Thomas Gleixner [Fri, 28 Jun 2019 11:11:54 +0000 (13:11 +0200)]
x86/irq: Seperate unused system vectors from spurious entry again
Quite some time ago the interrupt entry stubs for unused vectors in the
system vector range got removed and directly mapped to the spurious
interrupt vector entry point.
Sounds reasonable, but it's subtly broken. The spurious interrupt vector
entry point pushes vector number 0xFF on the stack which makes the whole
logic in __smp_spurious_interrupt() pointless.
As a consequence any spurious interrupt which comes from a vector != 0xFF
is treated as a real spurious interrupt (vector 0xFF) and not
acknowledged. That subsequently stalls all interrupt vectors of equal and
lower priority, which brings the system to a grinding halt.
This can happen because even on 64-bit the system vector space is not
guaranteed to be fully populated. A full compile time handling of the
unused vectors is not possible because quite some of them are conditonally
populated at runtime.
Bring the entry stubs back, which wastes 160 bytes if all stubs are unused,
but gains the proper handling back. There is no point to selectively spare
some of the stubs which are known at compile time as the required code in
the IDT management would be way larger and convoluted.
Do not route the spurious entries through common_interrupt and do_IRQ() as
the original code did. Route it to smp_spurious_interrupt() which evaluates
the vector number and acts accordingly now that the real vector numbers are
handed in.
Fixup the pr_warn so the actual spurious vector (0xff) is clearly
distiguished from the other vectors and also note for the vectored case
whether it was pending in the ISR or not.
"Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen."
"Spurious interrupt vector 0xed on CPU#1. Acked."
"Spurious interrupt vector 0xee on CPU#1. Not pending!."
Fixes: 2414e021ac8d ("x86: Avoid building unused IRQ entry stubs") Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jan Beulich <jbeulich@suse.com> Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.de
Thomas Gleixner [Fri, 28 Jun 2019 11:11:53 +0000 (13:11 +0200)]
x86/irq: Handle spurious interrupt after shutdown gracefully
Since the rework of the vector management, warnings about spurious
interrupts have been reported. Robert provided some more information and
did an initial analysis. The following situation leads to these warnings:
CPU 0 CPU 1 IO_APIC
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
clear_vector()
do_IRQ()
-> vector is clear
Before the rework the vector entries of legacy interrupts were statically
assigned and occupied precious vector space while most of them were
unused. Due to that the above situation was handled silently because the
vector was handled and the core handler of the assigned interrupt
descriptor noticed that it is shut down and returned.
While this has been usually observed with legacy interrupts, this situation
is not limited to them. Any other interrupt source, e.g. MSI, can cause the
same issue.
After adding proper synchronization for level triggered interrupts, this
can only happen for edge triggered interrupts where the IO-APIC obviously
cannot provide information about interrupts in flight.
While the spurious warning is actually harmless in this case it worries
users and driver developers.
Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead
of VECTOR_UNUSED when the vector is freed up.
If that above late handling happens the spurious detector will not complain
and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on
that line will trigger the spurious warning as before.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>- Tested-by: Robert Hodaszi <Robert.Hodaszi@digi.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/20190628111440.459647741@linutronix.de
When an interrupt is shut down in free_irq() there might be an inflight
interrupt pending in the IO-APIC remote IRR which is not yet serviced. That
means the interrupt has been sent to the target CPUs local APIC, but the
target CPU is in a state which delays the servicing.
So free_irq() would proceed to free resources and to clear the vector
because synchronize_hardirq() does not see an interrupt handler in
progress.
That can trigger a spurious interrupt warning, which is harmless and just
confuses users, but it also can leave the remote IRR in a stale state
because once the handler is invoked the interrupt resources might be freed
already and therefore acknowledgement is not possible anymore.
Implement the irq_get_irqchip_state() callback for the IO-APIC irq chip. The
callback is invoked from free_irq() via __synchronize_hardirq(). Check the
remote IRR bit of the interrupt and return 'in flight' if it is set and the
interrupt is configured in level mode. For edge mode the remote IRR has no
meaning.
As this is only meaningful for level triggered interrupts this won't cure
the potential spurious interrupt warning for edge triggered interrupts, but
the edge trigger case does not result in stale hardware state. This has to
be addressed at the vector/interrupt entry level seperately.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/20190628111440.370295517@linutronix.de
Thomas Gleixner [Fri, 28 Jun 2019 11:11:51 +0000 (13:11 +0200)]
genirq: Add optional hardware synchronization for shutdown
free_irq() ensures that no hardware interrupt handler is executing on a
different CPU before actually releasing resources and deactivating the
interrupt completely in a domain hierarchy.
But that does not catch the case where the interrupt is on flight at the
hardware level but not yet serviced by the target CPU. That creates an
interesing race condition:
CPU 0 CPU 1 IRQ CHIP
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
release_resources()
do_IRQ()
-> resources are not available
That might be harmless and just trigger a spurious interrupt warning, but
some interrupt chips might get into a wedged state.
Utilize the existing irq_get_irqchip_state() callback for the
synchronization in free_irq().
synchronize_hardirq() is not using this mechanism as it might actually
deadlock unter certain conditions, e.g. when called with interrupts
disabled and the target CPU is the one on which the synchronization is
invoked. synchronize_irq() uses it because that function cannot be called
from non preemtible contexts as it might sleep.
No functional change intended and according to Marc the existing GIC
implementations where the driver supports the callback should be able
to cope with that core change. Famous last words.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/20190628111440.279463375@linutronix.de
Thomas Gleixner [Fri, 28 Jun 2019 11:11:49 +0000 (13:11 +0200)]
genirq: Delay deactivation in free_irq()
When interrupts are shutdown, they are immediately deactivated in the
irqdomain hierarchy. While this looks obviously correct there is a subtle
issue:
There might be an interrupt in flight when free_irq() is invoking the
shutdown. This is properly handled at the irq descriptor / primary handler
level, but the deactivation might completely disable resources which are
required to acknowledge the interrupt.
Split the shutdown code and deactivate the interrupt after synchronization
in free_irq(). Fixup all other usage sites where this is not an issue to
invoke the combined shutdown_and_deactivate() function instead.
This still might be an issue if the interrupt in flight servicing is
delayed on a remote CPU beyond the invocation of synchronize_irq(), but
that cannot be handled at that level and needs to be handled in the
synchronize_irq() context.
Fixes: f8264e34965a ("irqdomain: Introduce new interfaces to support hierarchy irqdomains") Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/20190628111440.098196390@linutronix.de
Thomas Gleixner [Fri, 28 Jun 2019 07:23:07 +0000 (15:23 +0800)]
x86/timer: Skip PIT initialization on modern chipsets
Recent Intel chipsets including Skylake and ApolloLake have a special
ITSSPRC register which allows the 8254 PIT to be gated. When gated, the
8254 registers can still be programmed as normal, but there are no IRQ0
timer interrupts.
Some products such as the Connex L1430 and exone go Rugged E11 use this
register to ship with the PIT gated by default. This causes Linux to fail
to boot:
Kernel panic - not syncing: IO-APIC + timer doesn't work! Boot with
apic=debug and send a report.
The panic happens before the framebuffer is initialized, so to the user, it
appears as an early boot hang on a black screen.
Affected products typically have a BIOS option that can be used to enable
the 8254 and make Linux work (Chipset -> South Cluster Configuration ->
Miscellaneous Configuration -> 8254 Clock Gating), however it would be best
to make Linux support the no-8254 case.
Modern sytems allow to discover the TSC and local APIC timer frequencies,
so the calibration against the PIT is not required. These systems have
always running timers and the local APIC timer works also in deep power
states.
So the setup of the PIT including the IO-APIC timer interrupt delivery
checks are a pointless exercise.
Skip the PIT setup and the IO-APIC timer interrupt checks on these systems,
which avoids the panic caused by non ticking PITs and also speeds up the
boot process.
Thanks to Daniel for providing the changelog, initial analysis of the
problem and testing against a variety of machines.
Reported-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Daniel Drake <drake@endlessm.com> Cc: bp@alien8.de Cc: hpa@zytor.com Cc: linux@endlessm.com Cc: rafael.j.wysocki@intel.com Cc: hdegoede@redhat.com Link: https://lkml.kernel.org/r/20190628072307.24678-1-drake@endlessm.com
Daniel Drake [Thu, 9 May 2019 05:54:17 +0000 (13:54 +0800)]
x86/tsc: Set LAPIC timer period to crystal clock frequency
The APIC timer calibration (calibrate_APIC_timer()) can be skipped
in cases where we know the APIC timer frequency. On Intel SoCs,
we believe that the APIC is fed by the crystal clock; this would make
sense, and the crystal clock frequency has been verified against the
APIC timer calibration result on ApolloLake, GeminiLake, Kabylake,
CoffeeLake, WhiskeyLake and AmberLake.
Set lapic_timer_period based on the crystal clock frequency
accordingly.
APIC timer calibration would normally be skipped on modern CPUs
by nature of the TSC deadline timer being used instead,
however this change is still potentially useful, e.g. if the
TSC deadline timer has been disabled with a kernel parameter.
calibrate_APIC_timer() uses the legacy timer, but we are seeing
new platforms that omit such legacy functionality, so avoiding
such codepaths is becoming more important.
Daniel Drake [Thu, 9 May 2019 05:54:15 +0000 (13:54 +0800)]
x86/tsc: Use CPUID.0x16 to calculate missing crystal frequency
native_calibrate_tsc() had a data mapping Intel CPU families
and crystal clock speed, but hardcoded tables are not ideal, and this
approach was already problematic at least in the Skylake X case, as
seen in commit:
b51120309348 ("x86/tsc: Fix erroneous TSC rate on Skylake Xeon")
By examining CPUID data from http://instlatx64.atw.hu/ and units
in the lab, we have found that 3 different scenarios need to be dealt
with, and we can eliminate most of the hardcoded data using an approach a
little more advanced than before:
1. ApolloLake, GeminiLake, CannonLake (and presumably all new chipsets
from this point) report the crystal frequency directly via CPUID.0x15.
