From 92537d65d58ede86d752d1390cf3b51480ab0179 Mon Sep 17 00:00:00 2001 From: Pankaj Dubey Date: Mon, 11 Apr 2016 13:12:23 +0530 Subject: [PATCH] dt-bindings: EXYNOS: Add exynos-srom device tree binding This patch adds exynos-srom binding information for SROM Controller driver on Exynos SoCs. Documentation for new subnode properties, allowing bank configuration are added based on u-boot implementation, but heavily reworked. CC: Rob Herring CC: Mark Rutland CC: Ian Campbell Signed-off-by: Pankaj Dubey [p.fedin: Added SROMc configuration description and fixed SROMc mapping] Signed-off-by: Pavel Fedin Reviewed-by: Krzysztof Kozlowski Signed-off-by: Kukjin Kim Signed-off-by: Krzysztof Kozlowski --- .../memory-controllers/exynos-srom.txt | 79 +++++++++++++++++++ 1 file changed, 79 insertions(+) create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt new file mode 100644 index 000000000000..f633b5d0f8ca --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt @@ -0,0 +1,79 @@ +SAMSUNG Exynos SoCs SROM Controller driver. + +Required properties: +- compatible : Should contain "samsung,exynos4210-srom". + +- reg: offset and length of the register set + +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + 0 + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, in addition to regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + +Example: basic definition, no banks are configured + memory-controller@12570000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; -- 2.45.2