i2c: uniphier-f: fix misdetection of incomplete STOP condition
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Fri, 23 Sep 2016 08:56:01 +0000 (11:56 +0300)]
i2c: i801: Add support for Kaby Lake PCH-H
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add Kaby Lake PCH-H PCI ID to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an I2C GPIO multiplexer is driven by a GPIO provided by an expander
when there's a second expander using the same device driver on one of
the I2C bus segments, lockdep prints a deadlock warning when trying to
set the direction or the value of the GPIOs provided by the second
expander.
The reason for lockdep warning is that we take the chip->i2c_lock in
pca953x_gpio_set_value() or pca953x_gpio_direction_output() and then
come right back to pca953x_gpio_set_value() when the GPIO mux kicks
in. The locks actually protect different expanders, but for lockdep
both are of the same class, so it says:
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
This define is needed by i2c_adapter_depth() to detect if we don't
exceed the maximum number of lock subclasses. Make it visible even
if lockdep is disabled.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Peter Rosin <peda@axentia.se> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For crazy setups in which an i2c gpio expander is behind an i2c gpio
multiplexer controlled by a gpio provided a second expander using the
same device driver we need to explicitly tell lockdep how to handle
nested locking.
Export i2c_adapter_depth() as public API to be reused outside of i2c
core code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Peter Rosin <peda@axentia.se> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]
Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
David Wu [Thu, 22 Sep 2016 11:29:23 +0000 (19:29 +0800)]
i2c: rk3x: Fix sparse warning
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)
Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mika Westerberg [Tue, 20 Sep 2016 13:59:25 +0000 (16:59 +0300)]
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
When enumerating I2C devices connected to an I2C adapter we scan the whole
namespace (as it is possible to have devices anywhere in that namespace,
not just below the I2C adapter device) and add each found device to the I2C
bus in question.
Now after commit 525e6fabeae2 ("i2c / ACPI: add support for ACPI
reconfigure notifications") checking of the adapter handle to the one found
in the I2cSerialBus() resource was moved to happen after resources of the
I2C device has been parsed. This means that if the I2cSerialBus() resource
points to an adapter that does not exists in the system we still parse
those resources. This is problematic in particular because
acpi_dev_resource_interrupt() tries to configure GSI if the device also has
an Interrupt() resource. Failing to do that results errrors like this to be
printed on the console:
[ 10.409490] ERROR: Unable to locate IOAPIC for GSI 37
To fix this we pass the I2C adapter to i2c_acpi_get_info() and make sure
the handle matches the one in the I2cSerialBus() resource before doing
anything else to the device.
Reported-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jan Glauber [Wed, 21 Sep 2016 06:51:04 +0000 (08:51 +0200)]
i2c: octeon: Fix high-level controller status check
In case the high-level controller (HLC) is used the status code is
reported at a different location. Check that location after HLC
write operations if the ready bit is not set and return an appropriate
error code instead of always returning -EAGAIN.
Signed-off-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to a bug in the ThunderX I2C hardware sending STOP during
a recovery attempt could lock up the hardware. To work around
this problem do not send STOP at the beginning of the recovery
but use the override registers to bring the TWSI including
the high-level controller out of the bad state.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com> Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Yang Li [Mon, 12 Sep 2016 22:22:30 +0000 (17:22 -0500)]
i2c: imx: make bus recovery through pinctrl optional
Since commit 1c4b6c3bcf30 ("i2c: imx: implement bus recovery") the
driver starts to use gpio/pinctrl to support optional bus recovery
feature. But pinctrl is not always usable. There are platforms such
as ls1021a and ls1043a that don't support pinctrl, and it could just
be broken due to old/broken device tree. The patch makes it really
optional that the probe function won't bailout on pinctrl problems
instead it just disables bus recovery and prints out notification when
there is problem with pinctrl. Since pinctrl is only used by bus
recovery in this driver, move pinctrl initialization into bus recovery
init function to prevent confusion.
