from [<c03c72e8>] (dump_stack+0x20/0x30)
[<c03c72e8>] (dump_stack) from [<c0021c18>] (__warn+0xdc/0x104)
[<c0021c18>] (__warn) from [<c0021d7c>] (warn_slowpath_null+0x4c/0x5c)
[<c0021d7c>] (warn_slowpath_null) from [<c0095360>] (ftrace_bug+0x204/0x310)
[<c0095360>] (ftrace_bug) from [<c04dabac>] (ftrace_init+0x3b4/0x4d4)
[<c04dabac>] (ftrace_init) from [<c04cef4c>] (start_kernel+0x20c/0x410)
[<c04cef4c>] (start_kernel) from [<00000000>] ( (null))
---[ end trace 0506a2f5dae6b341 ]---
ftrace failed to modify
[<c000c350>] perf_trace_sys_exit+0x5c/0xe8
actual: 1e:ff:2f:e1
Initializing ftrace call sites
ftrace record flags: 0
(0)
expected tramp: c000fb24
The analysis for this problem has been already performed previously,
refer to the link below.
Fix the above problems by allowing only selected reloc types in
__mcount_loc. The list itself comes from the legacy recordmcount.pl
script.
Link: https://lore.kernel.org/lkml/56961010.6000806@pengutronix.de/ Cc: stable@vger.kernel.org Fixes: ed60453fa8f8 ("ARM: 6511/1: ftrace: add ARM support for C version of recordmcount") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Rahul Lakkireddy [Fri, 17 Jan 2020 12:51:47 +0000 (18:21 +0530)]
cxgb4: reject overlapped queues in TC-MQPRIO offload
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd675 ("cxgb4: parse and configure TC-MQPRIO offload") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Fri, 17 Jan 2020 12:53:55 +0000 (18:23 +0530)]
cxgb4: fix Tx multi channel port rate limit
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8ec6 ("cxgb4: add TC-MATCHALL classifier egress offload") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Tue, 17 Dec 2019 04:06:31 +0000 (20:06 -0800)]
riscv: Less inefficient gcc tishift helpers (and export their symbols)
The existing __lshrti3 was really inefficient, and the other two helpers
are also needed to compile some modules.
Add the missing versions, and export all of the symbols like arm64
already does.
This code is based on the assembly generated by libgcc builds.
This fixes a build break triggered by ubsan:
riscv64-unknown-linux-gnu-ld: lib/ubsan.o: in function `.L2':
ubsan.c:(.text.unlikely+0x38): undefined reference to `__ashlti3'
riscv64-unknown-linux-gnu-ld: ubsan.c:(.text.unlikely+0x42): undefined reference to `__ashrti3'
Signed-off-by: Olof Johansson <olof@lixom.net>
[paul.walmsley@sifive.com: use SYM_FUNC_{START,END} instead of
ENTRY/ENDPROC; note libgcc origin] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Linus Torvalds [Sun, 19 Jan 2020 00:34:17 +0000 (16:34 -0800)]
Merge tag 'mtd/fixes-for-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"Raw NAND:
- GPMI: Fix the suspend/resume
SPI-NOR:
- Fix quad enable on Spansion like flashes
- Fix selection of 4-byte addressing opcodes on Spansion"
* tag 'mtd/fixes-for-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: gpmi: Restore nfc timing setup after suspend/resume
mtd: rawnand: gpmi: Fix suspend/resume problem
mtd: spi-nor: Fix quad enable for Spansion like flashes
mtd: spi-nor: Fix selection of 4-byte addressing opcodes on Spansion
Linus Torvalds [Sat, 18 Jan 2020 21:57:31 +0000 (13:57 -0800)]
Merge tag 'drm-fixes-2020-01-19' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Back from LCA2020, fixes wasn't too busy last week, seems to have
quieten down appropriately, some amdgpu, i915, then a core mst fix and
one fix for virtio-gpu and one for rockchip:
core mst:
- serialize down messages and clear timeslots are on unplug
amdgpu:
- Update golden settings for renoir
- eDP fix
i915:
- uAPI fix: Remove dash and colon from PMU names to comply with
tools/perf
- Fix for include file that was indirectly included
- Two fixes to make sure VMA are marked active for error capture
virtio:
- maintain obj reservation lock when submitting cmds
rockchip:
- increase link rate var size to accommodate rates"
* tag 'drm-fixes-2020-01-19' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Reorder detect_edp_sink_caps before link settings read.
drm/amdgpu: update goldensetting for renoir
drm/dp_mst: Have DP_Tx send one msg at a time
drm/dp_mst: clear time slots for ports invalid
drm/i915/pmu: Do not use colons or dashes in PMU names
drm/rockchip: fix integer type used for storing dp data rate
drm/i915/gt: Mark ring->vma as active while pinned
drm/i915/gt: Mark context->state vma as active while pinned
drm/i915/gt: Skip trying to unbind in restore_ggtt_mappings
drm/i915: Add missing include file <linux/math64.h>
drm/virtio: add missing virtio_gpu_array_lock_resv call
Linus Torvalds [Sat, 18 Jan 2020 21:02:12 +0000 (13:02 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- a resctrl fix for uninitialized objects found by debugobjects
- a resctrl memory leak fix
- fix the unintended re-enabling of the of SME and SEV CPU flags if
memory encryption was disabled at bootup via the MSR space"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Ensure clearing of SME/SEV features is maintained
x86/resctrl: Fix potential memory leak
x86/resctrl: Fix an imbalance in domain_remove_cpu()
Linus Torvalds [Sat, 18 Jan 2020 21:00:59 +0000 (13:00 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Three fixes: fix link failure on Alpha, fix a Sparse warning and
annotate/robustify a lockless access in the NOHZ code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/sched: Annotate lockless access to last_jiffies_update
lib/vdso: Make __cvdso_clock_getres() static
time/posix-stubs: Provide compat itimer supoprt for alpha
Linus Torvalds [Sat, 18 Jan 2020 20:55:19 +0000 (12:55 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes, three Intel uncore driver fixes, plus an AUX events fix
uncovered by the perf fuzzer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Remove PCIe3 unit for SNR
perf/x86/intel/uncore: Fix missing marker for snr_uncore_imc_freerunning_events
perf/x86/intel/uncore: Add PCI ID of IMC for Xeon E3 V5 Family
perf: Correctly handle failed perf_get_aux_event()
perf hists: Fix variable name's inconsistency in hists__for_each() macro
perf map: Set kmap->kmaps backpointer for main kernel map chunks
perf report: Fix incorrectly added dimensions as switch perf data file
tools lib traceevent: Fix memory leakage in filter_event
Linus Torvalds [Sat, 18 Jan 2020 20:53:28 +0000 (12:53 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Three fixes:
- Fix an rwsem spin-on-owner crash, introduced in v5.4
- Fix a lockdep bug when running out of stack_trace entries,
introduced in v5.4
- Docbook fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Fix kernel crash when spinning on RWSEM_OWNER_UNKNOWN
futex: Fix kernel-doc notation warning
locking/lockdep: Fix buffer overrun problem in stack_trace[]
Linus Torvalds [Sat, 18 Jan 2020 20:50:14 +0000 (12:50 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Three EFI fixes:
- Fix a slow-boot-scrolling regression but making sure we use WC for
EFI earlycon framebuffer mappings on x86
- Fix a mixed EFI mode boot crash
- Disable paging explicitly before entering startup_32() in mixed
mode bootup"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efistub: Disable paging at mixed mode entry
efi/libstub/random: Initialize pointer variables to zero for mixed mode
efi/earlycon: Fix write-combine mapping on x86