That's definitive data that we can rely upon.
2. Skylake, Kabylake and all variants of those two chipsets report a
crystal frequency of zero, however we can calculate the crystal clock
speed by condidering data from CPUID.0x16.
This method correctly distinguishes between the two crystal clock
frequencies present on different Skylake X variants that caused
headaches before.
As the calculations do not quite match the previously-hardcoded values
in some cases (e.g. 23913043Hz instead of 24MHz), TSC refinement is
enabled on all platforms where we had to calculate the crystal
frequency in this way.
3. Denverton (GOLDMONT_X) reports a crystal frequency of zero and does
not support CPUID.0x16, so we leave this entry hardcoded.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Daniel Drake <drake@endlessm.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: len.brown@intel.com Cc: linux@endlessm.com Cc: rafael.j.wysocki@intel.com Link: http://lkml.kernel.org/r/20190509055417.13152-1-drake@endlessm.com Link: https://lkml.kernel.org/r/20190419083533.32388-1-drake@endlessm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Tue, 7 May 2019 02:54:57 +0000 (19:54 -0700)]
Merge branch 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Borislav Petkov:
- Support for varying MCA bank numbers per CPU: this is in preparation
for future CPU enablement (Yazen Ghannam)
- MCA banks read race fix (Tony Luck)
- Facility to filter MCEs which should not be logged (Yazen Ghannam)
- The usual round of cleanups and fixes
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE/AMD: Don't report L1 BTB MCA errors on some family 17h models
x86/MCE: Add an MCE-record filtering function
RAS/CEC: Increment cec_entered under the mutex lock
x86/mce: Fix debugfs_simple_attr.cocci warnings
x86/mce: Remove mce_report_event()
x86/mce: Handle varying MCA bank counts
x86/mce: Fix machine_check_poll() tests for error types
MAINTAINERS: Fix file pattern for X86 MCE INFRASTRUCTURE
x86/MCE: Group AMD function prototypes in <asm/mce.h>
Linus Torvalds [Tue, 7 May 2019 02:53:11 +0000 (19:53 -0700)]
Merge tag 'edac_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- amd64_edac: Family 0x17, models 0x30-.. enablement (Yazen Ghannam)
- skx_*: Librarize it so that it can be shared between drivers (Qiuxu Zhuo)
- altera: Stratix10 improvements (Thor Thayer)
- The usual round of fixes, fixlets and cleanups
* tag 'edac_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
Revert "EDAC/amd64: Support more than two controllers for chip select handling"
arm64: dts: stratix10: Use new Stratix10 EDAC bindings
Documentation: dt: edac: Add Stratix10 Peripheral bindings
Documentation: dt: edac: Fix Stratix10 IRQ bindings
EDAC/altera, firmware/intel: Add Stratix10 ECC DBE SMC call
EDAC/altera: Initialize peripheral FIFOs in probe()
EDAC/altera: Do less intrusive error injection
EDAC/amd64: Adjust printed chip select sizes when interleaved
EDAC/amd64: Support more than two controllers for chip select handling
EDAC/amd64: Recognize x16 symbol size
EDAC/amd64: Set maximum channel layer size depending on family
EDAC/amd64: Support more than two Unified Memory Controllers
EDAC/amd64: Use a macro for iterating over Unified Memory Controllers
EDAC/amd64: Add Family 17h Model 30h PCI IDs
MAINTAINERS: Add entry for EDAC-I10NM
MAINTAINERS: Update entry for EDAC-SKYLAKE
EDAC, altera: Fix S10 Double Bit Error Notification
EDAC, skx, i10nm: Make skx_common.c a pure library
Linus Torvalds [Tue, 7 May 2019 02:45:37 +0000 (19:45 -0700)]
Merge tag 'devprop-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These fix the handling of data nodes in the ACPI properties support
code, add a new helper for endpoint lookup in property graphs and
restore a comment inadvertently removed by one of previous changes.
Specifics:
- Fix the handling of data nodes in the ACPI properties support code
for devices with child devices and hierarchical _DSD properties
(Pierre-Louis Bossart).
- Add fwnode_graph_get_endpoint_by_id() helper for endpoint lookup in
device property graphs (Sakari Ailus).
- Restore the _DSD data subnodes GUID comment inadvertently removed
by one of previous changes (Shunyong Yang)"
* tag 'devprop-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / property: fix handling of data_nodes in acpi_get_next_subnode()
device property: Add fwnode_graph_get_endpoint_by_id()
ACPI: property: restore _DSD data subnodes GUID comment
Linus Torvalds [Tue, 7 May 2019 02:40:31 +0000 (19:40 -0700)]
Merge tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These fix the (Intel-specific) Performance and Energy Bias Hint (EPB)
handling and expose it to user space via sysfs, fix and clean up
several cpufreq drivers, add support for two new chips to the qoriq
cpufreq driver, fix, simplify and clean up the cpufreq core and the
schedutil governor, add support for "CPU" domains to the generic power
domains (genpd) framework and provide low-level PSCI firmware support
for that feature, fix the exynos cpuidle driver and fix a couple of
issues in the devfreq subsystem and clean it up.
Specifics:
- Fix the handling of Performance and Energy Bias Hint (EPB) on Intel
processors and expose it to user space via sysfs to avoid having to
access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor and
rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to some PM
documentation files and unify copyright notices in them (Rafael
Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to the
rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan)"
* tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
cpufreq: Fix kobject memleak
cpufreq: armada-37xx: fix frequency calculation for opp
cpufreq: centrino: Fix centrino_setpolicy() kerneldoc comment
cpufreq: qoriq: add support for lx2160a
x86: tsc: Rework time_cpufreq_notifier()
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
cpufreq: qoriq: Add ls1028a chip support
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
cpufreq: Move ->get callback check outside of __cpufreq_get()
PM / Domains: remove unnecessary unlikely()
cpufreq: Remove needless bios_limit check in show_bios_limit()
drivers/cpufreq/acpi-cpufreq.c: This fixes the following checkpatch warning
firmware/psci: add support for SYSTEM_RESET2
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
...
Linus Torvalds [Tue, 7 May 2019 02:35:13 +0000 (19:35 -0700)]
Merge tag 'acpi-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These rearrange the ACPI documentation by converting it to the .rst
format and splitting it into clear categories (admin guide, driver
API, firmware guide), switch over multiple users of a problematic
library function to a new better one, update the ACPICA code in the
kernel to a new upstream release, fix a few issues, improve power
device management diagnostics and do some cleanups.
Specifics:
- Convert the ACPI documentation in the kernel source tree to the
.rst format and split it into the admin guide, driver API and
firmware guide parts (Changbin Du).
- Add a PRP0001 usage example to the ACPI documentation (Thomas
Preston).
- Switch over the users of the acpi_dev_get_first_match_name()
library function which turned out to be problematic to a new,
better one called acpi_dev_get_first_match_dev() (Andy Shevchenko,
YueHaibing).
- Update the ACPICA code in the kernel to upstream release 20190405
including:
* Null pointer dereference check in acpi_ns_delete_node() (Erik
Schmauss).
* Multiple macro and function name changes (Bob Moore).
* Predefined operation region name fix (Erik Schmauss).
- Fix hibernation issue on systems using the Baytrail and Cherrytrail
Intel SoCs introduced during the 4.20 development cycle (Hans de
Goede).
- Add Sony VPCEH3U1E to the backlight quirk list (Zhang Rui).
- Fix button handling during system resume (Zhang Rui).
- Add a device PM diagnostic message (Rafael Wysocki).
- Clean up the code, comments and white space in multiple places
(Bjorn Helgaas, Gustavo Silva, Kefeng Wang)"
* tag 'acpi-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
Documentation: ACPI: move video_extension.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move ssdt-overlays.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move lpit.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move cppc_sysfs.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move apei/einj.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move apei/output_format.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move aml-debugger.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move method-tracing.txt to firmware-guide/acpi and convert to rsST
Documentation: ACPI: move debug.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/data-node-references.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/graph.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move acpi-lid.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move i2c-muxes.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsdt-override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move initrd_table_override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move method-customizing.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move gpio-properties.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move DSD-properties-rules.txt to firmware-guide/acpi and covert to reST
Documentation: ACPI: move scan_handlers.txt to driver-api/acpi and convert to reST
Documentation: ACPI: move linuxized-acpica.txt to driver-api/acpi and convert to reST
...