Signed-off-by: Li Yang <leoyang.li@nxp.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: uniphier-f: set the adapter to master mode when probing
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: uniphier: avoid WARN_ON() of clk_disable() in failure path
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Tue, 6 Sep 2016 09:50:45 +0000 (10:50 +0100)]
i2c: tegra: Fix assignment of boolean variables
Fix the following warnings reported by coccinelle for the Tegra I2C
driver.
drivers/i2c/busses/i2c-tegra.c:513:2-23: WARNING: Assignment of bool to 0/1
drivers/i2c/busses/i2c-tegra.c:539:3-24: WARNING: Assignment of bool to 0/1
Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SW Flow: For i2c message transfer, packet header and data payload is
posted and then required error/packet completion interrupts are enabled
later.
HW flow: HW process the packet just after packet header is posted, if
ARB lost/NACK error occurs (SW will not handle immediately when error
happens as error interrupts are not enabled at this point). HW assumes
error is acknowledged and clears current data in FIFO, But SW here posts
the remaining data payload which still stays in FIFO as stale data
(data without packet header).
Now once the interrupts are enabled, SW handles ARB lost/NACK error by
clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
the error and will parse/process stale data (data without packet header)
present in FIFO which causes invalid NACK errors.
Fix: Enable the error interrupts before posting the packet into FIFO
which make sure HW to not clear the fifo. Also disable the packet mode
before acknowledging errors (ARB lost/NACK error) to not process any
stale data. As error interrupts are enabled before posting the packet
header use spinlock to avoid preempting.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: tegra: use readl_poll_timeout after config_load reg programmed
After CONFIG_LOAD register is programmed instead of explicitly waiting
for timeout, use readl_poll_timeout() to check for register value to get
updated or wait till timeout.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: shmobile: Use ARCH_SHMOBILE instead of SUPERH
"i2c-sh_mobile" is used on sh7343, sh7366, sh7722, sh7723, and sh7724
only. As all of the above select ARCH_SHMOBILE, restrict its driver
dependencies from SUPERH to ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:09:05 +0000 (14:09 +0100)]
i2c: tegra: Add pinctrl support
On Tegra124/132 the pins for I2C6 are shared with the Display Port AUX
(DPAUX) channel and on Tegra210 the pins for I2C4 and I2C6 are shared
with DPAUX1 and DPAUX0, respectively. The multiplexing of the pins is
handled by a register in the DPAUX and so the Tegra DPAUX driver has
been updated to register a pinctrl device for managing these pins.
The pins for these particular I2C devices are bound to the I2C device
prior to probing. However, these I2C devices are in a different power
partition to the DPAUX devices that own the pins. Hence, it is desirable
to place the pins in the 'idle' state and allow the DPAUX power
partition to switch off, when these I2C devices is not in use.
Therefore, add calls to place the I2C pins in the 'default' and 'idle'
states when the I2C device is runtime resumed and suspended,
respectively.
Please note that the pinctrl functions that set the state of the pins
check to see if the devices has pins associated and will return zero
if they do not. Therefore, it is safe to call these pinctrl functions
even for I2C devices that do not have any pins associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:09:04 +0000 (14:09 +0100)]
i2c: tegra: Add runtime power-management support
Update the Tegra I2C driver to use runtime PM and move the code in the
tegra_i2c_clock_enable/disable() functions to the PM runtime resume and
suspend callbacks, respectively.
Note that given that CONFIG_PM is not mandatory for Tegra, if CONFIG_PM
is not enabled and so runtime PM is not enabled, ensure that the I2C
clocks are turned on during probe and kept on by calling the resume
callback directly.
