From 25d2ee9f1b22dc62d06265420296a8cd150ad272 Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Wed, 6 Jun 2018 17:54:07 +0200 Subject: [PATCH] ARM: dts: am335x-sl50: use phy-phandle declarations phy-phandle is now a preferred method to reference a PHY device. The new method also allows you to specify a reset gpio which is required for this board. Signed-off-by: Enric Balletbo i Serra Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-sl50.dts | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/am335x-sl50.dts index dedf54d358ae..ef8f428bf660 100644 --- a/arch/arm/boot/dts/am335x-sl50.dts +++ b/arch/arm/boot/dts/am335x-sl50.dts @@ -256,6 +256,8 @@ davinci_mdio_default: davinci_mdio_default { /* MDIO */ AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + /* Ethernet */ + AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7) /* Ethernet_nRST - gpmc_ad14.gpio1_14 */ >; }; @@ -327,7 +329,6 @@ AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7) /* SoundPA_en - mcasp0_fsr.gpio3_19 AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7) /* nKbdOnC - gpmc_ad10.gpio0_26 */ AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdInt - gpmc_ad12.gpio1_12 */ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdReset - gpmc_ad13.gpio1_13 */ - AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7) /* nDispReset - gpmc_ad14.gpio1_14 */ AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7) /* USB1_enPower - gpmc_a1.gpio1_17 */ /* PDI Bus - Battery system */ AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7) /* nBattReset gpmc_a0.gpio1_16 */ @@ -556,13 +557,8 @@ ldo4_reg: regulator@6 { }; &cpsw_emac0 { - phy_id = <&davinci_mdio>, <0>; - phy-mode = "mii"; -}; - -&cpsw_emac1 { - phy_id = <&davinci_mdio>, <1>; phy-mode = "mii"; + phy-handle = <ðphy0>; }; &mac { @@ -577,6 +573,12 @@ &davinci_mdio { pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; + reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + reset-delay-us = <100>; /* PHY datasheet states 100us min */ + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; }; &sham { -- 2.45.2