Linus Torvalds [Tue, 7 May 2019 00:54:22 +0000 (17:54 -0700)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Mostly just incremental improvements here:
- Introduce AT_HWCAP2 for advertising CPU features to userspace
- Expose SVE2 availability to userspace
- Support for "data cache clean to point of deep persistence" (DC PODP)
- Honour "mitigations=off" on the cmdline and advertise status via
sysfs
- CPU timer erratum workaround (Neoverse-N1 #1188873)
- Introduce perf PMU driver for the SMMUv3 performance counters
- Add config option to disable the kuser helpers page for AArch32 tasks
- Futex modifications to ensure liveness under contention
- Rework debug exception handling to seperate kernel and user
handlers
- Non-critical fixes and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
Documentation: Add ARM64 to kernel-parameters.rst
arm64/speculation: Support 'mitigations=' cmdline option
arm64: ssbs: Don't treat CPUs with SSBS as unaffected by SSB
arm64: enable generic CPU vulnerabilites support
arm64: add sysfs vulnerability show for speculative store bypass
arm64: Fix size of __early_cpu_boot_status
clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters
clocksource/arm_arch_timer: Remove use of workaround static key
clocksource/arm_arch_timer: Drop use of static key in arch_timer_reg_read_stable
clocksource/arm_arch_timer: Direcly assign set_next_event workaround
arm64: Use arch_timer_read_counter instead of arch_counter_get_cntvct
watchdog/sbsa: Use arch_timer_read_counter instead of arch_counter_get_cntvct
ARM: vdso: Remove dependency with the arch_timer driver internals
arm64: Apply ARM64_ERRATUM_1188873 to Neoverse-N1
arm64: Add part number for Neoverse N1
arm64: Make ARM64_ERRATUM_1188873 depend on COMPAT
arm64: Restrict ARM64_ERRATUM_1188873 mitigation to AArch32
arm64: mm: Remove pte_unmap_nested()
arm64: Fix compiler warning from pte_unmap() with -Wunused-but-set-variable
arm64: compat: Reduce address limit for 64K pages
...
Linus Torvalds [Mon, 6 May 2019 23:57:52 +0000 (16:57 -0700)]
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Linus Torvalds [Mon, 6 May 2019 23:42:54 +0000 (16:42 -0700)]
Merge tag 's390-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- Support for kernel address space layout randomization
- Add support for kernel image signature verification
- Convert s390 to the generic get_user_pages_fast code
- Convert s390 to the stack unwind API analog to x86
- Add support for CPU directed interrupts for PCI devices
- Provide support for MIO instructions to the PCI base layer, this will
allow the use of direct PCI mappings in user space code
- Add the basic KVM guest ultravisor interface for protected VMs
- Add AT_HWCAP bits for several new hardware capabilities
- Update the CPU measurement facility counter definitions to SVN 6
- Arnds cleanup patches for his quest to get LLVM compiles working
- A vfio-ccw update with bug fixes and support for halt and clear
- Improvements for the hardware TRNG code
- Another round of cleanup for the QDIO layer
- Numerous cleanups and bug fixes
* tag 's390-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (98 commits)
s390/vdso: drop unnecessary cc-ldoption
s390: fix clang -Wpointer-sign warnigns in boot code
s390: drop CONFIG_VIRT_TO_BUS
s390: boot, purgatory: pass $(CLANG_FLAGS) where needed
s390: only build for new CPUs with clang
s390: simplify disabled_wait
s390/ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
s390/unwind: introduce stack unwind API
s390/opcodes: add missing instructions to the disassembler
s390/bug: add entry size to the __bug_table section
s390: use proper expoline sections for .dma code
s390/nospec: rename assembler generated expoline thunks
s390: add missing ENDPROC statements to assembler functions
locking/lockdep: check for freed initmem in static_obj()
s390/kernel: add support for kernel address space layout randomization (KASLR)
s390/kernel: introduce .dma sections
s390/sclp: do not use static sccbs
s390/kprobes: use static buffer for insn_page
s390/kernel: convert SYSCALL and PGM_CHECK handlers to .quad
s390/kernel: build a relocatable kernel
...
Linus Torvalds [Mon, 6 May 2019 23:39:31 +0000 (16:39 -0700)]
Merge tag 'm68k-for-v5.2-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- drop arch_gettimeoffset and adopt clocksource API
- defconfig updates
* tag 'm68k-for-v5.2-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
Documentation/features/time: Mark m68k having modern-timekeeping
m68k: defconfig: Update defconfigs for v5.1-rc1
m68k: mvme16x: Handle timer counter overflow
m68k: mvme16x: Convert to clocksource API
m68k: mvme147: Handle timer counter overflow
m68k: mvme147: Convert to clocksource API
m68k: mac: Convert to clocksource API
m68k: hp300: Handle timer counter overflow
m68k: hp300: Convert to clocksource API
m68k: bvme6000: Convert to clocksource API
m68k: atari: Convert to clocksource API
m68k: amiga: Convert to clocksource API
m68k: Drop ARCH_USES_GETTIMEOFFSET
m68k: apollo, q40, sun3, sun3x: Remove arch_gettimeoffset implementations
m68k: mac: Fix VIA timer counter accesses
m68k: Call timer_interrupt() with interrupts disabled
Linus Torvalds [Mon, 6 May 2019 23:37:43 +0000 (16:37 -0700)]
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode loading update from Borislav Petkov:
"A nice Intel microcode blob loading cleanup which gets rid of the ugly
memcpy wrappers and switches the driver to use the iov_iter API. By
Jann Horn.
In addition, the /dev/cpu/microcode interface is finally deprecated as
it is inadequate for the same reasons the late microcode loading is"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Deprecate MICROCODE_OLD_INTERFACE
x86/microcode: Fix the ancient deprecated microcode loading method
x86/microcode/intel: Refactor Intel microcode blob loading
Linus Torvalds [Mon, 6 May 2019 23:33:06 +0000 (16:33 -0700)]
Merge branch 'x86-topology-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 topology updates from Ingo Molnar:
"Two main changes: preparatory changes for Intel multi-die topology
support, plus a syslog message tweak"
* 'x86-topology-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/topology: Make DEBUG_HOTPLUG_CPU0 pr_info() more descriptive
x86/smpboot: Rename match_die() to match_pkg()
topology: Simplify cputopology.txt formatting and wording
x86/topology: Fix documentation typo
Linus Torvalds [Mon, 6 May 2019 23:13:31 +0000 (16:13 -0700)]
Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm updates from Ingo Molnar:
"The changes in here are:
- text_poke() fixes and an extensive set of executability lockdowns,
to (hopefully) eliminate the last residual circumstances under
which we are using W|X mappings even temporarily on x86 kernels.
This required a broad range of surgery in text patching facilities,
module loading, trampoline handling and other bits.
- tweak page fault messages to be more informative and more
structured.
- remove DISCONTIGMEM support on x86-32 and make SPARSEMEM the
default.
- reduce KASLR granularity on 5-level paging kernels from 512 GB to
1 GB.
- misc other changes and updates"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/mm: Initialize PGD cache during mm initialization
x86/alternatives: Add comment about module removal races
x86/kprobes: Use vmalloc special flag
x86/ftrace: Use vmalloc special flag
bpf: Use vmalloc special flag
modules: Use vmalloc special flag
mm/vmalloc: Add flag for freeing of special permsissions
mm/hibernation: Make hibernation handle unmapped pages
x86/mm/cpa: Add set_direct_map_*() functions
x86/alternatives: Remove the return value of text_poke_*()
x86/jump-label: Remove support for custom text poker
x86/modules: Avoid breaking W^X while loading modules
x86/kprobes: Set instruction page as executable
x86/ftrace: Set trampoline pages as executable
x86/kgdb: Avoid redundant comparison of patched code
x86/alternatives: Use temporary mm for text poking
x86/alternatives: Initialize temporary mm for patching
fork: Provide a function for copying init_mm
uprobes: Initialize uprobes earlier
x86/mm: Save debug registers when loading a temporary mm
...
Linus Torvalds [Mon, 6 May 2019 23:11:45 +0000 (16:11 -0700)]
Merge branch 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 kdump update from Ingo Molnar:
"This includes two changes:
- Raise the crash kernel reservation limit from from ~896MB to ~4GB.
Only very old (and already known-broken) kexec-tools is supposed to
be affected by this negatively.
- Allow higher than 4GB crash kernel allocations when low allocations
fail"
* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kdump: Fall back to reserve high crashkernel memory
x86/kdump: Have crashkernel=X reserve under 4G by default
Linus Torvalds [Mon, 6 May 2019 22:56:41 +0000 (15:56 -0700)]
Merge branch 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Ingo Molnar:
"Here are the main changes in this tree:
- Introduce x86-64 IRQ/exception/debug stack guard pages to detect
stack overflows immediately and deterministically.
- Clean up over a decade worth of cruft accumulated.
The outcome of this should be more clear-cut faults/crashes when any
of the low level x86 CPU stacks overflow, instead of silent memory
corruption and sporadic failures much later on"
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
x86/irq: Fix outdated comments
x86/irq/64: Remove stack overflow debug code
x86/irq/64: Remap the IRQ stack with guard pages
x86/irq/64: Split the IRQ stack into its own pages
x86/irq/64: Init hardirq_stack_ptr during CPU hotplug
x86/irq/32: Handle irq stack allocation failure proper
x86/irq/32: Invoke irq_ctx_init() from init_IRQ()
x86/irq/64: Rename irq_stack_ptr to hardirq_stack_ptr
x86/irq/32: Rename hard/softirq_stack to hard/softirq_stack_ptr
x86/irq/32: Make irq stack a character array
x86/irq/32: Define IRQ_STACK_SIZE
x86/dumpstack/64: Speedup in_exception_stack()
x86/exceptions: Split debug IST stack
x86/exceptions: Enable IST guard pages
x86/exceptions: Disconnect IST index and stack order
x86/cpu: Remove orig_ist array
x86/cpu: Prepare TSS.IST setup for guard pages
x86/dumpstack/64: Use cpu_entry_area instead of orig_ist
x86/irq/64: Use cpu entry area instead of orig_ist
x86/traps: Use cpu_entry_area instead of orig_ist
...