In the function tegra_i2c_init(), the variable 'err' does not need to be
initialised to zero in tegra_i2c_init() because it is initialised when
pm_runtime_get_sync() is called. Furthermore, to ensure we only return 0
from tegra_i2c_init(), it is necessary to re-initialise 'err' to 0 after
a successful call to pm_runtime_get_sync() because it can return a
positive value on success. However, alternatively re-initialise 'err' by
using the return value of the function tegra_i2c_flush_fifos() because
it can only be 0 or -ETIMEDOUT.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:09:03 +0000 (14:09 +0100)]
i2c: tegra: Simplify I2C resume
The I2C adapter is unlocked regardless of whether the tegra_i2c_init()
called during the resume is successful or not. However, if the
tegra_i2c_init() is not successful, then ->is_suspended is not set to
false. Simplify the resume code by only setting ->is_suspended to false
if tegra_i2c_init() is successful and return the error code from
tegra_i2c_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:09:02 +0000 (14:09 +0100)]
i2c: tegra: Use device name for adapter name
All Tegra I2C devices have the name "Tegra I2C adapter" which is not
very useful when viewing the I2C adapter names via the sysfs. Therefore,
use the device name, which is unique for each I2C device, instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:09:01 +0000 (14:09 +0100)]
i2c: tegra: Remove non device-tree support
Tegra has only supported device-tree for platform/board configuration
for quite some time now and so simplify the Tegra I2C driver by dropping
code for non device-tree platforms/boards.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Hunter [Fri, 26 Aug 2016 13:08:58 +0000 (14:08 +0100)]
i2c: tegra: Use BIT macro
Checkpatch warns about spacing around the '<<' operator in the Tegra I2C
driver and so fix these by converting the bit definitions that are using
this operator to use the BIT macro.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lucas De Marchi [Tue, 23 Aug 2016 22:18:56 +0000 (19:18 -0300)]
i2c: designware: do not disable adapter after transfer
Disabling the adapter after each transfer adds additional delays
for each I2C transfer. Even if we don't wait for it to be disabled
anymore, on next transfer we will need to if we have several transfers
in a row.
Now during the transfer init we check if IC_TAR can be changed
dynamically, the status register for no activity and TX buffer being
empty. In this case we don't need to disable it
When a transfer fails the adapter will still be disabled - this is a
conservative approach. When transfers succeed, the adapter is left
enabled and it's configured so to disable interrupts.
Alternating register reads on 2 slaves:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00
Before:
8.638705161 seconds time elapsed ( +- 5.90% )
After:
7.516821591 seconds time elapsed ( +- 0.11% )
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Christian Ruppert <christian.ruppert@alitech.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lucas De Marchi [Tue, 23 Aug 2016 22:18:55 +0000 (19:18 -0300)]
i2c: designware: detect when dynamic tar update is possible
This adapter can be synthesized with dynamic tar update enabled or disabled.
When enabled it is not necessary to disable the adapter to change the slave
address in some situations, which saves some time per transaction.
There is no direct register to know if this feature is enabled but we can do it
indirectly by writing to the 10BIT_ADDR field in IC_CON: this field is
read only when dynamic tar update is enabled.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Christian Ruppert <christian.ruppert@alitech.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lucas De Marchi [Tue, 23 Aug 2016 22:18:54 +0000 (19:18 -0300)]
i2c: designware: add common functions for locking
These are used in 2 places and will be needed in more.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Christian Ruppert <christian.ruppert@alitech.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: designware: wait for disable/enable only if necessary
If we aren't going to continue using the controller we can just disable
it instead of waiting for it to complete. The biggest improvement here
is when a I2C transaction is completed and it doesn't block until
the adapter is disabled. When a new transfer is needed we will disable
and wait for its completion.
This way the adapter will continue changing its state in parallel to the
execution of the thread that requested the I2C transaction saving most
of the time 25~250 usec per I2C transaction.
A simple program doing a register read (1 byte write, 1 byte read)
alternating on 2 different slaves repeated 25k times for each and
measurements taken 4 times we get:
Before:
30.879317977 seconds time elapsed ( +- 14.83% )
After:
8.638705161 seconds time elapsed ( +- 5.90% )
Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Christian Ruppert <christian.ruppert@alitech.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Fri, 12 Aug 2016 14:02:54 +0000 (17:02 +0300)]
i2c: designware: Find bus speed from ACPI
Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.
As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Fri, 12 Aug 2016 14:02:53 +0000 (17:02 +0300)]
i2c: core: Add function for finding the bus speed from ACPI, take 2
ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptor which define each controller-slave
connection define the maximum speed supported by that connection.
Thus finding the maximum safe speed for the bus is to walk through all
I2cSerialBus resources that are associated to I2C controller and use the
speed of slowest connection.
Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.
This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does communication.
