From 3a33467f42bf728119533e5f9d376574c48003a9 Mon Sep 17 00:00:00 2001 From: Gregory CLEMENT Date: Wed, 9 Nov 2016 23:59:30 +0100 Subject: [PATCH] ARM: dts: armada-375: Use the node labels Use the node label when possible. As a result it flattens the device tree Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-375-db.dts | 269 ++++++++++++++-------------- 1 file changed, 136 insertions(+), 133 deletions(-) diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts index cded5f0a262d..b33a674088ed 100644 --- a/arch/arm/boot/dts/armada-375-db.dts +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -69,138 +69,141 @@ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000 MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>; - internal-regs { - spi@10600 { - pinctrl-0 = <&spi0_pins>; - pinctrl-names = "default"; - /* - * SPI conflicts with NAND, so we disable it - * here, and select NAND as the enabled device - * by default. - */ - status = "disabled"; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "n25q128a13", "jedec,spi-nor"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <108000000>; - }; - }; - - i2c@11000 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-0 = <&i2c0_pins>; - pinctrl-names = "default"; - }; - - i2c@11100 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-0 = <&i2c1_pins>; - pinctrl-names = "default"; - }; - - serial@12000 { - status = "okay"; - }; - - pinctrl { - sdio_st_pins: sdio-st-pins { - marvell,pins = "mpp44", "mpp45"; - marvell,function = "gpio"; - }; - }; - - sata@a0000 { - status = "okay"; - nr-ports = <2>; - }; - - nand: nand@d0000 { - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - status = "okay"; - num-cs = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partition@0 { - label = "U-Boot"; - reg = <0 0x800000>; - }; - partition@800000 { - label = "Linux"; - reg = <0x800000 0x800000>; - }; - partition@1000000 { - label = "Filesystem"; - reg = <0x1000000 0x3f000000>; - }; - }; - - usb@54000 { - status = "okay"; - }; - - usb3@58000 { - status = "okay"; - }; - - mvsdio@d4000 { - pinctrl-0 = <&sdio_pins &sdio_st_pins>; - pinctrl-names = "default"; - status = "okay"; - cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - - mdio { - phy0: ethernet-phy@0 { - reg = <0>; - }; - - phy3: ethernet-phy@3 { - reg = <3>; - }; - }; - - ethernet@f0000 { - status = "okay"; - - eth0@c4000 { - status = "okay"; - phy = <&phy0>; - phy-mode = "rgmii-id"; - }; - - eth1@c5000 { - status = "okay"; - phy = <&phy3>; - phy-mode = "gmii"; - }; - }; - }; - - pcie-controller { - status = "okay"; - /* - * The two PCIe units are accessible through - * standard PCIe slots on the board. - */ - pcie@1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - pcie@2,0 { - /* Port 1, Lane 0 */ - status = "okay"; - }; - }; }; }; +&pciec { + status = "okay"; +}; + +/* + * The two PCIe units are accessible through + * standard PCIe slots on the board. + */ +&pcie0 { + /* Port 0, Lane 0 */ + status = "okay"; +}; + +&pcie1 { + /* Port 1, Lane 0 */ + status = "okay"; +}; + + +&spi0 { + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + + /* + * SPI conflicts with NAND, so we disable it here, and + * select NAND as the enabled device by default. + */ + + status = "disabled"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "n25q128a13", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + }; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; +}; + +&uart0 { + status = "okay"; +}; + +&pinctrl { + sdio_st_pins: sdio-st-pins { + marvell,pins = "mpp44", "mpp45"; + marvell,function = "gpio"; + }; +}; + +&sata { + status = "okay"; + nr-ports = <2>; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; +}; + +&usb1 { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; + +&sdio { + pinctrl-0 = <&sdio_pins &sdio_st_pins>; + pinctrl-names = "default"; + status = "okay"; + cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; +}; + +&mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy3: ethernet-phy@3 { + reg = <3>; + }; +}; + +ðernet { + status = "okay"; +}; + + +ð0 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; + +ð1 { + status = "okay"; + phy = <&phy3>; + phy-mode = "gmii"; +}; -- 2.45.2