Linus Torvalds [Mon, 6 May 2019 22:51:56 +0000 (15:51 -0700)]
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
"A handful of cleanups: dma-ops cleanups, missing boot time kcalloc()
check, a Sparse fix and use struct_size() to simplify a vzalloc()
call"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci: Clean up usage of X86_DEV_DMA_OPS
x86/Kconfig: Remove the unused X86_DMA_REMAP KConfig symbol
x86/kexec/crash: Use struct_size() in vzalloc()
x86/mm/tlb: Define LOADED_MM_SWITCHING with pointer-sized number
x86/platform/uv: Fix missing checks of kcalloc() return values
Linus Torvalds [Mon, 6 May 2019 22:49:54 +0000 (15:49 -0700)]
Merge branch 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cache QoS updates from Ingo Molnar:
"An RDT cleanup and a fix for RDT initialization of new resource
groups"
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Initialize a new resource group with default MBA values
x86/resctrl: Move per RDT domain initialization to a separate function
Linus Torvalds [Mon, 6 May 2019 22:47:43 +0000 (15:47 -0700)]
Merge branch 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build updates from Ingo Molnar:
"Misc updates:
- Add link flag quirk to solve LLVM linker bug that removes local
relocations, causing KASLR boot failures.
- Update the defconfigs to remove archaic partition table support
- Fix kernel growing pains: we had a bug in relocs.c handling section
header table entries count larger than 0xff00 (~65k), which can
happen with the -ffunction-sections flag, causing a build failure
with a cryptic error message. Add support for detecting the limit
and using the ELF protocol that extends the sections table via
->sh_size. The new limit is now much larger - over a billion
entries?"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tools/relocs: Fix big section header tables
x86/defconfig: Remove archaic partition tables support
x86/build: Keep local relocations with ld.lld
Linus Torvalds [Mon, 6 May 2019 22:32:35 +0000 (15:32 -0700)]
Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Ingo Molnar:
"This includes the following changes:
- cpu_has() cleanups
- sync_bitops.h modernization to the rmwcc.h facility, similarly to
bitops.h
- continued LTO annotations/fixes
- misc cleanups and smaller cleanups"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/um/vdso: Drop unnecessary cc-ldoption
x86/vdso: Rename variable to fix -Wshadow warning
x86/cpu/amd: Exclude 32bit only assembler from 64bit build
x86/asm: Mark all top level asm statements as .text
x86/build/vdso: Add FORCE to the build rule of %.so
x86/asm: Modernize sync_bitops.h
x86/mm: Convert some slow-path static_cpu_has() callers to boot_cpu_has()
x86: Convert some slow-path static_cpu_has() callers to boot_cpu_has()
x86/asm: Clarify static_cpu_has()'s intended use
x86/uaccess: Fix implicit cast of __user pointer
x86/cpufeature: Remove __pure attribute to _static_cpu_has()
Linus Torvalds [Mon, 6 May 2019 22:08:15 +0000 (15:08 -0700)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic update from Ingo Molnar:
"A single commit which unifies the unnecessarily diverged
implementations of APIC timer initialization. As a result the
max_delta parameter is now consistently taken into account"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Unify duplicated local apic timer clockevent initialization
- Continued tasklet reduction work: remove the hrtimer_tasklet
(Thomas Gleixner)
- Fix CPU hotplug remove race in the tick-broadcast mask handling
code (Thomas Gleixner)
- Force upper bound for setting CLOCK_REALTIME, to fix ABI
inconsistencies with handling values that are close to the maximum
supported and the vagueness of when uptime related wraparound might
occur. Make the consistent maximum the year 2232 across all
relevant ABIs and APIs. (Thomas Gleixner)
- various cleanups and smaller fixes"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix typos in comments
tick/broadcast: Fix warning about undefined tick_broadcast_oneshot_offline()
timekeeping: Force upper bound for setting CLOCK_REALTIME
timer/trace: Improve timer tracing
timer/trace: Replace deprecated vsprintf pointer extension %pf by %ps
timer: Move trace point to get proper index
tick/sched: Update tick_sched struct documentation
tick: Remove outgoing CPU from broadcast masks
timekeeping: Consistently use unsigned int for seqcount snapshot
softirq: Remove tasklet_hrtimer
xfrm: Replace hrtimer tasklet with softirq hrtimer
mac80211_hwsim: Replace hrtimer tasklet with softirq hrtimer
Linus Torvalds [Mon, 6 May 2019 21:44:49 +0000 (14:44 -0700)]
Merge branch 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Ingo Molnar:
"Two changes in this cycle:
- Make the /sys/devices/system/cpu/smt/* files available on all
arches, so user space has a consistent way to detect whether SMT is
enabled.
- Sparse annotation fix"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smpboot: Place the __percpu annotation correctly
cpu/hotplug: Create SMT sysfs interface for all arches
Linus Torvalds [Mon, 6 May 2019 21:31:50 +0000 (14:31 -0700)]
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Make nohz housekeeping processing more permissive and less
intrusive to isolated CPUs
- Decouple CPU-bound workqueue acconting from the scheduler and move
it into the workqueue code.
- Optimize topology building
- Better handle quota and period overflows
- Add more RCU annotations
- Comment updates, misc cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
nohz_full: Allow the boot CPU to be nohz_full
sched/isolation: Require a present CPU in housekeeping mask
kernel/cpu: Allow non-zero CPU to be primary for suspend / kexec freeze
power/suspend: Add function to disable secondaries for suspend
sched/core: Allow the remote scheduler tick to be started on CPU0
sched/nohz: Run NOHZ idle load balancer on HK_FLAG_MISC CPUs
sched/debug: Fix spelling mistake "logaritmic" -> "logarithmic"
sched/topology: Update init_sched_domains() comment
cgroup/cpuset: Update stale generate_sched_domains() comments
sched/core: Check quota and period overflow at usec to nsec conversion
sched/core: Handle overflow in cpu_shares_write_u64
sched/rt: Check integer overflow at usec to nsec conversion
sched/core: Fix typo in comment
sched/core: Make some functions static
sched/core: Unify p->on_rq updates
sched/core: Remove ttwu_activate()
sched/core, workqueues: Distangle worker accounting from rq lock
sched/fair: Remove unneeded prototype of capacity_of()
sched/topology: Skip duplicate group rewrites in build_sched_groups()
sched/topology: Fix build_sched_groups() comment
...
Linus Torvalds [Mon, 6 May 2019 21:16:36 +0000 (14:16 -0700)]
Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main kernel changes were:
- add support for Intel's "adaptive PEBS v4" - which embedds LBS data
in PEBS records and can thus batch up and reduce the IRQ (NMI) rate
significantly - reducing overhead and making call-graph profiling
less intrusive.
- add Intel CPU core and uncore support updates for Tremont, Icelake,
- extend the x86 PMU constraints scheduler with 'constraint ranges'
to better support Icelake hw constraints,
- make x86 call-chain support work better with CONFIG_FRAME_POINTER=y
- misc other changes
Tooling changes:
- updates to the main tools: 'perf record', 'perf trace', 'perf
stat'
- updated Intel and S/390 vendor events
- libtraceevent updates
- misc other updates and fixes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
perf/x86: Make perf callchains work without CONFIG_FRAME_POINTER
watchdog: Fix typo in comment
perf/x86/intel: Add Tremont core PMU support
perf/x86/intel/uncore: Add Intel Icelake uncore support
perf/x86/msr: Add Icelake support
perf/x86/intel/rapl: Add Icelake support
perf/x86/intel/cstate: Add Icelake support
perf/x86/intel: Add Icelake support
perf/x86: Support constraint ranges
perf/x86/lbr: Avoid reading the LBRs when adaptive PEBS handles them
perf/x86/intel: Support adaptive PEBS v4
perf/x86/intel/ds: Extract code of event update in short period
perf/x86/intel: Extract memory code PEBS parser for reuse
perf/x86: Support outputting XMM registers
perf/x86/intel: Force resched when TFA sysctl is modified
perf/core: Add perf_pmu_resched() as global function
perf/headers: Fix stale comment for struct perf_addr_filter
perf/core: Make perf_swevent_init_cpu() static
perf/x86: Add sanity checks to x86_schedule_events()
perf/x86: Optimize x86_schedule_events()
...
Linus Torvalds [Mon, 6 May 2019 20:50:15 +0000 (13:50 -0700)]
Merge branch 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"Here are the locking changes in this cycle:
- rwsem unification and simpler micro-optimizations to prepare for
more intrusive (and more lucrative) scalability improvements in
v5.3 (Waiman Long)
- Lockdep irq state tracking flag usage cleanups (Frederic
Weisbecker)
- static key improvements (Jakub Kicinski, Peter Zijlstra)
- misc updates, cleanups and smaller fixes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
locking/lockdep: Remove unnecessary unlikely()
locking/static_key: Don't take sleeping locks in __static_key_slow_dec_deferred()
locking/static_key: Factor out the fast path of static_key_slow_dec()
locking/static_key: Add support for deferred static branches
locking/lockdep: Test all incompatible scenarios at once in check_irq_usage()
locking/lockdep: Avoid bogus Clang warning
locking/lockdep: Generate LOCKF_ bit composites
locking/lockdep: Use expanded masks on find_usage_*() functions
locking/lockdep: Map remaining magic numbers to lock usage mask names
locking/lockdep: Move valid_state() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
locking/rwsem: Prevent unneeded warning during locking selftest
locking/rwsem: Optimize rwsem structure for uncontended lock acquisition
locking/rwsem: Enable lock event counting
locking/lock_events: Don't show pvqspinlock events on bare metal
locking/lock_events: Make lock_events available for all archs & other locks
locking/qspinlock_stat: Introduce generic lockevent_*() counting APIs
locking/rwsem: Enhance DEBUG_RWSEMS_WARN_ON() macro
locking/rwsem: Add debug check for __down_read*()
locking/rwsem: Micro-optimize rwsem_try_read_lock_unqueued()
locking/rwsem: Move rwsem internal function declarations to rwsem-xadd.h
...