Previous version commit 55d38d060e99 ("i2c: core: Add function for finding
the bus speed from ACPI") got reverted due merge conflicts from
commit 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure
notifications").
This version is a bit bigger than previous version but is still sharing
the lowest and complicated part of I2cSerialBus lookup routines with the
existing code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Fri, 12 Aug 2016 14:02:52 +0000 (17:02 +0300)]
i2c: core: Cleanup I2C ACPI namespace, take 2
I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.
Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.
This is updated version from commit a7003b65801e ("i2c: core: Cleanup I2C
ACPI namespace") that got reverted due merge conflicts from
commit 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure
notifications").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Weifeng Voon [Fri, 12 Aug 2016 14:02:51 +0000 (17:02 +0300)]
i2c: designware: Enable high speed mode
This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Weifeng Voon [Fri, 12 Aug 2016 14:02:50 +0000 (17:02 +0300)]
i2c: designware: set the common config before the if else
DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Weifeng Voon [Fri, 12 Aug 2016 14:02:49 +0000 (17:02 +0300)]
i2c: designware: Enable fast mode plus
This patch enabled fast mode plus. The fast mode plus and fast speed
share the same HCNT and LCNT register. So, the fast mode plus will only
run when the HCNT and LCNT value is provided. Else, it will run at fast
speed as default.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Weifeng Voon [Fri, 12 Aug 2016 14:02:48 +0000 (17:02 +0300)]
i2c: designware: get fast plus and high speed *CNT configuration
I2C designware controller can run at fast mode plus and high speed. This
patch adds the capability to get the HCNT, LCNT configuration via
FPCN (fast plus) and HSCN (high speed) ACPI method.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Weifeng Voon [Fri, 12 Aug 2016 14:02:47 +0000 (17:02 +0300)]
i2c: designware: Move clk_freq into struct dw_i2c_dev
I2c designware controller operate speed is configured in the register
IC_CON. Previously the operate speed is determined by a local variable
clk_freq. This patch will move the local variable clk_freq into struct
dw_i2c_dev. This change will ease the set and get of the clk_freq.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jan Glauber [Wed, 24 Aug 2016 21:25:44 +0000 (23:25 +0200)]
i2c: thunderx: Add i2c driver for ThunderX SOC
The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jan Glauber [Wed, 24 Aug 2016 21:25:42 +0000 (23:25 +0200)]
i2c: octeon: Rename driver to prepare for split
This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Peter Rosin [Thu, 11 Aug 2016 14:49:54 +0000 (16:49 +0200)]
i2c: mux: inform the i2c mux core about how it is used
The i2c mux core can then take appropriate action depending on if it is
used for an actual i2c mux, for a gate or for an arbitrator (the last
is the case for these drivers). This adds support for the new clearer
and more compact devicetree bindings that was added recently.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
Peter Rosin [Sat, 9 Jul 2016 19:53:42 +0000 (21:53 +0200)]
i2c: mux: add support for 'i2c-mux', 'i2c-arb' and 'i2c-gate' DT subnodes
Backwards compatibility is preserved; the subnodes are in practice
optional.
However, the mux core needs to know what subnode it should examine, so add
a couple of new flags for i2c_mux_alloc for this purpose.
The rule is that if the mux core finds a 'reg' property in the appropriate
subnode, e.g. if 'reg' exists in the 'i2c-mux' subnode, then the mux core
will assume that this is an old style entry and not an i2c-mux subnode
(correspondingly for arbitrators and gates with 'i2c-arb' and 'i2c-gate').
Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
Peter Rosin [Fri, 8 Jul 2016 10:13:12 +0000 (12:13 +0200)]
dt-bindings: i2c: add support for 'i2c-mux' subnode
Similar to the new optional 'i2c-bus' subnode from Jon Hunter, this
adds an optional 'i2c-mux' subnode, for similar reasons. I.e. it is
bad of the i2c mux core to assume that any subnode of an i2c mux device
is a potential (when the 'reg' property matches) i2c-mux child bus,
given that i2c mux devices might do more than mux i2c traffic.
So, if an 'i2c-mux' subnode is present, dictate that all i2c-mux child
buses exist beneath that subnode.
Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Peter Rosin <peda@axentia.se>
Peter Rosin [Wed, 29 Jun 2016 13:04:03 +0000 (15:04 +0200)]
i2c: add i2c_trylock_bus wrapper, use it
This unifies usage with i2c_lock_bus and i2c_unlock_bus, and paves the
way for the next patch which looks a bit saner with this preparatory
work taken care of beforehand.
Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
eeprom: at24: check if the chip is functional in probe()
The at24 driver doesn't check if the chip is functional in its probe
function. This leads to instantiating devices that are not physically
present. For example the cape EEPROMs for BeagleBone Black are defined
in the device tree at four addresses on i2c2, but normally only one of
them is present.
If the userspace doesn't know the location in advance, it will need to
check if reading the nvmem attributes fails to determine which EEPROM
is actually there.
Try to read a single byte in probe() and bail-out with -ENODEV if the
read fails.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sun, 21 Aug 2016 21:28:24 +0000 (14:28 -0700)]
Merge branch 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull two parisc fixes from Helge Deller:
"The first patch ensures that the high-res cr16 clocksource (which was
added in kernel 4.7) gets choosen as default clocksource for parisc.
The second patch moves the #define of EREFUSED down inside errno.h and
thus unbreaks building the gccgo compiler"
* 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix order of EREFUSED define in errno.h
parisc: Fix automatic selection of cr16 clocksource
Tony Luck [Sat, 20 Aug 2016 23:27:58 +0000 (16:27 -0700)]
EDAC, skx_edac: Add EDAC driver for Skylake
This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:
1) Mapping from PCI devices to socket/memory controller is significantly
different. Skylake scatters devices on a socket across a number of
PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
Knights Landing.
Helge Deller [Sat, 20 Aug 2016 09:51:38 +0000 (11:51 +0200)]
parisc: Fix order of EREFUSED define in errno.h
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Helge Deller [Fri, 19 Aug 2016 20:39:02 +0000 (22:39 +0200)]
parisc: Fix automatic selection of cr16 clocksource
Commit 54b66800907 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.
Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Linus Torvalds [Fri, 19 Aug 2016 19:47:01 +0000 (12:47 -0700)]
Make the hardened user-copy code depend on having a hardened allocator
The kernel test robot reported a usercopy failure in the new hardened
sanity checks, due to a page-crossing copy of the FPU state into the
task structure.
This happened because the kernel test robot was testing with SLOB, which
doesn't actually do the required book-keeping for slab allocations, and
as a result the hardening code didn't realize that the task struct
allocation was one single allocation - and the sanity checks fail.
Since SLOB doesn't even claim to support hardening (and you really
shouldn't use it), the straightforward solution is to just make the
usercopy hardening code depend on the allocator supporting it.
Linus Torvalds [Fri, 19 Aug 2016 19:10:06 +0000 (12:10 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has some pretty standard driver bugfixes and one minor cleanup"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: meson: Use complete() instead of complete_all()
i2c: brcmstb: Use complete() instead of complete_all()
i2c: bcm-kona: Use complete() instead of complete_all()
i2c: bcm-iproc: Use complete() instead of complete_all()
i2c: at91: fix support of the "alternative command" feature
i2c: ocores: add missed clk_disable_unprepare() on failure paths
i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer()
i2c: mux: demux-pinctrl: properly roll back when adding adapter fails
Linus Torvalds [Fri, 19 Aug 2016 16:32:48 +0000 (09:32 -0700)]
Merge tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for DM round robin multipath path selector to disable
preemption before using this_cpu_ptr()
- a slight increase in DM crypt's mempool reserves to make swap ontop
of DM crypt more performant
- a few DM raid fixes to issues found while testing changes that were
merged in v4.8-rc1
* tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: support raid0 with missing metadata devices
dm raid: enhance attempt_restore_of_faulty_devices() to support more devices
dm raid: fix restoring of failed devices regression
dm raid: fix frozen recovery regression
dm crypt: increase mempool reserve to better support swapping
dm round robin: do not use this_cpu_ptr() without having preemption disabled
Linus Torvalds [Fri, 19 Aug 2016 16:22:50 +0000 (09:22 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. The ipr, mpt3sas and ses ones all trigger
oopses. The megaraid one fixes an attach failure on io mapped only
cards, the fcoe one is an obvious problem in the error path and the
aacraid one is a theoretical security issue (ability to trick the
kernel into a buffer overrun)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ses: Fix racy cleanup of /sys in remove_dev()
mpt3sas: Fix resume on WarpDrive flash cards
ipr: Fix sync scsi scan
megaraid_sas: Fix probing cards without io port
aacraid: Check size values after double-fetch from user
fcoe: Use kfree_skb() instead of kfree()
Linus Torvalds [Fri, 19 Aug 2016 16:21:24 +0000 (09:21 -0700)]
Merge tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for reported issues for your tree.
