From d11ece801891c71d34fbb4500956bdf797355db9 Mon Sep 17 00:00:00 2001 From: Anson Huang Date: Tue, 8 Oct 2019 09:25:53 +0800 Subject: [PATCH] arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort The iomuxc node is being put at end of file because of its huge pinctrl data. I2C devices should be placed in alphabetical sort. Signed-off-by: Anson Huang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 124 +++++++++---------- 1 file changed, 62 insertions(+), 62 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts index f7a15f3904c2..f6d367cdf31d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts @@ -94,68 +94,6 @@ ethphy0: ethernet-phy@0 { }; }; -&sai3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_sai3>; - assigned-clocks = <&clk IMX8MM_CLK_SAI3>; - assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; - assigned-clock-rates = <24576000>; - status = "okay"; -}; - -&snvs_pwrkey { - status = "okay"; -}; - -&uart2 { /* console */ - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; - status = "okay"; -}; - -&usbotg1 { - dr_mode = "otg"; - hnp-disable; - srp-disable; - adp-disable; - usb-role-switch; - status = "okay"; - - port { - usb1_drd_sw: endpoint { - remote-endpoint = <&typec1_dr_sw>; - }; - }; -}; - -&usdhc2 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; - pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; - pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; - cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - bus-width = <4>; - vmmc-supply = <®_usdhc2_vmmc>; - status = "okay"; -}; - -&usdhc3 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc3>; - pinctrl-1 = <&pinctrl_usdhc3_100mhz>; - pinctrl-2 = <&pinctrl_usdhc3_200mhz>; - bus-width = <8>; - non-removable; - status = "okay"; -}; - -&wdog1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_wdog>; - fsl,ext-reset-output; - status = "okay"; -}; - &i2c1 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -306,6 +244,68 @@ typec1_con: connector { }; }; +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + usb-role-switch; + status = "okay"; + + port { + usb1_drd_sw: endpoint { + remote-endpoint = <&typec1_dr_sw>; + }; + }; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + &iomuxc { pinctrl-names = "default"; -- 2.45.2