Linus Torvalds [Mon, 6 May 2019 20:45:04 +0000 (13:45 -0700)]
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Ingo Molnar:
"The changes in this cycle were:
- Remove the irq timings/variance statistics code that tried to
predict when the next interrupt would occur, which didn't work out
as hoped and is replaced by another mechanism.
- This new mechanism is the 'array suffix computation' estimate,
which is superior to the previous one as it can detect not just a
single periodic pattern, but independent periodic patterns along a
log-2 scale of bucketing and exponential moving average. The
comments are longer than the code - and it works better at
predicting various complex interrupt patterns from real-world
devices than the previous estimate.
- avoid IRQ-work self-IPIs on the local CPU
- fix work-list corruption in irq_set_affinity_notifier()"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq_work: Do not raise an IPI when queueing work on the local CPU
genirq/devres: Use struct_size() in devm_kzalloc()
genirq/timings: Add array suffix computation code
genirq/timings: Remove variance computation code
genirq: Prevent use-after-free and work list corruption
Linus Torvalds [Mon, 6 May 2019 20:28:28 +0000 (13:28 -0700)]
Merge branch 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The changes in this cycle were:
- Squash a spurious warning when using the EFI framebuffer on a
non-EFI boot
- Use DMI data to annotate RAS memory errors on ARM just like we do
on Intel
- Followup cleanups for DMI
- libstub Makefile cleanups"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: Omit unneeded stripping of ksymtab/kcrctab sections
efi: Unify DMI setup code over the arm/arm64, ia64 and x86 architectures
efi/arm: Show SMBIOS bank/device location in CPER and GHES error logs
efifb: Omit memory map check on legacy boot
efi/libstub: Refactor the cmd_stubcopy Makefile command
Linus Torvalds [Mon, 6 May 2019 20:11:48 +0000 (13:11 -0700)]
Merge branch 'core-stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull stack trace updates from Ingo Molnar:
"So Thomas looked at the stacktrace code recently and noticed a few
weirdnesses, and we all know how such stories of crummy kernel code
meeting German engineering perfection end: a 45-patch series to clean
it all up! :-)
Here's the changes in Thomas's words:
'Struct stack_trace is a sinkhole for input and output parameters
which is largely pointless for most usage sites. In fact if embedded
into other data structures it creates indirections and extra storage
overhead for no benefit.
Looking at all usage sites makes it clear that they just require an
interface which is based on a storage array. That array is either on
stack, global or embedded into some other data structure.
Some of the stack depot usage sites are outright wrong, but
fortunately the wrongness just causes more stack being used for
nothing and does not have functional impact.
Another oddity is the inconsistent termination of the stack trace
with ULONG_MAX. It's pointless as the number of entries is what
determines the length of the stored trace. In fact quite some call
sites remove the ULONG_MAX marker afterwards with or without nasty
comments about it. Not all architectures do that and those which do,
do it inconsistenly either conditional on nr_entries == 0 or
unconditionally.
The following series cleans that up by:
1) Removing the ULONG_MAX termination in the architecture code
2) Removing the ULONG_MAX fixups at the call sites
3) Providing plain storage array based interfaces for stacktrace
and stackdepot.
4) Cleaning up the mess at the callsites including some related
cleanups.
5) Removing the struct stack_trace based interfaces
This is not changing the struct stack_trace interfaces at the
architecture level, but it removes the exposure to the generic
code'"
* 'core-stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
x86/stacktrace: Use common infrastructure
stacktrace: Provide common infrastructure
lib/stackdepot: Remove obsolete functions
stacktrace: Remove obsolete functions
livepatch: Simplify stack trace retrieval
tracing: Remove the last struct stack_trace usage
tracing: Simplify stack trace retrieval
tracing: Make ftrace_trace_userstack() static and conditional
tracing: Use percpu stack trace buffer more intelligently
tracing: Simplify stacktrace retrieval in histograms
lockdep: Simplify stack trace handling
lockdep: Remove save argument from check_prev_add()
lockdep: Remove unused trace argument from print_circular_bug()
drm: Simplify stacktrace handling
dm persistent data: Simplify stack trace handling
dm bufio: Simplify stack trace retrieval
btrfs: ref-verify: Simplify stack trace retrieval
dma/debug: Simplify stracktrace retrieval
fault-inject: Simplify stacktrace retrieval
mm/page_owner: Simplify stack trace handling
...
Linus Torvalds [Mon, 6 May 2019 20:01:16 +0000 (13:01 -0700)]
Merge branch 'core-speculation-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull speculation mitigation update from Ingo Molnar:
"This adds the "mitigations=" bootline option, which offers a
cross-arch set of options that will work on x86, PowerPC and s390 that
will map to the arch specific option internally"
* 'core-speculation-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390/speculation: Support 'mitigations=' cmdline option
powerpc/speculation: Support 'mitigations=' cmdline option
x86/speculation: Support 'mitigations=' cmdline option
cpu/speculation: Add 'mitigations=' cmdline option
Linus Torvalds [Mon, 6 May 2019 19:46:54 +0000 (12:46 -0700)]
Merge branch 'core-rseq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq updates from Ingo Molnar:
"A cleanup and a fix to comments"
* 'core-rseq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Remove superfluous rseq_len from task_struct
rseq: Clean up comments by reflecting removal of event counter
- a couple of straggling RCU flavor consolidation updates
- SRCU updates
- RCU CPU stall-warning updates
- torture-test updates
- an LKMM commit adding support for synchronize_srcu_expedited()
- documentation updates
- miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
net/ipv4/netfilter: Update comment from call_rcu_bh() to call_rcu()
tools/memory-model: Add support for synchronize_srcu_expedited()
doc/kprobes: Update obsolete RCU update functions
torture: Suppress false-positive CONFIG_INITRAMFS_SOURCE complaint
locktorture: NULL cxt.lwsa and cxt.lrsa to allow bad-arg detection
rcuperf: Fix cleanup path for invalid perf_type strings
rcutorture: Fix cleanup path for invalid torture_type strings
rcutorture: Fix expected forward progress duration in OOM notifier
rcutorture: Remove ->ext_irq_conflict field
rcutorture: Make rcutorture_extend_mask() comment match the code
tools/.../rcutorture: Convert to SPDX license identifier
torture: Don't try to offline the last CPU
rcu: Fix nohz status in stall warning
rcu: Move forward-progress checkers into tree_stall.h
rcu: Move irq-disabled stall-warning checking to tree_stall.h
rcu: Organize functions in tree_stall.h
rcu: Move FAST_NO_HZ stall-warning code to tree_stall.h
rcu: Inline RCU stall-warning info helper functions
rcu: Move rcu_print_task_exp_stall() to tree_exp.h
rcu: Inline RCU task stall-warning helper functions
...
Linus Torvalds [Mon, 6 May 2019 18:39:17 +0000 (11:39 -0700)]
Merge branch 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
"This is a series from Peter Zijlstra that adds x86 build-time uaccess
validation of SMAP to objtool, which will detect and warn about the
following uaccess API usage bugs and weirdnesses:
- call to %s() with UACCESS enabled
- return with UACCESS enabled
- return with UACCESS disabled from a UACCESS-safe function
- recursive UACCESS enable
- redundant UACCESS disable
- UACCESS-safe disables UACCESS
As it turns out not leaking uaccess permissions outside the intended
uaccess functionality is hard when the interfaces are complex and when
such bugs are mostly dormant.
As a bonus we now also check the DF flag. We had at least one
high-profile bug in that area in the early days of Linux, and the
checking is fairly simple. The checks performed and warnings emitted
are:
- call to %s() with DF set
- return with DF set
- return with modified stack frame
- recursive STD
- redundant CLD
It's all x86-only for now, but later on this can also be used for PAN
on ARM and objtool is fairly cross-platform in principle.
While all warnings emitted by this new checking facility that got
reported to us were fixed, there might be GCC version dependent
warnings that were not reported yet - which we'll address, should they
trigger.
The warnings are non-fatal build warnings"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
mm/uaccess: Use 'unsigned long' to placate UBSAN warnings on older GCC versions
x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation
sched/x86_64: Don't save flags on context switch
objtool: Add Direction Flag validation
objtool: Add UACCESS validation
objtool: Fix sibling call detection
objtool: Rewrite alt->skip_orig
objtool: Add --backtrace support
objtool: Rewrite add_ignores()
objtool: Handle function aliases
objtool: Set insn->func for alternatives
x86/uaccess, kcov: Disable stack protector
x86/uaccess, ftrace: Fix ftrace_likely_update() vs. SMAP
x86/uaccess, ubsan: Fix UBSAN vs. SMAP
x86/uaccess, kasan: Fix KASAN vs SMAP
x86/smap: Ditch __stringify()
x86/uaccess: Introduce user_access_{save,restore}()
x86/uaccess, signal: Fix AC=1 bloat
x86/uaccess: Always inline user_access_begin()
x86/uaccess, xen: Suppress SMAP warnings
...
Linus Torvalds [Mon, 6 May 2019 18:36:58 +0000 (11:36 -0700)]
Merge branch 'core-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull unified TLB flushing from Ingo Molnar:
"This contains the generic mmu_gather feature from Peter Zijlstra,
which is an all-arch unification of TLB flushing APIs, via the
following (broad) steps:
- enhance the <asm-generic/tlb.h> APIs to cover more arch details
- convert most TLB flushing arch implementations to the generic
<asm-generic/tlb.h> APIs.