The normal amount of gadget fixes, xhci fixes, new device ids, and a
few other minor things. All of them have been in linux-next for a
while, the full details are in the shortlog below"
* tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
xhci: don't dereference a xhci member after removing xhci
usb: xhci: Fix panic if disconnect
xhci: really enqueue zero length TRBs.
xhci: always handle "Command Ring Stopped" events
cdc-acm: fix wrong pipe type on rx interrupt xfers
usb: misc: usbtest: add fix for driver hang
usb: dwc3: gadget: stop processing on HWO set
usb: dwc3: don't set last bit for ISOC endpoints
usb: gadget: rndis: free response queue during REMOTE_NDIS_RESET_MSG
usb: udc: core: fix error handling
usb: gadget: fsl_qe_udc: off by one in setup_received_handle()
usb/gadget: fix gadgetfs aio support.
usb: gadget: composite: Fix return value in case of error
usb: gadget: uvc: Fix return value in case of error
usb: gadget: fix check in sync read from ep in gadgetfs
usb: misc: usbtest: usbtest_do_ioctl may return positive integer
usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
usb: phy: omap-otg: Fix missing platform_set_drvdata() in omap_otg_probe()
usb: gadget: configfs: add mutex lock before unregister gadget
usb: gadget: u_ether: fix dereference after null check coverify warning
...
Linus Torvalds [Fri, 19 Aug 2016 16:06:41 +0000 (09:06 -0700)]
Merge tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs and iomap fixes from Dave Chinner:
"Changes in this update:
Regression fixes for XFS changes introduce in 4.8-rc1:
- buffer IO accounting assert failure
- ENOSPC block accounting reservation issue
- DAX IO path page cache invalidation fix
- rmapbt on-disk block count in agf
- correct classification of rmap block type when updating AGFL.
- iomap support for attribute fork mapping
Regression fixes for iomap infrastructure in 4.8-rc1:
- fiemap: honor FIEMAP_FLAG_SYNC
- fiemap: implement FIEMAP_FLAG_XATTR support to fix XFS regression
- make mark_page_accessed and pagefault_disable usage consistent with
other IO paths"
* tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remove OWN_AG rmap when allocating a block from the AGFL
xfs: (re-)implement FIEMAP_FLAG_XATTR
xfs: simplify xfs_file_iomap_begin
iomap: mark ->iomap_end as optional
iomap: prepare iomap_fiemap for attribute mappings
iomap: fiemap should honor the FIEMAP_FLAG_SYNC flag
iomap: remove superflous pagefault_disable from iomap_write_actor
iomap: remove superflous mark_page_accessed from iomap_write_actor
xfs: store rmapbt block count in the AGF
xfs: don't invalidate whole file on DAX read/write
xfs: fix bogus space reservation in xfs_iomap_write_allocate
xfs: don't assert fail on non-async buffers on ioacct decrement
Linus Torvalds [Fri, 19 Aug 2016 15:52:17 +0000 (08:52 -0700)]
Merge tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix a bug in it87 driver and URLs in ftsteutates driver"
* tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ftsteutates) Correct ftp urls in driver documentation
hwmon: (it87) Features mask must be 32 bit wide
Linus Torvalds [Fri, 19 Aug 2016 02:38:18 +0000 (19:38 -0700)]
Merge tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Daniel pointed out I'd missed some i915 fixes, and I also found a
single etnaviv fix I missed.