- remove leftovers of per arch implementations
After this series every single architecture makes use of the unified
TLB flushing APIs"
* 'core-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm/resource: Use resource_overlaps() to simplify region_intersects()
ia64/tlb: Eradicate tlb_migrate_finish() callback
asm-generic/tlb: Remove tlb_table_flush()
asm-generic/tlb: Remove tlb_flush_mmu_free()
asm-generic/tlb: Remove CONFIG_HAVE_GENERIC_MMU_GATHER
asm-generic/tlb: Remove arch_tlb*_mmu()
s390/tlb: Convert to generic mmu_gather
asm-generic/tlb: Introduce CONFIG_HAVE_MMU_GATHER_NO_GATHER=y
arch/tlb: Clean up simple architectures
um/tlb: Convert to generic mmu_gather
sh/tlb: Convert SH to generic mmu_gather
ia64/tlb: Convert to generic mmu_gather
arm/tlb: Convert to generic mmu_gather
asm-generic/tlb, arch: Invert CONFIG_HAVE_RCU_TABLE_INVALIDATE
asm-generic/tlb, ia64: Conditionally provide tlb_migrate_finish()
asm-generic/tlb: Provide generic tlb_flush() based on flush_tlb_mm()
asm-generic/tlb, arch: Provide generic tlb_flush() based on flush_tlb_range()
asm-generic/tlb, arch: Provide generic VIPT cache flush
asm-generic/tlb, arch: Provide CONFIG_HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: Provide a comment
Linus Torvalds [Mon, 6 May 2019 18:28:23 +0000 (11:28 -0700)]
tty: rocket: fix incorrect forward declaration of 'rp_init()'
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
Andrey Ryabinin [Mon, 6 May 2019 10:45:27 +0000 (13:45 +0300)]
ubsan: Remove vla bound checks.
The kernel the kernel is built with -Wvla for some time, so is not
supposed to have any variable length arrays. Remove vla bounds checking
from ubsan since it's useless now.
Building lib/ubsan.c with gcc-9 results in a ton of nasty warnings like
this one:
lib/ubsan.c warning: conflicting types for built-in function
‘__ubsan_handle_negate_overflow’; expected ‘void(void *, void *)’ [-Wbuiltin-declaration-mismatch]
The kernel's declarations of __ubsan_handle_*() often uses 'unsigned
long' types in parameters while GCC these parameters as 'void *' types,
hence the mismatch.
Fix this by using 'void *' to match GCC's declarations.
* pm-devfreq:
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
PM / devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.
PM / devfreq: rockchip-dfi: Move GRF definitions to a common place.
PM / devfreq: exynos-bus: Suspend all devices on system shutdown
PM / devfreq: Fix static checker warning in try_then_request_governor
PM / devfreq: Restart previous governor if new governor fails to start
PM / devfreq: tegra: remove unneeded variable
PM / devfreq: rockchip-dfi: remove unneeded semicolon
PM / devfreq: rk3399_dmc: remove unneeded semicolon
PM / devfreq: consistent indentation
PM / devfreq: fix missing check of return value in devfreq_add_device()
PM / devfreq: fix mem leak in devfreq_add_device()
PM / devfreq: Use of_node_name_eq for node name comparisons
* pm-domains:
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
PM / Domains: remove unnecessary unlikely()
* pm-misc:
firmware/psci: add support for SYSTEM_RESET2
drivers: firmware: psci: Announce support for OS initiated suspend mode
drivers: firmware: psci: Simplify error path of psci_dt_init()
drivers: firmware: psci: Split psci_dt_cpu_init_idle()
MAINTAINERS: Update files for PSCI
drivers: firmware: psci: Move psci to separate directory
* pm-cpuidle:
PM / Domains: Add genpd governor for CPUs
cpuidle: Export the next timer expiration for CPUs
PM / Domains: Add support for CPU devices to genpd
PM / Domains: Add generic data pointer to struct genpd_power_state
cpuidle: exynos: Unify target residency for AFTR and coupled AFTR states
* pm-sleep:
PM / core: Propagate dev->power.wakeup_path when no callbacks
PM / core: Introduce dpm_async_fn() helper
PM / core: fix kerneldoc comment for device_pm_wait_for_dev()
PM / core: fix kerneldoc comment for dpm_watchdog_handler()
PM / sleep: Measure the time of filesystems syncing
PM / sleep: Refactor filesystems sync to reduce duplication
PM / wakeup: Use pm_pr_dbg() instead of pr_debug()
* acpi-doc: (25 commits)
Documentation: ACPI: move video_extension.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move ssdt-overlays.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move lpit.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move cppc_sysfs.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move apei/einj.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move apei/output_format.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move aml-debugger.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move method-tracing.txt to firmware-guide/acpi and convert to rsST
Documentation: ACPI: move debug.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/data-node-references.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/graph.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move acpi-lid.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move i2c-muxes.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsdt-override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move initrd_table_override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move method-customizing.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move gpio-properties.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move DSD-properties-rules.txt to firmware-guide/acpi and covert to reST
Documentation: ACPI: move scan_handlers.txt to driver-api/acpi and convert to reST
Documentation: ACPI: move linuxized-acpica.txt to driver-api/acpi and convert to reST
...
Merge branches 'acpi-utils', 'acpi-video', 'acpi-soc' and 'acpi-button'
* acpi-utils:
gpio: merrifield: Fix build err without CONFIG_ACPI
ACPI / utils: Remove deprecated function since no user left
ASoC: Intel: cht_bsw_rt5672: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: cht_bsw_rt5645: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcr_rt5651: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcr_rt5640: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcht_es8316: Convert to use acpi_dev_get_first_match_dev()
ASoC: Intel: bytcht_da7213: Convert to use acpi_dev_get_first_match_dev()
gpio: merrifield: Convert to use acpi_dev_get_first_match_dev()
extcon: axp288: Convert to use acpi_dev_get_first_match_dev()
ACPI / utils: Introduce acpi_dev_get_first_match_dev() helper
* acpi-video:
ACPI: video: Use vendor backlight on Sony VPCEH3U1E
* acpi-soc:
ACPI / LPSS: Use acpi_lpss_* instead of acpi_subsys_* functions for hibernate
* acpi-button:
ACPI: button: reinitialize button state upon resume
* acpica:
ACPICA: Update version to 20190405
ACPICA: Namespace: add check to avoid null pointer dereference
ACPICA: Update version to 20190329
ACPICA: utilities: fix spelling of PCC to platform_comm_channel
ACPICA: Rename nameseg length macro/define for clarity
ACPICA: Rename nameseg compare macro for clarity
ACPICA: Rename nameseg copy macro for clarity
Linus Torvalds [Sun, 5 May 2019 21:37:25 +0000 (14:37 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"I'd like to apologize for this very late pull request: I was dithering
through the week whether to send the fixes, and then yesterday Jiri's
crash fix for a regression introduced in this cycle clearly marked
perf/urgent as 'must merge now'.
Most of the commits are tooling fixes, plus there's three kernel fixes
via four commits:
- race fix in the Intel PEBS code
- fix an AUX bug and roll back a previous attempt
- fix AMD family 17h generic HW cache-event perf counters
The largest diffstat contribution comes from the AMD fix - a new event
table is introduced, which is a fairly low risk change but has a large
linecount"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix race in intel_pmu_disable_event()
perf/x86/intel/pt: Remove software double buffering PMU capability
perf/ring_buffer: Fix AUX software double buffering
perf tools: Remove needless asm/unistd.h include fixing build in some places
tools arch uapi: Copy missing unistd.h headers for arc, hexagon and riscv
tools build: Add -ldl to the disassembler-four-args feature test
perf cs-etm: Always allocate memory for cs_etm_queue::prev_packet
perf cs-etm: Don't check cs_etm_queue::prev_packet validity
perf report: Report OOM in status line in the GTK UI
perf bench numa: Add define for RUSAGE_THREAD if not present
tools lib traceevent: Change tag string for error
perf annotate: Fix build on 32 bit for BPF annotation
tools uapi x86: Sync vmx.h with the kernel
perf bpf: Return value with unlocking in perf_env__find_btf()
MAINTAINERS: Include vendor specific files under arch/*/events/*
perf/x86/amd: Update generic hardware cache events for Family 17h
Linus Torvalds [Sun, 5 May 2019 21:26:11 +0000 (14:26 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Disable function tracing during early SME setup to fix a boot crash on
SME-enabled kernels running distro kernels (some of which have
function tracing enabled)"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/mem_encrypt: Disable all instrumentation for early SME setup
Nadav Amit [Sun, 5 May 2019 01:11:24 +0000 (18:11 -0700)]
x86/mm: Initialize PGD cache during mm initialization
Poking-mm initialization might require to duplicate the PGD in early
stage. Initialize the PGD cache earlier to prevent boot failures.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: Rik van Riel <riel@surriel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4fc19708b165 ("x86/alternatives: Initialize temporary mm for patching") Link: http://lkml.kernel.org/r/20190505011124.39692-1-namit@vmware.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sun, 5 May 2019 16:28:45 +0000 (09:28 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
- a couple of ->i_link use-after-free fixes
- regression fix for wrong errno on absent device name in mount(2)
(this cycle stuff)
- ancient UFS braino in large GID handling on Solaris UFS images (bogus
cut'n'paste from large UID handling; wrong field checked to decide
whether we should look at old (16bit) or new (32bit) field)
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix braino in ufs_get_inode_gid() for solaris UFS flavour
Abort file_remove_privs() for non-reg. files
[fix] get rid of checking for absent device name in vfs_get_tree()
apparmorfs: fix use-after-free on symlink traversal
securityfs: fix use-after-free on symlink traversal
Jiri Olsa [Sat, 4 May 2019 15:15:56 +0000 (17:15 +0200)]
perf/x86/intel: Fix race in intel_pmu_disable_event()
New race in x86_pmu_stop() was introduced by replacing the
atomic __test_and_clear_bit() of cpuc->active_mask by separate
test_bit() and __clear_bit() calls in the following commit:
3966c3feca3f ("x86/perf/amd: Remove need to check "running" bit in NMI handler")
The race causes panic for PEBS events with enabled callchains:
The event is configured to make samples from PEBS drain code,
but when it's disabled, we'll go through NMI path instead,
where data->callchain will not get allocated and we'll crash:
Linus Torvalds [Fri, 3 May 2019 23:49:46 +0000 (16:49 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- PPC and ARM bugfixes from submaintainers
- Fix old Windows versions on AMD (recent regression)
- Fix old Linux versions on processors without EPT
- Fixes for LAPIC timer optimizations
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: nVMX: Fix size checks in vmx_set_nested_state
KVM: selftests: make hyperv_cpuid test pass on AMD
KVM: lapic: Check for in-kernel LAPIC before deferencing apic pointer
KVM: fix KVM_CLEAR_DIRTY_LOG for memory slots of unaligned size
x86/kvm/mmu: reset MMU context when 32-bit guest switches PAE
KVM: x86: Whitelist port 0x7e for pre-incrementing %rip
Documentation: kvm: fix dirty log ioctl arch lists
KVM: VMX: Move RSB stuffing to before the first RET after VM-Exit
KVM: arm/arm64: Don't emulate virtual timers on userspace ioctls
kvm: arm: Skip stage2 huge mappings for unaligned ipa backed by THP
KVM: arm/arm64: Ensure vcpu target is unset on reset failure
KVM: lapic: Convert guest TSC to host time domain if necessary
KVM: lapic: Allow user to disable adaptive tuning of timer advancement
KVM: lapic: Track lapic timer advance per vCPU
KVM: lapic: Disable timer advancement if adaptive tuning goes haywire
x86: kvm: hyper-v: deal with buggy TLB flush requests from WS2012
KVM: x86: Consider LAPIC TSC-Deadline timer expired if deadline too short
KVM: PPC: Book3S: Protect memslots while validating user address
KVM: PPC: Book3S HV: Perserve PSSCR FAKE_SUSPEND bit on guest exit
KVM: arm/arm64: vgic-v3: Retire pending interrupts on disabling LPIs
...