So here they are"
* tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux:
drm/etnaviv: take GPU lock later in the submit process
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
Linus Torvalds [Fri, 19 Aug 2016 02:31:08 +0000 (19:31 -0700)]
Merge tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- a couple of DT node ref counting fixes
- fix __unflatten_device_tree for PPC PCI hotplug case
- rework marking irq controllers as OF_POPULATED in cases where real
driver is used.
- disable of_platform_default_populate_init on PPC. The change in
initcall order causes problems which need to be sorted out later.
* tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: fix reference counting in of_graph_get_endpoint_by_regs
of/platform: disable the of_platform_default_populate_init() for all the ppc boards
ARM: imx6: mark GPC node as not populated after irq init to probe pm domain driver
of/irq: Mark interrupt controllers as populated before initialisation
drivers/of: Validate device node in __unflatten_device_tree()
of: Delete an unnecessary check before the function call "of_node_put"
Linus Torvalds [Fri, 19 Aug 2016 01:54:40 +0000 (18:54 -0700)]
Merge tag '4.8-doc-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three small fixes for Sphinx-formatted documentation generation"
* tag '4.8-doc-fixes' of git://git.lwn.net/linux:
doc-rst: customize RTD theme, drop padding of inline literal
docs: kernel-documentation: remove some highlight directives
docs: Set the Sphinx default highlight language to "guess"
Dave Airlie [Thu, 18 Aug 2016 22:51:13 +0000 (08:51 +1000)]
Merge tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Collection of i915 fixes.
* tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
Linus Torvalds [Thu, 18 Aug 2016 22:09:41 +0000 (15:09 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"An initrd microcode loading fix, and an SMP bootup topology setup fix
to resolve crashes on SGI/UV systems if the BIOS is configured in a
certain way"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Fix __max_logical_packages value setup
x86/microcode/AMD: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y
Linus Torvalds [Thu, 18 Aug 2016 22:08:31 +0000 (15:08 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Three clocksource driver fixes"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/mips-gic-timer: Make gic_clocksource_of_init() return int
clocksource/drivers/kona: Fix get_counter() error handling
clocksource/drivers/time-armada-370-xp: Fix the clock reference
Linus Torvalds [Thu, 18 Aug 2016 22:04:53 +0000 (15:04 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also start/stop filter related fixes, a perf
event read() fix, a fix uncovered by fuzzing, and an uprobes leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Check return value of the perf_event_read() IPI
perf/core: Enable mapping of the stop filters
perf/core: Update filters only on executable mmap
perf/core: Fix file name handling for start/stop filters
perf/core: Fix event_function_local()
uprobes: Fix the memcg accounting
perf intel-pt: Fix occasional decoding errors when tracing system-wide
tools: Sync kvm related header files for arm64 and s390
perf probe: Release resources on error when handling exit paths
perf probe: Check for dup and fdopen failures
perf symbols: Fix annotation of objects with debuginfo files
perf script: Don't disable use_callchain if input is pipe
perf script: Show proper message when failed list scripts
perf jitdump: Add the right header to get the major()/minor() definitions
perf ppc64le: Fix build failure when libelf is not present
perf tools mem: Fix -t store option for record command
perf intel-pt: Fix ip compression
Linus Torvalds [Thu, 18 Aug 2016 18:17:13 +0000 (11:17 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Avoid a literal load with the MMU off on the CPU resume path
(potential inconsistency between cache and RAM)
- Build error with CONFIG_ACPI=n fixed
- Compiler warning in the arch/arm64/mm/dump.c code fixed
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix shift warning in arch/arm64/mm/dump.c
arm64: kernel: avoid literal load of virtual address with MMU off
arm64: Fix NUMA build error when !CONFIG_ACPI
Linus Torvalds [Thu, 18 Aug 2016 18:09:43 +0000 (11:09 -0700)]
Merge tag 'pm-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"More hibernation-related material: one fix for a recent regression in
the core, one small cleanup of the x86-64 resume code and a
documentation update.
Specifics:
- Fix a hibernate core regression resulting from uncovering a latent
bug in its implementation of memory bitmaps by a recent commit
(James Morse).