Linus Torvalds [Fri, 3 May 2019 18:42:01 +0000 (11:42 -0700)]
Merge branch 'i2c/for-current-fixed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C driver bugfixes and a MAINTAINERS update for you"
* 'i2c/for-current-fixed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Prevent runtime suspend of adapter when Host Notify is required
i2c: synquacer: fix enumeration of slave devices
MAINTAINERS: friendly takeover of i2c-gpio driver
i2c: designware: ratelimit 'transfer when suspended' errors
i2c: imx: correct the method of getting private data in notifier_call
Nicholas Piggin [Thu, 11 Apr 2019 03:34:48 +0000 (13:34 +1000)]
nohz_full: Allow the boot CPU to be nohz_full
Allow the boot CPU/CPU0 to be nohz_full. Have the boot CPU take the
do_timer duty during boot until a housekeeping CPU can take over.
This is supported when CONFIG_PM_SLEEP_SMP is not configured, or when
it is configured and the arch allows suspend on non-zero CPUs.
nohz_full has been trialed at a large supercomputer site and found to
significantly reduce jitter. In order to deploy it in production, they
need CPU0 to be nohz_full because their job control system requires
the application CPUs to start from 0, and the housekeeping CPUs are
placed higher. An equivalent job scheduling that uses CPU0 for
housekeeping could be achieved by modifying their system, but it is
preferable if nohz_full can support their environment without
modification.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lkml.kernel.org/r/20190411033448.20842-6-npiggin@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nicholas Piggin [Thu, 11 Apr 2019 03:34:47 +0000 (13:34 +1000)]
sched/isolation: Require a present CPU in housekeeping mask
During housekeeping mask setup, currently a possible CPU is required.
That does not guarantee the CPU would be available at boot time, so
check to ensure that at least one present CPU is in the mask.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lkml.kernel.org/r/20190411033448.20842-5-npiggin@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nicholas Piggin [Thu, 11 Apr 2019 03:34:46 +0000 (13:34 +1000)]
kernel/cpu: Allow non-zero CPU to be primary for suspend / kexec freeze
This patch provides an arch option, ARCH_SUSPEND_NONZERO_CPU, to
opt-in to allowing suspend to occur on one of the housekeeping CPUs
rather than hardcoded CPU0.
This will allow CPU0 to be a nohz_full CPU with a later change.
It may be possible for platforms with hardware/firmware restrictions
on suspend/wake effectively support this by handing off the final
stage to CPU0 when kernel housekeeping is no longer required. Another
option is to make housekeeping / nohz_full mask dynamic at runtime,
but the complexity could not be justified at this time.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lkml.kernel.org/r/20190411033448.20842-4-npiggin@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Nicholas Piggin [Thu, 11 Apr 2019 03:34:45 +0000 (13:34 +1000)]
power/suspend: Add function to disable secondaries for suspend
This adds a function to disable secondary CPUs for suspend that are
not necessarily non-zero / non-boot CPUs. Platforms will be able to
use this to suspend using non-zero CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lkml.kernel.org/r/20190411033448.20842-3-npiggin@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Fri, 3 May 2019 15:55:06 +0000 (08:55 -0700)]
Merge tag 'clk-fixes-for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two fixes for the NKMP clks on Allwinner SoCs, a locking fix for
clkdev where we forgot to hold a lock while iterating a list that can
change, and finally a build fix that adds some stubs for clk APIs that
are used by devfreq drivers on platforms without the clk APIs"
* tag 'clk-fixes-for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Add missing stubs for a few functions
clkdev: Hold clocks_mutex while iterating clocks list
clk: sunxi-ng: nkmp: Explain why zero width check is needed
clk: sunxi-ng: nkmp: Avoid GENMASK(-1, 0)
Linus Torvalds [Fri, 3 May 2019 15:42:03 +0000 (08:42 -0700)]
Merge tag 'sound-5.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few stable fixes at this round.
The USB Line6 audio fixes are a bit large, but they are rather trivial
and pretty much device-specific, so should be safe to apply at this
late stage. Ditto for other HD-audio quirks"
* tag 'sound-5.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Apply the fixup for ASUS Q325UAR
ALSA: line6: use dynamic buffers
ALSA: hda/realtek - Fixed Dell AIO speaker noise
ALSA: hda/realtek - Add new Dell platform for headset mode
Nick Desaulniers [Tue, 23 Apr 2019 21:00:56 +0000 (14:00 -0700)]
s390/vdso: drop unnecessary cc-ldoption
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html Cc: clang-built-linux@googlegroups.com Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390: fix clang -Wpointer-sign warnigns in boot code
The arch/s390/boot directory is built with its own set of compiler
options that does not include -Wno-pointer-sign like the rest of
the kernel does, this causes a lot of harmless but correct warnings
when building with clang.
For the atomics, we can add type casts to avoid the warnings, for
everything else the easiest way is to slightly adapt the types
to be more consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VIRT_TO_BUS is only used for legacy device PCI and ISA drivers using
virt_to_bus() instead of the streaming DMA mapping API, and the
remaining drivers generally don't work on 64-bit architectures.
Two of these drivers also cause a build warning on s390, so instead
of trying to fix that, let's just disable the option as we do on
most architectures now.
s390: boot, purgatory: pass $(CLANG_FLAGS) where needed
The purgatory and boot Makefiles do not inherit the original cflags,
so clang falls back to the default target architecture when building it,
typically this would be x86 when cross-compiling.
Add $(CLANG_FLAGS) everywhere so we pass the correct --target=s390x-linux
option when cross-compiling.
llvm does does not understand -march=z9-109 and older target
specifiers, so disable the respective Kconfig settings and
the logic to make the boot code work on old systems when
building with clang.
Part of the early boot code is normally compiled with -march=z900
for maximum compatibility. This also has to get changed with
clang to the oldest supported ISA, which is -march=z10 here.
Now that all AUX allocations are high-order by default, the software
double buffering PMU capability doesn't make sense any more, get rid
of it. In case some PMUs choose to opt out, we can re-introduce it.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: adrian.hunter@intel.com Link: http://lkml.kernel.org/r/20190503085536.24119-3-alexander.shishkin@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf/ring_buffer: Fix AUX software double buffering
This recent commit:
5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically")
overlooked the fact that the previous one page granularity of the AUX buffer
provided an implicit double buffering capability to the PMU driver, which
went away when the entire buffer became one high-order page.
Always make the full-trace mode AUX allocation at least two-part to preserve
the previous behavior and allow the implicit double buffering to continue.
Reported-by: Ammy Yi <ammy.yi@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: adrian.hunter@intel.com Fixes: 5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically") Link: http://lkml.kernel.org/r/20190503085536.24119-2-alexander.shishkin@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 3 May 2019 05:48:18 +0000 (07:48 +0200)]
Merge tag 'perf-urgent-for-mingo-5.1-20190502' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
tools UAPI:
Arnaldo Carvalho de Melo:
- Sync x86's vmx.h with the kernel.
- Copy missing unistd.h headers for arc, hexagon and riscv, fixing
a reported build regression on the ARC 32-bit architecture.
perf bench numa:
Arnaldo Carvalho de Melo:
- Add define for RUSAGE_THREAD if not present, fixing the build on the
ARC architecture when only zlib and libnuma are present.
perf BPF:
Arnaldo Carvalho de Melo:
- The disassembler-four-args feature test needs -ldl on distros such as
Mageia 7.
Bo YU:
- Fix unlocking on success in perf_env__find_btf(), detected with
the coverity tool.
libtraceevent:
Leo Yan:
- Change misleading hard coded 'trace-cmd' string in error messages.