- Use __pa() to compute a physical address in the x86-64 code
finalizing resume from hibernation (Rafael Wysocki).
- Update power management documentation related to system sleep
states to remove outdated information from it and to add a
description of a recently introduced hibernation debug feature to
it (Rafael Wysocki)"
* tag 'pm-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / hibernate: Fix rtree_next_node() to avoid walking off list ends
x86/power/64: Use __pa() for physical address computation
PM / sleep: Update some system sleep documentation
Linus Torvalds [Thu, 18 Aug 2016 17:58:50 +0000 (10:58 -0700)]
Merge tag 'drm-fixes-for-4.8-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Pretty quiet so far:
- a few amdgpu/radeon fixup for pcie pm changes
- a couple of amdgpu fixes
- some build fixes
- printk fix"
* tag 'drm-fixes-for-4.8-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: Change GART offset to 64-bit
drm/mediatek: add ARM_SMCCC dependency
drm/mediatek: add CONFIG_OF dependency
drm/mediatek: add COMMON_CLK dependency
drm/amdgpu: Fix memory trashing if UVD ring test fails
drm/amdgpu: fix vm init error path
drm/amdkfd: print doorbell offset as a hex value
Revert "drm/radeon: work around lack of upstream ACPI support for D3cold"
Revert "drm/amdgpu: work around lack of upstream ACPI support for D3cold"
Johannes Berg [Thu, 11 Aug 2016 09:50:22 +0000 (11:50 +0200)]
locking/barriers: Suppress sparse warnings in lockless_dereference()
After Peter's commit:
331b6d8c7afc ("locking/barriers: Validate lockless_dereference() is used on a pointer type")
... we get a lot of sparse warnings (one for every rcu_dereference, and more)
since the expression here is assigning to the wrong address space.
Instead of validating that 'p' is a pointer this way, instead make
it fail compilation when it's not by using sizeof(*(p)). This will
not cause any sparse warnings (tested, likely since the address
space is irrelevant for sizeof), and will fail compilation when
'p' isn't a pointer type.
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 331b6d8c7afc ("locking/barriers: Validate lockless_dereference() is used on a pointer type") Link: http://lkml.kernel.org/r/1470909022-687-2-git-send-email-johannes@sipsolutions.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
Johannes Berg [Thu, 11 Aug 2016 09:50:21 +0000 (11:50 +0200)]
Revert "drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference"
This reverts commit:
fa7d81bb3c269 ("drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference")
As Peter explained:
[...] lockless_dereference() is _stronger_ than READ_ONCE(), not weaker.
[...]
Also, clue is in the name: 'dereference', you don't actually dereference
the pointer here, only load it.
My next patch breaks the compile without this revert, because it assumes
you want to deference and thus also need the struct type visible (which
it isn't here), so revert it.
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1470909022-687-1-git-send-email-johannes@sipsolutions.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
On an i5 laptop, 4 pCPUs, 4vCPUs for one full dynticks guest, there are four
CPU hog processes(for loop) running in the guest, I hot-unplug the pCPUs
on host one by one until there is only one left, then observe CPU utilization
via 'top' in the guest, it shows:
100% st for cpu0(housekeeping)
75% st for other CPUs (nohz full mode)
However, w/o this commit it shows the correct 75% for all four CPUs.
When a guest is interrupted for a longer amount of time, missed clock ticks
are not redelivered later. Because of that, we should not limit the amount
of steal time accounted to the amount of time that the calling functions
think have passed.
However, the interval returned by account_other_time() is NOT rounded down
to the nearest jiffy, while the base interval in get_vtime_delta() it is
subtracted from is, so the max cputime limit is required to avoid underflow.
This patch fixes the regression by limiting the account_other_time() from
get_vtime_delta() to avoid underflow, and lets the other three call sites
(in account_other_time() and steal_account_process_time()) account however
much steal time the host told us elapsed.
Suggested-by: Rik van Riel <riel@redhat.com> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krcmar <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Link: http://lkml.kernel.org/r/1471399546-4069-1-git-send-email-wanpeng.li@hotmail.com
[ Improved the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>