ARM hardware tracing:
Leo Yan:
- Always allocate memory for cs_etm_queue::prev_packet, fixing a segfault
when processing CoreSight perf data.
perf annotate:
Thadeu Lima de Souza Cascardo:
- Fix build on 32 bit for BPF.
perf report:
Thomas Richter:
- Report OOM in status line in the GTK UI.
core libs:
- Remove needless asm/unistd.h that, used with sys/syscall.h ended
up redefining the syscalls defines in environments such as the
ARC arch when using uClibc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf tools: Remove needless asm/unistd.h include fixing build in some places
We were including sys/syscall.h and asm/unistd.h, since sys/syscall.h
includes asm/unistd.h, sometimes this leads to the redefinition of
defines, breaking the build.
Noticed on ARC with uCLibc.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Arnaldo Carvalho de Melo <arnaldo.melo@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Rich Felker <dalias@libc.org> Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com> Link: https://lkml.kernel.org/n/tip-xjpf80o64i2ko74aj2jih0qg@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools arch uapi: Copy missing unistd.h headers for arc, hexagon and riscv
Since those were introduced in:
c8ce48f06503 ("asm-generic: Make time32 syscall numbers optional")
But when the asm-generic/unistd.h was sync'ed with tools/ in:
1a787fc5ba18 ("tools headers uapi: Sync copy of asm-generic/unistd.h with the kernel sources")
I forgot to copy the files for the architectures that define
__ARCH_WANT_TIME32_SYSCALLS, so the perf build was breaking there, as
reported by Vineet Gupta for the ARC architecture.
After updating my ARC container to use the glibc based toolchain + cross
building libnuma, zlib and elfutils, I finally managed to reproduce the
problem and verify that this now is fixed and will not regress as will
be tested before each pull req sent upstream.
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jiri Olsa <jolsa@kernel.org> CC: linux-snps-arc@lists.infradead.org Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/r/20190426193531.GC28586@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools build: Add -ldl to the disassembler-four-args feature test
Thomas Backlund reported that the perf build was failing on the Mageia 7
distro, that is because it uses:
cat /tmp/build/perf/feature/test-disassembler-four-args.make.output
/usr/bin/ld: /usr/lib64/libbfd.a(plugin.o): in function `try_load_plugin':
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:243:
undefined reference to `dlopen'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:271:
undefined reference to `dlsym'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:256:
undefined reference to `dlclose'
/usr/bin/ld:
/home/iurt/rpmbuild/BUILD/binutils-2.32/objs/bfd/../../bfd/plugin.c:246:
undefined reference to `dlerror'
as we allow dynamic linking and loading
Reported-by: Thomas Backlund <tmb@mageia.org> Tested-by: Thomas Backlund <tmb@mageia.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Song Liu <songliubraving@fb.com> Link: https://lkml.kernel.org/r/20190501173158.GC21436@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sun, 28 Apr 2019 08:32:27 +0000 (16:32 +0800)]
perf cs-etm: Always allocate memory for cs_etm_queue::prev_packet
Robert Walker reported a segmentation fault is observed when process
CoreSight trace data; this issue can be easily reproduced by the command
'perf report --itrace=i1000i' for decoding tracing data.
If neither the 'b' flag (synthesize branches events) nor 'l' flag
(synthesize last branch entries) are specified to option '--itrace',
cs_etm_queue::prev_packet will not been initialised. After merging the
code to support exception packets and sample flags, there introduced a
number of uses of cs_etm_queue::prev_packet without checking whether it
is valid, for these cases any accessing to uninitialised prev_packet
will cause crash.
As cs_etm_queue::prev_packet is used more widely now and it's already
hard to follow which functions have been called in a context where the
validity of cs_etm_queue::prev_packet has been checked, this patch
always allocates memory for cs_etm_queue::prev_packet.
Reported-by: Robert Walker <robert.walker@arm.com> Suggested-by: Robert Walker <robert.walker@arm.com> Signed-off-by: Leo Yan <leo.yan@linaro.org> Tested-by: Robert Walker <robert.walker@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Suzuki K Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Fixes: 7100b12cf474 ("perf cs-etm: Generate branch sample for exception packet") Fixes: 24fff5eb2b93 ("perf cs-etm: Avoid stale branch samples when flush packet") Link: http://lkml.kernel.org/r/20190428083228.20246-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since cs_etm_queue::prev_packet is allocated for all cases, it will
never be NULL pointer; now validity checking prev_packet is pointless,
remove all of them.
Signed-off-by: Leo Yan <leo.yan@linaro.org> Tested-by: Robert Walker <robert.walker@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Suzuki K Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/20190428083228.20246-2-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The GUI always fails in the FINISHED_ROUND event (68) and does not
indicate the reason why.
When happened is the following. Perf report calls a lot of functions and
down deep when a FINISHED_ROUND event is processed, these functions are
called:
Now this functions runs out of memory and
returns -ENOMEM. This is reported all the way up
until function
perf_session__process_event() returns to its caller, where -ENOMEM is
changed to -EINVAL and processing stops:
if ((skip = perf_session__process_event(session, event, head)) < 0) {
pr_err("%#" PRIx64 " [%#x]: failed to process type: %d\n",
head, event->header.size, event->header.type);
err = -EINVAL;
goto out_err;
}
This occurred in the FINISHED_ROUND event when it has to process some
10000 entries and ran out of memory.
This patch indicates the root cause and displays it in the status line
of ther perf report GUI.
Output before (on GUI status line):
0xf4198 [0x8]: failed to process type: 68
Output after:
0xf4198 [0x8]: failed to process type: 68 [not enough memory]
Committer notes:
the 'skip' variable needs to be initialized to -EINVAL, so that when the
size is less than sizeof(struct perf_event_attr) we avoid this valid
compiler warning:
util/session.c: In function ‘perf_session__process_events’:
util/session.c:1936:7: error: ‘skip’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
err = skip;
~~~~^~~~~~
util/session.c:1874:6: note: ‘skip’ was declared here
s64 skip;
^~~~
cc1: all warnings being treated as errors
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Reviewed-by: Jiri Olsa <jolsa@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Link: http://lkml.kernel.org/r/20190423105303.61683-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf bench numa: Add define for RUSAGE_THREAD if not present
While cross building perf to the ARC architecture on a fedora 30 host,
we were failing with:
CC /tmp/build/perf/bench/numa.o
bench/numa.c: In function ‘worker_thread’:
bench/numa.c:1261:12: error: ‘RUSAGE_THREAD’ undeclared (first use in this function); did you mean ‘SIGEV_THREAD’?
getrusage(RUSAGE_THREAD, &rusage);
^~~~~~~~~~~~~
SIGEV_THREAD
bench/numa.c:1261:12: note: each undeclared identifier is reported only once for each function it appears in
[perfbuilder@60d5802468f6 perf]$ /arc_gnu_2019.03-rc1_prebuilt_uclibc_le_archs_linux_install/bin/arc-linux-gcc --version | head -1
arc-linux-gcc (ARCv2 ISA Linux uClibc toolchain 2019.03-rc1) 8.3.1 20190225
[perfbuilder@60d5802468f6 perf]$
Trying to reproduce a report by Vineet, I noticed that, with just
cross-built zlib and numactl libraries, I ended up with the above
failure.
So, since RUSAGE_THREAD is available as a define, check for that and
numactl libraries, I ended up with the above failure.
So, since RUSAGE_THREAD is available as a define in the system headers,
check if it is defined in the 'perf bench numa' sources and define it if
not.
Now it builds and I have to figure out if the problem reported by Vineet
only takes place if we have libelf or some other library available.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jiri Olsa <jolsa@kernel.org> Cc: linux-snps-arc@lists.infradead.org Cc: Namhyung Kim <namhyung@kernel.org> Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com> Link: https://lkml.kernel.org/n/tip-2wb4r1gir9xrevbpq7qp0amk@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Wed, 24 Apr 2019 01:38:02 +0000 (09:38 +0800)]
tools lib traceevent: Change tag string for error
The traceevent lib is used by the perf tool, and when executing
perf test -v 6
it outputs error log on the ARM64 platform:
running test 33 '*:*'trace-cmd: No such file or directory
[...]
trace-cmd: Invalid argument
The trace event parsing code originally came from trace-cmd so it keeps
the tag string "trace-cmd" for errors, this easily introduces the
impression that the perf tool launches trace-cmd command for trace event
parsing, but in fact the related parsing is accomplished by the
traceevent lib.
This patch changes the tag string to "libtraceevent" so that we can
avoid confusion and let users to more easily connect the error with
traceevent lib.
perf annotate: Fix build on 32 bit for BPF annotation
Commit 6987561c9e86 ("perf annotate: Enable annotation of BPF programs") adds
support for BPF programs annotations but the new code does not build on 32-bit.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Song Liu <songliubraving@fb.com> Fixes: 6987561c9e86 ("perf annotate: Enable annotation of BPF programs") Link: http://lkml.kernel.org/r/20190403194452.10845-1-cascardo@canonical.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2b27924bb1d4 ("KVM: nVMX: always use early vmcs check when EPT is disabled")
That causes this object in the tools/perf build process to be rebuilt:
CC /tmp/build/perf/arch/x86/util/kvm-stat.o
But it isn't using VMX_ABORT_ prefixed constants, so no change in
behaviour.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/vmx.h' differs from latest version at 'arch/x86/include/uapi/asm/vmx.h'
diff -u tools/arch/x86/include/uapi/asm/vmx.h arch/x86/include/uapi/asm/vmx.h
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: https://lkml.kernel.org/n/tip-bjbo3zc0r8i8oa0udpvftya6@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>